Lincoln Town Car 2010 User Manual

Download

Introduction 4

Instrument Cluster 12

Warning lights and chimes 12 Gauges 16 Message center 18

Entertainment Systems 26

AM/FM stereo cassette with CD 26 AM/FM stereo with in-dash six CD 31

Climate Controls 38

Dual automatic temperature control 38 Rear window defroster 41

Lights 42

Headlamps 42 Turn signal control 46 Bulb replacement 46

Driver Controls 53

Windshield wiper/washer control 53 Steering wheel adjustment 54 Power windows 57 Mirrors 58 Speed control 60

Locks and Security 77

Locks 77 Anti-theft system 89

Seating and Safety Restraints 95

Seating 95 Safety restraints 103 Airbags 116 Child restraints 129

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Table of Contents

Tires, Wheels and Loading 148

Tire information 148 Tire inflation 150 Tire Pressure Monitoring System (TPMS) 163 Vehicle loading 168 Trailer towing 175 Recreational towing 178

Driving 179

Starting 179 Brakes 184 Traction Control™ 186 Air suspension 188 Transmission operation 190 Reverse sensing system 193

Roadside Emergencies 197

Getting roadside assistance 197 Hazard flasher control 198 Fuel pump shut-off switch 199 Fuses and relays 199 Changing tires 206 Wheel lug nut torque 214 Jump starting 215 Wrecker towing 220

Customer Assistance 222

Reporting safety defects (U.S. only) 228 Reporting safety defects (Canada only) 228

Cleaning 229

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Table of Contents

Maintenance and Specifications 236

Engine compartment 238 Engine oil 240 Battery 243 Engine coolant 245 Fuel information 251 Air filter(s) 267 Maintenance product specifications and capacities 269 Engine data 272

Accessories 275

Ford Extended Service Plan 277

Index 280

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

CONGRATULATIONS

Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Mexico: www.ford.com.mx

• In Australia: www.ford.com.au

Additional owner information is given in separate publications.

This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.

Remember to pass on the Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.

WARNING: Fuel pump shut-off switch: In the event of an

accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter.

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

Warning symbols on your vehicle

When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.

Protecting the environment

We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

PERCHLORATE MATERIAL

Certain components of this vehicle such as airbag modules, seat belt pretensioners, and button cell batteries may contain Perchlorate Material – Special handling may apply for service or vehicle end of life disposal. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. Vary your speed frequently in order to give the moving parts a chance to break in.

Drive your new vehicle at least 1,000 miles (1,600 km) before towing a trailer. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter.

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide/Customer Information Guide that is provided to you along with your Owner’s Guide.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints

chapter. Failure to follow the specific warnings and instructions could result in personal injury.

WARNING: Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

DATA RECORDING

Service Data Recording

Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle. For U.S. only (if equipped), if you choose to use the SYNC威 Vehicle Health Report, you consent that certain diagnostic information may also be accessed electronically by Ford Motor Company and Ford authorized service facilities, and that the diagnostic information may be used for any purpose. See your SYNC威 supplement for more information.

Event Data Recording

Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event. The modules may record information about both the vehicle and the occupants, potentially including information such as:

• how various systems in your vehicle were operating;

• whether or not the driver and passenger seatbelts were

buckled;

• how far (if at all) the driver was depressing the accelerator

and/or the brake pedal;

• how fast the vehicle was traveling;

• where the driver was positioning the steering wheel; and

• longitude and latitude of vehicle at last location, using GPS

technology and advanced vehicle sensors.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada. To the extent that any law pertaining to Event Data Recording applies to SYNC威 or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911 Assist may, through any paired and connected cell phone, disclose to emergency services that the vehicle has been in a crash involving the deployment of an airbag or, in certain vehicles, the activation of the fuel pump shut-off. Certain versions or updates to 911 Assist may also be capable of electronically or verbally disclosing to 911 operators the vehicle location, and/or other details about the vehicle or crash to assist 911 operators to provide the most appropriate emergency services. If you do not want to disclose this information, do not activate the feature. See your SYNC威 supplement for more information. Additionally, when you connect to Traffic, Directions and Information (if equipped, U.S. only), the service uses GPS technology and advanced vehicle sensors to collect the vehicle’s current location, travel direction, and speed (“vehicle travel information”) only to help provide you with the directions, traffic reports, or business searches you request. If you do not want Ford or its vendors to receive this information, do not activate the service. Ford Motor Company and the vendors it uses to provide you with this information do not store your vehicle travel information. For more information, see Traffic, Directions and Information, Terms and Conditions. See your SYNC威 supplement for more information.

CELL PHONE USE

The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.

Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in-vehicle communications systems, telematics devices and portable two-way radios.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

WARNING: Driving while distracted can result in loss of vehicle

control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’s primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION

For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’s Guide. A market unique supplement may be supplied that complements this book. By referring to the market unique supplement, if provided, you can properly identify those features, recommendations and specifications that are unique to your vehicle. This Owner’s Guide is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for Export. Refer to this Owner’s Guide for all other required

information and warnings.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Airbag - Front

Airbag - Side

Child Seat Tether Anchor

Anti-Lock Brake System Parking Brake System

Brake Fluid Non-Petroleum Based

Stability Control System Speed Control

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower Anchor

Brake System

Parking Aid System

Fuel Pump Reset Windshield Wash/Wipe

Windshield Defrost/Demist

Rear Window Defrost/Demist

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Vehicle Symbol Glossary

Introduction

Power Windows Front/Rear

Child Safety Door Lock/Unlock

Power Window Lockout

Interior Luggage Compartment Release

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames, or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid Level

Service Engine Soon Engine Air Filter

MAX

MIN

Passenger Compartment Air Filter

Check Fuel Cap

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Jack

Low Tire Pressure Warning

Instrument Cluster

WARNING LIGHTS AND CHIMES

Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information.

Service engine soon: The Service engine soon indicator light

illuminates when the ignition is first turned to the on position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the ⬙Service engine soon⬙ light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the ⬙Service engine soon⬙ light blinks eight times, it means that the vehicle is not ready for I/M testing. See the Readiness for Inspection/Maintenance (I/M) testing in the Maintenance and Specifications chapter.

Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately by your authorized dealer.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

WARNING: Under engine misfire conditions, excessive exhaust

temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the on position when the engine is not running, or in a position between on and start, or by applying the parking brake when the ignition is turned to the on position. If the brake system warning light does not illuminate at this time, seek service immediately from your authorized dealer. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your authorized dealer.

WARNING: Driving a vehicle with the brake system warning

light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your authorized dealer. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer. Normal braking is still functional unless the brake warning light also is illuminated.

Airbag readiness: If this light fails to illuminate when the ignition is turned to no, continues to flash or remains on, have the system serviced immediately by your authorized dealer. A chime will sound when there is a malfunction in the indicator light.

BRAKE

ABS

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Safety belt: Reminds you to fasten your safety belt. A Belt-Minder威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder威 chime feature.

Charging system: Illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a related component.

Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter.

Traction Control (if equipped):

Flashes when the traction control system is active. It will be illuminated solidly if there is a fault with the system and traction control will be disabled. Have the system serviced immediately. Refer to the Driving chapter for more information.

Severity indicator: Displays the indicated severity color when any of the following warning conditions has occurred:

• Red: Low Oil Pressure, Charge System, Engine Coolant Over Temperature, Door Ajar

• Amber: Low Fuel

Refer to Message center in this chapter.

Low tire pressure warning (if equipped): Illuminates when your

tire pressure is low. If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating your tires in the Tires, Wheels and

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Loading chapter. When the ignition is first turned to on, the light will illuminate for three seconds to ensure the bulb is working. If the light does not turn on, have the system inspected by your authorized dealer. For more information on this system, refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter.

O/D off: Illuminates when the overdrive function of the transmission has been turned off; refer to the Driving chapter. If the light does not illuminate, have the transmission serviced soon, or damage may occur.

Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.

Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.

High beams: Illuminates when the high beam headlamps are turned on.

O/D

OFF

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened.

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’s door is opened.

Turn signal chime (if equipped): Sounds when the turn signal lever has been activated to signal a turn and not turned off after the vehicle is driven more than 1/2 mile (0.8 km).

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

GAUGES

Speedometer: Indicates the current vehicle speed. Refer to the Message center in this chapter to change your display to a digital speedometer. The digital display is more accurate than the analog gauge and may not match.

Engine coolant temperature gauge: Indicates engine coolant

temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section,

the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool, refer to

What you should know about fail-safe cooling in the Maintenance and Specifications chapter.

WARNING: Never remove the coolant reservoir cap while the engine is running or hot.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Odometer: Registers the total miles (kilometers) of the vehicle.

Refer to Message center in this chapter on how to switch the display from Metric to English and the odometer to the speedometer.

Trip odometer: See TRIP A/B under Message center in this chapter.

Hour meter (if equipped): Your vehicle may be equipped with an hour meter to indicate how much time the vehicle is idling in Park or Neutral. The meter is incorporated with the vehicle odometer. Press and release the message center INFO button until “ENGINE IDLE 0 HOURS” appears in the display. Press the RESET button to reset. For every hour that the vehicle idles, it has accumulated the equivalent of approximately 33 miles (53 km) of driving. Using the combination of the vehicle odometer and hour meter allows the fleet manager to better determine when the oil needs to be changed.

Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.

The arrow near the fuel pump icon indicates which side of the vehicle the fuel filler door is located.

Refer to Filling the tank in the Maintenance and Specifications chapter for more information.

