Linear MCT-11 User Manual

MCT-11

(760) 438-7000

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

BE SURE THE DOOR OR GATE AREA IS CLEAR!

ACTIVATE THE TRANSMTTER TO TEST THE RECEIVER AND OPERATOR

THE VISOR CLIP CAN BE INSTALLED FO

R HORIZONTAL OR VERTICAL MOUNTIN

SLIDE THE VISOR CLIP INTO ONE OF THE SLOTS ON THE REAR OF THE TRANSMITTE

NOTE: THE CIRCUIT BOARD WILL FIT ONLY ONE WAY INTO THE CASE. ALIGN THE PLASTIC POST IN THE CASE WITH THE HOLE IN THE CIRCUIT BOAR

TWIST DIME IN SLOT TO OPEN CASE

LIFT OFF THE TOP OF THE CASE

CAREFULLY REMOVE TH

CIRCUIT BOAR

REMOVE OLD BATTERIES AND DISPOSE OF THEM PROPERLY

INSERT TWO NEW TYPE 2032 BATTERIES

PLUS SIDE UP

THEN

REASSEMBLE UNIT

CLOSE LIMI

OPEN LIMI

DOW

DOWN

TO PROGRAM THE CODE, WITH THE RECEIVER IN LEARN MODE, PRESS THE TRANSMITTER BUTTO

TO SEND A SIGNAL TO THE RECEIVER

1-BUTTON DIGITAL TRANSMITTER

Operation Instructions

The MCT-11 MegaCode® digital transmitter is a wireless radio

DESCRIPTION

control designed for use with automatic garage and gate operators.

MegaCode® transmitters and receivers do not contain a typical “coding switch”. Each transmitter is permanently coded at the factory. The transmitter sends a unique code when the button is pressed. The receiver is programmed by “learning” a transmitter’s unique digital code. The receiver will activate only from the “memorized” transmitters.

The transmitter is powered by two Type 2032 “coin-cell” batteries. They should last 3 years with normal use. The red indicator on the face of the transmitter will glow when the unit is activated. If the indicator lights dimly, or not at all when transmitting, the batteries need to be replaced. To conserve battery life, an internal timer limits the transmission duration to 10 seconds if the transmitter button is held down.

Refer to the instructions provided with the receiver to set it into

PROGRAM RECEIVER & TEST TRANSMITTER

“learn” mode. With the receiver ready to learn, press the transmitter button to program the transmitter into the receiver’s memory.

After programming, test the transmitter from various locations.

sure the door or gate areas are clear. Activate the transmitter

and verify that the receiver triggers the operator.

VISOR CLIP INSTALLATION REPLACING THE BATTERIES LINEAR LIMITED WARRANTY

This product is warranted to the consumer against defects in mater ial and workmanship for one year from the date of purchase. This warranty applies to ﬁrst retail buyers of new devices. Warrantor will repair, or at its option, replace, any device it ﬁnds that requires service under this warranty, and will return the repaired or replaced device to the consumer at the warrantor’s cost. For warranty service and shipping instructions contact warrantor at the address shown below. Devices must be sent to warrantor for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send copy with equipment should repair be required. This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

Linear radio controls provide a reliable communications link and ﬁll an impor tant need in portable wireless signaling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

• Changes or modiﬁcations to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

• This device complies with FCC Part 15 and Industry Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT !!!