Linear T7521S, T7523S, T7543S, T7511S, T5011S Specsheet

...

Product No. See table below

DOOR TYPE

Fiberglass

Steel-24 Ga. Steel-22 Ga. Aluminum

Wood Steel-20 Ga. Steel-24 Ga. insulated

Steel-16 Ga. Steel-20 Ga. insulated

Steel-16 Ga. insulated

Operator size to use ➜

MODEL HP

T3311 T3321 230V 1P T3323 230V 3P T3343 460V 3P T5011 T5021 230V 1P T5023 230V 3P T5043 460V 3P T7511 T7521 230V 1P T7523 230V 3P T7543 460V 3P

MAXIMUM DOOR

AREA (SQ. FEET)

310 420 570

285 350 520

260 320 480

175 250 380

125 200 280

1/3 HP 1/2 HP 3/4 HP

VOLTAGE &

PHASE

115V 1P

1/3

115V 1P

1/2

115V 1P

3/4

Commercial Door Operators

T SERIES

Heavy-Duty Drawbar Commercial Door Operator

Heavy-duty drawbar garage door operator for standard lift sectional doors.

RATINGS

• Maximum duty cycle: 25 cycles per hour, 100 cycles per day

• Maximum door height: 22-1/2 feet

• Shipping weight: 135 lbs.

FEATURES

• All welded steel frame

• 5L V-Belt drive from motor to clutch shaft

• #65 Roller chain on 1/3 and 1/2 HP

• #41 Roller chain on 3/4 HP

• Quick disconnect door arm for manual door operation

• Solenoid brake standard on 3/4 HP (optional on 1/2 & 3/4 HP)

• Solid state or electromechanical control circuit

• Motor overload protection

• Wired to accept reversing devices

• Internally adjustable limit switches

• High starting torque, continuous duty motor

• 24-Volt control circuit with OPEN, CLOSE and STOP push button station

• OPEN button (and single button) will automatically override down travel and reverse door to the full open position

• External terminal for single-button (residential type) radio control

RAIL OPTIONS

• Rail for up to 14’ 6” high doors

• Rail for up to 16’ 6” high doors

• Rail for up to 18’ 6” high doors

• Rail for up to 20’ 6” high doors

• Rail for up to 22’ 6” high doors

FACTORY OPTIONS

• Solid state controller: Add S to model number

• Solenoid brake: Add -BK to model number

• MVP-MR 3-channel open-close-stop modular receiver installed (on solid state controller model only): P/N 2650-159

• MVP-RE-24V-8W-FC 1-door open-close-stop receiver (for electromechanical controller model only): P/N 190-110554

WARRANTY

www.linearcorp.com Speciﬁ cations subject to change without notice800.421.1587

• 2 years

Solid State Control

T Series

DRAWBAR OPERATOR

Heavy-Duty Commercial Operator

CUSTOMER PROJECT ARCHITECT/ENGINEER CONTRACTOR DRAWING NUMBER DATE SHEET OF

ORDERING INFORMATION:

SUPPLY __________ LINEAR OPERATOR(S) MODEL

WITH A MOTOR RATING OF __________HP, __________VOLTS, _____PHASE, _____HERTZ

FOR A __________ WIDE X __________ HIGH DOOR(S) WITH ______________________________________

SUPPLY _______ OPEN-CLOSE-STOP CONTROL STATION(S) IN NEMA _______ ENCLOSURE PER OPERATOR

______________ DRIVE SPROCKET ______________ DOOR SPROCKET

T __ __ __ __ S___________________________________

AUXILIARY AND OPTIONAL EQUIPMENT AS SPECIFIED BELOW OR ON ATTACHED SHEET:

ARCHITECTURAL SPECIFICATIONS (DRAWBAR):

Electric door operator(s) shall be Solid State Control Model T of the trolley (drawbar) type, manufactured by Linear LLC and Underwriters Laboratory (UL) listed. Horsepower, voltage and phase will be as required to properly operate the door. Operators will be equipped with twostage speed reduction (V-belt primary and roller chain and sprocket secondary) and an adjustable slip clutch. The operator will have a double angle (nominal 11 gage, 2” X 2”) trolley track of sufficient length to accommodate the height of the installed door. The trolley will be driven with roller chain. The door arm will be provided with a trolley disconnect for manual door operation. The operator will be equipped with an integral limit system that provides accurate settings to control the open and close positions of the door and will not be affected by manual door operation or motor removal. The motor and operator will be protected against overload by a thermal protector. The operator will have a 24VAC secondary solid state control circuit with advanced switch selectable features, motor load delivered via high amperage, inductive load rated relays. The operator will have provisions for connecting open-close-stop pushbutton stations, radio controls, and external obstruction sensing (reversing) systems. The door speed will be approximately 11-12 inches per second.

NOTES: REFER TO PRODUCT DATA SHEET FOR GENERAL INFORMATION REFER TO DRAWING____________FOR WIRING DIAGRAM

LINEAR LLC Phone 800-421-1587 1950 Camino Vida Roble Ste. 150 Fax 800-468-1340 Carlsbad, CA 92009 Website www.linearcorp.com