MESSAGE CENTER

With the ignition in the on position, the message center, located on your instrument cluster, displays important vehicle information

through a constant monitor of vehicle systems. You may select

display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

Your display can show up to three reconfigurable telltales at one time. What ever is displayed in the top left corner has the highest priority. Premium Display Severity Indicator (located under the message center): Indicates severity of the information being displayed on the premium display. Red for high severity, amber for medium severity, and non-lit for information only. For example, a door ajar warning would be accompanied by a red indicator, low fuel by an amber indicator, and fuel economy by an absence of the indicator. The indicator always illuminates with the highest severity rating of the warnings displayed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Info (Information menu)

Press the INFO button repeatedly to cycle through the following features listed:

Press the RESET button reset functions in the information menu.

TRIP A/B

Registers the distance of individual journeys. Press and release INFO button until the A or B trip appears in the display (this represents the trip mode). Press and hold the RESET button for two seconds to reset.

Refer to UNITS later in this section to switch the display from Metric to English.

MILES (km) TO EMPTY

This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel.

The DTE function will display FUEL LEVEL LOW and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes or 10 miles (16 km).

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.

AVERAGE FUEL XX.X MPG (L/100km)

Average fuel economy displays your average fuel economy in miles/gallon or liters/100 km.

If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons:

• Your vehicle was not perfectly level during fill-up 19

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

• Differences in the automatic shut-off points on the fuel pumps at service stations

• Variations in top-off procedure from one fill-up to another

• Rounding of the displayed values to the nearest 0.1 gallon (liter)

1. Drive the vehicle at least 5 miles (8 km) with the speed control

system engaged to display a stabilized average.

2. Record the highway fuel economy for future reference.

It is important to press the RESET control (press and hold RESET for two seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings.

FUEL ECONOMY MPG (L/km)

This displays instantaneous fuel economy as a bar graph ranging from ↓ poor economy to ↑ excellent economy.

Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows ↓, one or no bars illuminated. Instantaneous fuel economy cannot be reset.

TIMER

Timer displays the trip elapsed drive time. To operate, do the following:

1. Press and release RESET in order to start the timer.

2. Press and release RESET to pause the timer.

3. Press and hold RESET until the timer resets.

System Check and Vehicle Feature Customization

Press the SETUP button repeatedly to cycle the message center through the following features listed:

Press SELECT to select functions in the setup menu:

PRESS SELECT TO BEGIN SYSTEM CHECK

When this message appears, press SELECT and the message center will begin to cycle through the following systems and provide a status of the item if needed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Note: Some systems show a message only if a condition is present.

1. OIL LIFE — HOLD RESET IF NEW OIL

2. WASHER FLUID

3. AIR SUSPENSION (if equipped)

4. RECONFIGURABLE TELLTALES —OK — FAILED RED — FAILED AMBER

5. PARK AID (if equipped)

SCREEN FORM

Press SELECT to change the display:

• ODOMETER

• SPEEDO

TEXT SIZE

Press SELECT to change the display text size:

• NORMAL

• LARGE

UNITS

Displays the current units English or Metric. Press SELECT to change the display units.

• ENGLISH

• METRIC

LANGUAGE

Displays the current language selected. Press SELECT to change the display language.

• ENGLISH

• ESPANOL

• FRANCAIS

COMPASS

The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration

adjustment.

Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment.

Compass zone/calibration adjustment

1. Determine your magnetic zone by

referring to the zone map.

2. Turn ignition to the on position.

3. Start the engine.

4. Press SETUP to reach the

Compass/Odometer function.

5. Press SELECT to show COMPASS

ZONE <XX> PRESS SELECT TO CHANGE.

6. Press the SELECT control

repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 01 to 15 and “wraps” back to 01.

7. To exit the zone setting mode, and to “lock in” your change, press and

release the SETUP control. Perform compass calibration in an open area free from steel structures

and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.

8. Press the SELECT control to start the compass calibration function.

9. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until

the CIRCLE SLOWLY TO CALIBRATE COMPASS display changes to COMPASS CALIBRATION COMPLETED. It will take up to five circles to complete calibration.

123

6 7 8 9 1011

14 13

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

10. The compass is now calibrated.

OIL LIFE START VALUE PRESS SELECT TO CHANGE

Press SELECT to change the oil life start value. OIL LIFE START VALUE SET TO XXX% will be displayed.

To reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or six months), perform the following:

1. Press and hold the RESET control for two seconds and release. Oil life is set to 100% and “OIL LIFE XXX% HOLD RESET IF NEW OIL” is displayed.

2. Press and hold the RESET control for three seconds and release. Oil life is set to 100% and “OIL LIFE START VALUE SET TO XXX%” is displayed.

PARK AID (Reverse sensing system–if equipped)

This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected.

1. Before you disable/enable the reverse sensing system feature, put the vehicle in R (Reverse).

2. Press RESET to turn the park aid ON or OFF.

System warnings

System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems.

In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds.

The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.

Warning messages that have been reset are divided into three categories:

• They cannot be reset until the condition is corrected.

• They will reappear on the display 10 minutes from the reset.

• They will not reappear until an ignition off-on cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

DOOR AJAR — Displayed when a door is not completely closed. POWERTRAIN MALFUNCTION — Displayed when the powertrain is

not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

COOLANT OVER TEMPERATURE — Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

WARNING: Never remove the coolant reservoir cap while the engine is running or hot.

CHECK FUEL CAP — Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter.

CHECK AIR SUSPENSION — Displayed when the air suspension system is not operating properly. If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension system in the Driving chapter.

FUEL LEVEL LOW — Displayed as an early reminder of a low fuel condition. Warning message can be reset by pressing the RESET button, but will return after 10 minutes. If any other button is pressed besides RESET, the message ’’PRESS RESET TO CLEAR’’ will appear in the message center. Once this message disappears (after approximately two seconds), press RESET to clear the warning.

TRUNK AJAR — Displayed when the trunk is not completely closed. OVERDRIVE OFF — Displayed when the overdrive is disabled. OVERDRIVE ON — Displayed when the overdrive is enabled. LOW TIRE PRESSURE — Displayed when one or more tires on your

vehicle have low tire pressure. Refer to Inflating your tires in the Tires, Wheels and Loading chapter.

TIRE PRESSURE MONITOR FAULT — Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Instrument Cluster

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use (Note: this includes the use of the optional full-sized matching spare tire and wheel). For more information on how the system operates under these conditions, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

CHECK COMPASS MOD — Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter.

OIL LIFE CHANGE SOON — Displayed when the engine oil life remaining is 10% or less.

OIL CHANGE REQUIRED — Displayed when the oil life left reaches 0%.

An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

AUDIO SYSTEMS

Premium AM/FM Stereo Single CD/Cassette system

WARNING: Driving while distracted can result in loss of vehicle

Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until any door is opened.

1. CD slot: Insert a CD, label side up. With the ignition on, the radio will begin to play a CD once inserted. If the ignition and audio system are off, press CD prior to inserting a disc. Do not force a disc into the system as damage could result.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

2. CD eject: Press to eject a CD. If the disc is not removed within the allotted time, the system will automatically reload the CD and begin play. Note: The eject function will work when the ignition and audio systems are turned off.

3. BASS: Press BASS; then press

SEL-TEXT to

decrease/increase the level of bass output.

TREB (Treble): Press TREB; then press

SEL-TEXT to

decrease/increase the level of treble output.

4. BAL (Balance): Press BAL; then press

SEL-TEXT to shift

sound to the left/right speakers.

BASS

TREB

BASS

TREB

BAL

FADE

SEL-TEXT

FADE: Press FADE; then press SEL-TEXT

to shift sound to the

rear/front speakers.

BAL

FADE

SEL-TEXT

5. Phone/mute: Press to mute the playing media. Press again to return to the playing media, or turn the volume control to adjust the volume.

6. SEL/TEXT: Use with Bass, Treble, Balance, Fade and other menu functions.

TEXT: TEXT is only available when equipped with Satellite radio. Your radio is equipped with Satellite ready capability. The kit to enable satellite reception is available through your authorized dealer. Detailed satellite instructions are included with the dealer installed kit. Check

with your authorized dealer for availability.

7. MENU: Press MENU repeatedly to access RBDS on/off. Use SEL to turn RBDS ON or OFF. Press MENU again to access Program type mode or Show Type/Name mode. (MENU must be pressed within 10 seconds to proceed to the next RBDS mode.)

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RBDS technology to transmit information. FM radio stations are independently operated and individually elect to use RBDS technology to transmit station ID and program type as desired.

FIND Program type: Allows you to search RBDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40. With RBDS ON, press MENU until the program type menu is displayed.

One of the various program types will appear. Press to scroll through music types. Press SEEK or SCAN to search for a

station playing the requested music category. Show TYPE: Selects between displaying the station’s call letters or

music format when RBDS is enabled. Press MENU until SHOW XX appears in the display. Press TYPE.

Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU repeatedly until

COMP (compression) is displayed. Press the compression feature when COMPRESS OFF is displayed. Press ON is displayed. When activated, the compression icon will appear in the

display. Occupancy mode: (if equipped): Press MENU repeatedly until

occupancy mode appears in the display. Press select ALL, DRIVER or REAR SEAT occupancy mode.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. Press MENU repeatedly until AUTOSET appears in the display.

Press stations are filled, the station stored in preset 1 will begin playing. If

there are less than six strong stations, the system will store the last one in the remaining presets.

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. SPEED OFF turns the feature off and level 7 is the maximum setting.

Press MENU to access and setting. The level will appear in the display. 28

SEL-TEXT again to disable the feature when COMPRESS

SEL-TEXT to turn ON or OFF. When the six strongest

SEL-TEXT to select NAME or

SEL-TEXT to enable

SEL-TEXT to adjust the volume

SEL-TEXT

SEL-TEXT to

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

Dolby: Works in tape mode to reduces tape noise and hiss. Press MENU until DOLBY XX appears in the display. Press SEL/TEXT to turn ON or OFF. The Dolby威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby威 and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation.

