Models 33LM, 33LMC,
61LM, & 61LMC
To prevent possible SERIOUS INJURY or
Models 62LM & 62LMC
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of
reach of children. NEVER permit children
Models 33LM, 33LMC
63LM, & 63LMC
to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted, and
Models 64LM & 64LMC
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
INTRODUCTION
This product is for use with gate operators, commercial door operators and any LiftMaster® product
that uses a 390 MHz fixed code. The single-button remote control will activate one device, the
2-button remote control will activate up to 2 devices, and the 3-button remote control will activate
up to 3 devices.
BEFORE YOU BEGIN
Locate the dip switches on your remote control
Single-Button and 3-Button Remote Controls:
Slide the battery cover open to access the dip
switches in the remote control.
Single and 3-Button Remote Controls
123456789
+0–
2-Button Remote Control:
The 2-button remote control has two sets of
dip switches.
Slide the battery cover open to access the dip
switches for the smooth button. Remove the
screw on the back of the remote control and
remove the cover by pressing the tab. This will
access the dip switches for the ribbed button.
3-Button Mini Remote Control:
The large top button is recommended for use with
a garage door opener and/or light control product.
The other push buttons can be used to operate
another garage door opener and/or light control
product.
Access the dip switches by turning the remote
over and removing the back of the case. Be
careful to avoid moving circuit board components.
2-Button Remote Controls
+0–
Tab
+0–
Mini Remote Controls
123456789
123456789
123456789
+0–
1
PROGRAMMING
Use a pen or screwdriver to slide the dip switches.
Programming the remote control to an
existing remote control
Locate the dip switches in the new and old
remote controls. Place remote controls side by
side and set the dip switches in the remote
controls to matching positions (+,0,-).
New Remote Control
+0–
Existing Remote Control
=
123456789
+0–
123456789
Programming a 3-button remote control
When programming a single or 2-button remote
control to a 3-button remote control it is very
important to set dip switch #1 to the correct
position. The dip switch in the single or 2-button
remote control MUST correspond to the buttons
on the 3-button remote control as shown.
Example: If you are programming a
single-button remote control to the middle button
on the 3-button remote control, dip switch #1 in
the single-button remote control MUST be set to
“0” in order for both buttons to work.
Programming the remote control
without an existing remote control
Set the dip switches in the remote controls to
any position you want (+,0,-).
Programming with Smart/Learn button
Press and release the Smart/Learn button
1
on your product. The LED will light.
Within 30 seconds press and hold the
2
button on the remote control that you
wish to activate your product.
Programming is complete.
Repeat the steps above for each button and/or
remote control you would like to program.
Single or 2-Button
Remote Control
+0–
Dip switch #1 must
correspond to the 3-button
remote control buttons
New Remote Control
+
0
–
123456789
1
Smart/Learn Button
=
123456789
3-Button
Remote Control
123456789
+0–
+
0
2
-
Programming with dip switches
Check the dip switch settings on the back of
1
your product.
Use a pen or screwdriver to slide the dip
2
switches in the remote control to match the
dip switches on the back of the product.
When the dip switches have been set press the remote
control button to activate your product.
2
Dip Switch Settings
From Product
+0–
=
123456789
New Remote
Control
123456789
+0–
PROGRAMMING MODEL 33LM ONLY
Install the control station and receiver where the door is visible, but away from the door and its
hardware. When a receiver is used to activate a commercial door opener, a reversing edge MUST
be installed on the bottom of the door. Failure to install a reversing edge under these
circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
Model 33LM 3-button remote controls can also be used with a 423LM 3-channel receiver and a
3-button door control to activate a commercial door operator in OPEN, CLOSE, and STOP mode.
Use a screwdriver to pry open the receiver
1
cover.
Verify that the slide switch on receiver is
2
set to the N.C. position (other wise the
commercial door operator will not
operate).
Press and release the Smart/Learn button
3
labeled “A” on the receiver. The adjacent
LED will flash.
Within 30 seconds press and release the
4
red button on the remote control. The red
button is now programmed for CLOSE
mode.
NOTE: If the remote control button is not
pressed within 30 seconds, the LED next
to the selected Smart/Learn button will
turn OFF. In that case, press the
Smart/Learn button again to repeat
programming.
1
2
N.C.
Slide
Switch
“A” Smart/Learn Button
4
3
Repeat the steps 3-4 above with the yellow button on the remote control and the receiver
Smart/Learn button “B” to program the CLOSE mode; and again with the green button on the remote
control and the receiver Smart/Learn button “C” to program the OPEN mode.
Replace the receiver cover.
5
3
5