LINAK A S HC40BL User Manual

HC40BL

User manual

LINAK.COM/HOMELINE

Page 1 of 40

Contents

Preface................................................................................................................................................ 3

Valid for .............................................................................................................................................. 4

Important information ..................................................................................................................... 5

Safety instructions .......................................................................................................................... 5

Safety issues .................................................................................................................................. 5

Only for EU markets ........................................................................................................................ 8

Only for Non EU markets ............................................................................................................... 8

Misuse ............................................................................................................................................... 8

Informations importantes ............................................................................................................... 9

Consignes de sécurité ...................................................................................................................... 9

Seulement pour les marchés au sein de l´UE .............................................................................. 10

Seulement pour les marchés hors UE .......................................................................................... 10

Utilisation abusive ......................................................................................................................... 10

Repairs ............................................................................................................................................. 11

Manufacturer’s declaration........................................................................................................... 11

Misc. on the HOMELINE

®

system ................................................................................................... 12

Warranty......................................................................................................................................12

Maintenance................................................................................................................................ 12

ETL-marking ..................................................................................................................................... 13

Getting started ............................................................................................................................... 14

Batteries and how to change for the HC40 FRAME

TM

Advanced..................................................... 14

Batteries and how to change for the HC40 TWISTTM Advanced ...................................................... 15

Navigation ....................................................................................................................................... 16

Screen elements .............................................................................................................................. 16

Setting time and day ...................................................................................................................... 17

Screen saver.................................................................................................................................... 18

Motion sensor................................................................................................................................. 19

Favourite positions ........................................................................................................................ 21

Massage .......................................................................................................................................... 23

My bed menu .................................................................................................................................. 25

About ............................................................................................................................................. 26

Me ............................................................................................................................................. 27

Alarms ............................................................................................................................................. 28

Sleep timer ...................................................................................................................................... 29

Shortcuts ......................................................................................................................................... 30

Time & Day ...................................................................................................................................... 31

Language ......................................................................................................................................... 32

Child lock ........................................................................................................................................ 33

Torch ............................................................................................................................................. 34

Notifications ................................................................................................................................... 35

Disposal of LINAK’s products ...................................................................................................... 36

Main groups of disposal ............................................................................................................... 36

Disposal of batteries ..................................................................................................................... 36

Labels ............................................................................................................................................. 37

Drawings ......................................................................................................................................... 38

Addresses ........................................................................................................................................ 40

Page 2 of 40

Preface

We are delighted that you have chosen a product from LINAK®.

LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.

This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It
is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.

We are sure that your LINAK product/system will give you many years of problem-free operation.

Before our products leave the factory they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local dealer.

LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.

LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance
with the specifications, maintenance being done correctly and any repairs being carried out at a service centre,
which is authorised to repair LINAK products.

Changes in installation and use of LINAK products/systems can affect their operation and durability. The
products are not to be opened by unauthorised personnel.

The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.

LINAK A/S

Page 3 of 40

Valid for:

This User Manual is valid for the following products:

Controls: HC40 FRAMETM Advanced and HC40 TWISTTM Advanced

Page 4 of 40

Important information

Important information on LINAK

®

products can be found under the following

headings:

Warning!

Failure to comply with these instructions may result in accidents involving
serious personal injury.

Failing to follow these instructions can result in the product being damaged
or being destroyed.

Safety instruction

General

Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.

Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.

It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – risk of injury if these instructions are not followed.

The appliance is not intended for use by young children or infirm persons
without supervision.

If there is visible damage on the product it must not be installed.

Assure free space for movement of application in both directions to avoid blockade.

The appliance is only to be used with the power supply unit provided with the
appliance.

Safety issues

The builder of the equipment shall ensure that the use of the component
complies with relevant standards – like the Machine Directive. Care must be
taken to avoid squeezing of cables as it can cause movement of the system!

Updated manuals and declarations can always be found here:
www.linak.com/homeline

Page 5 of 40

This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions:

(1) This device may not cause harmful
interference, and

(2) This device must accept any
interference received, including
interference that may cause
undesired operation

• Statement – for all intentional and unintentional radiators:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

• Statement for digital devices for Class B:
NOTE: This equipment has been tested and found to comply with the limits for
a Class B diwgital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions it may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Page 6 of 40

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:
(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause
undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :

(1) l’appareil nedoit pas produire de brouillage, et
(2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Labeling Requirements:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Page 7 of 40

Only for EU markets

This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.

Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.

Only for Non EU markets

Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/products,
unless they are under surveillance or they have been thoroughly instructed in
the use of the apparatus by a person who is responsible for the safety of these
persons.

Moreover, children must be under surveillance to ensure that they do not
play with the product.

Misuse

Do not overload the actuators – this can cause danger of personal injury and
damage to the system.

Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.

Do not use the system in environments other than the intended indoor use

Page 8 of 40

Informations importantes

®

Les informations importantes sur les produits LINAK

peuvent être trouvées dans

les rubriques suivantes:

Attention!

Le non respect de ces instructions peut entraîner des accidents impliquant
des blessures graves.

Ne pas suivre ces instructions peut entraîner l´endommagement ou
destruction du produit.

Consignes de sécurité

Géneral

L´utilisation en toute sécurité du système n´est possible que si l´intégralité des
instructions ont été lues et ont été strictement suivies.

Le non respect de se conformer aux instructions marquées du symbole “note” peut
entraîner de graves dommages au système ou à un de ses composants.

Il est important pour tout individu qui connecte, installe, ou utilise le système
d´avoir les informations nécessaires et l´accès à ce mannuel d´utilisation.

Suivez les instructions pour le montage – risque de blessure si ces instructions
ne sont pas suivies.

L´appareil n´est pas destiné à être utilisé par des enfants ou des personnes
handicapées sans surveillance.

S´il y a des dommages visibles sur le produit, l´installation ne doit pas être
effectuée.

Assurez un espace libre autours du materiel pour éviter tout blocage.

Le constructeur de l’équipement doit s’assurer que l’utilisation du composant
conforme aux normes en vigueur, comme la Directive Machines. Les soins
doivent être prises pour éviter de pincer les câbles car cela pourrait entraîner
des mouvements du système!

Les mises à jours des manuels et autres informations peuvent-être trouvées sur
www.linak.com/homeline

Page 9 of 40

Seulement pour les marchés au sein de l´UE:

Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi
que les personnes dont les capacités physiques, sensorielles ou mentales
sont réduites ou ayant un manque d´expérience et de connaissance si elles
ont bénéficié d´une surveillance ou d´instructions concernant l´utilisation de
l´appareil en toute sécurité et compris les risques encourus.

Les enfants ne doivent pas jouer avec l´appareil. Le nettoyage et l´entretien ne
doivent pas être rèalisés par des enfants sans surveillance.

Seulement pour les marchés hors UE:

Les personnes qui n´ont pas l´expérience ou les connaissances nécessaires sur
le ou les produit(s) ne doivent pas le ou les utiliser. Par ailleurs, les personnes
ayant des capacités physiques, sensorielles ou mentales réduites ne doivent
pas utiliser le ou les produit(s), sauf si elles sont sous surveillance ou ont
suivi une formation approfondie de l´utilisation de l´appareil par l´individu
responsable de la securité de ces personnes.

De plus, les enfants doivent-être sous surveillance afin de s´assurer qu´ils ne
jouent pas avec le produit.

Utilisation abusive:

Ne surchargez pas les actionneurs – cela peut engendrer un risque de
blessures corporelles et endommager le système.

Ne pas utiliser les actionneurs pour soulever des personnes. Ne pas s´asseoir
ou se tenir debout sur une table en fonctionnement – risque de blessures.

Ne pas utiliser le système dans dans des environnements autres que
l´utilisation intérieure prévue.

Page 10 of 40

Repairs

In order to avoid the risk of malfunction, all HOMELINE® repairs must only be carried out by authorised LINAK® workshops or
repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned
to authorised LINAK workshops.

Warning!

If any of the HOMELINE® products are opened, there will be a risk of subsequent malfunction.

Warning!

The HOMELINE® systems are not resistant to cutting oil.

Page 11 of 40

Misc. on the HOMELINE® system

Warranty

There is a 36 months’ warranty on the HC40 products against manufacturing faults calculated from the production date of
the individual products (see label). The LINAK warranty is only valid in so far as the equipment has been used and maintained
correctly and has not been tampered with. Furthermore, the system must not be exposed to violent treatment. In the event of
this, the warranty will be ineffective/invalid. For further details, please see standard terms of sale and delivery for LINAK A/S.