Armrest (if equipped): If your vehicle is equipped with Rear Seat Audio controls, this feature will be listed in Menu mode.

Press ON, rear seat passengers can adjust the settings of the front audio stem.

For further information, refer to Rear Console Audio Controls (if equipped) later in this chapter.

Note: The menu selections will remain in the display for approximately 10 seconds, at which time the display will return to the previous mode. You may also exit the menu options by pressing any other audio control.

Setting the clock: Your vehicle is equipped with a separate in-dash clock. Refer to Clock in the Driver Controls chapter for instructions on how to set the time.

8. Cassette: Insert a cassette facing to the right.

9. TUNE: Press to manually go up or down the radio frequency.

SEL-TEXT to turn ON or OFF. When the feature is turned

CAT: CAT is only available when equipped with Satellite Radio. Your vehicle may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your authorized dealer. Detailed Satellite instructions are included with the dealer installed kit.

Check with your authorized dealer for availability.

10. Side 1–2: Press to access the next side of the cassette tape. The display will indicate whether TAPE 1orTAPE2isplaying.

11. SEEK: Press to access the next/previous radio station, tape selection or CD track. Press and hold to advance/reverse in the current CD track.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

12. REW (Rewind): Press to rewind in tape or CD mode.

REW

FF (Fast forward): Press to fast forward in tape or CD mode.

13. SCAN: Press SCAN to hear a brief sampling of radio stations, selections or CD tracks. Press again to stop.

14. SHUF (Shuffle): Press to play the tracks on the current CD in random order. Press again to stop.

15. Memory presets: To set a station: Select frequency band, tune to a station, press and hold a preset button until sound returns.

16. AM/FM: Press to switch between AM/FM1/FM2 modes.

17. Tape eject: Press to eject the tape.

18. CD/TAPE: Press to switch between CD and TAPE mode. In radio mode, the CD icon will appear in the display if a CD is loaded into the system.

19. SAT: Your system may be equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your authorized dealer. Detailed satellite instructions are included with the dealer installed kit.

Check with your authorized dealer for availability.

20. On/Off/Volume: Press to turn on and off; turn to adjust the volume levels.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

Premium plus AM/FM Stereo In-dash Six CD sound system

WARNING: Driving while distracted can result in loss of vehicle

Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to ten minutes after the ignition is turned off or until any door is opened.

1. CD slot: To insert a CD, press LOAD. Wait to insert a CD until the system prompts you. With the ignition on, the radio will begin to play a CD once inserted. If the ignition and audio system are off, press CD prior to inserting a disc. Do not force a disc into the system as damage could result.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

2. SEEK: Press to access the next/previous radio station or CD track. Press and hold to advance/reverse in the current CD track.

3. TUNE/CAT: Press to manually go up or down the radio frequency.

CAT is only available when equipped with Satellite radio. Your vehicle may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your authorized dealer. Detailed Satellite instructions are included with the dealer installed kit. Check with your authorized dealer for

availability.

4. MUTE: Press to mute the playing media. Press again to return to the playing media or turn the volume control to adjust the volume.

5. Eject: Press to eject CD(s) when the ignition is on or off. Numbers will illuminate in the display indicating which CD slots are loaded with CDs. To eject a specific CD, press eject and the corresponding preset number. If no preset is selected, the system will eject the currently selected CD. Press and hold to eject all loaded discs.

Note: If the CD is not removed within approximately 15 seconds, the system will reload the disc and begin play if the system is on.

6. BASS: Press BASS; then press

SEL-TEXT to

decrease/increase the level of bass output.

TREB (Treble): Press TREB; then press

SEL-TEXT to

decrease/increase the level of treble output.

7. BAL (Balance): Press BAL; then press

SEL-TEXT to shift

sound to the left/right speakers.

BASS

TREB

BASS

TREB

BAL

FADE

SEL-TEXT

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

FADE: Press FADE; then press

SEL-TEXT to shift

sound to the rear/front speakers.

BAL

FADE

SEL-TEXT

8. SEL-TEXT: Use with Bass, Treble, Balance, Fade and other menu functions.

TEXT: TEXT is only available when equipped with Satellite radio. Your vehicle may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your authorized dealer. Detailed Satellite instructions are included with the dealer installed kit. Check

with your authorized dealer for availability.

9. MENU: Press MENU repeatedly to access RBDS ON or OFF.

Use

SEL-TEXT to turn

RBDS ON or OFF. Press MENU again to access Program type mode or Show Type mode. (MENU must be pressed within 10 seconds to proceed to the next RBDS mode.)

FIND Program type: Allows you to search RBDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40. In FM mode, with RBDS ON, press MENU until the program type menu is displayed. One of the various program types will appear.

Press

SEL-TEXT to scroll through music types. Press SEEK or

SCAN to search for a station playing the requested music category. Show TYPE: Selects between displaying the station’s call letters or

music format when RBDS is enabled. Press and hold MENU until SHOW XX appears in the display. Press

SEL-TEXT to select NAME or

TYPE. Compression: Brings soft and loud CD passages together for a more

consistent listening level when in CD mode. Press MENU until compression status is displayed. Press

SEL-TEXT to enable the

compression feature when COMPRESS OFF is displayed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

Press SEL-TEXT again to disable the feature when COMPRESS ON is displayed. When activated, the compression icon will illuminate in

the display.

Occupancy mode: (Available on Premium plus audios): Press MENU until occupancy mode appears in the display. Press select ALL, DRIVER or REAR SEAT occupancy mode.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. Press

MENU until AUTOSET appears in the display. Press to turn ON or OFF. When the six strongest stations are filled, the station

stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. When activated, AUTOSET will appear in the display when any of the preset controls are pressed.

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting.

Press MENU to access and use setting. The level will appear in the display.

Armrest ON/OFF: Press MENU repeatedly until Armrest ON/OFF appears. Use ON or OFF (if equipped).

Setting the clock: Your vehicle is equipped with an in-dash clock. Refer to Clock in the Driver Controls chapter for instructions on how to set the time.

10. Memory presets: To set a station: Select frequency band, tune to a station, press and hold a preset button until sound returns.

11. On/Off/Volume: Push to turn on/off; turn to adjust the volume levels.

Note: With the ignition and audio system off, you may press the volume control to momentarily view the clock.

SEL-TEXT to toggle the rear console audio controls

SEL-TEXT to adjust the volume

SEL-TEXT to

SEL-TEXT

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

12. LOAD: Press to load a CD. When the system prompts you, select a preset to load a CD in that particular slot. Load the CD. If you do not pick a slot, the system will select the next available slot. Available slots are indicated by small flashing indicators in the display. Press and hold to autoload up to six discs.

Note: Ensure that the system is ready to accept the CD and do not try to force the disc into the CD slot as damage could result.

13. AM/FM: Press repeatedly to switch between AM/FM1/FM2 mode.

14. CD: Press to enter CD mode. Press CD and a preset to select a specific CD to play.

15. SAT: SAT is only available when equipped with Satellite radio. Your vehicle may be equipped with Satellite ready capability. The kit to enable Satellite reception is available through your authorized dealer. Detailed Satellite instructions are included with the dealer installed kit. Check

with your authorized dealer for availability.

16. SHUF/SCAN: Press SCAN to hear a brief sampling of radio stations or CD tracks. Press again to stop.

SHUF (Shuffle): Press and hold to play the CD tracks in random order for the CD currently being played. Press again to stop.

Rear console audio controls (if equipped)

• NEXT: Press to access the next radio memory preset, the next CD track or the next tape selection.

• VOL: Press the up arrow to increase the volume or the down arrow to decrease the volume.

• MODE: Press to cycle through AM, FM1, FM2, TAPE or CD (if equipped) modes.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

GENERAL AUDIO INFORMATION

Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio

reception:

• Distance/strength: The further you travel from a station, the weaker the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.

• Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

Cassette player care:

• Use only cassettes that are 90 minutes long or less.

• Tighten very loose tapes by inserting a finger or pencil into the hole

and turning the hub.

• Remove loose labels before inserting tapes.

• Allow tapes which have been subjected to extreme heat, humidity or

cold to reach a moderate temperature before playing.

• Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation.

Don’t:

• Expose tapes to direct sunlight, extreme humidity, heat or cold.

• Leave tapes in the cassette player for a long time when not being

played.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Entertainment Systems

CD/CD player care:

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods of time.

• Clean using a circular motion.

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty, warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information.

Audio system warranty and service: Refer to the Warranty

Guide/Customer Information Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Climate Controls

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM

1. A/C control: Cools the vehicle

A/C

and is used to reduce humidity in the vehicle. Press to turn on/off.

The A/C control engages automatically in AUTO,

and modes.

2. Recirculation control: Cools the vehicle more quickly by recirculating the cabin air instead of using outside air and helps prevent unpleasant outside odors or fumes from entering the vehicle. Press to turn on/off in all modes except Recirculation may turn off automatically to reduce fogging potential.

3. Passenger side temperature control: Controls the temperature on the passenger side of the vehicle when in dual zone mode. To enter dual zone, press the passenger temperature control or DUAL. The passenger temperature will appear in the display.

4. Rear defroster control: Removes ice and fog from the rear

window. Press to turn on/off. Refer to the rear window defrost section for more information.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Climate Controls

5. DUAL (Single/dual temperature

DUAL

control): Allows the driver to have full control of the cabin temperature settings (single zone) or allows the passenger to have control of their individual temperature settings (dual zone). Press to turn on dual zone mode, press again to return to single zone.

