Page 1
COLOR TFT LCD MONITOR
User Manual
Page 2
General Information
Thank you for choosing our TFT LCD (liquid crystal display) monitor. This product
employs integrate circuits, low power consumption, and no radiation emission. It has
fashion designed appearance and good portability. The TFT LCD screen is the most
suitable display for VGA, VCD, DVD, and GPS on vehicles or vessels. Moreover,
this product is able to be used in office, at home, or other proper positions. Please
enjoy the benefits of convenience, safety, and space-saving from this TFT LCD
monitor in different ways.
To ensure the best use of this product, please read this manual carefully
beforehand.
CAUTIONS
1. Please use the adapter attached in the accessories.
2. Please do NOT expose this product to direct sunlight, heat, or humid
conditions.
3. Please keep away from strong light while using this product in order to obtain
the clearest and the most colorful pictures.
4. Please avoid heavy impact or drop onto the ground.
5. Please do NOT use chemical solutions to clean this product. Please wipe with a
clean soft cloth to maintain the brightness of the surface.
6. Please follow the instructions and trouble-shootings to adjust the product. Other
improper adjustment may result in damage. Any further adjustment must be
performed or conducted by a qualified technician.
7. Please unplug the power and remove the battery if long-term no-use, or thunder
weather.
YP-01110801
Page 3
Table of Contents
1. PRODUCT DESCRIPTION -----------------------------------------
2. REMOTE CONTROL-------------------------------------------------
3. POWER SOURCE ----------------------------------------------------
4. BATTERY INSTRUCTION-----------------------------------------
5. SETTING MENU -------------------------------------------------
6. ACCESSORIES --------------------------------------------------------
7. PARAMETER ----------------------------------------------------------
8. TROUBLESHOOTING ----------------------------------------------
9. REMARK---------------------------------------------------------------
Page 4
1
1. PRODUCT DESCRIPTION
1．Infrared signal receiver (work with remote control)
2．Battery indicator light: red while standby; green while working
3．–: Volume down, or value down while using menu setting functions
4．+: Volume up, or value up while using menu setting functions
5．MENU：To activate OSD (on-screen display) menu; Long-press to switch
overscan / underscan pictures when receiving HDMI or SDI signal.
6．<: To select items on OSD menu; Press to switch the image monochrome
(red、green、blue、monochromatic and color); Long-press to achieve
full-screen display
7．>: To select items on OSD menu; Press to adjust brightness among 6
levels .Long-press for 5-6 seconds to achieve 5D camera mode under
HDMI function.
8．A/V: circularly switch among HDMI, YPbPr, Video 1, Video 2, and SDI
(optional).
9． Power ON/OFF switch. （Reboot to restore normal screen mode）
10．Sun shade.
Page 5
2
11．Mounting socket (right side)
12．SDI (Serial Digital Interface) signal input
13．SDI signal output
14．Y signal input
15．Video 1 signal input
16．Pb signal input
17．Video 2 signal inpu
18．Pr signal input
19．Audio signal input
20．Battery power on/off switch
Page 6
3
21．HDMI (High Definition Multimedia Interface) signal input
22．4-pin XLR DC power input
23．DC power input
24．Battery slot
25．Mounting socket (bottom)
2. REMOTE CONTROL
1．Power
2．Mute button
3．Display switch among HDMI、YPbPr、Video 1, Video 2, and SDI
(optional, must with necessary equipment) circularly
4．MENU: enter menu function setting
5．▲: Up move; or change brightness among 6 levels
6．▼: Down move
7．◄: Left move; or volume down; or increase the function values in
menu settings
8．►: Right move; or volume up; or decrease the function values in
menu settings
Page 7
4
3. POWER SOURCES
This product package comes with a 12V DC adapter plug in to the DC power
input (See PRODUCT DESCRIPTION 23).
Another option of power source is using batteries. The product package comes
with two types of batter slots (See BATTERY INSTRUCTION). The recommended
batteries are Panasonic DU21 and Sony QM91D.
Also, this product is capable to use the power from your camcorder via the 4-pin
XLR interface (See PRODUCT DESCRIPTION 22).
4. BATTERY INSTRUCTION
1．Battery slot and battery
The included two battery slots available for two types of batteries (See the
pictures below).
Picture: two types of battery slots
Picture: two types of batteries corresponding to the upper two slots
Page 8
5
2．Battery power control
The battery switch controls whether to use battery power or not. Keep off while not
using battery.
