Quick Installation Guide
My Devices
Local Device
WA850RE
XX-XX-XX-XX-XX-XX
Connections are available
Wireless Network Connection
Range Extender
TL-WA850RE
1
Power On
Plug the extender into a power outlet next to your router. Wait until its
Power LED turns solid on.
Next to
©2019 TP-Link
7106508258 REV6.1.0
Need setup videos?
Scan the QR code, or visit
https://www.tp-link.com/download/TL-WA850RE.html
2
Set Up
Method 1: Via the WPS Button
1. Press the WPS button on your router.
The WPS button might
look like one of these:
2. Within 2 minutes, press the WPS button on the
extender for 1 second. The RE LED should change
from blinking to solid on, indicating successful
connection.
Note: If the LED does not turn solid on, try again or use Method 2
or 3.
Method 2: Via the Tether App
1. Get the up-to-date Tether app.
or
Scan for Tether Tether
2. Connect your smartphone to the extender’s
network TP-Link_Extender.
Wi-Fi
< Settings
Wi-Fi
CHOOSE A NETWORK...
3. Launch the Tether app, and select your extender.
Create a password to log in.
Solid On
Method 3: Via a Web Browser
1. Connect your computer or smartphone to the
extender’s network TP-Link_Extender. If you are
using a computer, unplug the Ethernet cable if any.
TP-Link_Extender
√
Connect automatically Connect
2. Launch a web browser, and enter
http://tplinkrepeater.net or http://192.168.0.254
in the address bar. Create a password to log in.
Note: If the login window does not appear, refer to FAQ > Q1.
http://tplinkrepeater.net
Blinking Solid On
3. The extender uses your router’s network name
with _EXT at the end, and shares the same
password as your router.
Note: If you want to change the extended network name, refer to
Access Extender Settings on the back page.
3
Relocate
Extended Network Name:
Router’s network name with
Password:
Same as your router
_EXT
at the end
4. Follow app instructions to complete the setup.
The RE LED should turn solid on, indicating
successful connection to your router.
Note: If the LED does not turn solid on, refer to FAQ > Q2.
Solid On
1. Plug in the extender about halfway between your router and the Wi-Fi dead
zone. The location you choose must be within the range of your router.
2. Wait for about 2 minutes until 3 or more LEDs light up. If not, relocate the
extender closer to the router to achieve better signal quality.
Tip: For more intuitive location assistant, access extender settings via the Tether app and go to Tools > Location Assistant.
Create Password
Low Middle High
Conrm Password
Start
3. Follow web instructions to complete the setup.
The RE LED should turn solid on, indicating
successful connection to your router.
Note: If the LED does not turn solid on, refer to FAQ > Q2.
Solid On
Best
5
4
3
Good
≥ 3 LEDs light up
2
1
Router Devices
Halfway
Connect your devices to the extender wirelessly or via an Ethernet cable, then
enjoy the internet.
Tip: You can also set up the extender in Access Point mode to transform your existing wired network
to a wireless one. For details, refer to the user guide at https://www.tp-link.com/support.
Enjoy!
Access Extender Settings
After setup, you can access extender settings via any of the methods below.
You can reselect host network, change extended network settings and more.
Note: If your extender and router use the same network name, Method 1 is recommended.
Method 1: Via the Tether App
Tether
LED Explanation
5
4
3
2
1
1. Connect your smartphone to the extender‘s or router’s network.
2. Launch the Tether app, select your extender, and log in.
3. View or change extender settings as needed.
Method 2: Via a Web Browser
http://tplinkrepeater.net
1. Connect your computer or smartphone to the extender’s network. If you
are using a computer, unplug the Ethernet cable if any.
2. Launch a web browser, enter http://tplinkrepeater.net in the address bar,
and log in.
Note: If the login window does not appear, refer to FAQ > Q1.
3. View or change extender settings as needed.
http://tplinkrepeater.net
LED Status Indication (For Range Extender Mode)
The extender is connected or not connected to
your router’s wireless network
.
WPS connection is in progress.
The extender’s wireless function is enabled or
disabled.
The extender is on or o.
The system is starting up or rmware upgrade is in
progress.
RE
Wireless
Power
On/O
Blinking
On/O
On/O
Blinking
Indicates the Wi-Fi connection between the
(Signal
Strength)
Ethernet
On/O
On/O
extender and the router. More lit LEDs indicates a
better signal strength.
The Ethernet port is connected or not connected
to a powered-on device.
Q1. What should I do if I cannot access the extender’s web
management page?
Make sure your computer or smartphone has connected to the extender’s
network, and not that of your router. If your router and extender share the same
network name, connect your computer to the extender via an Ethernet cable, or
use the Tether app.
If you are using a computer, make sure it is set to obtain an IP address and DNS
server address automatically.
Verify that http://tplinkrepeater.net or http://192.168.0.254 is correctly entered
in the web browser and press Enter. Note that http://192.168.0.254 applies only
for extenders with factory default settings.
Use another web browser and try again.
Reboot or reset the extender and try again.
If you are still having problems, contact our technical support.
Q2. What should I do if the RE LED doesn’t turn solid on after
completing setup via the Tether app or web browser?
You may have entered incorrect Wi-Fi password for your host router during the
conguration. Check the password and try again.
Make sure the extender is close to your router, preferably within 16 feet, and
away from large electrical appliances.
If you have enabled wireless MAC ltering, wireless access control, or access
control list (ACL) on your router, disable them rst, then follow any method on the
front page to complete the conguration.
Try setting up via the WPS button.
Reset the extender and go through the conguration again.
If you are still having problems, contact our technical support.
Q3. How do I reset the extender?
With the extender powered on, use a pin to press the RESET button for 1
second. The extender will reboot.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use the device where wireless devices are not allowed.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot
guarantee that no accidents or damage will occur due to improper use of the device.
Please use this product with care and operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
For technical support, the user guide and other information, please
visit https://www.tp-link.com/support, or simply scan the QR code.