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.

The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

Page 12 of 40

ETL-marking

Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.

C/N 120690

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United
States

C/N 9901916

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United
States

C/N 4008003

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4008005

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4008671

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4009507

Conforms to UL962
Cert. to CSA Std. No. 68-09

ETL Recognized Component mark for Canada and United States

Page 13 of 40

Getting started

Batteries and how to change for the HC40 FRAMETM Advanced

The hand control needs 2 x AAA batteries.

1. Press the button located inside the oval arch at the bottom of the hand control. Take off the battery lid.

2. Put in the new batteries as indicated in the housing.

We recommend to use alkaline batteries. Using another type of batteries can lead to unintended restart of the hand
control.

3. Reattach the battery lid by placing the lower end of the lid and then press below the ‘down’ button.

After insertion of the batteries in the HC40, a start-up logo appears for 5 seconds.

Page 14 of 40

Batteries and how to change for the HC40 TWISTTM Advanced

The hand control needs 2 x AAA batteries.

1. Open the battery lid on the front of the HC40, by pressing and sliding it in the opposite direction of the keypad.

2. Put in the new batteries as indicated in the housing.

We recommend to use alkaline batteries. Using another type of batteries can lead to unintended restart of the hand
control.

3. Reattach the battery lid by placing it back on the hand control and then slide it on in the direction towards the keypad.

Page 15 of 40

Navigation

The HC40 has 10 buttons. The picture below explains the functionality of the buttons:

Screen elements

Menu colours:

White References
Blue Favourite positions
Green Massage control
Orange My bed menu

Page 16 of 40

Setting time and day

1. Press button 1 to switch between 24H and AM/PM.

2. Adjust the time by using the ‘up’ and ‘down’ buttons

on the keypad. Once the hours and minutes are
adjusted, “SAVE” appears in the display. Press the
‘select’ button or button 3 “SAVE” to save the time.

3. Use the ‘left’ and ‘right’ buttons to adjust the day of

the week. Press the ‘select’ button or button 3 “SAVE”
to save the day.

The hand control is now ready for exploring the menu and the features.

Page 17 of 40

Screen saver

After 10 seconds of inactivity the HC40 dims the light in the display. After another 10 seconds in dimmed light, the display turns
off.

The next time the hand control is picked up, the screensaver (time and day) or a notification shows.

Page 18 of 40

Motion sensor

After setting the time and day in the HC40, the motion sensor is enabled. The screen now reacts on any movement of the hand
control. E.g. the screen turns on, when the user picks up the hand control.

As the motion sensor may cause the batteries to empty during bumpy transportation before the hand control reaches its
destination, we recommend the bed producer not to complete the time and day registration in the HC40 if the hand control is
delivered to the end user with batteries in.

Demo mode and how to pair

As long as the remote is not paired to any actuator system, the menu structure will be accessible to loop around in for
demonstration purposes. We call this demo mode.

After 5 minutes active surfing around the menu structure in demo mode, a ‘help-to-pair’ guide appears.

1. Set the bed in pairing mode by applying power to the system.

2. Press button 1 and 3 at the same time.

3. With successful pairing a blue circle with a check mark shows. The HC40 and actuator system are now paired up.

Figure 1: Pairing command Pairing successful

The Demo mode is ended as soon as the actuator system and the HC40 are paired and connected. Up and down arrows are
now visible on the screen surrounding the reference name, showing that the system can now run.

Page 19 of 40

Figure 2: HC40 not paired HC40 paired

For customers pairing the HC40 to the actuator system on the production line when producing the bed, it is possible to pair
the system already after the start-up logo is gone. No need to enter time and day before making the pairing procedure.

How to run references

The menu structure can contain up to four references: back, leg, neck and foot. Loop between the references using the ‘left’
and ‘right’ buttons. To run the references simply go to the screen with the reference and press the ‘up’ or ‘down’ arrow and the
system runs in the requested direction.

Figure 3: Looping between references and up/down drive of them

Page 20 of 40

Favourite positions

Save favourite positions

The HC40 allows for storing up to four favourite positions.

