Linksys HU200 Quick Start Manual
1
Set up the Home Wireless-G USB
Adaptor
2
4
,
GHz
802.11g
Package Contents
• Home Wireless-G USB A daptor
• USB Cable
• Setup CD-ROM with User Guide
• Quick Installation
Home Wireless-G
A Insert the Setup Wizard CD-
ROM into your CD-ROM drive.
The Setup Wizard should run
automatically, and the
Welcome screen should
appear. If it does not, click the
Start button and choose Run.
In the field that appears, enter
D:\setup.exe (if “D” is the letter
of your CD-ROM drive).
B To install the Adaptor, click the
Install button on the Welcome
screen.
C After reading the License
Agreement, click Next.
D Choose a wireless network
mode. Click the Infrastructure
Mode radio button if you want
to connect to a wireless router
or access point. Click the Ad-
Hoc Mode radio button if you
want to connect directly to
another wireless device without
using a wireless router or
access point.
In the SSID field, enter the SSID
or name for your wireless
network. The SSID must be
identical for all devices in the
network. Click Next.
B
C
If you chose Infrastructure
E
Mode, go to Step F now.
If you chose Ad-Hoc Mode,
select the channel that your
network uses. For the Network
Mode, select Mixed Mode to
allow both Wireless-G and
Wireless-B computers on the
network, or select G-Only
Mode to allow only Wireless-G
computers. Then click Next.
F If your network doesn’t use any
security method, select
Disabled and click Next.
Proceed to Step H.
Select the security method you
want to use: WEP or PSK. (WEP
stands for Wired Equivalent
Privacy, and PSK stands for PreShared Key.) Then click Next
and proceed to Step G.
NOTE: If your network is using WPA-
Personal or WPA-PSK security, then
select PSK.
E
F
USB Adaptor
Wireless
Model No.
HU200
Quick Installation
D
2
Connect the Home Wireless-G USB
Adaptor
G Proceed to the appropriate
instructions for your security
method.
1WEP
a Select 64-bit or 128-bit from
the drop-down menu.
b Enter your Passphrase in the
Passphrase field, and the WEP
key will be automatically
generated.
To manually enter the WEP key,
leave the Passphrase field
blank and enter the WEP key in
the WEP Key field.
c Click Next, and go to Step H.
2PSK
WEP
H The Setup Wizard will ask you to
review your settings before it
starts to copy files. Click Next to
save these settings, or click
Back to change any settings.
I After the software has been
successfully installed, the
Congratulations screen will
appear. Click Exit.
H
I
A Connect one end of the
included USB cable to the USB
port of the Adaptor.
B Connect the other end to a
USB port on your PC. When the
Adaptor is plugged in, the
Power LED should light up.
C Raise the antenna. It should
point straight up into the air, at
a 90º angle from the Adaptor.
D After the Adaptor is installed,
the Wireless Network Monitor
icon will appear in the system
tray at the bottom right-hand
corner of your screen.
NOTE: Double-click the icon if you want
to check the link information, search for
available wireless networks, or make
additional configuration changes.
A
C
D
a Select the encryption method
you want to use, TKIP or AES,
from the drop-down menu.
b Enter your Passphrase or Pre-
Shared Key in the Passphrase
field.
c Then click Next and proceed
to Step H.
PSK
Congratulations! The installation of
the Home Wireless-G USB Adaptor is
complete.
For additional information or troubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
Registration
http://www.linksys.com/registration
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its a ffili ates i n the U.S.
and certain other countries. Copyright © 2005
Cisco Systems, Inc. All rights reserved.
HU200-UK-QI-50309A JL
Loading...