Linear AUH10023, AUH10043, AUH3311, AUH3321, AUH3323 Specsheet

...

Commercial Door Operators

AUH SERIES

Heavy-Duty Jackshaft Commercial Door Operator

Heavy-duty jackshaft garage door operator for rolling steel curtain doors.

Product No. See table below

DOOR TYPE

Fiberglass

Steel-24 Ga. Steel-22 Ga. Aluminum

Wood Steel-20 Ga. Steel-24 Ga. insulated

Steel-16 Ga. Steel-20 Ga. insulated

Steel-16 Ga. insulated

Operator size to use ➜

MODEL HP

AUH3311 AUH3321 230V 1P AUH3323 230V 3P AUH3343 460V 3P AUH5011 AUH5021 230V 1P AUH5023 230V 3P AUH5043 460V 3P AUH7511 AUH7521 230V 1P AUH7523 230V 3P

AUH7543 460V 3P AUH10023 AUH10043 460V 3P

Equipped with

Chain Hoist and

Floor Level Disconnect

MAXIMUM DOOR AREA

(SQ. FEET)

330 420 570 700

310 375 540 625

280 340 500 560

195 275 400 420

145 225 300 310

1/3 HP 1/2 HP 3/4 HP 1 HP

VOLTAGE &

PHASE

115V 1P

1/3

115V 1P

1/2

115V 1P

3/4

230V 3P

RATINGS

• Maximum duty cycle: 35 cycles per hour, 100+ cycles per day

• Maximum door height: 24 feet

• Shipping weight: 110 lbs.

FEATURES

• Floor level disconnect and chain hoist with interlock for manual door operation

• Manual operation will not affect limit switch settings

• All Steel frame

• Adjustable friction clutch

• 3/4” Shafting and 1” Jackshaft

• Pillow block bearings on output shaft

• #41 Chain and Sprocket, 1/3 & 1/2 HP

• #40 Chain and Sprocket, 3/4 & 1 HP

• Solid state (up to 3/4 HP) or

electromechanical control circuit

• Solenoid brake standard

• Motor overload protection

• Wired to accept reversing devices

• Internally adjustable limit switches

• High starting torque, continuous duty motor

• 24-Volt control circuit with OPEN, CLOSE and STOP push button station

• OPEN button (and single button) will automatically override down travel and reverse door to the full open position

• External terminals for single button (residential type) radio control

FACTORY OPTIONS

• Solid state controller: Add S to model number

• MVP-MR 3-channel open-close-stop modular receiver installed (on solid state controller model only): P/N 2650-159

• MVP-RE-24V-8W-FC 1-door open-close-stop receiver (for electromechanical controller model only): P/N 190-110554

WARRANTY

• 2 years

www.linearcorp.com Speciﬁ cations subject to change without notice800.421.1587

Solid State Control

AUH Series

JACKSHAFT OPERATOR WITH CHAIN HOIST

Heavy-Duty Commercial Operator

CUSTOMER PROJECT ARCHITECT/ENGINEER CONTRACTOR DRAWING NUMBER DATE SHEET OF

ORDERING INFORMATION:

SUPPLY __________ LINEAR OPERATOR(S) MODEL A U

WITH A MOTOR RATING OF __________HP, __________VOLTS, _____PHASE, _____HERTZ

FOR A __________ WIDE X __________ HIGH DOOR(S) WITH ______________________________________

SUPPLY _______ OPEN-CLOSE-STOP CONTROL STATION(S) IN NEMA _______ ENCLOSURE PER OPERATOR

______________ DRIVE SPROCKET ______________ DOOR SPROCKET

H __ __ __ __ S ______________________

AUXILIARY AND OPTIONAL EQUIPMENT AS SPECIFIED BELOW OR ON ATTACHED SHEET:

ARCHITECTURAL SPECIFICATIONS (HOIST):

Electric door operator(s) shall be Solid State Control Model AUH of the jackshaft hoist type, manufactured by Linear LLC and Underwriters Laboratory (UL) listed. Horsepower, voltage and phase will be as required to properly operate the door. Operators will be equipped with twostage speed reduction (V-belt primary and roller chain and sprocket secondary) and an adjustable slip clutch. A floor level disconnect device with chain hoist will be provided for mechanical disengagement to allow for manual door operation. An electrical interlock switch will cut power to the control circuit when in manual operation. The operator will be equipped with an integral limit system that provides accurate settings to control the open and close positions of the door and will not be affected by manual door operation or motor removal. The motor and operator will be protected against overload by a thermal protector and will be equipped with a solenoid operated brake with internal expanding 360 degree brake shoe. The operator will have a 24VAC secondary solid state control circuit with advanced switch selectable features, motor load delivered via high amperage, inductive load rated relays. The operator will have provisions for connecting open-close-stop pushbutton stations, radio controls, and external obstruction sensing (reversing) systems. Operator will drive the door at a speed of approximately 11 inches per second.

NOTES: REFER TO PRODUCT DATA SHEET FOR GENERAL INFORMATION REFER TO DRAWING____________FOR WIRING DIAGRAM

LINEAR LLC Phone 800-421-1587 1950 Camino Vida Roble Ste. 150 Fax 800-468-1340 Carlsbad, CA 92008 Website www.linearcorp.com