Suggestion: Better take off the battery for long-time not using this product.
2．Battery volume
An icon of battery volume displays on the screen while using battery as power source.
5. SETTING MENU
Before setting the menu functions, please make sure the device is connected
correctly.
When power on, press MENU on the device (See PRODUCT
DESCRIPTION 5) or on the remote control (See REMOTE CONTROL 4). The
menu of function setting will display on the screen.
Press >/< buttons on the device or ▼/▲ buttons on the remote control to
select items on the left of the display. Then press + / – buttons on the device or
►/◄buttons on the remote control to change the values.
20. Battery Switch
Battery power low
Battery power full
Page 9
6
The following pictures are the setting displays of different modes.
1．OSD YPbPr/HDMI/SDI setting menu
Picture: YPbPr/HDMI/SDI setting screen
2．OSD AV setting menu (Video 1/Video 2)
The auto-detected AV format displays at the bottom of the screen.
Picture: AV setting screen
3．Miscellaneous setting menu under YPbPr/HDMI/SDI modes, enter via
item to a new page.
Picture: Miscellaneous setting screen
Page 10
7
4．Icon description:
Icon
Name
Function
Brightness
Adjust the level of brightness
Contrast
Adjust the level of contrast
Saturation
Adjust the level of saturation
Tint
Adjust the tint of image
OSD H-Position
Adjust the on-screen-display horizontally
OSD V-Position
Adjust the on-screen-display vertically
Reset
Select “Yes” to reset the adjustment as
manufacture parameters.
Color temperature
Choose the color temperature. Options:
User, 6500ºK, 7500 ºK, or 9300 ºK.
Red
Note: Only can available under “User”
mode to meet the color value you need.
Green
Blue
Language
Choose language between English and
Chinese
Miscellaneous
Enter to next page (See picture below) for
miscellaneous selections
Exit OSD
Select “Exit” to quit the on-screen-display
menu.
Picture over-turn
horizontally
Horizontally over-turn picture to left or
right.
Picture over-turn
vertically
Vertically over-turn picture up or down.
Display mode
Shift display mode between 4:3 and 16:9.
Sharpness
Adjust the sharpness of picture
OSD Duration
Adjust the display duration of OSD from
5-100 seconds.
Page 11
8
6. Accessories
Picture: Accessories included in the product package
On the above picture, from top to bottom, left to right, the included
accessories are:
Remote control 1 piece
Bracket 1 piece
4-pin battery slot 1 piece
2-pin battery slot 1 piece
Sun shade 1 piece
User manual 1 piece
12V DC adapter 1 piece
Picture: Optional accessories
The optional accessories on the above picture are shoe mount, battery, and
HDMI cable.
Page 12
9
7. MAIN PARAMETERS
Panel Size
7’’ TFT LED (16:9)
Screen Resolution
800×480
Brightness
450cd/㎡ or 250cd/㎡
Contrast
500 : 1
Viewing Angle
140°/ 120°(H/V)
Input Voltage
DC 12V
Input Signal
HDMI, YPbPr, AV, SDI (optional)
Current
650mA
Standby Current
≤ 50mA
Power Consumption
≤ 8W
Input Resistance
75Ω
Input Frequency
H/30-60KHz,V/60-75Hz
Speaker
1 (front)
Speaker Power
1W
Size:(long × wide × high)
188mm × 131mm × 33mm (without sun shade)
194mm × 134 mm × 73mm (with sun shade)
Weight
510g / 568g (with sun shade)
8. TROUBLE SHOOTING
1. Only black-and-white display:
Check whether the color saturation and brightness are properly setup.
2. Power on but no pictures:
Check whether the cables of Video, HDMI, DVI (Digital Visual Interface), and/or
SDI (optional) are correctly connected. Please use the standard power adapter
coming with the product package. Improper power input may cause the device.
3. Wrong or abnormal colors:
Check whether the cables are correctly and properly connected. Broken or loose
pins of the cables may cause a bad connection.
4. Remote control doesn't work:
Check whether the battery is well charged and properly installed into the device.
The signal of the remote control may interfered by some obstacles or obstructions.
5. Other problems:
Please press “MENU” button and choose to reset to manufactory default
values.
Page 13
10
9. REMARK
It is normal to see some bright lines appear on the screen when turn off the device.
Note: due to constant effort to improve products and product features,
specifications may change without notice.
Loading...