: Distributes air through the windshield defroster vents and the

side window demisters.

: Distributes air through the windshield defroster vents, the side

window demisters and floor vents.

: Distributes air through the floor vents.

: Distributes air through the instrument panel vents and the floor

vents.

10.

Manual override controls: Allows

: Distributes air through the instrument panel vents.

OFF

you to manually determine where airflow is directed. To return to fully automatic control, press AUTO.

11. OFF: Outside air is shut out and

OFF

the fan will not operate.

12. AUTO: Press and select the

AUTO

desired temperature. The system will automatically determine the fan speed, airflow location, A/C on or off, outside or recirculated air to heat or cool the vehicle to the selected temperature. If unusual conditions exist, (i.e., window fogging, etc.), manual overrides allow you to select airflow locations and fan speed.

13. Driver’s side temperature

control: Controls the temperature on the driver side of the vehicle.

14. Fan Speed: Used to manually

enable or disable the fan speed. To return to automatic fan operation, press AUTO.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Climate Controls

15. EXT: Displays the outside air temperature. It will remain displayed until the EXT control is pressed again. The external temperature will be most accurate when the vehicle has been moving for a period of time.

16. Temperature conversion: Press to switch between Fahrenheit and Celsius temperature on the DEATC display only. The set point temperatures in Celsius will be displayed in half-degree increments.

Operating tips

• To reduce fog build up on the windshield during humid weather, place the air flow selector in the

• To reduce humidity build up inside the vehicle: do not drive with the recirculation control on or the system turned off.

• To improve the A/C cool down, drive with the windows slightly open for 2–3 minutes after start up or until the vehicle has been “aired out.”

• Do not put objects under the front seats that will interfere with the airflow to the back seats.

• Remove any snow, ice or leaves from the air intake area at the base of the windshield.

During extreme high ambient temperatures when idling stationary for extended periods of time in gear, it is recommended to run the A/C in the MAX A/C position, reduce blower fan speed from the highest setting and put the vehicle’s transmission into the PARK gear position to continue to receive cool air from your A/C system.

To aid in side window defogging/demisting in cold weather:

1. Select

2. Select A/C.

3. Adjust the temperature control to maintain comfort.

4. Set the fan to the highest speed.

5. Direct the outer instrument panel vents towards the side windows.

To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

position.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Climate Controls

REAR CONSOLE CLIMATE CONTROLS (IF EQUIPPED)

• TEMP: Press to increase or decrease airflow temperature.

• FAN: Press to increase or decrease the fan speed.

REAR WINDOW DEFROSTER

The rear defroster control is located on the instrument panel.

Press the rear defroster control to clear the rear window of thin ice and fog. A small LED will illuminate when the rear defroster is activated.

The ignition must be in the on position to operate the rear window defroster.

The defroster turns off automatically after a predetermined amount of time or when the ignition is turned off. To manually turn off the defroster, press the control again.

Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines and will not be covered by your warranty.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

HEADLAMP CONTROL

Turns the lamps off.

Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.

Turns the headlamps on.

Autolamp control

The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.

The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to off.

The autolamps are turned on at night or when the front wipers are turned on.

• To turn autolamps on, rotate the control counterclockwise. The

preselected time lapse is adjustable up to approximately three minutes. See the programming procedure following.

• To turn autolamps off, rotate the control clockwise to the off position

(O).

The amount of time the autolamps stay on can be programed by doing the following:

1. Turn the ignition to off.

2. Turn the headlamp switch to the autolamp position. Note: Steps 3 through 5 need to be performed within 10 seconds.

3. Turn the headlamp switch to off.

4. Turn the ignition to on and then back to off.

5. Turn the headlamp switch to the autolamp position.

• At this point, the exterior lamps turn on. 42

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

6. Wait the desired amount of time for delay, then turn the headlamp switch to off.

• At this point, the exterior lamps turn off and the time delay is set.

High beams

Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.

Flash to pass

Pull toward you slightly to activate and release to deactivate.

Daytime running lamps (DRL) (if equipped)

The daytime running light system turns the headlamps on, with a reduced light output, when:

• the ignition is on,

• the transmission is not in P (Park),

• the headlamp system is not turned on by another feature such as

using the headlamp control or Autolamp.

WARNING: Always remember to turn on your headlamps at

dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

PANEL DIMMER CONTROL

Use to adjust the brightness of the instrument panel during headlight and parking lamp operation.

• Rotate the thumbwheel from left to right to brighten the instrument panel.

• Rotate the thumbwheel from right to left to dim the instrument panel.

During full daylight, the instrument panel will still be visible with the headlamps operating.

Dome lamp control

The panel dimmer control also controls the dome lamp operation.

• Rotate the thumbwheel fully to the right, past detent to activate the dome lamp and all interior lamps.

• In order to turn off these lamps, rotate the thumbwheel to the left.

AIMING THE HEADLAMPS

The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer.

Vertical aim adjustment

1. Park the vehicle directly in front of a wall or screen on a level surface,

approximately 25 feet (7.6 meters) away. Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

• (1) 8 feet (2.4 meters)

• (2) Center height of lamp to

ground

• (3) 25 feet (7.6 meters)

• (4) Horizontal reference line

2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).

3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood.

4. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted.

To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other.

5. Locate the vertical adjuster on each headlamp. Usinga4mm wrench, turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up). The horizontal edge of the brighter light should touch the horizontal reference line.

6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE.

7. Close the hood and turn off the lamps.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

TURN SIGNAL CONTROL

• Push down to activate the left turn signal.

• Push up to activate the right turn signal.

INTERIOR LAMPS

Map/courtesy lamps

To turn on the map lamps, press the map lamp control.

Rear courtesy/reading lamps

The courtesy lamp lights when:

• the rocker control is pressed.

• any door is opened.

• any of the remote entry controls

are pressed and the ignition is off.

BULB REPLACEMENT

Lamp assembly condensation

Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions.

Examples of acceptable condensation are:

• Presence of thin mist (no streaks, drip marks or droplets)

• Fine mist covers less than 50% of the lens

Examples of unacceptable moisture (usually caused by a lamp water leak) are:

• Water puddle inside the lamp

• Large water droplets, drip marks or streaks present on the interior of

the lens

Take your vehicle to dealer for service if any of the above conditions of unacceptable moisture are present.

Using the right bulbs

Replacement bulbs are specified in the following chart. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function Trade Number

Headlamp (Hi beam) 9005 Headlamp (Low beam)* H7 Park and turn lamp (front) 3457 AK Sidemarker (front) 168 Backup lamp 3156 K Stop, tail, turn and sidemarker lamp (rear) 3157 K Cornering lamp 3156 K License plate lamp 168 High-mount brakelamp - Stop** LED assembly Luggage compartment lamp 212-2 Map lamp 578 Visor vanity lamp - Slide on Rail system

(SOR)

A6224PF

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

Function Trade Number

Rear grab handle reading lamps 578 Door courtesy lamp 904 Glove compartment 194 All replacement bulbs are clear in color except where noted.

To replace all instrument panel lights - see your authorized dealer. * For vehicles with HID lamps, see your authorized dealer for service. ** When replacing the center high mount stop lamp assembly, see your

authorized dealer for service.

Replacing interior bulbs

Check the operation of all bulbs frequently.

Rear courtesy/reading lamps

To replace the rear courtesy/reading lamp bulbs in the rear assist handle:

1. Make sure the headlamp control is in the off position.

2. Under the handle, remove two trim screw covers, retaining screws, lamp assembly and assist handle from the headliner.

3. Disconnect the electrical connector from the lamp assembly.

4. Remove the two screws on the lamp assembly.

5. Pull the bulb straight out. To complete installation, follow the

removal procedure in reverse order.

Replacing exterior bulbs

Check the operation of all bulbs frequently. 48

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

Replacing headlamp bulbs

To remove the headlamp bulb:

1. Make sure the headlamp switch is in the off position, then open the hood.

2. Remove the three retainers on top of the radiator cover and the two retainers in front of the radiator cover.

3. Remove the three bolts for each headlamp.

4. Press the retainer next to the vertical aim adjuster, then pull the headlamp assembly forward and disconnect the electrical connector.

5. Remove the five screws and the protective bulb cover from the headlamp assembly.

Low beam

• Disconnect the electrical connector and remove the retainer and headlamp bulb from the headlamp assembly.

High beam

• Remove the bulb by turning it counterclockwise, then pull it straight out.

• Disconnect the electrical connector from the bulb.

WARNING: Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

6. To complete installation, follow the removal procedure in reverse order.

Note: To ensure a good seal, attach the bulb cover and partially tighten the screws. Check to ensure the gasket is fully centered. Finish tightening the screws in a criss-cross pattern (upper-left, lower right etc.)

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

Replacing HID low beam headlamp bulbs (if equipped)

The low beam headlamps on your vehicle use a “high intensity discharge” source. These lamps operate at a high voltage. When the bulb is burned out, the bulb and starter capsule assembly must be replaced by your authorized dealer.

Replacing front parking lamp/turn signal/sidemarker bulbs

The front parking lamp/turn signal/sidemarker bulbs are located in the headlamp assembly. Follow the same steps to replace these bulbs.

