Page 1
180° HD Camera (ADC-V622) - Installation Guide
https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/180_HD_Camera_(ADC-V622)/180_HD_Camera_(ADC-V622)_-_Installation_Guide
Updated: Thu, 02 Aug 2018 15:57:41 GMT
Pre-installation checklist
• ADC-V622 camera (included)
• AC power adapter (included, required for non-PoE connections)
• Broadband (Cable, DSL, or Fiber Optic) Internet connection
• A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the Wi-Fi Protected Setup
(WPS) feature
• Login and Password for the Alarm.com account to which you will add the camera
Note: There are three local options for connecting the ADC-V622 to the wireless network: Ethernet Mode, Wi-Fi
Protected Setup (WPS) Mode, and Access Point (AP) Mode.
For information on how to install a video device via MobileTech, see Install a video device using the MobileTech app.
Add the camera to an Alarm.com account
1
Page 2
WPS Mode
https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/180_HD_Camera_(ADC-V622)/180_HD_Camera_(ADC-V622)_-_Installation_Guide
Updated: Thu, 02 Aug 2018 15:57:41 GMT
To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting.
1. Connect the camera’s AC power adapter and plug it into a non-switched outlet.
2. Press the Menu button and use the Volume buttons to scroll to the WPS menu option (follow the audio prompts or
look for a flashing blue LED).
3. Press the Menu button to activate WPS Mode. The LED will flash blue.
4. Activate the WPS Mode on the router. The ADC-V622 will begin to connect to the Wi-Fi network. The LED will be
solid green when the connection is complete.
5. Add the device to the account by either selecting the account in MobileTech OR by using a web browser and
entering the following URL: www.alarm.com/addcamera
6. Select the camera from the video device list or type in its MAC address to begin adding the camera. The camera’s
MAC address is located on the back of the camera near the power cable.
7. Follow the on-screen instructions to finish adding the camera. You may configure camera settings using the
Customer Website.
You can now power down the camera and install it in its final location using the included hardware.
AP Mode
To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting.
1. Connect the camera’s AC power adapter and plug it into a non-switched outlet.
2. Press the Menu button and use the Volume buttons to scroll to Access Point mode (follow the audio prompts or
look for a flashing white LED).
3. Press the Menu button to activate Access Point Mode. The LED will flash white.
4. On an Internet enabled device, connect to the Wi-Fi network “ADC-V622 (XX:XX:XX)” where XX:XX:XX is the last
six digits of the ADC-V622’s MAC address, which is located on the back of the device near the power cord.
5. On the same device, open a web browser and enter http://v622install in the URL field. Follow the on-screen
instructions to add the ADC-V622 to the Wi-Fi network. The LED will be solid green when the connection is
complete.
6. Add the device to the account by either selecting the account in MobileTech OR by using a web browser and
entering the following URL: www.alarm.com/addcamera
7. Select the camera from the video device list or type in its MAC address to begin adding the camera. The camera’s
MAC address is located on the back of the camera near the power cable.
8. Follow the on-screen instructions to finish adding the camera. You may configure camera settings using the
Customer Website.
You can now power down the camera and install it in its final location using the included hardware.
Ethernet Mode
Complete these steps prior to installing the camera in its final location.
1. Using an Ethernet cable, connect the camera to the network.
2. Connect the camera’s AC power adapter and plug it into a non-switched outlet (if not using a PoE connection).
2
Page 3
3. Add the device to the account by either selecting the account in MobileTech or by using a web browser and
https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/180_HD_Camera_(ADC-V622)/180_HD_Camera_(ADC-V622)_-_Installation_Guide
Updated: Thu, 02 Aug 2018 15:57:41 GMT
entering the following URL: www.alarm.com/addcamera
4. Select the camera from the video device list or type in its MAC address to begin adding the camera. The camera’s
MAC address is located on the back of the camera near the power cable.
5. Follow the on-screen instructions to finish adding the camera. You may configure camera settings using the
Customer Website.
You can now power down the camera and install it in its final location using the included hardware.
LED reference guide
LED Pattern Status Description
Internet connection
Local network connection
No network connection
Local network and internet
connection
Local network connection only, no
internet
No local network or internet
connection
System booting Camera is booting
To enter WPS mode, push the Menu
button and use the Volume buttons
WPS Mode
to scroll to WPS Mode. See
instructions above to add the
camera to your router and account
using WPS mode.
To enter AP mode, push the WPS
button and release when flashing
AP Mode
white (about 6 seconds). See
instructions above to add the
camera to your router and account
using AP mode.
3
Page 4
LED Pattern Status Description
https://answers.alarm.com/Installation_and_Troubleshooting/Video_Devices/180_HD_Camera_(ADC-V622)/180_HD_Camera_(ADC-V622)_-_Installation_Guide
Updated: Thu, 02 Aug 2018 15:57:41 GMT
To pair with Bluetooth, push the
Bluetooth pairing
Menu button and use the Volume
buttons to scroll to Bluetooth mode.
Caution: This will restore factory-
default settings to the camera. If
already installed, the camera may
need to be removed from the
Alarm.com account and re-added
Factory Reset
after a factory reset.
To perform a factory reset, push the
Menu button and use the Volume
buttons to scroll to the Factory Reset
option. Follow the audio prompts to
initiate Factory Reset.
Troubleshooting
1. If you have issues connecting the camera to the account, power cycle the camera. If using the AC adapter, unplug
the power jack from the camera and then plug it back in to restore power. If using PoE, unplug the Ethernet jack
from the camera and then plug it back in to restore power.
2. If issues persist, try resetting the camera to factory defaults. Press the Menu button and use the Volume buttons
to scroll to the Factory Reset option. Follow the audio prompts to initiate Factory Reset. The camera will reboot
with factory defaults. If the camera was previously installed on an Alarm.com account, it will need to be deleted
before it can be installed again.
Questions?
Visit: https://www.alarm.com/supportcenter
4
Loading...