Littelfuse SMDJ User Manual

Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
SMDJ Series
Uni-directional
Bi-directional
Agency Approvals
AGENCY AGENCY FILE NUMBER
E230531
Maximum Ratings and Thermal Characteristics (T
=25°C unless otherwise noted)
A
Parameter Symbol Value Unit
Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2)
Power Dissipation on Infinite Heat Sink at T
Peak For ward Surge Current, 8.3ms Single Half Sine Wave (Note 3)
Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only
Operating Junction and Storage Temperature Range
Typical Thermal Resistance Junction to Lead
Typical Thermal Resistance Junction to Ambient
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above T
2. Mounted on copper pad area of 0.31x0.31” (8.0 × 8.0mm) to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum.
=50°C
A
P
PPM
P
M(AV)
I
FSM
V
F
, T
T
J
R
uJL
R
uJA
3000 W
300 A
-55 to 150 °C
STG
= 25°C per Fig. 3.
A
6.5 W
3.5 V
15 °C/W
75 °C/W
RoHS
Description
The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
Features
• For surface mounted
applications in order to optimize board space
• Low prole package
• Typical failure mode is
short from over-specified voltage or current
• Whisker test is conducted
based on JEDEC JESD201A per its table 4a and 4c
• IEC-61000-4-2 ESD
15kV(Air), 8kV (Contact)
• ESD protection of data
lines in accordance with IEC 61000-4-2 (IEC801-2)
• EFT protection of data
lines in accordance with IEC 61000-4-4 (IEC801-4)
• Built-in strain relief
VBR @TJ= VBR@25°C × (1+αT
x (TJ - 25))
(αT: Temperature Coefficient)
• Glass passivated chip
junction
• 3000W peak pulse power
capability at 10/1000μs waveform, repetition rate (duty cycles):0.01%
• Fast response time:
typically less than 1.0ps
from 0V to BV min
• Excellent clamping
capability
• Low incremental surge
resistance
• Typical I
less than 2µA
R
above 12V
• High temperature
soldering guaranteed: 260°C/40 seconds at terminals
• Plastic package has
underwriters laboratory flammability 94V-O
• Meet MSL level1, per
J-STD-020, LF maximum peak of 260°C
• Matte tin lead–free plated
• Halogen free and RoHS
compliant
Applications
TVS devices are ideal for the protection of I/O Interfaces, V
bus and other vulnerable circuits used in Telecom,
CC
Computer, Industrial and Consumer electronic applications.
Functional Diagram
Bi-directional
Cathode
Uni-directional
© 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/24/14
Anode
Additional Information
Datasheet
Resources
Samples
Transient Voltage Suppression Diodes
Surface Mount – 3000W > SMDJ series
Electrical Characteristics (T
=25°C unless otherwise noted)
A
Reverse
Part
Number
(Uni)
Part
Number
(Bi)
Marking
Stand off
Voltage
UNI BI MIN MAX
SMDJ5.0A SMDJ6.0A SMDJ6.5A
SMDJ7.0A
SMDJ7.5A SMDJ8.0A SMDJ8.5A SMDJ9.0A
SMDJ10A
SMDJ11A SMDJ12A SMDJ13A SMDJ14A SMDJ15A SMDJ16A SMDJ17A SMDJ18A SMDJ20A SMDJ22A SMDJ24A SMDJ26A SMDJ28A SMDJ30A SMDJ33A SMDJ36A SMDJ40A SMDJ43A SMDJ45A SMDJ48A SMDJ51A SMDJ54A SMDJ58A SMDJ60A SMDJ64A SMDJ70A SMDJ75A SMDJ78A SMDJ85A SMDJ90A
SMDJ100A SMDJ110A SMDJ120A SMDJ130A SMDJ150A SMDJ160A SMDJ170A SMDJ180A SMDJ220A
For parts without A , the VBR is + 10%, and VC is 5% higher than A parts.
