LifeShield HSC1000 User Manual

Handset and Charger Installation
Instructions

Model HSC2000 Handset Kit

InGrid Handset Kit Contents

HSC1000 Handset
CHC1000 Charging Cradle
PSC0101 Power Supply
Belt Clip
IG80 Ni-MH Rechargeable Battery Pack

Install the Handset and Charger

Connect Battery Pack -- The battery pack is

shipped in the Handset, but it is not connected.
a) Open the battery compartment and remove

the battery

b) Insert the battery plug into the two-pin jack,

and insert the battery.

Attach Belt Clip – Snap the Belt Clip onto the
sides of the Handset.

Connect Charging Cradle – Connect the
Charging Cradle power supply to the bottom of
the charging cradle and to the electrical wall
outlet.

Note: The jack is keyed so that the plug can
only be inserted in one direction. Be careful not
to crimp wire.

c) Replace the battery cover.
d) The handset display will illuminate when

battery is connected.

Note:

o Use only InGrid IG80 rechargeable battery packs

supplied with your various Home Protection
components.

o Replacement battery packs are also available

through the InGrid’s customer service at 1-877­INGRID7 or on-line at www.InGridHome.com
only the supplied AC power adapter. Do not use
any other adapter.

Use

o Place the power cord so that it does not create a

trip hazard or where it could become pinched and
create an electrical hazard.

o Do NOT use AC power outlets that are controlled

by a wall switch

Charge Handset – Place the Handset in the
Charging Cradle. When properly seated on the
cradle, the amber light on the front of the cradle
will be illuminated.

1. Immediately place the Handset in the Charging Cradle
that came packed with the Handset. THE HANDSET

MUST CHARGE AT LEAST 2 HOURS PRIOR TO
ATTEMPTING ANY SECURITY SYSTEM
INSTALLATION. IT MUST CHARGE 12 HOURS
BEFORE MAKING PHONE CALLS.

2. The phone system comes with various settings pre­defined from the factory. Should you want to change
these settings we suggest waiting until after you
activate your system. These settings include, ring
tones, ring volume, distinctive ringing, display contrast
etc.

Add the Handset to your InGrid
System

These devices may be added to the InGrid
System up to the number shown in the table:

Device Device

Maximum

System

Maximum
Handsets 6
Consoles 4 9*
Grid Extenders 4

*The system will allow a maximum of 9 Handset/Console or
Grid Extender combinations

After the Handset and Charger are installed, use
a Handset or Console that is already registered
on the System to enter the Security Menu and
follow the steps for installing new hardware.

Enter the Security Menu

After installing the hardware, enter Menu on
your Handset or Console.

o Scroll to Setup and press SELECT
o Scroll to Security and press SELECT
o Enter Master Code and press SELECT

Add the Handset

1. Using the scroll and SELECT buttons on

your existing Handset or Console, navigate
to GC or Handset (Menu/Setup/Security/GC
or Handset/<Add New>).

GCs or Handset

<Add New>

SELECTBACK

2. Press the SELECT key to <Add New>. The

system will begin searching for the new
Handset or Console you are looking to add.

3. On the New Handset or Console press the

SEARCH key.

4. The system will inform you when it has

found and added the Handset via the display
and an audio signal. Press OK when you

5. You will then be given the option to edit the

FCC Information

FCC Part 15

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

CAUTION:

Changes and modifications to this product not expressly
approved by InGrid, Inc. could void not only the user’s
authority to operate this device, but also the limited warranty.

Note:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, three is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:

Some cordless telephones operate at frequencies that may
cause interference to nearby TVs or VCRs. To minimize or
prevent such interference, the base or the cordless
telephone should not be placed near or on top of a TV or
VCR. If interference is experienced, move the cordless
telephone further away from the TV or VCR. This will often
reduce, or eliminate, interference. Consult an experienced

have been informed that the Handset or
Console has been added.

default name.

o Reorient or relocate the receiving antenna
o Reorient or relocate and increase the separation

between the equipment and receiver

o Connect the equipment into an outlet on a circuit

different from that to which the receiver is
connected.