Lift-Master 535-315LM User Manual

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate

or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

WARNING

Universal Radio Control

OWNERS MANUAL

Model 535-315LM SECURITY✚ Receiver Only

Mounting Receiver

• Unplug the opener before proceeding.

• Fully extend antenna wire below bottom of case as shown.

• The receiver can be mounted directly on the door opener with

the clips provided. Figure 1.

• Attached to a ceiling/inside wall of the garage with connecting bell wire (not provided). Fasten the receiver to the ceiling or inside garage wall with dry wall screws provided. Figure 2.

NOTE: Transformer Model 85 is required if your residential garage door opener is a LiftMaster, Chamberlain or Sears.

Installation Using Clips

Loosen the three terminal screws on the receiver (labeled 1, 2 and 3) Figure 1. Insert one end of a mounting clip under each terminal. Do not retighten at this time.

Loosen the three terminal screws on the opener used for push button controls and radio power.

Leaving the push button bell wire in place, insert the other ends of the mounting clips under the opener terminal screws.

NOTE: If the number sequence of opener terminals doesn't match the receiver, turn the receiver around (so back is facing out) and complete the connection.

Retighten the terminal screws on opener and receiver. Reconnect power to the opener. The receiver push bar should light. If it does not, use Transformer Model 85.

Installation Using Bell Wire

Attach one end of 3-strand bell wire (not provided) to receiver terminals 1, 2 and 3. Connect the other end to the three opener terminals used for push button controls and radio power. Use insulated staples to secure bell wire between receiver and opener. Figure 2.

Reconnect power to the opener. The receiver push bar should light. If it does not, use Transformer Model 85.

Installation With Transformer Model 85

With the transformer, use a 2-wire connection only. Attach wire to receiver terminals 1 and 2 and to the opener terminals used for push button control. Plug the transformer into receiver and 120 Volt outlet. Figure 3.

Antenna Wire Fully Extended

Radio Power

Push Button

Common

Opener Terminals

Antenna Wire Fully Extended

Radio Power

Push Button

Common

Opener Terminals

Push Button

Programming the Remote to the Receiver

With SECURITY✚, the code between the remote control and the receiver changes with each use, accessing over 100 billion new codes.

You can activate your opener with up to 8 SECURITY✚ remote controls, and one SECURITY✚ Keyless Entry.

1. Pry open the front panel of receiver case with a coin or a screwdriver. Re-connect power to opener.

2. Press and release the “learn” button on the receiver. The learn indicator light will glow steadily for 30 seconds.

3. Within 30 seconds, press and hold the button on the handheld remote that you wish to operate your garage door.

The opener will now operate when the push button on either the receiver or the remote control transmitter is pressed.

Repeat Steps 2 and 3 for each remote control that will be used to operate the garage door opener.

To Erase all Remote Control Codes

Press and hold the “learn” button on the receiver panel until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to reprogram each remote control.

Set Output Duration

(Commercial APPLICATIONS Only)

For commercial applications, the receiver can be set for either constant or momentary closure on the output contacts. Use of constant closure is prohibited on residential garage door openers because it overrides the safety reversal devices.

With the jumper in the “M” (Momentary) position, the contacts will close for 1/4 second regardless of the length of radio transmission. With the jumper in “C” (Constant) position, the contacts will stay closed as long as the radio continues transmitting.

The receiver is factory set at M.

To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED.

WARNING

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SPECIFICATIONS

Output Rating......................................5 Amps 28VAC or DC Max.

Power ....................................................18V - 30V ~, 30mA, 60Hz

18 - 30V , 30mA

RF Frequency....................................................................315MHz

If the power is other than shown in specifications, Accessory Transformer Model 85 or 95 is required.

Accessory Transmitters — Series 50, 60, 70, 80 and 900.

Indicator Light

Learn Button

Option Jumper

WARNING

CONSTANT OPERATION

Output Duration Terminals

Jumper

MOMENTARY OPERATION

Output Duration Terminals

Jumper

+ 2 hidden pages