For bidirectional type having V
SMDJ5.0CA RDE DDE 5.0 6.40 7. 0 0 10 9.2 326.1 800 X SMDJ6.0CA RDG DDG 6.0 6.67 7.37 10 10.3 291.3 800 X SMDJ6.5CA RDK DDK 6.5 7.22 7.98 10 11. 2 267.9 500 X
SMDJ7.0CA PDM DDM 7. 0 7.78 8.60 10 12.0 250.0 200 X
SMDJ7.5CA PDP DDP 7. 5 8.33 9.21 1 12.9 232.6 10 0 X SMDJ8.0CA PDR DDR 8.0 8.89 9.83 1 13.6 220.6 50 X SMDJ8.5CA PDT DDT 8.5 9.44 10.40 1 14.4 208.3 20 X SMDJ9.0CA PDV DDV 9.0 10.00 11. 10 1 15.4 194.8 10 X
SMDJ10CA PDX DDX 10.0 11. 10 12.30 1 1 7. 0 176.5 5 X
SMDJ11CA PDZ DDZ 11. 0 12.20 13.50 1 18.2 164.8 2 X SMDJ12CA PEE DEE 12.0 13.30 14.70 1 19.9 150.8 2 X SMDJ13CA PEG DEG 13.0 14.40 15.90 1 21.5 139.5 2 X SMDJ14CA PEK DEK 14.0 15.60 17.20 1 23.2 129.3 2 X SMDJ15CA PEM DEM 15.0 16.70 18.50 1 24.4 123.0 2 X SMDJ16CA PEP DEP 16.0 17.80 19.70 1 26.0 115.4 2 X SMDJ17CA PER DER 1 7. 0 18.90 20.90 1 27.6 108.7 2 X SMDJ18CA PET DET 18.0 20.00 22.10 1 29.2 102.7 2 X SMDJ20CA PEV DEV 20.0 22.20 24.50 1 32.4 92.6 2 X SMDJ22CA PEX DEX 22.0 24.40 26.90 1 35.5 84.5 2 X SMDJ24CA PEZ DEZ 24.0 26.70 29.50 1 38.9 77.1 2 X SMDJ26CA PFE DFE 26.0 28.90 31.90 1 42.1 71.3 2 X SMDJ28CA PFG DFG 28.0 31.10 34.40 1 45.4 66.1 2 X SMDJ30CA PFK DFK 30.0 33.30 36.80 1 48.4 62.0 2 X SMDJ33CA PFM DFM 33.0 36.70 40.60 1 53.3 56.3 2 X SMDJ36CA PFP DFP 36.0 40.00 44.20 1 58.1 51.6 2 X SMDJ40CA PFR DFR 40.0 44.40 49.10 1 64.5 46.5 2 X SMDJ43CA PFT DFT 43.0 47.80 52.80 1 69.4 43.2 2 X SMDJ45CA PFV DFV 45.0 50.00 55.30 1 72.7 41.3 2 X SMDJ48CA PFX DFX 48.0 53.30 58.90 1 77.4 38.8 2 X SMDJ51CA PFZ DFZ 51.0 56.70 62.70 1 82.4 36.4 2 X SMDJ54CA RGE DGE 54.0 60.00 66.30 1 87.1 34.4 2 X SMDJ58CA PGG DGG 58.0 64.40 71.20 1 93.6 32.1 2 X SMDJ60CA PGK DGK 60.0 66.70 73.70 1 96.8 31.0 2 X SMDJ64CA PGM DGM 64.0 71.10 78.60 1 103.0 29.1 2 X SMDJ70CA PGP DGP 70.0 77.80 86.00 1 113.0 26.5 2 X SMDJ75CA PGR DGR 75.0 83.30 92.10 1 121.0 24.8 2 X SMDJ78CA PGT DGT 78.0 86.70 95.80 1 126.0 23.8 2 X SMDJ85CA PGV DGV 85.0 94.40 104.00 1 137.0 21.9 2 X SMDJ90CA PGX DGX 90.0 100.00 111.0 0 1 146.0 20.5 2 X
SMDJ100CA PGZ DGZ 100.0 111. 0 0 123.00 1 162.0 18.5 2 X SMDJ110CA PHE DHE 110.0 122.00 135.00 1 177.0 16.9 2 X SMDJ120CA PHG DHG 120.0 133.00 147.00 1 193.0 15.5 2 X SMDJ130CA PHK DHK 130.0 144.00 159.00 1 209.0 14.4 2 X SMDJ150CA PHM DHM 150.0 167.00 185.00 1 243.0 12.3 2 X SMDJ160CA PHP DHP 160.0 178.00 197.00 1 259.0 11. 6 2 X SMDJ170CA PHR DHR 170.0 189.00 209.00 1 275.0 10.9 2 X SMDJ180CA PHT D HT 180.0 198.00 230.40 1 292.0 10.3 2 X SMDJ220CA PKE DKE 220.0 242.00 281.60 1 356.0 8.4 2 X
of 10 volts and less, the IR limit is double.
