Lincoln Electric OUTBACK 185 IM972, OUTBACK 185 Operator's Manual

Page 1
®
IM972
OUTBACK 185
For use with machines having Code Numbers:
Safety Depends on You
Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thoughtful operation on your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READ­ING THIS MANUAL AND THE SAFETY PRECAUTIONS CON­TAINED THROUGHOUT. And,
most importantly, think before you act and be careful.
11516
September, 2010
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Copyright © Lincoln Global Inc.
Page 2
®
i
SAFETY
i
WARNING
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents are known to the State of California to cause can­cer, birth defects, and other reproductive harm.
The Above For Diesel Engines
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
The Above For Gasoline Engines
FOR ENGINE powered equipment.
1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame welding arc or when the engine is running. Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporiz­ing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.
___________________________________________________
1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while the engine is running.
1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.
ELECTRIC AND MAGNETIC FIELDS may be dangerous
2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines
2.b. EMF fi elds m ay interf ere wi th some pacemak ers, a nd welders having a pacemaker should consult their physician before welding.
2.c. Exposure to EMF fields in welding may have other health effects which are now not known.
2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:
2.d.1.
Route the electrode and work cables together - Secure them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right side, the work cable should also be on your right side.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.
2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.
2.d.5. Do not work next to welding power source.
Page 3
®
ii
SAFETY
ii
ELECTRIC SHOCK can kill.
3.a. The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these “hot” parts with your bare skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation. Make certain the insulation is large enough to cover your full area of physical contact with work and ground.
In addition to the normal safety precautions, if welding must be performed under electrically hazardous conditions (in damp locations or while wearing wet clothing; on metal structures such as floors, gratings or scaffolds; when in cramped positions such as sitting, kneeling or lying, if there is a high risk of unavoidable or accidental contact with the workpiece or ground) use the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode, electrode reel, welding head, nozzle or semiautomatic welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical connection with the metal being welded. The connection should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical (earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and welding machine in good, safe operating condition. Replace damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of electrode holders connected to two welders because voltage between the two can be the total of the open circuit voltage of both welders.
3.i. When working above floor level, use a safety belt to protect yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant material to protect your skin and that of your helpers from the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable screening and/or warn them not to watch the arc nor expose themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES can be dangerous.
5.a. Welding ma y produce fumes and gases hazardous to health. Avoid breathing these fumes and gases. When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special ventilation such as stainless or hard facing (see instructions on container or MSDS) or on lead or cadmium plated steel and other metals or coatings which produce highly toxic fumes, keep exposure as low as possible and within applicable OSHA PEL and ACGIH TLV limits using local exhaust or mechanical ventilation. In confined spaces or in some circum­stances, outdoors, a respirator may be required. Additional precautions are also required when welding on galvanized steel.
5. b. The operation of welding fume control equipment is affected by various factors including proper use and positioning of the equipment, maintenance of the equipment and the spe­cific welding procedure and application involved. Worker exposure level should be checked upon installation and periodically thereafter to be certain it is within applicable OSHA PEL and ACGIH TLV limits.
5.c.
Do not weld in locations near chlorinated hydrocarbon coming from degreasing, cleaning or spraying operations. The heat and rays of the arc can react with solvent vapors form phosgene, a highly toxic gas, and other irritating prod­ucts.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation, especially in confined areas, to insure breathing air is safe.
vapors
to
5.e. Read and understand the manufacturerʼs instructions for this
equipment and the consumables to be used, including the material safety data sheet (MSDS) and follow your employerʼs safety practices. MSDS forms are available from your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
Page 4
®
iii
SAFETY
iii
WELDING and CUTTING SPARKS can cause fire or explosion.
6.a.
Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.
6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even been “cleaned”. For information, purchase “Recommended Safe Practices for the Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.
Sparks and spatter are thrown from the welding arc. Wear oil
6.f. free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.
6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate cir­cuits. This can create fire hazards or overheat lifting chains or cables until they fail.
6.h. Also see item 1.c.
the welding sparks from starting a fire.
though
they have
Preparation
for Welding and Cutting of
CYLINDER may explode if damaged.
7.a. Use on ly com pr essed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.
7.b. Alway s keep cylinders in an upright position securely chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.
7.g. Re ad and foll ow the inst ru ctions o n c ompressed ga s cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.
FOR ELECTRICALLY powered equipment.
8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.
8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturerʼs recommendations.
8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturerʼs recommendations.
6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During Welding, Cutting and Other Hot Work”, available from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Refer to http://www.lincolnelectric.com/safety for additional safety information.
Page 5
®
iv
SAFETY
iv
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv­antes:
Sûreté Pour Soudage A LʼArc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à lʼélectrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours tout contact entre les parties sous tension et la peau nue ou les vétements mouillés. Porter des gants secs et sans trous pour isoler les mains.
b. Faire trés attention de bien sʼisoler de la masse quand on
soude dans des endroits humides, ou sur un plancher metallique ou des grilles metalliques, principalement dans les positions assis ou couché pour lesquelles une grande partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état defonctionnement.
d.Ne jamais plonger le porte-électrode dans lʼeau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder parce que la tension entre les deux pinces peut être le total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions pour le porte-électrode sʼapplicuent aussi au pistolet de soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger contre les chutes dans le cas ou on recoit un choc. Ne jamais enrouler le câble-électrode autour de nʼimporte quelle partie du corps.
5. Toujours porter des lunettes de sécurité dans la zone de soudage. Utiliser des lunettes avec écrans lateraux dans les zones où lʼon pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de prévenir tout risque dʼincendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de la masse. Un court-circuit accidental peut provoquer un échauffement et un risque dʼincendie.
8. Sʼassurer que la masse est connectée le plus prés possible de la zone de travail quʼil est pratique de le faire. Si on place la masse sur la charpente de la construction ou dʼautres endroits éloignés de la zone de travail, on augmente le risque de voir passer le courant de soudage par les chaines de lev­age, câbles de grue, ou autres circuits. Cela peut provoquer des risques dʼincendie ou dʼechauffement des chaines et des câbles jusquʼà ce quʼils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage. Ceci est particuliérement important pour le soudage de tôles galvanisées plombées, ou cadmiées ou tout autre métal qui produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant dʼopérations de dégraissage, nettoyage ou pistolage. La chaleur ou les rayons de lʼarc peuvent réagir avec les vapeurs du solvant pour produire du phosgéne (gas fortement toxique) ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir le code “Code for safety in welding and cutting” CSA Standard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
3. Un coup dʼarc peut être plus sévère quʼun coup de soliel, donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi quʼun verre blanc afin de se protéger les yeux du ray­onnement de lʼarc et des projections quand on soude ou quand on regarde lʼarc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de lʻarc.
c. Protéger lʼautre personnel travaillant à proximité au
soudage à lʼaide dʼécrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de lʼarc de soudage. Se protéger avec des vêtements de protection libres de lʼhuile, tels que les gants en cuir, chemise épaisse, pan­talons sans revers, et chaussures montantes.
