LINAK LA36 DATA SHEET

PRODUCT DATA SHEET

ACTUATOR LA36

Features:

• 12, 24 or 36 V DC Permanent magnetic motor with resetable thermal overload protection

• Thrust from 500 N - 10.000 N depending on gear ratio and spindle pitch

• 10.000 N actuator cannot be ordered without electrical endstop

• 10.000 N actuator can be ordered in push now and pull from 01-09-207

• Max. speed up to 160 mm/sec. depending on load and spindle pitch

• Heavy duty aluminium housing for harsh conditions

• Highly efficient acme thread spindle

• Protection class: IP66 for outdoor use (dynamic), furthermore the actuator can be washed down by a high pressure cleaner (IP69K - static)

• Hand crank for manual operation

• Mechanical overload protection through integrated slip clutch (adjusted to 1.2 - 1.5 times max. load)

• Integrated brake, high self-lock ability

• End play – 2 mm max.

• Non rotating piston rod eye (turnable 0-90 degrees)

• Back fixture turnable in steps of 30 degrees

tic mot tection ing on gear

withou

push n

ding o

can b

Options:

• Built in end stop switches

• Adjustable magnetic sensors for end stop signals (code no. 1017031)

• Hall effect sensor with A/B –signal

• Potentiometer full scale at 333 mm stroke with 8 mm pitch, 500 mm stroke with 12 mm pitch and 833 mm with 20 mm pitch

• Different back fixtures and piston rod eyes

• Exchangeable cables in different lengths

Usage:

• Duty cycle at max. load 20% (up to 600 mm stroke, for strokes between 601-999 mm the max. duty cycle is 15%) at ambient temperature 25°C

• Ambient operating temperature -30°C to +65°C full performance from 5 - 40°C

LA36 is ideal for use in harsh conditions. It is our most solid actuator based on the philosophy that it must be able to operate under extreme conditions. The actuator is ideal for mobile “offhighway” equipment such as agricultural, forestry and construction machines.

Technical speciﬁ cations

LA36 with 12V motor

Order number Push max.

362CXXXXXXXXXXX 10000 10000 13000 13000 8 11 7 100 - 999* 4.5 22

363AXXXXXXXXXXX 2600 2600 3400 3400 12 40.7 30.6 100 - 999 4.5 21

363BXXXXXXXXXXX 4500 4500 5800 5800 12 23.1 17.8 100 - 999* 4.5 20.7

363CXXXXXXXXXXX 6800 6800 8800 8800 12 15.5 11.9 100 - 999* 4.5 21

365AXXXXXXXXXXX 1700 1700 2200 2200 20 68 52 100 - 999 4.5 22

365FXXXXXXXXXXX 500** 500** 1000 1000 20 160 135 100 - 999 4.5 20

LA36 with 24V motor

Order number Push max.

362CXXXXXXXXXXX 10000 10000 13000 13000 8 11 7 100 - 999* Not tested

363AXXXXXXXXXXX 2600 2600 3400 3400 12 41 32.3 100 - 999 2.4 10.4

363BXXXXXXXXXXX 4500 4500 5800 5800 12 23.3 18.9 100 - 999* 2.4 10.2

363CXXXXXXXXXXX 6800 6800 8800 8800 12 15.7 12.7 100 - 999* 2.4 10.3

365AXXXXXXXXXXX 1700 1700 2200 2200 20 68 52 100 - 999 2.4 10.3

365FXXXXXXXXXXX 500** 500** 1000 1000 20 160 135 100 - 999 2.4 10.0

LA36 with 36V motor

Order number Push max.

362CXXXXXXXXXXX 10000 10000 13000 13000 8 11 7 100 - 999* Not tested

363AXXXXXXXXXXX 2600 2600 3400 3400 12 41 33.5 100 - 999 2.0 8.0

363BXXXXXXXXXXX 4500 4500 5800 5800 12 23.3 19.1 100 - 999* 2.0 8.0

363CXXXXXXXXXXX 6800 6800 8800 8800 12 15.7 12.8 100 - 999* 2.0 8.0

365AXXXXXXXXXXX 1700 1700 2200 2200 20 68 52 100 - 999 2.0 8.0

365FXXXXXXXXXXX 500** 500** 1000 1000 20 160 135 100 - 999 2.0 8.0

* There are limitations on the stroke length if you need full load, please see “ LA36 Load v. Stroke Length” on page 2. ** Note: Fully loaded actuators need a softstart in order to prevent the clutch slipping at start (see curves).

(N)

Pull max.

(N)

Pull max.

(N)

Pull max.

(N)

*Self-lock

min. (N)

Push

*Self-lock

min. (N)

Push

*Self-lock

min. (N)

Push

*Self-lock

min. (N)

Pull

*Self-lock

min. (N)

Pull

*Self-lock

min. (N)

Pull

Pitch

(mm/spindle rev.)

Pitch

(mm/spindle rev.)