R
V
R
(Volts)
Breakdown Voltage V
BR
(Volts) @ I
I
T
Maximum
Clamping
Voltage V
@ Ipp
Test
Current
T
(mA)
(V)
Maximum
Peak
Pulse
C
Current Ipp
(A)
Maximum
Reverse
Leakage IR
@ V
R
(µA)
Agency
Approval
Specifications are subject to change without notice.
© 2014 Littelfuse, Inc.
Revised: 01/24/14
Transient Voltage Suppression Diodes
Voltage Transients
Time
Voltage Across TVS
Current Through TVS
Voltage or Current
Surface Mount – 3000W > SMDJ series
I-V Curve Characteristics
Uni-directional
BR
V
Vc
VR
IR
VF
IT
V
Bi-directional
BR
V
Vc
VR
Ipp
P
Peak Pulse Power Dissipation -- Max power dissipation
PPM
V
Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
R
V
Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
BR
V
Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current)
C
I
Reverse Leakage Current -- Current measured at V
R
V
Forward Voltage Drop for Uni-directional
F
Ratings and Characteristic Curves (T
Figure 1 - TVS Transients Clamping Waveform
R
=25°C unless otherwise noted)
A
Figure 2 - Peak Pulse Power Rating
Ipp
IT IR
IR IT
VR
BR
V
V
Vc
Ipp
1000
100
10
1
-Peak Pulse Power (KW)
PPM
P
0.31x0.31" (8.0x8.0mm)
Copper Pad Area
0.1
0.001 0. 01 0.11 td-Pulse Width (ms)
10
continues on next page.
© 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/24/14
Transient Voltage Suppression Diodes
0
20
40
60
80
100
0255075 100 125 150 175
TA-Ambient temperature (ºC)
Peak Pulse Power (P
PP
) or Current (I
PP
)
Derating in Percentage %
P
, Steady Sate Power
Surface Mount – 3000W > SMDJ series
Ratings and Characteristic Curves (T
Figure 3 - Peak Pulse Power or Current Derating Curve
vs Initial Junction Temperature
=25°C unless otherwise noted) (Continued)
A
Figure 4 - Pulse Waveform
150
RSM
Peak Value
100
I
PPM
50
- Peak Pulse Current, % I
PPM
I
t
tr=10µsec
0
d
0
1.0 2.0 3.0 4.0
Half Value
I
I
PPM
( )
TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of I
PPM
2
10/1000µsec. Waveform as defined by R.E.A
t-Time (ms)
Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve
100000
Cj (pF)
10000
1000
100
Uni-directio nal
Bi-directional V
@ VR
Bi-directional
= OV
Uni-directio nal V
@ VR
10
1
1.0 10.0100.0 1000.0
VBR - Reverse Breakdown Voltage (V)
= OV
6.5 6
5.5 5
4.5 4
3.5 3
2.5
Dissipation (W)
2
1.5
M(AV)
1
0.5 0
0255075100 125150 175
TA - Ambient Temperature(ºC)
PPM
Figure 7 - Maximum Non-Repetitive Peak Forward
(A)
- Peak Forward Surge Current
FSM
I
Surge Current Uni-Directional only
350
300
250
200
150
100
50
0
110 100
Number of Cycles at 60 Hz
Specifications are subject to change without notice.