LES MACHINES À SOUDER À TRANSFORMATEUR ET À REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de lʼélectricité et aux recommendations du fabricant. Le dispositif de montage ou la piece à souder doit être branché à une bonne mise à la terre.
2. Autant que possible, Iʼinstallation et lʼentretien du poste seront effectués par un électricien qualifié.
3. Avant de faires des travaux à lʼinterieur de poste, la debranch­er à lʼinterrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur place.
Page 6
Thank You
vv
for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip­ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses­sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor­mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customerʼs particular purpose, with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.
CUSTOMER ASSISTANCE POLICY
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received.
Please record your equipment identification information below for future reference. This information can be found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection. The level of seriousness to be applied to each is explained below:
WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
Page 7
TABLE OF CONTENTS
Page
Installation.......................................................................................................................Section A
Technical Specifications.......................................................................................................A-1
Safety Precautions. ..............................................................................................................A-2
Location and Ventilation................................................................................................A-2
Storing...........................................................................................................................A-2
Stacking ........................................................................................................................A-3
Tilting.............................................................................................................................A-3
Lifting.............................................................................................................................A-3
Pre-Operation Engine Service..............................................................................................A-3
Oil..................................................................................................................................A-3
Fuel ...............................................................................................................................A-3
Spark Arrester ...............................................................................................................A-3
Electrical and Welding Connections.....................................................................................A-4
Machine Grounding.......................................................................................................A-5
Plugs and Hand-Held Equipment, Auxiliary Power Receptacles .........................................A-6
Premises Wiring ...................................................................................................................A-6
Circuit Breakers....................................................................................................................A-6
Electrical Devices used with the Outback™ 185..................................................................A-7
________________________________________________________________________________
Operation.........................................................................................................................Section B
Safety Instructions................................................................................................................B-1
Symbols................................................................................................................................B-2
General Description..............................................................................................................B-3
Recommended Applications.................................................................................................B-3
Operational Features and Controls ......................................................................................B-3
Design Features and Advantages ........................................................................................B-3
Welding Capability................................................................................................................B-3
Limitations ............................................................................................................................B-3
Controls and Settings ...........................................................................................................B-4
Welder/Generator Controls ..................................................................................................B-4
Engine Operation .................................................................................................................B-5
Welding Operation................................................................................................................B-6
Auxiliary Power.....................................................................................................................B-7
Electrode selection Guide .............................................................................................B-7
Auxiliary Power Application ..................................................................................................B-8
________________________________________________________________________________
vivi
Accessories.....................................................................................................Section C
General Options / Accessories..............................................................................C-1
________________________________________________________________________
Maintenance ....................................................................................................Section D
Safety Precautions ................................................................................................D-1
Routine and Periodic Engine Maintenance....................................................D-1, D-2
________________________________________________________________________
Troubleshooting..............................................................................................Section E
How to Use Troubleshooting Guide.......................................................................E-1
Troubleshooting Guide.............................................................................E-2 thru E-4
________________________________________________________________________
Wiring Diagram and Dimension Print............................................................Section F
________________________________________________________________________
Parts List.....................................................................................................P-591 Series
________________________________________________________________________
Page 8
A-1
®
INSTALLATION
A-1
TECHNICAL SPECIFICATIONS -
OUTBACK™ 185 (K2706-1)
INPUT - GASOLINE ENGINE
Make/Model Description Speed (RPM) Displacement Ignition Capacities
System
KOHLER 1 cylinder CS 12.75 4 cycle 1825RPM Low Idle (360 cc) Start; (24.9L)
air-cooled 3400RPM Full Load OHV gasoline Bore x Stroke
12.75 HP @ Choke (1.1L) 3600 RPM 3.35” x 2.48”
Aluminum Block
w/ Cast Iron Sleeve
3750RPM High Idle 21.96 cu. in
(85 mm x 63mm)
Electric & Recoil
Manual
Fuel: 6.86 gal.
Oil: 1.2 Qts.
RATED OUTPUT - WELDER
AMPS @ DC CONSTANT CURRENT DUTY CYCLE VOLTS @ RATED AMPERES
100 100% 25 130 60% 25 150 20% 25 185 MAX OUTPUT ---
OUTPUT -WELDER AND GENERATOR
Welding Ranges Welding Open Circuit Voltage AC Auxiliary Power
4600 Watts 115V 1PH
100% Duty Cycle
50 - 185 Amps DC 80 VDC Max. 5700 Peak Watts
5200 Continuous Watts 120 / 230 V 1PH
PHYSICAL DIMENSIONS
HEIGHT WIDTH DEPTH WEIGHT
25.47 in. 21.12 in. 31.48 in. 310.0 lbs.
646.94 mm 536.45 mm 799.59 mm 140.6 kg
OPERATING TEMPERATURE RANGE STORAGE TEMPERATURE RANGE
0° F TO 104° F (-18° C TO 40° C) -40° F TO 131° F (-40° C TO 55° C)
OUTBACK™ 185
Page 9
A-2
®
INSTALLATION
A-2
SAFETY PRECAUTIONS
Read this entire installation section before you start installation.
WARNING
Do not attempt to use this equipment until you have thoroughly read all operating and mainte­nance manuals supplied with your machine. They include important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists.
Hazards of Electric Shock, Engine Exhaust & Moving Parts
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or electrode with skin or wet cloth­ing.
• Insulate yourself from work and
ground.
• Always wear dry insulating gloves.
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or vent exhaust outside.
• Do not stack anything on or near the engine.
MOVING PARTS can injure.
• Do not operate with doors open or guards off.
• Stop engine before servicing.
• Keep away from moving parts.
Only qualified personnel should install, use, or service this equipment.
LOCATION AND VENTILATION
Whenever you use the clean cooling air can flow around the machineʼs gasoline engine and the generator. Avoid dusty, dirty areas. Also, keep the machine away from heat sources. Do not place the back end of the generator anywhere near hot engine exhaust from another machine. And of course, make sure that engine exhaust is ventilated to an open, outside area.
OUTBACK™ 185
The the machine in puddles or otherwise submerge it in water. Such practices pose safety hazards and cause improper operation and corrosion of parts.
Always operate the on and all machine components completely assembled. This will help to protect you from the dangers of moving parts, hot metal surfaces, and live electrical devices.
OUTBACK™ 185
must be used outdoors. Do not set
OUTBACK™ 185
, be sure that
with the case roof
STORING
1. Store the machine in a cool, dry place when it is not in use. Protect it from dust and dirt. Keep it where it can not be accidentally damaged from construction activi­ties, moving vehicles and other hazards.
2. If you will be storing the machine for over 30 days, you should drain the fuel to protect fuel system and carbure­tor parts from gum deposits. Empty all fuel from the tank and run the engine until it stops from lack of fuel.
3. You can store the machine for up to 24 months if you use a stabilizing Additive in the fuel system. Mix the additive with the fuel in the tank and run the engine for a short time to circulate the additive through the carbu­retor.
4. While the engine is still warm, drain the oil and refill with fresh 10W30 oil.
5. Remove the spark plug and pour approximately 1/2 ounce (15ml) of engine oil into the cylinder. Replace the spark plug and crank the engine slowly to distribute the oil.