1. Make sure the headlamp switch is in the off position, then open the hood.

2. Remove the retainers and the radiator cover.

3. Remove the bolts, then pull the headlamp assembly forward and disconnect the electrical connector.

4. Rotate the bulb socket counterclockwise and remove from lamp assembly.

5. Carefully pull bulb straight out of the socket and push in the new bulb until it snaps, locking it into position.

6. To complete installation, follow the removal procedure in reverse order.

Replacing tail lamp/brake/turn lamp bulbs

The tail lamp, the brake lamp and the turn signal lamp bulbs are located in the tail lamp assembly. Follow the same steps to replace these bulbs.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

1. Make sure the headlamp switch is in the off position, then open the trunk and remove the retainer.

2. Carefully pull the carpet away to expose the lamp assembly hardware.

3. Remove the three nut and washer assemblies, then pull the lamp assembly away from the vehicle.

4. Remove the bulb socket by rotating it counterclockwise, then pull it out of the lamp assembly.

5. Pull the bulb from the socket and push in the new bulb.

6. To complete installation, follow the removal procedure in reverse order.

Lights

Replacing license plate lamp bulbs

1. Make sure the headlamp switch is in the off position, then remove two screws, grommets and the license plate lamp assembly from the trunk lid.

2. Carefully pull the bulb from the socket and push in the new bulb.

3. Install the lamp assembly on the trunk lid with two grommets, ensuring the grommets are pushed all the way in to the trunk lid and secure with two screws.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lights

Replacing backup lamp bulbs

1. Make sure the headlamp switch is in the off position, then open the trunk and carefully pull the trunk lid liner away to expose the lamp assembly.

2. Remove bulb socket from the trunk lid by turning it counterclockwise.

3. Pull the bulb straight out of the socket and push in the new bulb.

4. Install the bulb socket in trunk lid by turning clockwise.

Replacing high-mount brakelamp assembly

To change the high-mount brakelamp assembly:

1. Remove the high-mount brakelamp assembly from the headliner by pulling downward on the assembly.

2. Disconnect the electrical connector and remove the assembly.

3. Install the new assembly by aligning the tabs and pushing upward until it snaps in place.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

MULTI-FUNCTION LEVER

Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Press the end of the stalk:

• briefly: causes a single swipe of the wipers without washer fluid.

• a quick press and hold: the wipers will swipe three times with washer fluid.

• a long press and hold: the wipers and washer fluid will be activated for up to five seconds.

Courtesy wipe feature: One extra wipe will happen a few seconds after washing the front window to clear any water that is dripping down from the top of the windshield caused by the washing.

Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluid level frequently. Do not operate the wipers when the windshield is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield, always use the windshield washer. In freezing weather, be sure the wiper blades are not frozen to the windshield before operating the wipers.

Windshield wiper/washer features

When the windshield wipers are turned on during daylight, and the headlamp control is in the autolamp position, the exterior lamps will turn on after a brief delay and will remain on until the wipers are turned off.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

TILT STEERING WHEEL

To adjust the steering wheel:

1. Pull and hold the steering wheel release control toward you.

2. Move the steering wheel up or down until you find the desired location.

3. Release the steering wheel release control. This will lock the steering wheel in position.

WARNING: Never adjust the steering wheel when the vehicle is moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED)

Lift the mirror cover to turn on the visor mirror lamps.

Slide on rod feature (if equipped)

Rotate the visor towards the side window and extend it rearward for additional sunlight coverage.

Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

CLOCK

Press the right control to move the time display forward.

Press the left control to move the time display backward.

AUXILIARY POWER POINT (12VDC)

Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.

The auxiliary power point is located under the instrument panel. Do not use the power point for operating the cigarette lighter element (if

equipped). To prevent the fuse from being blown, do not use the power point(s)

over the vehicle capacity of 12 VDC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses.

To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged:

• do not use the power point longer than necessary when the engine is not running,

• do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.

Always keep the power point caps closed when not being used.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

REAR CENTER CONSOLE FEATURES (IF EQUIPPED)

The rear center console incorporates the following features:

• Utility compartment

• Auxiliary power point (if equipped)

• Remote radio/climate controls (if equipped)

• Remote seat adjustment (if equipped)

Remote seat adjustment

The rear passenger can move the front passenger seat forward or backward using the control located in the rear center console.

With the ignition is in the accessory position, move the control forward or backward to move front passenger seat.

Remote seat adjustment lockout

The window lockout control, located on the drivers door, will also lockout the remote seat adjustment. To lock out the remote seat adjustment feature, press the right side of the control. Press the left side to restore the remote seat adjustment control.

Rear console radio/climate controls (if equipped)

Refer to the Entertainment Systems and Climate Controls chapters for operation instructions.

Rear radio/climate controls lockout

The rear radio/climate control feature can be locked out by pressing the 3 and the 5 buttons on the radio simultaneously while the radio is on. To enable the rear radio/climate controls, press the 3 and the 5 buttons again.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

POWER WINDOWS

WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may

seriously injure themselves.

WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or

pets are not in the proximity of the window openings.

Press and pull the window switches to open and close windows.

• Press down (to the first detent) and hold the switch to open.

• Pull up (to the first detent) and hold the switch to close.

One-touch down

Allows the driver’s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.

Window lock

The window lock feature allows only the driver to operate the power windows.

To lock out all the window controls (except for the driver’s) press the right side of the control. Press the left side to restore the window controls.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Accessory delay

With accessory delay, the power window switches and radio may be used for up to 10 minutes after the ignition switch is turned off or until any door is opened.

INTERIOR MIRROR

The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side.

WARNING: Do not adjust the mirror while the vehicle is in motion.

Automatic dimming interior rear view mirror (if equipped)

Your vehicle may be equipped with an interior rear view mirror and a driver’s side exterior mirror that have an auto-dimming function. The electronic day/night mirrors will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the interior mirror. When the interior mirror detects bright light from behind the vehicle, the interior rear view mirror and the driver’s side exterior mirror (if equipped) will automatically adjust (darken) to minimize glare.

The mirrors will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up.

Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance.

Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

EXTERIOR MIRRORS

Power side view mirrors

WARNING: Do not adjust the mirror while the vehicle is in motion.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

To adjust your mirrors:

1. Rotate the control clockwise to

adjust the right mirror and rotate the control counterclockwise to adjust the left mirror.

2. Move the control in the direction

you wish to tilt the mirror.

3. Return to the center position to lock mirrors in place.

Memory feature (if equipped)

The power side view mirror positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected through the remote entry transmitter, keyless entry keypad or memory switch on the driver’s door. Refer to Memory seats/outside rear view mirrors/adjustable pedals in the Seating and Safety Restraints chapter.

Auto-dimming feature (if equipped)

For the auto-dimming feature on the driver’s side view mirror, refer to Automatic dimming interior rear view mirror in this chapter.

Heated outside mirrors

Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.

Note: If your vehicle is equipped with the auto dimming feature, the mirror glass is thicker and will take longer to defrost.

Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

(if equipped)

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Fold-away mirrors

Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)

The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.

Press and hold the rocker control to adjust accelerator and brake pedal.

• Press the bottom of the control to adjust the pedals toward you.

• Press the top of the control to adjust the pedals away from you.

WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL

With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.

WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Setting speed control

The controls for using your speed control are located on the steering wheel for your convenience.

1. Press the ON control and release it.

2. Accelerate to the desired speed.

3. Press the SET + control and release it.

4. Take your foot off the accelerator pedal.

5. The the instrument cluster.

Note:

• Vehicle speed may vary momentarily when driving up and down a steep hill.

• If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.

light will be displayed in

Disengaging speed control

To disengage the speed control:

• Press the brake pedal

Disengaging the speed control will not erase previous set speed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Resuming a set speed

Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed.

Increasing speed while using speed control

There are two ways to set a higher speed:

• Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the tap-up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control

There are two ways to reduce a set speed:

• Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET control to operate the tap-down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

• Press the brake pedal until the desired vehicle speed is reached, press the SET + control.

Turning off speed control

There are two ways to turn off the speed control:

• Press the brake pedal. This will not erase your vehicle’s previously set speed.

• Press the speed control OFF control.

Note: When you turn the speed control or the ignition off, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Driver Controls

Audio control features

In radio mode:

• Press NEXT to select the next preset station within the current radio band.

In tape mode:

• Press NEXT to listen to the next selection on the tape.

In CD mode:

• Press NEXT to listen to the next track on the disc.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

In any mode:

• Press VOL + or - to adjust the volume.

Climate control features (if equipped)

• Press TEMP + or - to adjust temperature.

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED)

The appearance of your vehicle’s universal garage door opener will vary according to your option package. Before programing, make sure your transmitter matches the graphic in the procedure.

HomeLink威

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Car2U威 Home Automation System

HomeLink姞 Wireless Control System (if equipped)

The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

WARNING: When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and

objects are out of the way to prevent potential injury or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Programming

Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the

accessory position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.

1. Position the end of your

hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view.

2. Simultaneously press and hold

both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons.

Note: Some entry gates and garage door openers may require you to replace Step 2 with procedures noted in the Gate Operator and Canadian Programming in this section for Canadian residents.

3. Firmly press and hold for five seconds and release the

programmed HomeLink威 button up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink威 button and observe the indicator light.

• If the indicator light stays on constantly, programming is complete

and your device should activate when the HomeLink威 button is pressed and released.

• If the indicator light blinks rapidly for two seconds and then turns

to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most

commonly a garage door opener).

4. At the garage door opener receiver (motor-head unit) in the garage,

locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit).

5. Firmly press and release the “learn” or “smart” button. (The name and

color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6.

6. Return to the vehicle and firmly press, hold for two seconds and

release the programmed HomeLink威 button. Repeat the 66

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.

HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 1 in this section. For questions or comments, please contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming

During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter.

After completing Step 1 outlined in the Programming section, replace Step 2 with the following:

Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.

• Continue to press and hold the HomeLink威 button (note Step 2 in the

Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency

signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 3 in the Programming section.