1. Drive the bed to the desired position.

2. Loop to the “SAVE FAVOURITE” screen using the ‘left’ and ‘right’ buttons.

3. When the screen is reached, press button 3 “SAVE”.

4. Highlight one of the four favourite positions using the ‘up’ and ‘down’ buttons and press the ‘select’ button to save the

position as the selected “FAVOURITE”.

5. The saved “FAVOURITE” will now show in the main menu loop.

Figure 4: Step 3 Step 4 Step 5

As soon as all positions are saved, the “SAVE” option becomes hidden. It will be shown again as soon as one of the four saved
positions is deleted.

Page 21 of 40

From the screen with the favourite position, there are three options:

A. Drive to the favourite position

1. Press and hold button 3 ”GO TO” or the ‘select’ button.

2. The system now drives towards the position while

the name flashes in the display

B. Rename the favourite position (Not possible in Korean language)

1. Press button 2 “RENAME”.

2. Use the ‘left’ and ‘right’

buttons to loop between
the characters.

3. Press the ‘select’ button

to choose a character and
it shows in the blue bar.

4. Use button 1 “DELETE”

to delete a character or
button 2 “SPACE” to
make a space between
the characters.

5. When the desired name is

typed in, press button 3
“SAVE” to save the
new name.

C. Deleting a favourite position

1. Press button 1 “DELETE”.

2. Confirm the deletion by pressing button 3 “YES”.

3. The position is now deleted and removed from

the general menu loop.

Page 22 of 40

Massage

Controlling massage

The HC40 FRAME™ Advanced can control up to two massage references. The two standard options are
called “MASSAGE BACK” and “MASSAGE LEG”.

Loop in the menu to find the massage screens. From the massage screen it is possible to:

• Set a timer

• Change massage mode

• Turn on/off the massage

• Adjust intensity

Setting a timer

1. Press button 1 “TIMER” to set a timer for the duration of the massage session.

2. Use ‘up’ and ‘down’ buttons to adjust the minutes.

3. Press button 3 “SAVE” to save the duration and start the massage.

Note: If the timer in the HC40 is set to a higher number than what is configured in the actuator system as timer, the massage
will stop according to the configuration in the actuator system.

Page 23 of 40

Changing massage mode

1. Press button 2 “MODE” to change massage mode.

2. A green circle appears, and the massage mode is

now changed.

3. Repeat to toggle between more available modes.

Note: The number of massage modes depends on the
configuration in the actuator system.

Turnning on/off the massage

1. Use button 3 to turn on/off the massage motor.

This action must be repeated for both screens
“MASSAGE BACK” and “MASSAGE LEG” if both
massage options are to be turned on/off.

Adjusting intensity

1. Use the ‘up’ button to increase the massage

intensity.

2. Use the ‘down’ button to decrease the

massage intensity.

Page 24 of 40

My bed menu

The “MY BED” menu is accessed by looping the menu with the ‘left’ or ‘right’ button, or via button 3 “MENU” on the
main screen.
Once “MY BED” appears, press the ‘select’ button to access the “MY BED” menu.

The items in the “MY BED” menu depend on the number of features configured. The maximum list consists of the
following items:

• ME

• ALARMS

• SLEEP TIMER (optional)

• SHORTCUTS

• TIME&DAY

• LANGUAGE

• CHILD LOCK

• TORCH

• ABOUT

Page 25 of 40

About

The “ABOUT” section contains information about the product: the item
number, the software number and version, and whether the control has
been reconfigured. The item and software numbers also appear on the
product label underneath the battery lid.

The about section contains the CE symbol and WEEE garbage can for
approval reasons.

From the about section, it is possible to reset the hand control to default factory settings:

1. Press button 2 “RESET”.

2. A warning pops up - confirm the request by pressing button 3 “YES”.

3. The hand control is now reset meaning that every setting changed after receiving the hand control has been restored to the

default factory settings. The settings affected by the reset are: favourite positions, my name, shortcuts, time and time
format, day, alarms, child lock, language and any timers.

Figure 5: Step 1: Reset Step 2: Confirm Step 3: Back to factory settings

Page 26 of 40

Me

In the “ME” section it is possible to enter a name. By entering a name, the notifications get personalised, meaning
“HAVE A NICE DAY” is now followed by the entered name.

