07-10 TUNDRA
CAMPER TIEDOWNS
3 – Clip the positioning tabs from the ends of the cable
brackets with a pair of dikes or tin snips.
FRONT ANCHORS
Step 1 – Install the support brace to the bracket
as shown below. Snug, but do not tighten,
brace will be positioned later.
Driver
Side
Be sure to connect proper end to bracket This is the end
with the sharper bend and only 1 nut at the end of the
threaded rod section. Use the ½” long fine thread bolt
supplied in the hardware kit..
Step 2 – Remove existing bolts attaching cable clamps to
the frame at the locations shown below.
(Save bolts, they will be reinstalled later)
Drivers side
Passenger
Side
Passenger side
Positioning
Tabs
4. Set tie down bracket in place and install upper bolt. Place
the tie down bracket between the cable bracket and frame
and reinsert the bolt previously removed from this location.
Frame
Drivers Side
Shown
Tie down
Bracket
4.a – On the passenger side, use a 1” bolt, washer, lock washer
& nut through the existing hole in the frame at this location.
5. Ensure that the bracket is sitting snug to the corner and
straight then drill lower
mounting hole through
frame extension
as shown. Note it may
be necessary to clamp
the bracket in place
while drilling.
Use 13/32 drill bit.
Drivers side shown
6. Position the frame end of the support brace between the
frame and the cable bracket removed in step 2 then
reinstall the cable bracket bolt.
8. Adjust support brace to the clearance shown below
then tighten Jam Nut.
NOTE: It may be necessary
to loosen the jam nut on the
threaded portion of the
support brace and lengthen
or shorten the brace until
the hole in the brace lines
up with the hole in the
frame.
Passenger Side Shown
7. Tighten all hardware (do not over tighten and strip).
8. Once the front anchors and support brace are installed
and tightened in place, the support brace can be
adjusted for best fit. Loosen the jam nut and turn the
adjusting nut at the opposite end of the treaded portion
to lengthen or shorten the support brace.
Jam Nut
Bed
Cab
3/16” -1/4”
clearance
Anchor
at closest
Plate
point
This completes the front anchor installation
REAR ANCHORS
NOTE: Rear anchors are installed in the end of the bumper.
here is no precise mounting location since a variety of bumpers
may be installed. The general guidelines are as follows:
1. Mounting location should be as flat & vertical as possible.
2. Be sure no moldings or bumper caps interfere with
the removable coupler.
3. Check back side of selected mounting location to ensure
adequate access for tightening nut.
4. Choose a location approx.2/3 back from the front edge
of the bumper. Center punch and drill a small pilot hole, then
enlarge to
5. Install Anchor Bolt with 2” fender washer, lock washer & nut.
1
/2”.
Adjusting
Nut
Flat edges of Anchor Bolt
must be horizontal.
Mandatory Rear Bumper Brace
This brace is designed to reduce rotational torque
on the rear bumper. The upper end bolts to existing
hole in underside of bed cross member. At the lower
Or bumper end of the brace, the lower edge of the
Bumper is sandwitched between the heavy steel
Plates supplied in this kit. See photos and illustrations..
The hardware kit supplied contains two longer
and two shorter bolts. The longer bolts are used
at the bottom (bumper) end and the shorter bolts
at the upper (under bed) end of the bumper
brace.
Bumper End
Existing hole in
Vertical plate at
End of cross
Member behind
fender well.
Upper end of bumper brace
Attaches here.
Bumper Profile
B
r
e
b
m
e
m
-
s
s
o
r
c
d
e
d
e
b
r
o
t
e
b
d
n
e
em
s
m
i
-
h
s
T
os
r
c
Inside surface
of bumper
Bu
m
p
e
r
Br
a
c
e
Existing
Bumper
Support
Lock
Washer
Bottom
Nut
Flat Washer
Edge of
Bumper
Bolt
Technical support: 801-544-2585
B
u
m
B
p
ra
c
e
r
e
Loading...