Operating the HomeLink姞 Wireless Control System

To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or

1–800–355–3515.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Erasing HomeLink姞 buttons

To erase the three programmed buttons (individual buttons cannot be erased):

• Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the Programming section.

Reprogramming a single HomeLink姞 button

To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps:

1. Press and hold the desired HomeLink威 button. Do NOT release the

button.

2. The indicator light will begin to flash after 20 seconds. Without

releasing the HomeLink威 button, follow Step 1 in the Programming section.

For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Car2U姞 Home Automation System (if equipped)

The Car2U威 Home Automation System is a universal transmitter located in the driver’s visor that includes two primary features – a garage door opener and a platform for remote activation of devices within the home. The Car2U威 system’s garage door opener function replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the interior of your vehicle. After being programmed for garage doors, the Car2U威 system transmitter can be programmed to operate security devices and home lighting systems.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

WARNING: Make sure that people and objects are clear of the garage door or security device you are programming. Do not

program the Car2U威 system with the vehicle in the garage.

Do not use the Car2U威 system with any garage door opener that lacks safety stop and reverse features as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).

Be sure to keep the original remote control transmitter for use in other vehicles as well as for future Car2U威 system programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed Car2U威 system buttons should be erased for security reasons. Refer to Erasing the Car2U威 Home Automation System buttons later in this section.

Read the instructions completely before attempting to program the Car2U威 system. Because of the steps involved, it may be helpful to have another person assist you in programming the transmitter.

Additional Car2U威 system information can be found on-line at www.learcar2U.com or by calling the toll-free Car2U威 system help line at 1-866-572-2728.

Types of garage door openers (rolling code and fixed code)

The Car2U威 Home Automation System may be programmed to operate rolling code and fixed code garage door openers.

• Rolling code garage door openers were produced after 1996 and are code protected. Rolling code means the coded signal is changed every time your remote control garage door opener is used.

• Fixed code garage door openers were produced prior to 1996. Fixed code uses the same coded signal every time. It is manually programmed by setting DIP switches for a unique personal code.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

If you do not know if your garage door opener is a rolling code or fixed code device, open your garage door opener’s remote control battery

O N

206-12

124

cover. If a panel of DIP switches is present your garage door opener is a fixed code device. If not, your garage door opener is a rolling code device.

Rolling code programming

Note: Programming the rolling code garage door opener involves time-sensitive actions. Read the entire procedure prior to beginning so you will know which actions are time-sensitive. If you do not follow the time-sensitive actions, the device will time out and you will have to repeat the procedure.

Note: Do not program the Car2U威 system with the vehicle in the garage.

Make sure that your key is on and engine off while programming the transmitter.

1. Firmly press the two outer Car2U威 system buttons for 1–2 seconds, then release.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

2. Go to the garage to locate the

garage door opener motor and its “learn” button. You may need a ladder to reach the unit and you may need to remove the unit’s cover or light lens to locate the “learn” button. Press the “learn” button, after which you will have 10–30 seconds to return to your vehicle and complete the following steps. If you cannot locate the “learn” button, refer to the Owner’s Guide of your garage door opener or call the toll-free Car2U威 system help line at 1-866-57Car2U (1-866-572-2728).

3. Return to your vehicle. Press and

hold the Car2U威 system button you would like to use to control the garage door. You may need to hold the button from 5–20 seconds, during which time the selected button indicator light will blink slowly. Immediately (within 1 second) release the button once the garage door moves. When the button is released, the indicator light will begin to blink rapidly until programming is complete.

4. Press and release the button again. The garage door should move,

confirming that programming is successful. If your garage door does not operate, repeat the previous steps in this section.

After successful programming, you will be able to operate your Car2U威 system by pressing the button you programmed to activate the opener. The indicator light above the selected button will turn on to confirm that the Car2U威 system is responding to the button command.

To program another rolling code device such as an additional garage door opener, a security device or home lighting, repeat Steps 1 through 4 substituting a different function button in Step 3 than what you used for the garage door opener. For example, you could assign the left-most button to the garage door, the center button to a security device, and the right-most button to another garage door opener.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

Note: The Car2U威 system allows for three devices to be programmed. If you need to change or replace any of the three devices after it has been initially programmed, it is necessary to erase the current settings using the Erasing the Car2U威 Home Automation System buttons procedure and then programming all of the devices being used.

Fixed code programming

Note: Do not program the Car2U威 system with the vehicle in the garage.

Make sure that your key is on and engine off while programming the transmitter.

1. To program units with fixed code DIP switches, you will need the garage door hand-held transmitter, paper and a pen or pencil.

2. Open the battery cover and record the switch settings from left to right for all 8 to 12 switches. Use the figure below:

When a switch is in the up, on, or + position, circle “L.”

When a switch is in the middle, neutral, or 0 position, circle “M.”

When a switch is in the down, off, or – position, circle “R.”

Switch position 123456789101112 Up,onor+ LLLLLLLLLLLL Middle, neutral or 0 MMMMMMMMMMMM Down, off or – RRRRRRRRRRRR L=left; M=middle; R=right

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

3. To input these positions into the

Car2U威 system, simultaneously press all three Car2U威 system buttons for a few seconds and then release to put the device into programming mode. The indicator lights will blink slowly. Within

2.5 minutes enter your

corresponding DIP switch settings from left to right into your Car2U威 system by pressing and releasing the buttons corresponding to the settings you circled.

4. After inputting switch settings, simultaneously press and release all

three Car2U威 system buttons. The indicator lights will turn on.

5. Press and hold the Car2U威

system button you would like to use to control the garage door. Immediately (within 1 second) release the button once the garage door moves. During this time the selected button indicator light will blink slowly. Do not release the button until you see the garage door move. Most garage doors open quickly. You may need to hold the button from 5–55 seconds before observing movement of the garage door.

6. The indicator light will (begin to) blink rapidly until programming is

complete. If your garage door opener does not operate following these steps, repeat Steps 2 through 6. Otherwise, call the toll-free Car2U威 help line at 1-866-57Car2U (1-866-572-2728).

Erasing the Car2U姞 Home Automation System buttons

Note: The system allows for three devices to be programmed. If you need to change or replace any of the three devices after it has been initially programmed, it will be necessary to erase the current settings using the procedure below and then reprogramming all of the devices being used.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

To erase programming on the Car2U威 system (individual buttons cannot be erased), use the following procedure:

1. Firmly press the two outside Car2U威 system buttons simultaneously for approximately 20 seconds until the indicator lights begin to blink rapidly. The indicator lights are located directly above the buttons.

2. Once the indicator lights begin to blink, release your fingers from the buttons. The codes for all buttons are erased.

If you sell your vehicle equipped with the Car2U威 system, it is recommended that you erase the programming for security reasons.

FCC and RSS-210 Industry Canada Compliance

The Car2U威 system complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.

Changes and modifications to the Car2U威 system transmitter by other than an authorized service facility could void authorization to use the equipment.

POWER TRUNK (IF EQUIPPED)

Your vehicle may be equipped with a power trunk controlled by the interior trunk control, the key fob or the keypad on the door.

If anything obstructs the power trunk while it is closing, the trunk will automatically reverse to the open position, provided it meets sufficient resistance. Resistance must be as strong as the force of the closing trunk, or stronger. The force of the closing trunk increases as the trunk approaches the latched position. The trunk will close with the next press of the interior trunk control or key fob button.

WARNING: Make sure all persons are clear of the luggage compartment area before using the power trunk control.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

If the battery is disconnected, discharged, or a new battery is installed, the power trunk needs to be reset. To reset the power trunk:

• Reconnect the battery with the trunk closed

• Power activate the trunk with the power interior trunk release, the

key fob or the keypad on the door to the full open position, then power activate the same power source and fully close the trunk. The power trunk is now reset.

INTERIOR TRUNK CONTROL

The remote trunk release control is located on the driver’s door trim panel and can be operated at any time except when your perimeter alarm system is armed.

If your vehicle is equipped with a power trunk, press the button once to open the trunk, press it again to close.

You can render the switch inoperable by locking the button with your master key.

The remote trunk release control and power door locks will be disabled when the vehicle perimeter alarm system is armed. This control will not work until the vehicle perimeter alarm system is disarmed. Refer to Perimeter alarm system in the Locks and Security chapter.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Driver Controls

FUEL DOOR RELEASE

Your vehicle is equipped with a locking fuel door. To open the door, press the control located on the door.

Fuel filler door override release

If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk to open the fuel filler door.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

KEYS

Your vehicle is equipped with a master key and a valet (identified with the word VALET) key lock system.

• The master key will access the vehicle’s doors, trunk, glove box, ignition and remote trunk release.

• The valet key will access doors and ignition only.

Before using the valet key with an attendant, lock the interior trunk control to disable the interior trunk control located on the drivers door, then lock the glove compartment with your master key. Do not hand over the remote entry transmitter or the master key to the valet attendant. For more information, refer to Interior trunk control in the Driver Controls chapter.

POWER DOOR LOCKS

• Press the doors.

Power door trim switch inhibit

This feature disables the power door locks and trunk interior release switches if all doors are closed and the perimeter alarm becomes armed.

Once the power door trim switches are disabled, they can only become active when perimeter alarm is disarmed.

control to unlock all

control to lock all

Smart locks

With the key in the ignition, in any switch position, and either the driver’s or passenger’s door open, the doors cannot be locked using the power door lock switches.

Central locking/unlocking

• All doors are locked when the key is inserted into the driver door key cylinder and turned to the lock position.

• The driver’s door is unlocked when the key is inserted into the driver door key cylinder and turned to the unlock position.

• If the key is turned a second time to the unlock position within five seconds, all vehicle doors will unlock.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Autolock

This feature automatically locks all vehicle doors when the following conditions are met:

• all the doors are closed,

• the engine is running,

• you shift into gear, putting the vehicle in motion, and.

