Linear LDCO850 Homeowner's Manual
LDCO850
Smart Wi-Fi Garage Door Opener
DC motor with LED lighting and belt- or chain-drive rail
Homeowner’s Manual
Installer’s Contact Information:
WARNING
To reduce the risk of injury to persons – Use this
opener only with sectional residential overhead doors.
Do not use on one piece or swing doors.
• Please read this manual and included safety information carefully.
• After the opener is installed and working properly, use your smart phone to
download, and activate the Linear PRO Access Smart Control app (page 10).
Important Safety Information ............................... page 1
Using the Garage Door Operator ........................ page 2
Manual Disconnect .............................................. page 3
Testing the Safety Beam ..................................... page 4
Adjusting the Open and Close Limits .................. page 5
Automatic Door Force Setup ............................... page 6
Safety Reversal System Test ............................... page 6
Programming Remote Controls ........................... page 7
Programming Keypad Codes .............................. page 8
Setting Up the Wall Station ................................. page 9
Maintenance ...................................................... page 11
Troubleshooting ................................................. page 13
Warranty ............................................................ page 14
Printed in China for GTO Access Systems, LLC.
Copyright© 2017 GTO Access Systems, LLC
Document Number: 10014541 REV-D (07-11-17)
IMPORTANT SAFETY INFORMATION
Important Safety Information will follow
the words CAUTION and WARNING
which are used to emphasize potentially
hazardous situations.
CAUTION
This type of warning note is
used to indicate the possibility
of damage to the garage door or
garage door opener.
WARNING
This type of warning note is used
to indicate possible mechanical
hazards that may cause serious
injuries or death.
WARNING
Children operating or playing with a garage door opener can injure themselves or others.
The garage door could cause serious injury or death. Do not allow children to operate the
remote control(s) or the wall station. Install the wall station out of reach of children and
away from all moving parts of the door. The door must be clearly visible from the wall
station. A moving garage door could injure someone under it. Only activate the door when
it is properly adjusted, when it can be seen clearly, and when there are no obstructions to
the door travel.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
Garage doors are large and heavy objects that move with the help of springs under high tension and electric
motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and
the safety of others depends on you reading the information in this installation manual. If you have questions or
do not understand the information presented, call Linear PRO Access Technical Support at 1-800-543-1236.
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH TO PERSONS, REVIEW THESE INSTALLATION
SAFETY STEPS BEFORE PROCEEDING
1 READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2 Never let children operate or play with door controls. Keep the remote control away from children.
3 Always keep the moving door in sight and away from people and objects until it is completely closed.
NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4 NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
5 Test the door monthly. The garage door MUST reverse on contact with a 1-1/2 inch high object (ir 2 x 4
board laid at) on the oor. After adjusting either the force or the limit of travel, retest the door opener.
Failure to adjust the opener properly increases the risk of severe injury or death.
6 For products having an emergency release, when possible, use the emergency release only when door
is closed. Use caution when using this release with the door open. Weak or broken springs are capable
of increasing the rate of door closure and increasing the risk of severe injury or death.
7 KEEP GARAGE DOORS PROPERLY BALANCED. See user’s manual. An improperly balanced door
increases the risk of severe injury or death. Have a qualied service person make repairs to cables,
spring assemblies, and other hardware.
8 For operator systems equipped with an unattended operation feature, the following statement shall be
included: “This operator system is equipped with and unattended operation feature. The door could
move unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR”.
9
SAVE THESE INSTRUCTIONS.
1
REMOTE CONTROL
WIRELESS KEYPAD
WALL STATION
PRESS THE
UP/DOWN ARROW
PRESS THE BUTTON
PROGRAMMED FOR
SPECIFIC DOOR
ENTER AN ACCESS
CODE AND PRESS
THE KEY
WHEN OPENER IS ACTIVATED LIGHT WILL
REMAIN ON FOR ABOUT 5 MINUTES
LIGHT FLASHES FOUR (4) TIMES AND
OPENER STOPS IF DOOR TRAVEL
IS OBSTRUCTED WHILE OPENING
LIGHT FLASHES THREE (3) TIMES,
OPENER STOPS AND OPENS IF
PHOTO BEAM IS INTERRUPTED OR
DOOR TRAVEL IS OBSTRUCTED
WHILE CLOSING
USING THE GARAGE DOOR OPERATOR
Opening the Door
1 With the door in view, press the wall station’s
UP/DOWN ARROW button, the button assigned
to the opener on the remote control, or enter a
valid access code and press on a wireless
keypad.
2 When the opener is activated, the opener’s light
will turn on and the door will begin to open.
3 The door will open until the open limit is reached.
If an obstacle is encountered while the door is
opening, opener’s light ashes four times and the
door will stop.
4 The opener’s light will stay on for about ve
minutes after the door stops.
Closing the Door
1 With the door in view, press the wall station’s
button or the button assigned to the opener on
the remote control, or enter a valid access code
and press on a wireless keypad.
2 When the opener is activated, the opener’s light
will turn on and the door will begin to close.
3 The door will close until the close limit is
reached. If an obstacle is encountered, the door
will stop and reverse to open and the opener’s
light ash four times. If the safety beam is
interrupted during closing, the door will stop and
reverse to open and the opener’s light will ash
three times.
4 The opener’s light will stay on for about ve
minutes after the door stops.