Pitch

(mm/spindle rev.)

Typical speed

(mm/s)

Load

Standard stroke

lengths (mm)

In steps of 50 mm

Typical amp.

(A)

12 V

no full No load Full load

Typical speed

(mm/s)

Load

Standard stroke

lengths (mm)

In steps of 50 mm

Typical amp.

(A)

24 V

no full No load Full load

Typical speed

(mm/s)

Load

Standard stroke

lengths (mm)

In steps of 50 mm

Typical amp.

(A)

36 V

no full No load Full load

Speed and current curves:

10.000N not tested

LA36 12V motor current v´s load

LA365A

LA363A

LA365F*

Ampere

0 2000 4000 6000 8000 10000 12000

LA36 24V motor current v´s load

Ampere

0 1000 2000 3000 4000 5000 6000 7000 8000

LA36 36V motor current v´s load

LA365F*

LA365A

8 7 6 5 4

Ampere

3 2 1 0

0 1000 2000 3000 4000 5000 6000 7000 8000

LA363C

LA363B

Load (N)

LA363A

Load (N)

LA363A LA363B LA363C

Load (N)

LA363B

LA362C

LA363CLA365ALA365F*

* Speed and current based on nominal power supply of 12, 24, 36VDC.

LA36 12V motor speed v´s load

180 160 140

LA365F*

120 100

LA365A

Speed (mm/s)

LA363A

40 20

0 2000 4000 6000 8000 10000 12000

180 160 140 120 100

80 60 40 20

0 2000 4000 6000 8000 10000 12000

180 160 140 120 100

80 60 40 20

0 2000 4000 6000 8000 10000 12000

LA363B

Load (N)

LA36 24V motor speed v´s load

LA365F*

LA365A

LA363A

LA363B

Load (N)

LA36 36V motor speed v´s load

LA365F*

LA365A

LA363A

LA363B

Load (N)

LA363C

LA362C

LA36

Ordering example:

363A11+00xxxA20

Cable:

IP-degree:

0 = No cable

1 = 1.5 m power cable (0367002-1500) 2 = 5 m power cable (0367002-5000) 3 = 0.2 m power cable with AMP connector (0367006) 4 = 1.5 m power and 1.5 signal (0367002-1500+0367003-1500) 5 = 5 m power and 5 m signal (0367002-5000+0367003-5000) 6 = 1.5 m Y-cable, power and signal in one (0367020)

2 = Standard (IP66)

Motor type: A = 12 V DC with clutch

B = 24 V DC with clutch

C = 36 V DC with clutch

Stroke length: XXX = mm Acme spindle:

100, 150....999 mm

Feedback: 0 = Standard (No feedback)

H = Hall signal

P = Potentiometer (not possible with CS36)

End stop: 0 = No limit switches (not for spindle 2 and A)

1 = With limit switches 2 = With limit switches and end-stop signals 3 = CS36 4 = CS36 with end-stop signals 5 = With potential free limit switches

Safety nut: + = Without safety nut - Standard

S = With safety nut - only in push

Piston rod eye: 0 = M20 X 1 female adapter - 0361016

1 = ø 12.9 mm hole, for 1/2" pin - 0361018-B 2 = ø 12.2 mm hole, for 12 mm pin - 0361109-B 3 = M12 X 1.75 male adapter - 0361224 4 = M16 X 1.5 male adapter - 0361135 5 = ø 12.2 hole with slot (like LA34) - 0361138

Back fixture: 0 = M20 X 1 female adapter - 0361128

1 = ø 12.9 mm hole, for 1/2" pin - 0361129 2 = ø 12.9 mm hole turned 90°, for 1/2" pin - 0361129 3 = ø 12.2 mm hole, for 12 mm pin - 0361119 4 = ø 12.2 mm hole turned 90°, for 12 mm pin - 0361119 5 = M12 X 1.75 male adapter - 0361126 6 = M16 X 1.5 male adapter - 0361247 7 = ø 12.2 hole with slot (like LA34) - 0361140 8 = ø 12.2 hole with slot (like LA34) turned 90° - 0361140

Gearbox:

Spindle type:

8 mm pitch 12 mm pitch 20 mm pitch

A = Gear ratio 1 : 18 N.A. 2.600 N 1.700 N B = Gear ratio 1 : 31 N.A. 4.500 N N.A. C = Gear ratio 1 : 46 10.000 N 6.800 N N.A. F = Gear ratio 1 : 7 N.A. N.A. 500 N

2 = 2-threaded acme spindle (8mm pitch) 3 = 3-threaded acme spindle (12 mm pitch) 5 = 5-threaded acme spindle (20 mm pitch) A = 2 + adjustable reed limit switches (on outer tube) C = 3 + adjustable reed limit switches (on outer tube) E = 5 + adjustable reed limit switches (on outer tube)

Actuator type: 36 = LA36

+ 5 hidden pages