Page 1
PRODUCT DATA SHEET
TWINDRIVE
TM
TD1
Features:
• Angle footrest 45°± 3°
• Angle headrest 68° ± 3°
• Compatible with HB10 and HB20
• EOP in TD1 280 version
• Toroidal Transformer in TD1 280 and EI core
Transformer in TD1 220
• Duty cycle: 10% ~ 6 min. per hour max. 2 min.
continuous use followed by 18 min. not in use
• Max. speed: 0.58 RPM with max. torque
• Installation dimension: 796 mm length x 90 mm
height x 90 mm width. Installation dimension
on the shaft 581 ± 1 mm
• Colour: Grey plastic on motor
housing RAL 7035, closing
device Grey RAL 7016
• Ambient temperature:
+5°C to +40°C
• Storage and transport
temperature:
-10°C to + 70°C
• Approved according to EN 60335-1
• EMC according to EN55014 -1 / EN55014 - 2
• Low built-in height
• Low noise level
Options:
• Emergency lowering (2 x 9V batteries)
• External Mains cut-off
• Internal mains cut off (only TD1 220)
• 1 extra channels for an extra motor (analogue
systems)
• Up to 2 extra channels for extra motors (only
TD1 280 with memory and Infrared)
• Memory (only TD1 280)
• Memory and Infrared (only TD1 280)
• Black
The TWINDRIVE™ TD1 is a completely new
product, which is part of the Comfort furniture
group and has been produced to supply the
growing demands for motorised systems in the
leisure bed area.
TD1 is characterised by the very low built in
height, which makes it unique in this market
and gives much more free height under the bed
than previous systems for e.g. storage or easy
cleaning access.
Page 2
Dimension (mm):
Compatible actuators:
Actuators that are compatible with TD1:
LA27
LA31 with fast motor cannot be used in combination with TD1
Always choose LA27 and LA31 without brake otherwise there will it not be enough power in the 2 x 9 Volt batteries
for emergency lowering. In some cases where a standard HB is to run head, foot motor and the external actuator
simultaneous down it can happen that the actuator not will start if a brake is mounted. In the TD1 280 system with
memory and infrared the current cut-off down is not suffi cient to start up the extra actuator if a brake is chosen.
Cable for LA27
The cable used together with LA27 has to ordered separately:
LA27
(0705816)
Cable for LA31
The cable used in combination with LA31 is not possible to choose in the respectable ordering examples for the actuator. To
avoid any confusing write X when stating the cable and specify the cable as 0705825.
LA31
(0705825)
LA31
Page 3
Mounting instructions:
Mounting instructions for TWINDRIVETM:
Before mounting, both mounting brackets must be pulled out to their outer position by pushing them back.
This gives freedom of movement to the bed bracket.
Mounting is done by pushing the bed bracket into the TD1 unit and thereafter pushing the mounting brackets back again.
IMPORTANT one must be completely sure that the mounting brackets are in place before TD1 is used.
If the TD1 unit is mounted in the bed it will not be able to fall out if it is under load because the spindle nut is designed to
hold it in place.
Dimensions axle distance:
Page 4
Mounting instructions (welding):
For the TD1 it is important that one does not weld on the outside of the Twist Bracket because there is not room for a
welding seam in the motor housing. One may weld the bracket along the whole length of its ends.
Welding diagram:
To maintain the correct angle of rotation of the head rest and the foot rest it is important that the Twist bracket is welded
according to the above instructions. Non compliance with the instructions could lead to a smaller angle of rotation or in a
worst case damage to TD1.
Dimensions drawing of the twist bracket:
LINAK part number 0701030
Page 5
Initialisation of the TD1 memory and infrared system.
To ensure optimum drive of the systems with memory, infrared and extra channels must be
run out to the outward position and in again before use. This drive (out + in) must be done
without stops.
Removal / fi tting of the 9V batteries:
Changing of the 9V batteries is possible by pushing the batteries upwards via the two holes in the bottom of the unit.
It is necessary to use a blunt instrument with a diameter of Ø6 mm. When the batteries are visible from above they can be
removed by using fi ngers.
Important, before removal remove the battery clips. Fitting is done by pushing the batteries into the holes remembering
that the clips must be uppermost and that they are fi rst connected when the batteries are in place.
If the battery option is chosen the system will be able to be lowered into the reset position by using the reset button on the
handset during power failure.