6. Clean any dirt and debris from the cylinder and cylinder head fins and housing, rotating screen, and muffler areas.
7. Store in a clean, dry area.
OUTBACK™ 185
Page 10
A-3
®
STACKING
INSTALLATION
OIL
A-3
OUTBACK™ 185 machines CANNOT be stacked.
TILTING
Place the machine on a secure, level surface whenev­er you use it or store it. Any surfaces you place it on other than the ground must be firm, non-skid, and structurally sound.
The gasoline engine is designed to run in a level posi­tion for best performance. It can operate at an angle, but this should never be more than 15 degrees in any direction. If you do operate it at a slight angle, be sure to check the oil regularly and keep the oil level full. Also, fuel capacity will be a little less at an angle.
LIFTING
The OUTBACK™ 185 should be lifted by two people. (See Specification section for weight). The LowLift™ grab bars on both ends make lifting easier.
PRE-OPERATION ENGINE SERVICE
Read and understand the engine operating and
maintenance instructions supplied with this machine
before you operate the OUTBACK™ 185.
The OUTBACK™ 185 is shipped with the engine filled with SAE 10W30 oil. CHECK THE OIL LEVEL BEFORE YOU START THE ENGINE. This is an added precaution. Do not screw in dipstick when checking oil level. DO NOT OVERFILL. Be sure the fill plug is tight after servicing.
FUEL
Fill the fuel tank with clean, fresh, regular grade (mini­mum 87 octane lead free WITH GAS. The OUTBACK™ 185 capacity is approx­imately 6.8 gallons (25.74 Liter). DO NOT OVER- FILL, allow room in the fuel tank for fuel expansion.
gasoline. DO NOT MIX OIL
SPARK ARRESTER
Some federal, state or local laws may require gaso­line engines to be equipped with exhaust spark arresters when they are operated in certain locations where unarrested sparks may present a fire hazard. The standard muffler included with this machine does not qualify as a spark arrester. For areas requiring spark arrestors, use K2793-1.
CAUTION
WARNING
• Keep hands away from muffler or HOT engine parts.
• Stop the engine when fueling.
• Do not smoke when fueling.
• Remove fuel cap slowly to release pressure.
• Do not overfill tank.
• Wipe up spilled fuel and allow fumes to clear before starting engine.
• Keep sparks and flame away from tank.
------------------------------------------------------------------------
An incorrect additional arrester may lead to dam­age to the engine or adversely affect performance.
------------------------------------------------------------------------
OUTBACK™ 185
Page 11
A-4
®
INSTALLATION
A-4
2
OUTBACK™ 185 OUTPUT CONNECTIONS
3
10
6
9
7
8
5 4
1
10
8
1
7
9
3
4
5
6
2
FIGURE A.1
1. CURRENT CONTROL DIAL
2. WELD OUTPUT TERMINALS (2)
3. GROUND STUD
4. CIRCUIT BREAKERS (2) - 20 AMP
5. CIRCUIT BREAKER 30 Amp
6. RECEPTACLE - 240 VOLT, 50 AMP
ELECTRICAL OUTPUT CONNECTIONS
See Figure A.1 for the location of the current control
dial, weld output terminals, ground stud, circuit break­ers, 240 and 120 volt receptacles.
WELDING CABLE CONNECTIONS
Cable Size and Length
Be sure to use welding cables that are large enough. The correct size and length becomes especially impor­tant when you are welding at a distance from the welder.
7. DUPLEX RECEPTACLE (2)- 120 VOLT, 20 AMP
8. HOURMETER
9. ENGINE SWITCH
10. CHOKE
TABLE A.1
RECOMMENDED WELDING CABLE
SIZE AND LENGTH
TOTAL COMBINED LENGTH OF
ELECTRODE AND WORK CABLES
Cable
Length
0-50 ft (0-15m)
50-100 ft (15-30 m)
100-150 ft (30-46 m)
125 Amps
30% Duty Cycle
6 AWG
5 AWG
3 AWG
Table A.1 lists recommended cable sizes and lengths for rated current and duty cycle. Length refers to the distance from the welder to the work and back to the welder. Cable diameters are increased for long cable lengths to reduce voltage drops.
150-200 ft (46-61 m)
200-250 ft (61-76m)
OUTBACK™ 185
2 AWG
1 AWG
Page 12
A-5
®
Cable Installation
INSTALLATION
MACHINE GROUNDING
A-5
Install the welding cables to your OUTBACK™ 185 as follows. See Figure A.1 for the location of parts.
1. The gasoline engine must be OFF to install weld­ing cables.
2. Remove the 1/2-13 flanged nuts from the output terminals.
3. Connect the electrode holder and work cables to the weld output terminals. Normally, the electrode cable is connected to the positive (+) output stud.
4. Tighten the flanged nuts securely.
5. Be certain that the metal piece you are welding (the “work”) is securely connected to the work clamp and cable.
6. Check and tighten the connections periodically.
CAUTION
Loose connections will cause the output studs to
overheat and the studs may eventually melt.
Do not cross welding cables at output stud connec-
tion. Keep isolated and separate from one another.
------------------------------------------------------------------------
Because this portable engine driven welder or genera­tor creates its own power, it is not necessary to con­nect its frame to an earth ground, unless the machine is connected to premises wiring (your home, shop, etc.).
To prevent dangerous electric shock, other equipment to which this engine driven welder supplies power, must:
a) be grounded to the frame of the welder using a
grounded type plug or
b) be double insulated
When this welder is mounted on a truck or trailer, the machine grounding stud must be securely con­nected to the metal frame of the vehicle.
In general if the machine is to be grounded, it should be connected with a #8 or larger copper wire to a solid earth ground such as a metal water pipe going into the ground for at least ten feet and having no insulat­ed joints, or to the metal framework of a building which has been effectively grounded. The U.S. National Electrical Code lists a number of alternate means of grounding electrical equipment. A machine grounding stud marked with the symbol is provid­ed on the front of the welder.
WARNING
Lincoln Electric offers a welding accessory kit with #6 welding cables. See the ACCESSORIES section of this manual for more information.
For more information on welding , see WELDING OPERATION in the OPERATION section of this man­ual.
DO NOT GROUND MACHINE TO A PIPE WHICH CARRIES EXPLOSIVE OR COMBUSTIBLE MATERIAL.
------------------------------------------------------------------------
OUTBACK™ 185
Page 13
A-6
®
INSTALLATION
PLUGS AND HAND HELD EQUIPMENT
A-6
PREMISES WIRING
For further protection against electric shock, any elec­trical equipment connected to the generator recepta­cles must use a three-blade, grounded type plug or an Underwriterʼs Laboratories (UL) approved double insulated tool with a two blade plug.
WARNING
Never operate this machine with damaged or defective cords. All electrical equipment must be in safe operating condition.
------------------------------------------------------------------------
AUXILIARY POWER RECEPTACLES
The control panel of the OUTBACK™ 185 features three auxiliary power receptacles:
Two 20 amp,120 volt duplex (double outlet) receptacle.
A 50 amp, 240 volt single outlet receptacle.
