Linksys WUSB54GS, WIRELESS-G USB NETWORK, WUSB54G User Manual

A Division of Cisco Systems, Inc.
®
12
The USB Network Adapter is installed and set up using the Setup Wizard that comes on the CD enclosed.
Begin Installation
IMPORTANT: Do not connect the Adapter to Your PC until you are instructed to do so in Step 2 or the Adapter will not install propertly.
Now that the Setup Wizard has prompted you to connect the Adapter, follow the instructions below.
A Connect one end of the
Connect the Adapter
included USB cable to the Adapter’s USB port
Package Contents
• Wireless-G USB Network Adapter with SpeedBooster
• One Setup CD-ROM
• One User Guide on CD-ROM
• USB Cable
• Quick Installation Guide
A To begin, insert the Setup
Wizard CD-ROM into your CD-
ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear.
B To install the Adapter, click
Click Here to Start on the Welcome screen.
C After reading the License
Agreement, click Next to continue the installation and Windows will begin copying the files onto your PC.
D The Setup Wizard will now
prompt you to connect the Adapter to your PC’s USB port.
Proceed to Step 2.
A
C
B Connect the other end of the
cable to one of the USB ports on your computer.
C The Power LED should light up
when the Adapter is plugged in.
D Raise the antenna. Make sure
the antenna points straight up into the air, at a 90º angle from the Adapter. This will ensure optimum wireless operating range and performance.
Once the Adapter is connected, click Next on the Connecting the Adapter screen to proceed.
Proceed to Step 3.
Connecting
the Adapter
How to Connect
2.4
Model No.
Model No.
GHz
802.11g
Wireless
WUSB54GS
Wireless-G
USB Network Adapter
with SpeedBooster
Quick Installation
The Adapter’s
USB Port
3
Set Up the Adapter
The next screen to appear will be the Available Wireless Network screen. From this screen, you can launch one of the three setup methods.
Available Wireless Network
IMPORTANT:There are three ways to set up the Adapter. For Quick Installation,
use this document only if your network appears on the Available Wireless Net­work screen.
SecureEasySetup: If you are utilitizing SecureEasySetup, click the SecureEasySetup button and follow the on screen prompts.
Manual Setup: If you are utilitizing Manual Setup, click the Manual Setup button and follow the on screen prompts.
Setting Up the Adapter with Available Networks
On the Available Wireless Network screen, the available networks are listed in the center table by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your net­work listed, you can click the Refresh button.)
Model No.
If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the shown in Step B.
A
If wireless security has been enabled on this network, you will see a wireless security screen. If your network utilizes WEP (Wired Equivalent Privacy) encryption, the
tion
work utilizes PSK (Pre-Shared Key) encryption, the
for Connection
appear.
WEP Key Needed for Connection
Select
Then, enter a passphrase or WEP key.
Passphrase
in the case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compati­ble with Linksys wireless products only. (Non-Linksys wireless prod­ucts, require a WEP key to be entered.)
WEP Key
match the WEP key of your wire­less network. For 64-bit encryp­tion, enter exactly 10 hexadecimal characters. For 128­bit encryption, enter exactly 26
Congratulations
WEP Key Needed for Connec-
screen will appear. If your net-
PSK Key Needed
screen will
64-bit or 128-bit
- Enter a passphrase
Passphrase
- The WEP key must
field. This is
screen,
.
WEP Key Needed
hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Then, click ceed to Step B.
PSK Needed for Connection
Encryption
algorithm you want to use, AES, from the Encryption down menu.
Passphrase
of 8-63 characters in the
phrase
complex your Passphrase is, the more secure your network will be.
Then, click ceed to Step B.
B
After the Adapter has been con-
figured for the network, the
gratulations
Click nect to your network.
Congratulations! Setup is complete.
NOTE:
After the Adapter is installed, the Wireless Network Monitor screen will open and its icon will appear in your PC’s system tray. Double-click the icon if you want to open the Wireless Network Monitor for find­ing available wireless networks or making additional configuration changes.
Connect and pro-
- Select the type of
TKIP
drop-
- Enter a Passphrase
Pass-
field. The longer and more
Connect and pro-
Con-
screen will appear.
Connect to Network
to con-
or
Wireless Network
Monitor icon
PSK Needed
®
A Division of Cisco Systems, Inc.
For additional information or troubleshooting help, refer to the User Guide on the Setup CD­ROM. You can also call or email for further support.
24-hour Technical Support
800-326-7114 (toll-free from US or Canada)
E-mail Support
support@linksys.com
Website
http://www.linksys.com or http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved.
wusb54gs-qi-50418A BW
Loading...