• the vehicle’s speed is greater than 3 mph (5 km/h).

Autorelock

The autolock feature repeats when:

• a door is opened and closed while the engine is running,

• you shift into any gear, putting the vehicle in motion, and

• the vehicle’s speed is greater than 3 mph (5 km/h).

Autounlock

The auto-unlock feature will unlock all doors when:

• the ignition has been in the on position, all doors are closed, and the vehicle has been in motion at a speed greater than 3 mph (5 km/h),

• the vehicle has then come to a stop and the ignition is turned to the accessory or off position, and

• the driver door is opened (within ten minutes after the ignition was transitioned to the accessory or off position).

Note: The vehicle doors will not auto-unlock if the vehicle has been electronically locked prior to the driver door being opened.

Deactivating/activating the autolock or autounlock feature

Autolocking and autounlocking are independent features; either feature may be enabled or disabled without affecting the other.

You must complete Steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait at least 30 seconds. Note: Before following the procedure, make sure that the ignition is in the off position and all vehicle doors, the hood, and the decklid are closed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

1. Turn the ignition to the on position.

2. Press the power door unlock control on the door panel three times.

3. Turn the ignition from the on to the off position.

4. Press the power door unlock control three times.

5. Turn the ignition back to the on position.

6. The door locks will lock/unlock to confirm programming mode is entered/active.

7. With the ignition still in the on position, for the autolock feature, press the unlock control once then press the lock control once. The horn will chirp once to confirm successful programming. For the autounlock feature, press the lock control once, then press the unlock control once. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated.

If any door, the hood, or the deck lid is open, the horn will chirp twice, and the procedure will need to be performed again.

8. After having waited the necessary time for the programming to confirm, turn the ignition to the off position.

Once disabled, the autolock autounlock feature can be enabled by repeating the procedure in Steps 1–8.

CHILDPROOF DOOR LOCKS

• When these locks are set, the rear doors cannot be opened from the inside.

• The rear doors can be opened from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors.

• Move lock control up to engage the childproof lock.

• Move control down to disengage childproof locks.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and location of the release handle.

To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.

The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.

WARNING: Keep vehicle

doors and luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

WARNING: Do not leave children, unreliable adults, or animals

unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

REMOTE ENTRY SYSTEM

This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Radio type approval numbers for remote entry receiver

If the type approval of your remote entry system is inspected in one of the countries listed in the following table, refer to the corresponding approval number:

Remote entry receiver certification numbers

Gabon 01070305/ARTEL/GABTEL

Jordan CAZ/ENG/CA/04/11/1

Zambia TRC/LPD/2004/28

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

The remote entry system allows you to lock or unlock all vehicle doors without a key. Note: The remote entry features operate with the ignition in any position except in the on position, when the transmission is in any gear other than P (Park) or N (Neutral).

If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem.

Unlocking the doors

1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate.

2. Press

Security lighting

Your vehicle’s headlamps and park lamps will illuminate if:

• it is dark outside (evening),

• the headlamp control is in the autolamp position, and

• the unlock control is pressed on the remote entry transmitter.

The headlamps and parklamps remain illuminated:

• for 25 seconds, or

• until you turn the ignition from the off position, or

• until the vehicle doors are locked using the remote entry transmitter

or the power door unlock control.

and release again within five seconds to unlock all the doors.

Locking the doors

Press and release to lock all the doors. Note: The interior lamps will turn off and the parklamps will flash, if all the closures (doors, trunk, hood) are closed. If any closure is not closed, the parklamps will not flash.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Press and release again within five seconds to confirm that all the doors are closed. Note: The doors will lock again, the horn will chirp once and the parklamps will flash, if all the closures are closed. If any closure is not closed, the horn will chirp twice and the parklamps will not flash.

Car finder

Press parklamps/tail lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

Opening the trunk

Press once to open the trunk.

If your vehicle is fitted with the optional power decklid, press twice to open the trunk and twice to close it.

injured by the trunk lid. NEVER leave the remote entry transmitter where it can be inadvertently activated, as someone could be seriously injured by a moving decklid.

• Ensure that the trunk is closed and latched before driving your vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’s rear view.

The remote entry system allows you to open the trunk while the ignition is in any position. However, if the ignition is in the on position and the gearshift is in D (Drive), the trunk will only open if the vehicle is moving 3 mph (5 km/h) or slower.

twice within three seconds. The horn will chirp and the

WARNING: Before operating the power decklid, be sure that no one, particularly a child, is in a position where he or she can be

Sounding a panic alarm

Press panic alarm only works with the ignition in the off position.

Press the alarm in the following ways:

• Turn the ignition to the on or start positions.

• Wait two minutes and 45 seconds for the alarm to time-out.

on the remote transmitter to activate the alarm. Note: The

a second time to deactivate the alarm. You may also deactivate

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Memory seat/mirrors/adjustable pedals feature (if equipped)

The remote keyless entry system can also control the memory seats/mirrors/adjustable pedals feature. With this feature, the first two programmed transmitters will recall a different memory position.

Press features to the corresponding memory position, just as if you had pressed the memory control in the vehicle.

Activating the memory seat/mirrors/adjustable pedals feature

To activate this feature:

1. Position the seat, mirrors and adjustable pedals to the position desired.

2. Press the SET control on the driver’s door panel.

3. Within five seconds, press one control on the remote transmitter and then press the 1 or 2 button on the driver’s door panel to which you would like to associate with the memory positions and Driver 1 or Driver 2 positions.

4. Repeat this procedure for another remote transmitter, if desired.

Deactivating the memory seat/mirrors/adjustable pedals feature

To deactivate this feature:

1. Press the SET control on the driver’s door panel.

2. Within five seconds, press one control on the remote transmitter which you would like to deactivate and then press the SET control on the driver’s door panel .

3. Repeat this procedure for another remote transmitter, if desired.

once to unlock the driver’s door and move the memory

SET

Replacing the battery

The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

To replace the battery:

1. Twist a thin coin between the two

halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

2. Do not wipe off any grease on the

battery terminals on the back surface of the circuit board.

3. Remove the old battery.

Note: Please refer to local regulations when disposing of transmitter batteries.

4. Insert the new battery. Refer to

the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters

If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming.

How to reprogram your remote entry transmitters

You must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: Do not depress the brake pedal at any time during this procedure. If the brake pedal is pressed at any time during this procedure, programming mode will be exited and the entire procedure must be repeated.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Note: Ensure the brake pedal is not pressed during this sequence.

To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked.

2. Put the key in the ignition.

3. Cycle eight times rapidly (within 10 seconds) between the 1 (off) position and the 3 (on) position. Note: The eighth turn must end in the 3 (on) position.

4. The doors will lock, then unlock, to confirm that the programming mode has been activated.

5. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again.

6. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed.

7. Repeat Step 5 to program each additional remote entry transmitter.

8. Turn the ignition to the 1 (off) position after you have finished programming all of the remote entry transmitters. Note: After 20 seconds, you will automatically exit the programming mode.

9. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Illuminated entry

The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm.

The illuminated entry system will turn off the interior lights if:

• the ignition switch is turned to the on or the accessory position, or

• the remote transmitter lock control is pressed, or

• after 25 seconds of illumination.

The dimmer panel control must not be set to the off position for the illuminated entry system to operate.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

The battery saver will shut off the interior lamps 30 minutes after the last door is closed, or after 10 minutes if the last door is left open.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry keypad to:

• lock or unlock the doors without using a key.

• open the trunk.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box and is available from your authorized dealer. You can also create your own 5–digit personal entry code.

When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. Enter a sixth digit to indicate which personality feature should be

recalled by the personal code.

• 1 • 2 recalls driver personality 1.

• 3 • 4 recalls driver personality 2.

• 5 • 6, 7 • 8 and 9 • 0 do not recall a driver personality.

All of the vehicle doors will lock and unlock to confirm programming of the new code. Each driver personality profile (personality 1 or personality 2) can be associated with only one personal code. The factory-set code cannot be associated with a personality code.

You can program up to three personal codes to unlock your vehicle. These codes do not replace the permanent code that was provided by your authorized dealer.

1 2

4567890

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Tips for setting codes:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

Erasing personal codes

1. Enter the factory set 5–digit code. The keyless entry keypad and interior lights will illuminate and the driver’s door will unlock.

2. Press and release the 1 • 2 within five seconds of completing Step 1.

3. Press and hold the 1 • 2 for two seconds to erase the customer programmed codes. All of the vehicle doors will lock and then unlock to confirm erasure.

All personal codes are now erased and only the factory set 5–digit code will work.

Note: To exit programming mode, either wait 5 seconds after pressing 1

• 2 on the keypad, or press the 7 • 8 and 9 • 0 pads simultaneously to lock all vehicle doors and end programming mode.

Unlocking and locking the doors using keyless entry keypad

To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. Note: The driver’s door will unlock and the interior lamps will illuminate after the factory set 5-digit code or your personal code are correctly entered.

To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You

do not need to enter the keypad code first. Note: The interior lamps

will turn off. If the driver’s door is ajar, the doors will not lock.

Releasing the trunk with the keyless entry system

To release/open the trunk, enter the factory-set code or personal code (driver door unlocks) and press 5 • 6 within five seconds.

If your vehicle is equipped with the optional power decklid, pressing 5 • 6 again will close it (you may need to reenter the keypad code again).

WARNING: Before operating the power decklid, be sure that no

one, particularly a child, is in a position where he or she can be injured by the trunk lid. NEVER leave the remote entry transmitter where it can be inadvertently activated, as someone could be seriously injured by a moving decklid.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Anti-scan feature

If the wrong code has been entered seven times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

• the ignition is turned to the on position.