See Figure A.1
Through these receptacles the machine can supply up to 5700 watts surge or 5200 watts continuous of sin­gle-phase 60 Hertz AC power. The machine output voltages meet UL standards and fall within ± 10% of the rated voltage.
The OUTBACK™ 185 is not recommended for premises wiring. The OUTBACK™ 185 does not have a combined 120/240 volt receptacle and cannot be connected to a premises as described in other Lincoln literature.
The OUTBACK™ 185 is intended only for backup, intermittent use power. Certain electrical devices can­not be powered by the OUTBACK™ 185. Refer to Table A.2 for these devices.
CIRCUIT BREAKERS
Auxiliary power is protected by circuit breakers. When the machine is operated in high temperature environ­ments, the breakers may tend to trip at lower loads than normally.
CAUTION
NEVER BYPASS THE CIRCUIT BREAKERS. WITHOUT OVERLOAD PROTECTION, THE UNIT COULD OVERHEAT AND/OR CAUSE DAMAGE TO THE EQUIPMENT BEING USED.
------------------------------------------------------------------------
OUTBACK™ 185
Page 14
A-7
®
INSTALLATION
CAUTION
Certain Electrical devices cannot be powered by the OUTBACK™ 185. See Table A.2
TABLE A.2
ELECTRICAL DEVICE USE WITH THE OUTBACK™ 185
A-7
Type
Resistive
Capacitive
Inductive
Common Electrical Devices
Heaters, toasters, incandescent light bulbs, electric range, hot pan, skillet, coffee maker.
TV sets, radios, microwaves, appliances with electrical control.
Single-phase induction motors, drills, well pumps, grinders, small refrigerators, weed and hedge trimmers.
Possible Concerns
NONE
Voltage spikes or high voltage regulation can cause the capac­itative elements to fail. Surge protection, transient protection, and additional loading is recom­mended for 100% fail-safe opera­tion. DO NOT RUN THESE DEVICES WITHOUT ADDITIONAL RESISTIVE TYPE LOADS.
These devices require large current inrush for starting. (See Table B.3, GENERATOR POWER APPLICATIONS, in the OPERA­TION section of this manual for required starting wattages.) Some synchronous motors may be frequency sensitive to attain maximum output torque, but they SHOULD BE SAFE from any frequency induced failures.
Capacitive / Inductive
The Lincoln Electric Company is not responsible for any damage to electrical components improperly connected to a OUTBACK™ 185.
Computers, high resolution TV sets, complicated electrical equipment.
OUTBACK™ 185
An inductive type line condition­er along with transient and surge protection is required, and liabilities still exist. DO NOT USE THESE DEVICES WITH A OUTBACK™ 185.
Page 15
B-1
®
SAFETY INSTRUCTIONS
OPERATION
B-1
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or electrode with skin or wet clothing.
• Insulate yourself from work and ground.
• Always wear dry insulating gloves.
FUMES AND GASES can be dangerous.
• Keep your head out of fumes.
• Use ventilation or exhaust to remove fumes from breathing zone.
WARNING
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or vent exhaust outside.
• Do not stack anything on or near the engine.
MOVING PARTS can injure.
• Do not operate with doors open or guards off.
• Stop engine before servicing.
• Keep away from moving parts.
Only qualified personnel should install, use, or service this equipment.
Observe additional Safety Guidelines detailed throughout this manual.
WELDING SPARKS can cause fire or explosion
• Keep flammable material away.
• Do not weld on containers that have held combustibles.
ARC RAYS can burn.
• Wear eye, ear and body protection.
OUTBACK™ 185
Page 16
B-2
®
OPERATION
GRAPHIC SYMBOLS USED ON THIS EQUIPMENT OR IN THIS MANUAL
B-2
WARNING /
CAUTION
OIL
FUEL
WORK CLAMP
FAST
CHOKE
AIR CLEANER
CIRCUIT
BREAKER
GROUND
(AUXILIARY
POWER)
ELECTRODE
WELDING ARC
SLOW
AUTO IDLE
ENGINE OFF
ENGINE START
OUTBACK™ 185
Page 17
B-3
®
OPERATION
B-3
GENERAL DESCRIPTION
The OUTBACK™ 185 is designed for commercial use welder/generator applications. As a welder it provides 185 amps of DC constant current for welding with DC stick electrodes. A single dial lets you select a full range of welding output from 50 to 185 amps.
As a generator it can supply up to 5700 surge watts or 5200 continuous watts of 120 / 240 volt, single-phase AC power. The machine is portable.
A Kohler CS 12.75 HP air cooled, OHV gasoline engine powers the welder / generator. It has an engine warranty of 3 years.
RECOMMENDED APPLICATIONS
Welder
The OUTBACK™ 185 provides excellent constant current DC welding output for stick (SMAW) welding.
Generator
The OUTBACK™ 185 gives smooth AC generator output for continuous auxiliary power usage within the engine manufacturerʼs required maintenance recom­mendations.
OPERATIONAL FEATURES AND CONTROLS
DESIGN FEATURES AND ADVANTAGES
• 185 amp DC constant current welding for stick electrodes.
• Lightweight / portable.
• Full range, continuous welding output control with a single knob.
• Automatic shutdown under low oil level condition.
• Hour Meter Standard.
• 5700 Surge watts or 5200 Watts of continuous 120 / 240 volt single phase AC auxiliary power.
• Kohler CS 12.75 HP overhead cam air-cooled gasoline engine. Smooth running, long life.
WELDING CAPABILITY
The OUTBACK™ 185 rated 185 amps, 20 VDC at 10% duty cycle on a ten-minute basis. This means that you can load the welder to 185 amps for one minute out of every ten-minute period. The machine is capable of higher duty cycles at lower output cur­rents. For example, you can load the welder to 120 amps for ten minutes out of ten for a 100% duty cycle.
The current is continuously variable from 50 to 185 amps DC. The OUTBACK™ 185 can, therefore, weld with all 3/32”, 1/8” and most 5/32” diameter Lincoln DC electrodes.
The OUTBACK™ 185 was designed for simplicity. Therefore, it has very few operating controls. A single dial on the control panel lets you select either welder or generator use. For welding, the same dial selects continuous current output over the machineʼs 50 to 185 amp range.
The gasoline engine controls include a recoil starter, choke and stop switch. See ENGINE OPERATION in the OPERATION section of this manual for details about starting, running, stopping, and breaking in the gasoline engine.
LIMITATIONS
• The OUTBACK™ 185 is not recommended for any processes besides those that are normally per­formed using stick welding (SMAW) procedures.
• The OUTBACK™ 185 is not recommended for pipe thawing.
• During welding, generator power is limited to 100 watts, and output voltages can drop from 120 to 80 volts and 240 to 160 volts. Therefore, DO NOT OPERATE ANY SENSITIVE ELECTRICAL EQUIPMENT WHILE YOU ARE WELDING.
OUTBACK™ 185
Page 18
B-4
®
OPERATION
B-4
CONTROLS AND SETTINGS All welder/generator controls are located on the Output Control Panel.
Gasoline engine controls are mounted on the engine. See Figure B.1 and the figures in engine operation section.
