Lincoln Electric PCT125M, PCT125 User Manual

IM543

3

4

C

E

I

I

E

C

6

0

9

7

4

-

7

A

-

1

4

1

RETURN TO MAIN MENU

Magnum PCT125/PCT125M

Safety Depends on You

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ­ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON­TAINED THROUGHOUT. And,
most importantly, think before you
act and be careful.

™

July, 2004

3

OPERATOR’S MANUAL

Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com

Copyright © 2004 Lincoln Global Inc.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

i

SAFETY

i

WARNING

PLASMA CUTTING or GOUGING can be hazardous.

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN
AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information it is strongly recommended that you pur­chase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040,
Miami, Florida 33135 or CSA Standard W117.2.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR PROCEDURES ARE PER­FORMED ONLY BY QUALIFIED INDIVIDUALS.

ELECTRIC SHOCK can kill.

1.a. The electrode and work (or ground) circuits
are electrically “hot” when the power source is on.
Do not touch these “hot” parts with your bare skin
or wet clothing. Wear dry, hole-free gloves to insu­late hands.

1.b. When the power source is operating voltages
in excess of 250 volts are produced. This creates the poten­tial for serious electrical shock - potentially even fatal.

1.c. Insulate yourself from work and ground using dry insulation.
When cutting or gouging in damp locations, on metal frame­work such as floors, gratings or scaffolds and when in posi­tions such as sitting or lying, make certain the insulation is
large enough to cover your full area of physical contact with
work and ground.

1.d. Always be sure the work cable makes a good electrical con­nection with the metal being cut or gouged. The connection
should be as close as possible to the area being cut or
gouged.

1.e. Ground the work or metal to be cut or gouged to a good elec­trical (earth) ground.

1.f. Maintain the plasma torch, cable and work clamp in good, safe
operating condition. Replace damaged insulation.

1.g. Never dip the torch in water for cooling or plasma cut or gouge
in or under water.

1.h. When working above floor level, protect yourself from a fall
should you get a shock.

1.i. Operate the pilot arc with caution. The pilot arc is capable of
burning the operator, others or even piercing safety clothing.

1.j. Also see Items 4c and 6.

ARC RAYS can burn.

2.a. Use safety glasses and a shield with the prop­er filter and cover plates to protect your eyes from
sparks and the rays of the arc when performing or
observing plasma arc cutting or gouging.
Glasses,headshield and filter lens should conform
to ANSI Z87. I standards.

2.b. Use suitable clothing including gloves made from durable
flame-resistant material to protect your skin and that of your
helpers from the arc rays.

2.c. Protect other nearby personnel with suitable non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.

keep fumes and gases away from the breathing zone. When

cutting or gouging on lead or cadmium plated steel and
other metals or coatings which produce highly toxic
fumes keep exposure as low as possible and below
Threshold Limit Values (TLV) using local exhaust or
mechanical ventilation. In confined spaces or in some
circumstances, outdoors, a respirator may be required.
Additional precautions are also required when welding
on galvanized steel.

3.b. Do not use plasma arc cutting or gouging in locations near
chlorinated hydrocarbon vapors coming from degreasing,
cleaning or spraying operations. The heat and rays of the arc
can react with solvent vapors to form phosgene, a highly toxic
gas, and other irritating products.

3.c. Gases used for plasma cutting and gouging can displace air
and cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.

3.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your employ­er’s safety practices.

gouging can easily go through small cracks and openings to
adjacent areas. Avoid cutting or gouging near hydraulic lines.
Have a fire extinguisher readily available.

4.b. Where compressed gases are to be used at the job site, spe­cial precautions should be used to prevent hazardous situa­tions. Refer to “Safety in Welding and Cutting” (ANSI Standard
Z49.1) and the operating information for the equipment being
used.

4.c. When not cutting or gouging, make certain no part of the elec­trode circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.

4.d. Do not cut or gouge tanks, drums or containers until the prop­er steps have been taken to insure that such procedures will
not cause flammable or toxic vapors from substances inside.
They can cause an explosion even though they have been
“cleaned.” For information purchase “Recommended Safe
Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).