1. Highlight the “ME” bar in the “MY BED” menu and press the ‘select’ button.

2. Press button 3 “EDIT” to enter a name.

2.1. Use the ‘left’ and ‘right’ buttons to loop between the characters.

2.2. Press the ‘select’ button to select a character.

2.3. Press button 1 “DELETE” to delete a character or button 2 “SPACE” to make a space between the characters.

3. When the desired name is typed in, press button 3 “SAVE” to save the name.

Page 27 of 40

Alarms

The alarm menu is accessible for systems including massage. When the alarm goes off, the massage motors start, providing a
soundless wake-up.

Highlight the “ALARMS” bar in the “MY BED” menu and press the ‘select’ button to access the alarm menu, which contains
three alarms.

1. Press the ‘select’ button to enable the alarm. The icon changes to green.

2. Press button 2 “EDIT” to change the alarm.

3. To disable an alarm, simply highlight the alarm and press the ‘select’ button. The icon changes to white/grey.

When the alarm goes off, the massage motors start in the latest used mode and
the HC40 screen shows a bell.

a. Press button 1 “SNOOZE” to snooze the alarm for 9 minutes.
b. Press button 3 “STOP” to stop the alarm.

When the alarm is stopped, it is disabled, and the user has to go to the alarm
menu to enable the alarm again for the next wake-up.

Page 28 of 40

Sleep timer

The sleep timer functionality is a timer for the bed to return to flat position or a predefined favourite position, e.g. a sleeping
position with the head a little raised. A typical use scenario could be a user wanting to fall asleep watching TV. He has the back
of the bed raised and he sets the timer to 30 minutes on the HC40. When the timer elapses, the bed drives to flat position and
he can sleep in a comfortable position.

The sleep timer functionality requires impulse drive enabled.

Highlight the “SLEEP TIMER” bar in the “MY BED” menu and press the ‘select’ button to access the sleep timer.

1. Use the ‘up’ and ‘down’ buttons to adjust the time.

2. Press button 3 “START” to start the timer.

A ‘moon’ icon is now shown next to the time to indicate that the sleep timer is on.

Cancelling/stopping the sleep timer

1. Access the “SLEEP TIMER”.

2. Press button 3 “CANCEL” to stop the timer.

Page 29 of 40

Shortcuts

It is possible to set shortcuts on the HC40. The shortcuts are meant for the user to put
in his/her most used features, so they are only one click away from the main screen.
This way the hand control can be personalised to the needs of the individual user.

The shortcut buttons are the top row of buttons referring to the text in the display.

Setting the shortcuts

Highlight the “SHORTCUTS” bar in the “MY BED” menu and press the ‘select’ button
to access.

1. Highlight the bar with the wanted shortcut and press the ‘select’ button or button

2 “EDIT”.

2. Highlight one of the options:

- NONE (to remove a programmed shortcut)

- ALARMS

- FAVOURITE (saved favourite positions)

- SLEEP TIMER (configurable)

- TORCH

- MY BED

- CHILD LOCK

- ABOUT

3. Press the ‘select’ button to choose the highlighted option.

A notification confirms the shortcut is saved.

The shortcut is now visible on the main screen and accessible in one click.

Page 30 of 40

Time & Day

It is possible to adjust the time set during set-up of the hand control in the “TIME&DAY” menu in the “MY BED” menu.

1. Highlight the “TIME&DAY” bar in the “MY BED” menu and press the ‘select’ button to access.

2. Set the time:

2.1. Highlight the “TIME” bar and press the ‘select’ button or button 2 “EDIT”.

2.2. Use the ‘up’ and ‘down’ buttons to adjust the time. Press button 1 to switch between 24H and AM/PM.

2.3. Press the ‘select’ button or button 3 “SAVE” to save the time.

3. Set the day:

3.1. Highlight the “DAY” bar and press the ‘select’ button or button 2 “EDIT”.

3.2. Use the ‘left’ and ‘right’ buttons to scroll to the actual day of the week.

3.3. Press the ‘select’ button or button 3 “SAVE” to save the day.

Page 31 of 40

Language

The HC40 comes in seven different languages: English (British), French, Spanish, German, Swedish, Danish and Korean.

1. Highlight the “LANGUAGE” bar in the “MY BED” menu and press the ‘select’ button to access the menu.

2. Use the ‘up’ and ‘down’ buttons to scroll through the languages.

3. Highlight the desired language and press the ‘select’ button.

A notification tells the user that the language is being set.