3 or 4
6
5
11
8 12 2 7
9 1 10
12
11
OUTPUT PANEL CONTROLS
10
1
9
7
2
8
6
3 or 4
5
WELDER/GENERATOR CONTROLS
See Figure B.1 for the location of the following features:
1. CURRENT CONTROL DIAL: Adjusts continuous cur­rent output. The amperages on the dial correspond to the approximate amperages needed for specific Lincoln welding electrodes.
2. 30 AMP CIRCUIT BREAKER: Provide separate over­load current protection for the 120 Volt and 240 Volt Receptacles
3. WELD POSITIVE OUTPUT TERMINAL: Pro vides the connection point for either the electrode holder or the work cable. (Because the OUTBACK™ 185 is a DC output machine, either output terminal can be used for either cable.)
4. WELD NEGATIVE OUTPUT TERMINAL: Provides the
connection point for either the electrode holder or the work cable. (Because the OUTBACK™185 is a DC output machine, either output terminal can be used for either cable.)
5. GROUND STUD: Provides a connection point for con­necting the machine case to earth ground for the safest grounding procedure.
6. CIRCUIT BREAKER: Provides overload protection for
weld output terminals.
7. CIRCUIT BREAKERS (2): Provide separate overload current protection for the 120 volt and 240 volt recepta­cles
8. 240 VOLT RECEPTACLE: Connection point for sup­plying 250 volt power to operate one electrical device.
9. 120 VOLT DUPLEX RECEPTACLES (2): Connection point for supplying 120 volt power to operate devices needed for maintenance purposes.
FIGURE B.1
10. HOUR METER: Records the time that the engine has run for maintenance purposes.
11. ENGINE CHOKE: Engine starting aid.
12. ENGINE SWITCH:
Used to start the engine, Select High Idle or Auto Idle while the engine is running and stops the engine.
When placed in the “OFF” position, the ignition
circuit is de-energized to shut down the engine.
When held in the “START” position, the engine starter motor is energized.
When in “HIGH IDLE” ( ) position, the engine will run continuously at high idle.
When in “AUTO IDLE” ( / ) position, the engine will run continuously and the idler operates as follows:
• Welding
When the electrode touches the work, the welding arc is initiated and the engine accelerates to full speed. After welding ceases (and no auxiliary power is being drawn), the engine will return to low idle after approximately 10 to 14 seconds.
• Auxiliary Power
With the engine running at low idle and auxiliary power for lights or tools is drawn (approximately 0­150 watts or greater) from the receptacles, the engine will accelerate to high speed. If no power is being drawn from the receptacles (and not welding) for 10-14 seconds, the idler reduces the engine speed to low idle.
OUTBACK™ 185
Page 19
B-5
®
OPERATION
B-5
ENGINE OPERATION
Starting/Shutdown Instructions
Be sure all Pre-Operation Engine Service has been performed. Also, Read owners manual before starting for the first time. (See INSTALLATION section)
Remove all loads connected to the AC power recepta­cles. Before starting, first open the fuel shutoff valve.
Always pull the choke control out when starting the engine; cold, warm or hot.
Turn the engine switch to the “Start” position and crank the engine until it starts, slowly return the choke control to the full “in” position (choke open), and turn the switch to the Auto Idle ( / ) position. Do not turn the switch to the “start” position while the engine is running because this will cause damage to the ring gear and/or starter motor.
Stopping the Engine
Remove all welding and auxiliary power loads and allow engine to run for a few minutes to cool the engine.
Break-in Period
It is normal for any engine to use larger quantities of oil until break-in is accomplished. Check the oil level twice a day during the break-in period (about 50 run­ning hours). Change the oil after the first 5 hours of operation. See the Engine Instruction Manual for fur­ther details.
CAUTION
IN ORDER TO ACCOMPLISH THIS BREAK-IN, THE UNIT SHOULD BE SUBJECTED TO MODERATE LOADS, WITHIN THE RATING OF THE MACHINE. AVOID LONG IDLE RUNNING PERIODS. REMOVE LOADS AND ALLOW ENGINE TO COOL SEVERAL MINUTES AT LOW IDLE BEFORE SHUTDOWN.
------------------------------------------------------------------------
Low Oil Sensing
This engine has a built in sensor which responds to low oil level (not pressure). When activated, the sys­tem will shut the engine down. The engine will not restart until sufficient oil is added. Check oil level fre­quently and add oil as required to the full mark on the dipstick. DO NOT OVERFILL.
Stop the engine by placing the engine switch in the “Off” ( ) position.
WARNING
Close the fuel valve when the machine is transported to prevent fuel leakage from the carburetor.
------------------------------------------------------------------------
Typical Fuel Consumption
KOHLER CS 12.75 HP
NO LOAD 2250 R.P.M .75
NO LOAD .40 GALLONS/HOUR 3750 R.P.M. 1.51 ( LITERS/HOUR)
DC CC WELD OUTPUT .73 GALLONS/HOUR 100 AMPS, 25 VOLTS 2.77 ( LITERS/HOUR)
AUXILIARY POWER .99 GALLONS/HOUR 5200 KVA 3.74 ( LITERS/HOUR)
. .20 GALLONS/HOUR
( LITERS/HOUR)
OUTBACK™ 185
Page 20
B-6
®
OPERATION
B-6
WELDING OPERATION
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or electrode with skin or wet cloth­ing.
• Insulate yourself from work and
ground.
• Always wear dry insulating gloves.
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas
or vent exhaust outside.
• Do not stack anything on or near
the engine.
MOVING PARTS can injure.
• Do not operate with doors open or guards off.
• Stop engine before servicing.
• Keep away from moving parts.
Only qualified personnel should install, use, or service this equipment.
The OUTBACK™ 185 can deliver from 50 to 185 amps of welding output current . Output can be adjusted by setting the current control dial on the out­put control panel.
You can get maximum welding output by setting the dial to 185 AMPS. At high current settings like this, some output may decrease as the machine is used. If you are welding for a long time, you may need to turn the dial slightly upward to maintain the same results.
The numbers on the dial correspond to the approxi­mate amps needed to weld using specific Lincoln welding rods. Table B.2, WELDING APPLICATIONS, give you the recommended dial settings based on the thickness of the work and the size and type of rod youʼre using.
TO USE THE OUTBACK 185 FOR WELDING:
1. Remove the flange nuts from the weld output ter­minals and place the work and electrode welding cables over the terminals. See Figure B.1 and B.1a. Replace and tighten the flange nuts securely. Be sure the connections are tight.
2. Select the appropriate electrode. See Table B.2
3. Attach the work clamp securely to the work you are welding.
4. Insert the electrode into the electrode hold
5. Set the current control dial to the desired output current .
6. Start the gasoline engine. See ENGINE OPERATION in this section of
the manual.
7. Strike an arc and begin welding.
AFTER YOU FINISH THE WELD:
1. Stop the gasoline engine. See ENGINE OPERA-
TION in this section of the manual.
2. Allow the electrode and work to cool completely.
3. Remove the work clamp from the work.
4. Remove any remaining piece of electrode from the
electrode holder.