4.e. Vent hollow castings or containers before heating, cutting or
gouging. They may explode.

4.f. Do nor fuel engine driven equipment near area where plasma
cutting or gouging.

FUMES AND GASES
can be dangerous.

3.a. Plasma cutting or gouging may produce
fumes and gases hazardous to health. Avoid
breathing these fumes and gases.When cutting
or gouging, keep your head out of the fumes. Use
enough ventilation and/or exhaust at the arc to

CUTTING SPARKS can
cause fire or explosion.

4.a..Remove fire hazards from the plasma cutting
or gouging area. If this is not possible, cover
them to prevent the cutting or gouging sparks
from starting a fire. Remember that welding
sparks and hot materials from plasma cutting or

ii

SAFETY

ii

4.g. Sparks and spatter are thrown from the plasma arc. Wear safe­ty glasses, ear protection and oil free protective garments such
as leather gloves, heavy shirt, cuffless trousers, high shoes
and a cap over your hair. Wear ear plugs when cutting or goug­ing out of position or in confined places. Always wear safety
glasses with side shields when in a cutting or gouging area.

4.h. Connect the work cable to the work as close to the cutting or
gouging area as practical. Work cables connected to the build­ing framework or other locations away from the cutting or goug­ing area increase the possibility of the current passing through
lifting chains, crane cables or other alternate circuits. This can
create fire hazards or overheat lifting chains or cables until they
fail.

CYLINDER may explode
if damaged.

5.a. Use only compressed gas cylinders contain­ing the correct gas for the process used and
properly operating regulators designed for the

gas and pressure used. All hoses, fittings, etc.
should be suitable for the application and maintained in good
condition.

5.b. Always keep cylinders in an upright position securely chained
to an undercarriage or fixed support.

5.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from plasma cutting or gouging, arc weld-

ing operations and any other source of heat, sparks,
or flame.

5.d. Never allow any part of the electrode, torch or any other elec­trically “hot” parts to touch a cylinder.

5.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.

5.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for use.

5.g. Read and follow the instructions on compressed gas cylin­ders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,”available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY
powered equipment.

6.a. Turn off input power using the disconnect
switch at the fuse box before working on the
equipment.

6.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s rec­ommendations.

6.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.

PLASMA ARC can injure.

7.a. Keep your body away from nozzle and
plasma arc.

7.b. Operate the pilot arc with caution. The pilot arc is capable of
burning the operator, others or even piercing safety clothing.

ELECTRIC AND MAGNETIC FIELDS

may be dangerous

8.a. Electric current flowing through any conduc­tor causes localized Electric and Magnetic Fields
(EMF). Cutting or gouging current creates EMF
fields around torch cables and cutting machines.

8.b. EMF fields may interfere with some pace­makers, so operators having a pacemaker should consult
their physician before cutting or gouging.

8.c. Exposure to EMF fields during cutting or gouging may have
other health effects which are now not known.

8d. All operators should use the following procedures in order to

minimize exposure to EMF fields from the cutting or gouging
circuit:

8.d.1. Route the torch and work cables together - Secure
them with tape when possible.

8.d.2. Never coil the torch cable around your body.

8.d.3. Do not place your body between the torch and
work cables. If the torch cable is on your right side,

the work cable should also be on your right

side.

8.d.4. Connect the work cable to the workpiece as close as
possible to the area being cut or gouged.

8.d.5. Do not work next to cutting power source.

Apr. ‘93

NOTES

iv

SAFETY

iv

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv­antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher met­allique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble de

soudage et la machine à souder en bon et sûr état defonc­tionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le total
de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.

6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible de
la zone de travail qu’il est pratique de le faire. Si on place la
masse sur la charpente de la construction ou d’autres endroits
éloignés de la zone de travail, on augmente le risque de voir
passer le courant de soudage par les chaines de levage,
câbles de grue, ou autres circuits. Cela peut provoquer des
risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSA Standard
W 117.2-1974.

