Lightolier 1102TM User Manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
his fMIIre i5 intendedfor installationin accwdama w“hhthe NationalElsctrkal Code and local
)gulations.ToassurefullmmplisnoswithIccalCC& sndregulations,checkwithyour!ccsleleclrkd
Ispectorbeforeinstallation.Topreventelectrkalshodr,tumoffelecbidlyatfuseboxbeforepromeding.

Retaintheseinstructionsfor maintenancereference.

INSTALLATION OF PRE4WRED COMPACT

‘“

FLUORESCENT EMERGENCY LIGHTING DOWNLIGHTS

120 VOLT-(1 102TM1)
277 VOLT-(1 102TM2)

INSTRUCTION SHEET NO.

IS:1102TM

DSS2

Page10f4

I

lMPORTlh~T SAFEGUARDS

READ AND FOLLOW “ALL SAFETY IN=RUCTIONS

When using electrical equipment, basic safety precautions should always be followed; includlng the
followlng

1.00 not Install insulation within 3 inches of fixturse eides or wiring compartment, nor above fixture in
such a manner to entrap heat.

2. Turn off AC power before proceeding.

3. Ss eura all electrical connections era complete end the junction box is closed before Unit Connector
(located in the BWITCH/lNDICATOR LIGHT BOX) is connected.

4. DC not use outdoors.

5.00 not let power eupply cords touch hot surfaces.

6.00 not mount near gee or electric heaters.

7. Use caution when servicing batterfee. 00 not incinerate or mutilatq may burst or raleess toxic materiel.

00 not ehorf circuit may cause bums. Battery acid can cause bums to skin end ayes If acid is spilled

on skin or in eye~ flueh acid with fresh water end contact a physician immediately.

S. Equipment should be mounted in Iocatione end at a height whete it will not readily be eubjactad to

tampsrfng by unauthorkd personnel.

9. The use of eoceeeay equipment not recommended by the manufacturer may cause en uneefe condition.

10.00 not use thie equipment for other then intendad use

11.Thie unit has more then one power eupply connection point. To reduce the rick of electrical ehook—
disconnect both normal end emergency power suppliee before aewicing.

12. Safora servicing, to prewnt electric ehoc~ make sure the unit connector of the EMERGENCY PACK
(located in the ewitchfindicetor light box) IS disconnected, make certain that the ewitched (if the fixture

“is ewitched) end the unewitchad line to the EMERGENCY PACK is turned off at the fuss box.

Servicing ehould be performed by quaNfiad sswice personnel only.

FIG.A

A. FRAME -IN

1.1<3

SAVE THESE lNSrRUCrlONS

T,pgv

FIG.B FIG.C

B. CLOSE -IN C. PULL - THRU D. PUSH -UP E. SNAP -IN

FIG.D

FIG.E

I“BTC>B.IE wRR%!ywiy%tR

A. FRAME-IN

Featen MOUNTING FRAME to wood joist. Line up
bottom edge of ADJUSTABLE MOUNTING BAR
with bottom of wood. joist (Fig. 5). Wire to supply
leads. (For Cable, use built-in Cable Clsmp in
J-Box.)

1s:1I02TM

Oaez
Page20f4

ME

NOTf& 1. ADJUSTABLE MOUNTING BARS are pre-

assembled on long aide of MOUNTING
FRAME for ri idity and ease of installation,
Fig. 5. The M UNTING BARS must be

8

n?rnoved and installed on narrow side of
MOUNTING FRAME if installed between

joist on 16mspacing, Fig. 6.

2. MOUNTING BARS can be extended to 24”;
the MOUNTING FRAME can be mounted
off -center.

3. For euepended ceilin s, make certain that
bottom of MOUNTIN FRAME is no higher

8

than 1“ above ceiling Iinej Fig. 7.

FIG. 5

=SW,TCH INDICATOR

–.

L>z~, ~p~~~

FIG. 7

WIRING

1. Make sure AC power is off at the fuse box.

2. AC BALLAST AND EMERGENCY SALLAST must be fed from the same branch circuit.

3. In switched fixtures the EMERGENCV BALLAST muet be connected ahead of any local switching.

4. This f!xturs is prewired
.Junctlon BOX. See wiring diagram (Fig. 8).

5. Be sure all electrical connections are made and the JUNCTION BOX is cloeed before comectin9
UNIT CONNECTOR in SWITCH/lNDICATOR LIGHT BOX. M

Jc&

%?

for 120V or 277V. Check marking cm fixture before making connections in

w=ggw

Box

FIG. a

SOCI$ET