5. If you are finished using the OUTBACK 185 for weld-
ing, disconnect the welding cables from the weld out­put terminals. Reattach the flange nuts and leave
them on the terminals. For DC+ welding, the electrode cable is to be connected to the “+” output stud and work cable to the “-” output stud. (For DC- welding, reverse these connections.)
Semi-automatic Wire Welding with a Lincoln Wire Feeder/Welder
The
OUTBACK™ 185 supply up to 5,200 watts continuous input power to a Lincoln Wire Feeder/Welder. The Wire Feeder/ Welder is equipped with all the supplies needed for Flux-Cored Arc Welding (FCAW). Also some Wire Feeder/Welders come equipped with the essentials needed for Gas Metal Arc Welding (GMAW) or MIG processes, while others require the purchase of a conversion kit. These products are available where Lincoln products are sold. Contact your local authorized Lincoln representative for more details.
Plasma Cutting with Lincoln Pro-Cut 25.
The
OUTBACK™ 185 supply up to 5,200 watts continuous input power to a Pro-Cut 25. The Pro-Cut will work satisfactorily under the following conditions:
1. Set the Current Control on the
the 185 amp position. (Higher Settings may result in a shutdown of the Pro-Cut 25.)
2. Leave the "ON/OFF" switch on the Pro-Cut "OFF"
until the OUTBACK 185 has been started and is at full operating speed.
generator power can be used to
generator power can be used to
OUTBACK™ 185
er.
to
OUTBACK™ 185
Page 21
B-7
®
OPERATION
B-7
120V Receptacle Operation:
• Set the Output Control on the Pro-Cut 25 no higher than the 15 amp position.( Higher settings may cause circuit breaker on the
OUTBACK™ 185
to trip.)
• Maximum material thickness that can be cut is 1/4".
240V Receptacle Operation:
• The Pro-Cut 25 may be used for its full range of con­trol.
• Maximum material thickness that can be cut is 3/8".
AUXILIARY POWER OPERATION
WARNING
Be sure that any electrical equipment plugged into the generator AC power receptacles can withstand a ±10% voltage and a ±5% frequency variation. Some electronic devices cannot be powered by the OUT­BACK 185 Refer to Table A.2, ELECTRICAL DEVICE USE WITH THE OUTBACK™ 185, in the INSTALLA­TION section of this manual.
Electrical loads in watts are calculated by multiplying the voltage rating of the load by the number of amps it draws. (This information is given on the load device nameplate.) For example, a device rated 120 volts, 2 amps will need 240 watts of power (120 x 2 = 240).
You can use Table B.3, AUXILIARY POWER APPLI­CATIONS, to determine the wattage requirements of the most common types of loads you can power with the OUTBACK™ 185 Be sure to read the notes at the bottom of the table.
TO USE THE OUTBACK 185 AS AN AUXILIARY POWER SUPPLY:
1. Start the gasoline engine. See ENGINE OPERA­TION in this section of the manual.
2. Set the current control dial on the output control panel to “MAX.” See Figure B.1.
3. Plug the load(s) into the appropriate 120 volt or 240 volt power receptacle.
NOTE: During welding, the maximum generator output for auxiliary
loads is 100 watts.
GENERAL INFORMATION
The OUTBACK™ 185 is rated at 5700 Peak watts or 5200 continuous watts. It provides both 120 volt and 240 volt power. You can draw up to 20 amps from either side of the 120 volt duplex receptacle, but not more than 35.4 amps from both sides at once. Up to
17.7 amps can be drawn from the single 240 volt receptacle.
TABLE B.2
ELECTRODE SELECTION GUIDE
AWS ELECTRODE
CLASSIFICATION ELECTRODE TYPE POLARITY
E6010 FLEETWELD® 5P DC+ 50-75 75-135 90-175 E6011 FLEETWELD® 35 DC+ 50-75 70-110 80-145 E6011 FLEETWELD® 180 DC+ 50-80 55-110 105-135 E6013 FLEETWELD® 37 DC± 70-95 100-135 145-180 E7018 EXCALIBUR® 7018 DC+ 70-100 90-125 125-185 E7018 JETWELD® LH-73 DC+ 65-85 90-125 130-185
E708-17 & E308L-17
ENi-CI SOFTWELD® 99Ni DC+ 50-80 80-110 100-140
- WEARSHIELD® ABR DC+ - 50-150 50-185
BLUE MAX® 308/308L AC-DC
SHEET THICKNESS THINNER 1/8 AND THICKER
NOTE: You can supply multiple loads as long as the total load does
not exceed 5700 Peak watts or 5200 continuous watts. Be sure to start the largest loads first.
CURRENT RANGE (AMPS)
3/32 SIZE 1/8 SIZE 5/32 SIZE
DC+ 50-80 75-110 95-150
1/8 AND
OUTBACK™ 185
Page 22
B-8
®
OPERATION
TABLE B.3
AUXILIARY POWER APPLICATIONS
Suggested Power Applications Running Watts *Start-up Watts
(Continuous) (Peak)
*Air Compressor - 1 HP 2,000 4,000 - 8,000
*Air Compressor - 3/4 HP 1,250 3,100 - 5,000
*Airless Sprayer - 1/3 HP 600 1,500 - 2,400
Chain Saw 1,200
Circular Saw 1,200
Coffee Maker 1,000
*Deep Freezer 500 750 - 2,000
*Electric Motor - 1 HP 1,000 2,500 - 4,000
Electric Range (1 element) 1,500
Electric Skillet 1,250
*Furnace Fan - 1/3 HP 1,200 3,000 - 4,800
Portable Grinder (4 1/2”) 600
Portable Grinder (7”) 2,000
Halogen Work Light 500
Hand Drill - 1/4” 500
Hand Drill - 3/8” 700
1500 Watt Heater 1,750
Hedge Trimmer 450
Light Bulb 100
Reciprocating Saw 900
Radial Arm Saw 2,600
Radio 50
*Refrigerator/Freezer (small) 600 1,500 - 2,400
Slow Cooker 200
*Submersible Pump - 1 HP 1,000 2,500 - 4,000
*Sump Pump 600 1,500 - 2,400
Toaster 1,100
Weed Trimmer 500
Lincoln Wire Feeder/Welder 4,000
B-8
NOTES:
Wattages listed are approximate. Check your equipment for actual wattage.
Equipment with unusually high *START-UP WATTS are listed. For start-up of other equipment that uses a motor, listed in the table, multiply RUNNING WATTS by 2.
Multiple loads can be used as long as the total load does not exceed 5,700 Peak watts. Be sure to start the largest loads first.
OUTBACK™ 185
Page 23
C-1
®
ACCESSORIES
OPTIONS/ACCESSORIES
The following options/accessories are available for your OUTBACK™185 from your local Lincoln Distributor:
Accessory Kit (K875) – Includes the following:
• Twenty feet (6.1 meters) of #6 AWG electrode cable with lug.
• Fifteen feet (4.6 meters) of #6 work cable with lugs.
• Work Clamp
• Headshield with No. 10 filter
• Insulated electrode holder and sample electrodes 150 amp capacity.
