Lightolier 1104SIC User Manual
Lytecaster
®
Recessed Downlighting 1104SIC
Page 1 of 1 6 3/4” Aperture 0
1104SICN
(Integral Nail)
1
2
6
6 3/4" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
7
5
4
1104SIC
(Integral Screw)
3
®
Shallow Incandescent Convertible IC/Non-IC Frame-In Kit
Overall Length
1104SIC/N: 10 3/4”
13” Min.
24” Max.
Top View
Height
1104SIC/N: 5 1/2”
Overall Width
1104SIC/N
: 7 5/16”
Frame-in Kit
Reflector Trim
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
1104SIC
1104SICN
Basic White Baffles
B16 B17
Open Downlight
B17WH
Features
1. Housing: .032” (#20 ga.) Aluminum. UL listed convertible IC/NON-IC. 2”
vertical adjustment in ceiling. Can be removed for access to junction box and
ceiling plenum. 5 1/2” tall for use in 2” X 6” joist construction and shallow
plenum applications. AirSeal® housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces heat
loss and condensation in ceiling.
2. Mounting Frame: .048” (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box: 2” X 4” X 3 1/2” (22 cu. in.) .032” (#22 ga.) galvanized steel.
UL listed for maximum of 8 (#12 ga.) 1104SIC/N and 6 (#12 ga.) 1004SIC/N
90°C through branch circuit conductors. Integral cable clamps permit
attachment of non-metallic (#12 or #14 ga.) Romex® cable without tools or
additional connectors.
4. Mounting Bars: .059” (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate
16” to 24“ O.C. joist spacing. Bars can accommodate 9” O.C. joist spacing
after a slight field modification (See Instruction Sheet). 1104SIC features
integral self-tapping phillips screws for secure attachment to wood or metal
construction. The 1104SICN features integral nails for secure attachment to
wood. Both attach to T-bar ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket: Porcelain medium base; nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 Volt 200° C) leads to junction box.
7. Thermal Protector: Meets NEC and UL requirements. Located inside housing.
Options & Accessories
AirSeal® Kit: LAS56
Note: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible; Suitable for Damp Locations),
Complies with Air Leakage Requirements stated in the Model Energy Code,
California Title 24 and the Washington State Energy Code.
AirSeal® is a registered trademark of Lightolier.
Romex® is a registered trademark of General Cable Industries Inc.
US and Foreign Patents Pending.
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Enclosed
Diffuser
1178LX
1177LX
Lightolier a Genlyte company www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • F0906
Loading...