Page 32 of 40

Child lock

It is possible to set a child lock on the HC40, meaning a specific button combination must be pressed to unlock the hand
control before it is possible to run the bed.

Enabling the child lock

1. Highlight the “CHILD LOCK” bar in the “MY BED” menu

2. Press the ‘select’ button and a notification shows.

3. Press the ‘select’ button or button 3 “OK” to activate child lock.

4. The icon changes to green to indicate that child lock is enabled.

Unlocking the hand control

Child lock enabled is illustrated by a ‘lock’ icon at the top of the screen saver.

1. To unlock, press and hold at the same time the ‘left’ and ‘right’ buttons for 3 seconds until the main screen shows.

A guide explaining this procedure pops up at any press on a button from the locked screen saver.

Page 33 of 40

Torch

On the backside of the hand control is a torch.

Turning the torch on/off

1. Highlight the “TORCH” bar in the “MY BED” menu.

2. Press the ‘select’ button to enable the torch.

3. The first five times a tip on how to turn on/off the torch by shaking the hand control shows. Press the ‘select’ button or

button 3 “OK”. The icon changes to green and torch is now on.

The torch can also be turned on directly from any screen. Simply shake the hand control sideways twice. To turn it off, simply
shake the hand control twice again.

Page 34 of 40

Notifications

The HC40 sends notifications to the user to give a personal experience. When a name is typed in, the notification will adapt to
that.

The standard notification “HAVE A NICE DAY [name]” appears when the hand control is picked up in the time slot from 05.00
to 11.00 every third Saturday.

The standard notification “GOOD MORNING [name]” appears when the hand control is picked up in the time slot from 05.00
to 09.00 every second Wednesday.

The HC40 also shows other notifications to the user e.g. about how to pair if the HC40 is not connected to the bed, or if the
battery has reached a low level.

Figure 6: Examples of notifications

Page 35 of 40

Disposal of LINAK’s products

As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that
enables a classification to different waste fractions for recycling or combustion.

Guidance

We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or
combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material and recoverable resources.
Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/aluminium/copper and
plastic can be divided into ABS/PA/PE/PP.
As an example, the table below breaks down the different components in LINAK products to various recycling groups:

Product Components Recycling group

Column/ Actuator : Spindle and motor

Control Box : PC boards

Handset/Control : Plastic housing

Plastic housing
Cable
PC boards

Plastic housing
Cable
Transformer

Cable
PC boards

By now, almost all our casted plastic parts are supplied with an interior code for plastic types and fibre contents, if any.

Main groups of disposal

Product main groups Metal

scrap

HC40 FRAMETM Advanced

HC40 TWISTTM Advanced

X X X

X X X

Cable
scrap

Electronics

scrap

Metal scrap
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap

Electronics scrap
Plastic recycling or combustion
Cable scrap or combustion
Metal scrap

Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap

Plastic recycling or

combustion

Comments

Disposal of batteries

"Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that
used or leaking batteries are disposed through local recycling system. Please do not throw used or leaking batteries in normal
household waste or in nature. This will cause damage to the enviroment.

How to deal with leaking batteries

Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product, the batteries must be removed at once to minimise damage to the product. If
leaking batteries are left in the product, it become defective.

It is recommended to use plastic gloves when handling leaking batteries. The contents of a leaking batteries can cause chemi­cal burns and respiratory irritation.

If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please seek medical
attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek medical attention."

Page 36 of 40

Labels

Label for HC40 FRAMETM Advanced

Label for HC40 TWISTTM Advanced

LINAK APPLICATION POLICY

The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as
hardware, software, technical advice, etc. related to an existing or new customer application.

LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk and
Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be installed, used, and operated, as
each individual application is unique.

The suitability and functionality of the LINAK product and its performance under varying conditions (application, vibration,
load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be the responsibility of the
LINAK customer using any LINAK product.

LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the
responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.

Page 37 of 40

DRAWING APPENDIX

HC40 FRAMETM Advanced

Page 38 of 40

HC40 TWISTTM Advanced

Page 39 of 40

FACTORIES

China

LINAK (Shenzhen) Actuator Systems, Ltd.
Phone: [phone]
Phone: [phone]
E-mail: [e-mail]
www.linak.cn

Denmark - Headquarters

LINAK A/S - Group Headquarters

Phone: [phone]
Fax: [phone]
Fax (Sales): [phone]
E-mail: [e-mail]
www.linak.com

USA

LINAK U.S. Inc.