Undercarriage (K2722-1) - A two-wheeled, hand movable undercarriage is available for field installa­tion.
Rotor Removal Kit (S20925) - A service kit with thru bolt and impact boltʼs for removing the generator rotor from tapered engine crank shaft.
C-1
Spark Arrestor Kit (K2793-1) - Attaches to muffler exhaust tube. Virtually eliminates spark emissions.
Canvas Covers (K2804-1) - To protect the Outback 185 when not in use. Made from attractive red canvas which is flame retardant, mildew resistant and water repellent.
OUTBACK™ 185
Page 24
D-1
®
MAINTENANCE
SAFETY PRECAUTIONS
WARNING
• Have qualified personnel do all maintenance and troubleshooting work.
• Turn the engine off before working inside the machine.
• Remove guards only when necessary to perform maintenance and replace them when the mainte­nance requiring their removal is complete.
• If guards are missing from the machine, get replace­ments from a Lincoln Distributor. See the EXPLOD­ED VIEW AND PARTS LIST at the back of this manual.
------------------------------------------------------------------------
D-1
OIL: Check the oil level after every 5
hours of operation or daily. BE SURE
TO MAINTAIN THE OIL LEVEL. Change the oil the first time after 20 hours of opera­tion. Then, under normal operating conditions, change the oil after every 100 hours or once a year, whichever occurs first. If the engine is operated under heavy load or in high ambient temperatures, change the oil every 50 hours.
Drain the oil from the drain plug located on either side of the engine bottom, as shown in Figure D.1. Refill through the oil fill plug until the oil reaches the full mark on the dip stick. See Engine Ownerʼs manual for specific oil recommendations.
FIGURE D.1 - OIL DRAIN AND
REFILL LOCATION
dipstick - recheck
dipstick to check oil Do not screw in
L I O
FILL to FULL mark on
Read the Safety Precautions in the front of this manu­al and in the Kohler Operating and Maintenance Instructions manual before working on the OUT-
BACK™185 Keep all equipment safety guards, cov­ers, and devices in position and in good repair. Keep your hands, hair, clothing, and tools away from the recoil housing, fans, and all other moving parts when starting, operating, or repairing this machine.
ROUTINE AND PERIODIC MAINTENANCE
ENGINE MAINTENANCE
CAUTION
To prevent the engine from accidentally starting, dis­connect the spark plug lead before servicing the engine.
------------------------------------------------------------------------
See the Kohler Ownerʼs manual for a summary of maintenance intervals for the engine. Follow either the hourly or the calendar intervals, whichever come first. More frequent service may be required, depending on your specific application and operating conditions. The Kohler Ownerʼs manual shows engine maintenance replacement parts and numbers.
OIL
Do not screw in
dipstick to check oil
firmly before starting Tighten dipstick
Tighten dipstick
FILL to FULL mark on
dipstick - recheck
Oil drain
PLUG OIL DRAIN
plug Drain
HEX 12 mm
12 mm
HEX
Drain
plug
Oil drain
OIL DRAIN
PLUG
firmly before starting
FUEL: At the end of each dayʼs use, refill the fuel tank to minimize moisture con­densation and dirt contamination in the fuel line.
AIR CLEANER: With normal operating conditions, the maintenance schedule for cleaning and re-oiling the foam pre-filter is every 50 hours and replacement of the
air cleaner filter element every 100 hours. More frequent servicing is required with dusty operat­ing conditions. Refer to the maintenance section of the Engine Ownerʼs Manual for more information.
OUTBACK™ 185
Page 25
D-2
®
MAINTENANCE
D-2
To service the pre-cleaner:
Remove the cover. Carefully remove the foam pre­cleaner from the filter element.
1. Wash in liquid detergent and water.
2. Squeeze dry in a clean cloth.
3. Saturate in clean engine oil.
4. Squeeze in a clean, absorbent cloth to remove all excess oil.
Carefully place the pre-cleaner back over the filter ele­ment and reinstall the air cleaner cover and wing nuts.
CLEAN ENGINE: Remove dirt and debris with a cloth or a brush. Do not clean with a forceful spray of water. Water might contaminate the fuel system. Use low pressure air to blow out the machine periodically. In particularly dirty locations this may be required once a week.
SPARK PLUG SERVICE
To service spark plug, remove the 9 screws securing the side panel. Remove side panel and place provided fiber spacer between the muffler and bottom of control panel. See Figure D.2.
SLIP RINGS
CAUTION
A slight amount of darkening and wear of the slip rings and brushes is normal. Brushes should be inspected when a general overhaul is necessary. If brushes are to be replace, clean slip rings with a fine emery paper. Do not attempt to polish slip rings while engine is running.
------------------------------------------------------------------------
HARDWARE
Both English and Metric fasteners are used in this welder.
ENGINE MAINTENANCE PARTS
Kohler CS 12.75
Air Filter Element 63 083 19-S
Air Filter Pre-Cleaner 63 083 17-S
Spark Plug Champion RC 12YC
(Resistor Type) (Gap .030” [.76mm])
FIGURE D.2
ENGINE ADJUSTMENTS
OVERSPEED IS HAZARDOUS - The maximum
WARNING
allowable high idle speed for this machine is 3750 RPM, no load. Do NOT tamper with the governor components or setting or make any other adjustments to increase the maximum speed. Severe personal injury and damage to the machine can result if operated at speeds above maximum.
------------------------------------------------------------------------
Adjustments to the engine are to be made only by a Lincoln Service Center or an authorize Field Service Shop.
OPERATIONAL CLEARANCE
CAUTION
Approximately 12-18” of clearance should be around this unit during operation for air flow. Reducing this clearance will reduce air flow to the machine causing operational temperatures to increase. Possible damage to the machine can result if to much air flow is restricted.
------------------------------------------------------------------------
OUTBACK™ 185
Page 26
®
E-1
TROUBLESHOOTING
HOW TO USE TROUBLESHOOTING GUIDE
WARNING
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
E-1
This Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMP­TOMS)”. This column describes possible symptoms that the machine may exhibit. Find the listing that best describes the symptom that the machine is exhibiting.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists the obvious external possibilities that may contribute to the machine symptom.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the Possible Cause, generally it states to contact your local Lincoln Authorized Field Service Facility.
If you do not understand or are unable to perform the Recommended Course of Action safely, contact your local Lincoln Authorized Field Service Facility.
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
OUTBACK™ 185
Page 27
E-2
®
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
TROUBLESHOOTING
POSSIBLE
CAUSE
OUTPUT PROBLEMS
E-2
RECOMMENDED
COURSE OF ACTION
Major Physical or Electrical Damage is Evident.
No Generator power or welding output
Generator power is available but unit will not weld.
1. Contact your local Lincoln Authorized Field Service Facility.
1. Check brushes for wear. See
Maintenance section.
2. Check for loose or faulty
connections at brush holders.
3. Open lead in flashing or field
circuit.