This function is only available for the head and foot rest and only when the emergency lowering function is an available
option.
Page 6
Speed diagram:
300
250
200
150
Torque [Nm]
100
50
0
0 10203040506070
Torque on testrig for Twindrive
220 Nm / 280 Nm
Twindrive 280
Twindrive 220
Degrees above horisontal [°]
65
Maximum torque occurs with a non-linear load as prevails under use in a leisure bed. That is to say large torque during
start, which lessens as the backrest is raised. This is also how the TD1 has been tested.
Speed curve for the TD1 analogue versions:
TWINDRIVE 1 - Speed
0,90
0,80
0,70
0,60
0,50
0,40
Speed [Rpm]
0,30
Twindrive 280
Twindrive 220
0,20
0,10
0,00
18 72 126 180 234 288
Torque [Nm]
220 Nm ~ 3500 N 280 Nm ~ 4500 N
Page 7
Technical specifi cations:
Type Spindle
pitch
(mm)
TD1 220 2.5 220 0,43 10
TD1 280 2.5 280 0,56 10
The above measurements are made in connection with internal control box and are average values.
Compability with standard handsets:
HB10 HB20 HB20 HB20
Analogue “00” Memory “B1” Memory “C1”
TD1 220 yes Yes no no
TD1 280 yes yes yes yes
Torsion
max.
(Nm)
Speed at
full load
(Rpm)
Receiver Transmitter
Duty cycle
(%)
TWINDRIVE™ TD1 220:
Ordering example:
0
TD
1
1
0
A
0
0
0
0
0
0
0
0
Cable:
IP degree:
Mains cut-off:
Mains voltage:
Option:
Colour:
Emerg. lowering:
Channel:
Angle footrest:
Angle headrest:
Transformer:
Number of motors:
Type:
0 = Straight 3.2 m EU wall plug
3 = Straight 3.2 m UK wall plug
7 = Straight 3.2 m AUS wall plug
9 = Used together with ext. mains cut-off
0 = Standard
0 = None
1 = Mains cut-off with EU wall plug, black,
without non detachable cable 3.2 m
2 = Internal mains cut-off
0=230V
0 = None
A = Standard grey RAL 7035
B = black
0=None
1 = Emergency lowering via 9V battery
Incl. batteries
2 = Emergency lowering via 9V battery
Excl. Batteries
0 = None
0 = Standard 45 degrees
0 = Standard 68 degrees
1 = El-core transformer version
0 = Standard
1 = Only 1 motor for headrest
1=TD1
Twist bracket:
To be ordered separately
Page 8
TWINDRIVE™ TD1 280:
Ordering example:
0
0
1
TD
0
A
0
0
0
0
0
0
0
0
Cable:
IP degree:
Mains cut-off:
Mains voltage:
Option:
Colour:
Emerg. lowering:
Channels:
0 = Straight 3.2 m EU wall plug
3 = Straight 3.2 m UK wall plug
4 = Straight 3.2 m Japanese wall plug
5 = Straight 3.2 m US wall plug
7 = Straight 3.2 m AUS wall plug
9 = Used together with ext. mains cut-off
0 = Standard
0 = None
1 = Mains cut-off with EU wall plug, black,
without non detachable cable 3.2 m
2 = Internal mains cut-off
0=230V
1=120V
2=100V
0 = None
A = Prepared for IR connection
B = Prepared for memory and infrared
A = Standard grey RAL 7035
B = black
0 = None
1 = Emergency lowering via 9V battery
Incl. batteries
2 = Emergency lowering via 9V battery
Excel. batteries
0 = None standard
1=1
2 = 2 (only with memory and infrared)
It is the responsibility of the product user to determine the suitability
of LINAK A/S products for a specific application. LINAK will at point of
delivery replace/repair defective products covered by the warranty
if promptly returned to the factory. No liability is assumed beyond
such replacement/repair.
Angle footrest:
Angle headrest:
Transformer:
Number of motors:
Type:
Twist bracket:
Specifications subject to change without prior notice.
0 = Standard 45 degrees
0 = Standard 68 degrees
0 = Toroidal transformer
0 = Standard
1 = Only 1 motor for headrest
1 = TD 1
To be ordered separately
Copyright © LINAK 05.10. MA M9-02-088-E . Chapter 16.1
Loading...