© 2014 Littelfuse, Inc.
Revised: 01/24/14
Transient Voltage Suppression Diodes
DO-214AB (SMC J-Bend)
B
F
G
H
E
C
D
A
Cathode Band
(for Uni-directional products only)
Surface Mount – 3000W > SMDJ series
Soldering Parameters
Reflow Condition Lead–free assembly
Pre Heat
- Temperature Min (T
- Temperature Max (T
) 150°C
s(min)
) 200°C
s(max)
- Time (min to max) (ts) 60 – 180 secs
Average ramp up rate (Liquidus Temp (T
) to peak
L
to TL - Ramp-up Rate 3°C/second max
T
S(max)
Reflow
- Temperature (TL) (Liquidus) 217°C
- Time (min to max) (ts) 60 – 150 seconds
Peak Temperature (TP) 260
Time within 5°C of actual peak Temperature (t
)
p
3°C/second max
+0/-5
°C
20 – 40 seconds
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (T
) 8 minutes Max.
P
Do not exceed 280°C
Physical Specifications
Weight 0.007 ounce, 0.21 grams
Case
Polarity
JEDEC DO214AB. Molded plastic body
over glass passivated junction
Color band denotes positive end
(cathode) except Bidirectional.
t
T
P
Ramp-up Critical Zone
T
L
T
s(max)
T
s(min)
Temperature (T)
25˚C
t
s
Preheat
t 25˚C to Peak
Time (t)
p
t
L
Ramp-down
Environmental Specifications
High Temp. Storage JESD22-A103
HTRB JESD22-A108
Temperature Cycling JESD22-A104
MSL JEDEC-J-STD-020, Level 1
H3TRB JESD22-A101
T
T
to
L
P
© 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/24/14
Terminal
Dimensions
I
Matte Tin-plated leads, Solderable per
JESD22-B102
RSH JESD22-B106
Dimensions
Inches Millimeters
Min Max Min Max
A 0.114 0.126 2.900 3.200
B 0.260 0.280 6.600 7. 11 0
C 0.220 0.245 5.590 6.220
D 0.079 0.103 2.060 2.620
E 0.030 0.060 0.760 1.520
F - 0.008 - 0.203
G 0.305 0.320 7.750 8.130
H 0.006 0.012 0.152 0.305
L
K
J
I 0.129 - 3.300 -
J 0.094 - 2.400 -
K - 0.165 4.200
L 0.094 - 2.400 -
Transient Voltage Suppression Diodes
V
R
VOLTA GE
BI-DIRECTIONAL
5%
V
BR
VOLTA GE TOLERANCE
SERIES
SMDJ XXX CA
0.63
(16.0)
0.315 (8.0)
0.157 (4.0)
0.65
(16.4)
0.80 (20.2)
Arbor Hole Dia.
Optional
7” 7.0 (187)
13” 13.0 (330)
Dimensions are in inches (and millimeters).
Direction of Feed
0.059 DIA
(1.5)
Cover tape
Surface Mount – 3000W > SMDJ series
Part Numbering System Part Marking System
Cathode Band
(for uni-directional products only)
Littelfuse Logo
F
XXX
YMXXX
Marking Code
Trace Code Marking
Y:Year Code M: Month Code XXX: Lot Code
Packaging Options
Part number Component Package Quantity Packaging Option Packaging Specification
SMDJxxxXX DO-214AB 3000 Tape & Reel – 16mm/13” tape EIA STD RS-481
SMDJxxxXX-T7 DO-214AB 500 Tape & Reel – 16mm/7” tape EIA STD RS-481
Tape and Reel Specification
Cathode
Specifications are subject to change without notice.
© 2014 Littelfuse, Inc.
Revised: 01/24/14
Loading...