4. Rheostat (R1) lead broke.
5. Dirty slip rings.
6. Faulty rheostat (R1).
7. Faulty field bridge rectifier (D1).
8. Faulty field capacitor (C1).
9. Faulty stator field winding.
10. Faulty rotor.
1. Loose connector to output stud.
2. Work not connected.
3. Electrode holder loose.
4. No open circuit voltage at output studs. Open lead in weld circuit.
5. Faulty output bridge rectifier.
6. Faulty choke (L1).
If all recommended possible areas of misadjustment have been checked and the problem persists,
Contact your local Lincoln Authorized Field Service Facility.
Unit will weld but low or no generator power is available.
No auxillary power but machine has weld output.
1. Circuit breaker is open.
2. Loose or open connection with electrical plug-in component.
3. Current control dial not at “MAX”
4. No open circuit voltage at receptacle.
1. Check CB1 and CB2 - Reset if tripped.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
OUTBACK™ 185
Page 28
E-3
®
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
E-3
PROBLEMS
(SYMPTOMS)
Engine will not idle down to low speed.
Engine idles down to low idle but will not stay at low idle.
Engine will not go to high idle when attempting to weld or use generator power.
POSSIBLE
CAUSE
ENGINE PROBLEMS
1. Engine Switch on HIGH Idle.
2. Engine choke is not fully open.
3. External load on welder or auxiliary power. - Remove load.
4. Machine output is under load or
Engine switch in wrong position.
5. Idle solenoid does not pull in.
1. Engine low idle RPM may be set
too low. - Contact Lincoln Field Service Facility.
1. Check Work and Electrode
cables for loose or faulty con­nections.
2. Mechanical linkage from sole-
noid to engine stuck.
3. Open connection in weld circuit.
4. No output from receptacles or
load too small.
5. Idler pc board is not sensing
output current.
6. Faulty idler pc board.
RECOMMENDED
COURSE OF ACTION
If all recommended possible areas of misadjustment have been checked and the problem persists,
Contact your local Lincoln Authorized Field Service Facility.
Engine will not go to high idle when using auxiliary power.
Engine runs erratic or stops running or engine surges at low idle.
Recoil starter is hard to pull.
Engine will not start or starts but runs rough with low power.
1. Auxiliary load less than 100
watts.
2. Circuit breaker CB1 or CB2
tripped or faulty.
3. Mechanical linkage from sole-
noid to engine stuck.
1. Oil level may be low activating
the engine “Oil Gard” shutdown system. - Check oil level.
2. Idle solenoid linkage or engine
idle misadjusted.
1. Crankcase may be over-filled
with oil. - Check oil level.
1. Water in engine from rain and / or
condensation. - Remove spark plug and dry it if wet. Blow low pressure compressed air in spark plug port while pulling recoil starter. Re-install spark plug.
2. Spark plug may be faulty.
3. Air filter element saturated with
water and / or oil - Replace.
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
OUTBACK™ 185
Page 29
E-4
®
PROBLEMS
(SYMPTOMS)
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
POSSIBLE
CAUSE
WELDING PROBLEMS
RECOMMENDED
COURSE OF ACTION
E-4
Engine runs erratically or stops running.
Engine sputters but will not start.
Recoil starter is hard to pull.
Arc is erratic and “pops out”.
Arc becomes “Cold” at the short Arc lenghts or shorts to the work piece.
1. Engine is not fully warmed-up and engine choke is in the fully open (RUN) position.
2. Engine requires service to head, carburetor, filters, oil spark plug and / or gas.
3. Oil level to low.
1. Bad gas, bad filter, air cleaner, spark plug, and / or breather.
1. Too much oil in crankcase.
1. Check Work and Electrode cables for loose or faulty connection.
2. Electrode may be wet.
1. Reset circuit breaker (CB4)
located under the Current Control Dial on the bottom side of the control panel.
If all recommended possible areas of misadjustment have been checked and the problem persists, Contact
your local Lincoln Authorized Field Service Facility.
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
OUTBACK™ 185
Page 30
F-1
®
DIAGRAMS
F-1
OUTBACK™ 185
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the
machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
Page 31
F-2
®
DIMENSION PRINT
AND EMPTY FUEL TANK.
NOTES:
N.A. CENTER OF GRAVITY WITH OIL IN ENGINE
17.50
21.60
14.17
25.62
6.75
7.79
29.00
31.47
13.50
M21768
8.25 N.A.
B
N.A.
8.25
F-2
B
M21768
13.50
14.17
7.79
31.47
29.00
6.75
25.62
17.50
AND EMPTY FUEL TANK.
NOTES:
N.A. CENTER OF GRAVITY WITH OIL IN ENGINE
OUTBACK™ 185
21.60
Page 32
NOTES
®
OUTBACK™ 185
Page 33
WARNING
Spanish
AVISO DE
PRECAUCION
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
Japanese
Chinese
G Do not touch electrically live
parts or electrode with skin or wet clothing.
G Insulate yourself from work
and ground.
G No toque las partes o los elec-
trodos bajo carga con la piel o ropa mojada.
G Aislese del trabajo y de la tier-
ra.
G Ne laissez ni la peau ni des
vêtements mouillés entrer en contact avec des pièces sous tension.
G Isolez-vous du travail et de la
terre.
G Berühren Sie keine strom-
führenden Teile oder Elektroden mit Ihrem Körper oder feuchter Kleidung!
G Isolieren Sie sich von den
Elektroden und dem
G Keep flammable materials
away.
G Mantenga el material com-
bustible fuera del área de tra­bajo.
G Gardez à lʼécart de tout
matériel inflammable.
G Entfernen Sie brennbarres
Material!
G Mantenha inflamáveis bem
G Wear eye, ear and body pro-
tection.
G Protéjase los ojos, los oídos y
el cuerpo.
G Protégez vos yeux, vos
oreilles et votre corps.
G Tragen Sie Augen-, Ohren-
und Kör-perschutz!
G Use proteção para a vista,
ouvido e corpo.
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURERʼS INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYERʼS SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRO­DENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS
Page 34
G Keep your head out of fumes. G Use ventilation or exhaust to
remove fumes from breathing zone.
G Los humos fuera de la zona de
respiración.
G Mantenga la cabeza fuera de
los humos. Utilice ventilación o aspiración para gases.
G Gardez la tête à lʼécart des
fumées.
G Utilisez un ventilateur ou un
aspirateur pour ôter les fumées des zones de travail.
G Vermeiden Sie das Einatmen
von Schweibrauch!
G Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
G Mantenha seu rosto da
fumaça.
G Turn power off before servic-
ing.
G Desconectar el cable de ali-
mentación de poder de la máquina antes de iniciar cualquier servicio.
G Débranchez le courant avant
lʼentretien.
G Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öffnen; Maschine anhalten!)
G Não opere com as tampas
removidas.
G Do not operate with panel
open or guards off.
G No operar con panel abierto o
guardas quitadas.
G Nʼopérez pas avec les pan-
neaux ouverts ou avec les dis­positifs de protection enlevés.
G Anlage nie ohne
Schutzgehäuse oder Innenschutzverkleidung in Betrieb setzen!
G Mantenha-se afastado das
partes moventes.
G Não opere com os paineis
WARNING
Spanish
AVISO DE
PRECAUCION
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
Page 35
®
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Loading...