2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie du
corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel, donc:

a. Utiliser un bon masque avec un verre filtrant approprié ainsi

qu’un verre blanc afin de se protéger les yeux du rayon­nement de l’arc et des projections quand on soude ou
quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la peau

de soudeur et des aides contre le rayonnement de l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan­talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.

PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch­er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur place.

Mar. ‘93

for selecting a QUALITY product by Lincoln Electric. We want you

Thank You

to take pride in operating this Lincoln Electric Company product •••
as much pride as we have in bringing this product to you!

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the time
the shipment is received.

Please record your equipment identification information below for future reference. This information can be found
on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

vv

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

“Product Registration”. Please complete the form and submit your registration.

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.

CAUTION

This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.

PLASMA TORCH

TABLE OF CONTENTS

Page

SPECIFICATION SUMMARY ........................................................................................................A-1

GENERAL DESCRIPTION............................................................................................................A-2

INSTALLATION..............................................................................................................................A-2

OPERATION..................................................................................................................................B-1

MAINTENANCE ............................................................................................................................C-1

TORCH HEAD AND CABLE REPLACEMENT.......................................................................C-2

TROUBLESHOOTING ..................................................................................................................D-1

PARTS PAGES ..................................................................................................................P210-C,-G

vivi

PLASMA TORCH

A-1

SPECIFICATIONS SUMMARY

K880-1 PCT125 Hand-held Plasma Torch with 25 ft. (7.6m) cable
K880-2 PCT125 Hand-held Plasma Torch with 50 ft. (15.2m) cable
K880-3 PCT125M Plasma Machine Torch with 50 ft (15.2m) cable and 24 and 32 pitch gear racks
K880-4 PCT125M Robotic Plasma Torch with 50 ft (15.2m) cable
K880-5 PCT125 Hand-held Plasma Torch with 25 ft. (7.6m) cable

125 Amps, 60% Duty Cycle
100 Amps, 100% Duty Cycle

K880-1 PCT125 Hand-held Plasma Torch with 25 ft. (7.6m) cable, 11.5 lbs (5.2 kg)
K880-2 PCT125 Hand-held Plasma Torch with 50 ft. (15.2m) cable, 21.5 lbs (9.8 kg)
K880-3 PCT125M Plasma Machine Torch with 50 ft. (15.2m) cable, 21.5 lbs (9.8 kg)
K880-4 PCT125M Robotic Plasma Torch with 50 ft. (15.2m) cable, 21.5 lbs (9.8 kg)
K880-5 PCT125 Hand-held Plasma Torch with 25 ft. (7.6m) cable, 12.0 lbs. (5.4 kg)

INSTALLATION

TYPE

OUTPUT RATING

NET WEIGHT

A-1

TORCH COMPONENTS

Torch Electrode Swirl Ring Nozzle Cup

KP2045-1 Shield Cup with

K880-1 KP2042-1B1 .055" (1.4 mm) orifice
K880-2 KP2042-2B1 .067" (1.7 mm) orifice
K880-3 KP2042-3B1 .075" (1.9 mm) orifice
K880-4

K880-5 KP2042-2B1 .067" (1.7 mm) orifice

KP2043-1B1

KP2043-1B1

KP2044-1

KP2042-4B1 .118" (3.0 mm) orifice for gouging

KP2042-1B1 .055" (1.4 mm) orifice

KP2044-1

KP2042-3B1 .075" (1.9 mm) orifice
KP2042-4B1 .118" (3.0 mm) orifice for gouging

optional KP2046-1 standoff
guide or optional KP2047-1
gouging attachment.

S19974 Contact Cutting
Attachment with required
S19973 Contact Cutting
Insulator.

KP2045-1 or -2 Shield Cup
with optional KP2046-1
standoff guide or optional
KP2047-1 gouging attach­ment.

S19974 Contact Cutting
Attachment with required
S19973 or S19973-1
Contact Cutting Insulator.

Option Kits K881-1 Spare Parts Kit

K952-1 Robotic/Machine Torch Retrofit Kit (required when using a machine torch with a

machine code 10119 or below.)

Torch is no longer available.

PLASMA TORCH