Stopping the Door Mid-travel
1 The door can be stopped immediately at any
time by pressing the wall station’s UP/DOWN
ARROW button, the remote control’s push
button, or press the button on a wireless
keypad (if the wireless keypad was used to start
the door).
2 The next time the opener is activated, the door
will move in the opposite direction.
2
Vacation Lock for Additional Security
1 Open the wall station’s cover to access the Programming
Buttons. Press the LOCK ( ) button to prevent remote
controls from opening the door after the door is completely
closed. When the Vacation Lock is activated, the remote
controls can close the door, but not open it. The door can
still be opened or closed by using the wall station’s UP/
DOWN ARROW pushbutton.
NOTE: To signal that the vacation switch is locked, the
opener’s light will ash and the alarm will sound ve times if
a remote control is activated in an attempt to open the door.
2 Press the wall station’s LOCK ( ) button again to unlock
and return the operator to normal operation.
Wall Station Reset
If you change your home router or password you will need to
RESET your Wall Station.
1 To do a Wall Station RESET press the WiFi Link ( ) button
for 10 seconds, the RED LED blinks and then turns solid
RED. The Wall Station is now ready to re-link to a new or
updated home router.
2 To re-boot the Wall Station for software updates, press the
RESET ( ) button.
FLIP THE LARGE COVER UP TO ACCESS
PROGRAMMING BUTTONS.
LOCK RESET
WiFi LINK
PRESS THE LIGHT BUTTON TO TURN
THE LIGHT ON OR OFF.
THE LIGHT WILL STAY ON UNTIL THE
LIGHT BUTTON IS PRESSED OR THE
OPENER IS CYCLED.
Controlling the Opener’s Light
1 The opener’s light can be turned ON by pushing the wall
station’s on/off ( ) button. The light will stay on until the
button is pressed again or the opener is cycled.
2 To DECREASE the light brightness press the dimmer ( – )
button.
3 To INCREASE the light brightness press the brighter ( + )
button.
MANUAL DISCONNECT
Disconnecting the Door from the Opener
1 With the door in any position (preferably
closed), carefully pull the red release
handle. USE CAUTION IF THE DOOR IS
OPEN, THE DOOR MAY DROP.
2 The disconnected door can be opened or
closed manually.
3 To reconnect the opener, ip the release
lever up. Raise or lower the door manually
until the opener reconnects.
NOTICE
IF DOOR BECOMES OBSTRUCTED
PULL DOWN ON HANDLE
DIMMER ON/OFF BRIGHTER
PULL TO RELEASE
THE TROLLEY
FLIP UP TO
RECONNECT
THE TROLLEY
NOTICE
IF DOOR BECOMES OBSTRUCTED
PULL DOWN ON HANDLE
3
TESTING THE SAFETY BEAM
WARNING
• Photo beams MUST be installed on the garage door to prevent serious injury or death.
• This required safety reversing sensor MUST NOT be disabled at any time.
• Photo beams should be installed no higher than 6” above the oor.
The safety beam has two components, a sender and a receiver. The sender
produces a narrow infrared beam that travels across the bottom of the
RedGreen
door opening to the infrared receiver. If an object blocks the infrared beam
while the door is closing, the door will stop, then reverse and fully open
(the opener’s light will ash three times).
As a safety feature, the opener will ignore signals from all remote controls
SENDER RECEIVER
Green
if the door is open and the infrared safety beam is blocked or out of
alignment. In this case, the door can be forced closed by pressing and holding the wall station’s up/down
arrow pushbutton (be sure the door area is in clear view).
Safety Beam Test
1 Check that the opener has power. The green lights on the
sender and receiver should be lit.
2 If the receiver’s green light is on, but the red light is off, the
receiver has power but is not detecting the infrared beam
from the sender. The red light might ash when the beam
SENDING UNIT
RECEIVING UNIT
RED LED
STAYS LIT
WHEN BEAMS
ARE ALIGNED
GREEN LED LIT
WHEN POWER IS ON
is partially detected. This can be caused by mis-alignment
or something blocking the beam. Adjust the safety beam
sender and receiver while watching the receiver’s red light
(stay out of the beam while aligning it). When the red light
stays on, rotate the sender towards the ceiling and stop when
the red light on the receiver begins to icker. Rotate the sender
back towards a horizontal position with the oor and stop as
soon as the red light on the receiver lights solid. The beam is
now properly aligned.
RED FLASHING
SAFETY BEAM INDICATOR TABLE
GREEN ON
GREEN OFF
RED ON
RED OFF
POWER ON
POWER OFF
BEAM OK - NO BLOCKAGE
BEAM BLOCKED OR MIS-ALIGNED
BEAM ALIGNED POORLY
NOTE: If the receiver’s red light remains off, check for: 1) Dirt on the receiver’s lens, 2) Sunlight shining into
the receiver’s lens, 3) A short in the safety beam wiring (from staples or at the opener terminals).
3 • Press the remote control button to open the garage door.
• Place a box in the path of the safety beams.
• Press the remote control button to close the door. The door will not
move and the opener‘s lights will ash and beep.
4 The garage door operator will not close if the beams are misaligned or
obstructed.
NOTE: If the door remains idle for 5 minutes, the beam light will turn
off to save power. The beam power turns on for 5 minutes when door
moves down to the fully closed position. The beam power can be restored for 5 minutes by pressing the
light button.
IMPORTANT: If the garage door closes when the safety beam is obstructed, call a professional garage door
technician.
4
Loading...