North and South American Headquarters
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak-us.com

SUBSIDIARIES

Australia

LINAK Australia Pty. Ltd
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.com.au

Austria

LINAK Repräsentanz - Österreich (Wien)
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.at

Belgium

LINAK Actuator-Systems NV/SA
(Belgium & Luxembourg)
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.be - www.fr.linak.be

Brazil

LINAK DO BRASIL COMÉRCIO DE
ATUADORES LTDA.
Phone: [phone] – 7070
Fax: [phone] – 7060
E-mail: [e-mail]
www.linak.com.br

C

anada

LINAK Canada Inc.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak-us.com

Czech Republic

LINAK C&S S.R.O.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.cz

Terms of use

The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and
up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes
without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any
particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or
other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.

Denmark - International

LINAK International
Phone: [phone]
E-mail: [e-mail]
www.linak.com

Denmark - Sales

LINAK DANMARK A/S
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.dk

Finland

LINAK OY
Phone: [phone]
E-mail: linak@linak.fi
www.linak.fi

France

LINAK FRANCE E.U.R.L
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.fr

Germany

LINAK GmbH
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.de

India

LINAK A/S India Liaison Office
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.in

Ireland

LINAK UK Limited (Ireland)
Phone: [phone]
Fax: [phone]
[phone] (UK Mobile)
[phone] (Republic Of
Ireland Mobile)
E-mail: [e-mail]
www.linak.ie

Italy

LINAK ITALIA S.r.l.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.it

Japan

LINAK K.K.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.jp

Malaysia

LINAK Actuators Sdn. Bhd.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.my - www.linak.co.id
www.linak.pk - www.linak.ph

Netherlands

LINAK Actuator-Systems B.V.
Phone: [phone] /
[phone]
E-mail: [e-mail]
www.linak.nl

Page 40 of 40

New Zealand

LINAK New Zealand Ltd
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.com.au

Norway

LINAK Norge AS
Phone: [phone]
E-mail: [e-mail]
www.linak.no

Poland

LINAK Polska
LINAK Danmark A/S (Spólka Akcyjna)
Phone: [phone] /
[phone]
E-mail: [e-mail]
www.linak.pl

Republic of Korea

LINAK Korea Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.kr

Russia

LINAK LLC
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.ru

Spain

LINAK Actuadores, S.L.u
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.es

Sweden

LINAK Scandinavia AB
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.se

Switzerland

LINAK AG
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.ch - www.fr.linak.ch
www.it.linak.ch

Taiwan

LINAK (Shenzhen) Actuator systems Ltd.
Taiwan Representative office
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.tw

Turkey

LINAK İth. İhr. San. ve Tic. A.Ş.
Phone: + 90 312 4726338
Fax: + 90 312 4726635
E-mail: [e-mail]
www.linak.com.tr

United Kingdom

LINAK UK Limited
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.linak.co.uk

DISTRIBUTORS

Argentina

NOVOTEC ARGENTINA SRL
Phone: [phone] / 8900
Fax: [phone]
E-mail: [e-mail]
www.novotecargentina.com

Colombia

MEM Ltda
Phone: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684
E-mail: [e-mail]
www.mem.net.co

India

Mechatronics Control Equipments India Pvt Ltd
Phone: [phone], 85
E-mail: [e-mail]
www.mechatronicscontrol.com

Indonesia

PT. HIMALAYA EVEREST JAYA
Phone: [phone]
Fax: [phone]
Fax (Sales): [phone]
E-mail: [e-mail]
www.hej.co.id

Israel

NetivTech LTD
Phone: [phone]
Fax: [phone]
Email: [e-mail]
www.netivtech.com

Russia

OOO FAM
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.fam-drive.ru

Singapore

Servo Dynamics Pte Ltd
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

South Africa

Industrial Specialised Applications CC
Phone: [phone]
E-mail: [e-mail]
www.isaza.co.za

United Arab Emirates

Mechatronics
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

LINAK 2018.05 MA-M9-02-783 LINAK A/S reserve the right to make technical alterations
©

Copyright