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM

SecuriLock威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition.

This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Radio type approval numbers for Immobilizer System PATS XCVR

If the type approval of your immobilizer system is inspected in one of the countries listed in the following table, refer to the corresponding approval number:

control on the remote entry transmitter.

Immobilizer System PATS XCVR certification numbers

TX Frequency: 134,2 kHz -8,1 dBµA/m @ 10 m

Country Name Type Approval Number

American Samoa (USA) See USA

Bahrain DLM/GEN/18/18/16

Barbados 340/3 Vol.II

Canada CANADA: 3043104475A

China CMII ID:2005DJ0428

Ghana SPLS / -485 / 2001

Guam (USA) See USA

Jordan 4/U/U/4250

Kenya CCK/ES/100/0

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Immobilizer System PATS XCVR certification numbers

Kuwait M.C/U.S.0 /5/7-12579

Mauritius TA/2005/15

Mayotte (F)

Mexico RLVVIVP03-324

Morocco MR 1299 ANRT 2004

Netherlands Antilles (NL)

Nicaragua NCG-CE-04-004

Northern Mariana Islands See USA

Oman OMA/1265(A) 1308/2001

Puerto Rico See USA

Qatar QTEL/SR/2003/R-276 Saudi Arabia (10/1900) South Korea R-LPD1-04-0145

Tunisia 269/MAT/2004

United Arabian Emirates 5/10-2/3274/3774

Uruguay 025/FR/2003

USA NT8-15607PAT3XCVR

Zambia CAZ/ENG/CA/2005/02/8

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Your vehicle comes with three coded keys; additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key.

Note: The SecuriLock威 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.

Anti-theft indicator

The anti-theft indicator is located on top of the instrument panel.

• When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock威 system is functioning as a theft deterrent.

• When the ignition is in the on position, the indicator will glow for three seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock威 system, the indicator will flash rapidly or glow steadily when the ignition is in the on position. If this occurs, turn the ignition off then back to on to make sure there was no electronic interference with the programmed key. If the vehicle doesn’t start, try to start it with the 2nd programmed key and if successful contact your authorized dealership for key replacement. If the indicator still flashes rapidly or glows steadily, the vehicle will not start, contact your authorized dealer as soon as possible for service.

Automatic arming

The vehicle is armed immediately after switching the ignition to the off position.

The theft indicator will flash every two seconds when the vehicle is armed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Automatic disarming

Switching the ignition to the on position with a coded key (programmed to your vehicle) disarms the vehicle and allows the

engine to start. The indicator on the instrument panel will illuminate for three seconds and then go out. If the indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your authorized dealer or a qualified technician.

Replacement keys

If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.

Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys

You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin.

Tips:

• A maximum of eight keys can be coded to your vehicle.

• Only use SecuriLock威 keys.

• You must have two previously programmed coded keys (keys that

already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If no previously programmed coded keys are available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

1. Insert a previously programmed coded key into the ignition.

2. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least one second, but no more than 10 seconds.

3. Turn the ignition to the 1 (off) position, and remove the coded key from the ignition.

4. After three seconds but within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition.

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least one second but not more than 10 seconds.

6. Turn the ignition to the 1 (off) position, and remove the second key from the ignition.

7. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition.

8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least one second.

9. Your new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s

engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your authorized dealer to have the new key(s) programmed.

To program additional new unprogrammed key(s), repeat this procedure from Step 1 for each additional key.

PERIMETER ALARM SYSTEM (IF EQUIPPED)

The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle.

If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Locks and Security

Arming the system

When armed, the perimeter alarm will notify you of an unauthorized entry. When unauthorized entry occurs, the system will flash the park lamps and will sound the horn.

The system is ready to arm whenever the key is out of the ignition. Any of the following actions will arm the alarm system:

• Press the remote transmitter lock control one time to arm the system.

• Lock all doors using the keypad.

• Lock all doors using the interior power lock switch while the driver or

passenger door is open and then closed.

• Lock all doors with the key in the key lock cylinder.

If all the closures (doors, trunk, hood) are closed, the park lamps will flash once and the horn will chirp once when the entry transmitter is pressed a second time within five seconds.

If any closure is not properly closed, the park lamps will not flash and the horn will chirp twice.

The system will wait 20 seconds after one of the above actions is performed before allowing the alarm to be armed. After the 20–second pre-arm phase, the interior trim remote trunk release control and the interior trim power door unlock control are disabled, in order to further protect your vehicle.

Disarming the system

You can disarm the system by any of the following actions:

• Unlock the doors by using the remote entry transmitter.

• Unlock the doors using a valid code on the keypad.

• Unlock the doors with the key in the key lock cylinder.

• Turn the ignition to the on position.

on the remote

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

SEATING

Adjustable head restraints

WARNING: To minimize the risk of neck injury in the event of a

crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.

Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.

The head restraints can be moved up and down.

Push control to lower head restraint.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

Using the manual recline function (if equipped)

WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.

WARNING: Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal

injuries in the event of a collision.

To adjust the front seatback using the manual recliner:

• Lift and hold the handle located on the side of the seat.

• Lean against the seatback to adjust it to your desired position. You can recline the seat back or bring it forward.

• Release the handle when the desired position has been reached.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

Front seat armrest

The front seat armrest has a locking pin which prevents the armrest from folding down during a collision. If the locking pin has engaged because of a substantial jolt, but no collision has occurred, you can disengage the locking pin by first moving the armrest forward until it stops to align the hole with the locking pin, then by pushing a small tool through the access hole provided.

WARNING: Ford Motor Company recommends that all front

seat armrests should be inspected by an authorized dealer after any collision to verify that the locking pin feature has not been damaged. The front seat armrest must be replaced if either damage or improper operation is found. Failure to replace a damaged front seat armrest may result in the armrest falling suddenly during a collision, which could lead to serious injury.

To gain access to the storage compartment in your armrest, press the button, on either the driver or passenger side, to unlatch and open the lid.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

Using the power lumbar support (if equipped)

The power lumbar control is located on the front inboard side of the seat.

Press the top side of the control to adjust firmness.

Press the bottom side of the control to adjust softness.

Adjusting the power front seats

The controls for the power seats are located on the inside of each front door.

WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.

WARNING: Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal

injuries in the event of a collision.

WARNING: Sitting improperly out of position or with the seat

back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

WARNING: To reduce the risk of possible serious injury: Do not

hang objects off seat back or stow objects in map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check Passenger Airbag Disable Indicator for proper airbag status. Refer to Front passenger sensing system in the Airbag supplemental restraint system (SRS) chapter for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.

Press the control to recline the seatback forward or backward.

Press to move the seat forward or backward.

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Seating and Safety Restraints

Press to move the front portion of the seat cushion up or down.

Press to move the rear portion of the seat cushion up or down.

Heated seats (if equipped)

WARNING: Persons who are unable to feel pain to the skin

because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Note: Do not do the following:

• Place heavy objects on the seat

• Operate the seat heater if water or any other liquid is spilled on the

seat. Allow the seat to dry thoroughly.

The heated seat control is located on the driver’s or front passenger’s door.

100

2010 Town Car (tow) Owners Guide, 1st Printing USA (fus)

Lincoln Town Car 2010 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Introduction

CONGRATULATIONS

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

Warning symbols on your vehicle

Protecting the environment

PERCHLORATE MATERIAL

BREAKING-IN YOUR VEHICLE

SPECIAL NOTICES

New Vehicle Limited Warranty

Special instructions

DATA RECORDING

Service Data Recording

Event Data Recording

CELL PHONE USE

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION

Instrument Cluster

WARNING LIGHTS AND CHIMES

GAUGES

MESSAGE CENTER

Info (Information menu)

Compass zone/calibration adjustment

System warnings

Entertainment Systems

AUDIO SYSTEMS

Premium AM/FM Stereo Single CD/Cassette system

Premium plus AM/FM Stereo In-dash Six CD sound system

Rear console audio controls (if equipped)

GENERAL AUDIO INFORMATION

Climate Controls

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM

Operating tips

REAR CONSOLE CLIMATE CONTROLS (IF EQUIPPED)

REAR WINDOW DEFROSTER

Lights

HEADLAMP CONTROL

Autolamp control

High beams

Flash to pass

Daytime running lamps (DRL) (if equipped)

PANEL DIMMER CONTROL

AIMING THE HEADLAMPS

Vertical aim adjustment

TURN SIGNAL CONTROL

INTERIOR LAMPS

Map/courtesy lamps

Rear courtesy/reading lamps

BULB REPLACEMENT

Lamp assembly condensation

Using the right bulbs

Replacing interior bulbs

Rear courtesy/reading lamps

Replacing exterior bulbs

Replacing headlamp bulbs

Replacing HID low beam headlamp bulbs (if equipped)

Replacing front parking lamp/turn signal/sidemarker bulbs

Replacing tail lamp/brake/turn lamp bulbs

Replacing license plate lamp bulbs

Replacing backup lamp bulbs

Replacing high-mount brakelamp assembly

Driver Controls

MULTI-FUNCTION LEVER

Windshield wiper/washer features

TILT STEERING WHEEL

ILLUMINATED VISOR MIRROR (IF EQUIPPED)

CLOCK

AUXILIARY POWER POINT (12VDC)

REAR CENTER CONSOLE FEATURES (IF EQUIPPED)

Remote seat adjustment

Remote seat adjustment lockout

Rear console radio/climate controls (if equipped)

Rear radio/climate controls lockout

POWER WINDOWS

One-touch down

Window lock