Page 1
Operating instructions
Freezer for integrated use, door-on-door
120713
7082694 - 01
IGN ... 6
Page 2
Appliance at a glance
Contents
1 Appliance at a glance............................................ 2
1.1 Description of appliance and equipment.................. 2
1.2 Range of appliance use............................................ 2
1.3 Conformity................................................................ 3
1.4 Saving energy.......................................................... 3
2 General safety information................................... 3
3 Controls and displays........................................... 4
3.1 Operating and control elements............................... 4
3.2 Temperature display................................................. 4
4 Putting into operation............................................ 4
4.1 Transporting the appliance....................................... 4
4.2 Installing the appliance............................................. 4
4.3 Disposing of packaging............................................ 5
4.4 Connecting the appliance......................................... 5
4.5 Switching on the appliance....................................... 5
5 Control.................................................................... 5
5.1 Brightness of the temperature display...................... 5
5.2 Child proofing........................................................... 5
5.3 Door alarm................................................................ 6
5.4 Temperature alarm................................................... 6
5.5 Freezing food........................................................... 6
5.6 Thawing food............................................................ 6
5.7 Setting the temperature............................................ 6
5.8 SuperFrost............................................................... 6
5.9 Drawers.................................................................... 7
5.10 Shelves.................................................................... 7
5.11 VarioSpace............................................................... 7
5.12 Pull-out rails.............................................................. 7
5.13 Information system................................................... 7
5.14 Cold storage accumulators....................................... 7
5.15 IceMaker.................................................................. 8
6 Maintenance........................................................... 8
6.1 Defrosting with NoFrost............................................ 8
6.2 Cleaning the appliance............................................. 8
6.3 Cleaning the IceMaker............................................. 8
6.4 Customer service..................................................... 9
7 Malfunction............................................................. 9
8 Decommissioning.................................................. 10
8.1 Shut off the water intake........................................... 10
8.2 Switching off the appliance....................................... 10
8.3 Taking the appliance out of service.......................... 10
9 Disposing of the appliance................................... 10
The manufacturer works constantly on the further development
of all the types and models. Therefore please understand that
we have to reserve the right to make design, equipment and
technical modifications.
To get to know all the benefits of your new appliance, please
read the information contained in these instructions carefully.
The instructions apply to several models. Differences may
occur. Text relating only to specific appliances is marked with
an asterisk (*).
Instructions for action are marked with a , the results of
action are marked with a
.
1 Appliance at a glance
1.1 Description of appliance and equipment
Note
Shelves, drawers and baskets are arranged for optimum
u
energy efficiency on delivery.
Fig. 1
(1) Operating and control
elements
(2) NoFrost (7) IceMaker*
(3) Cold storage accumu-
lator
(4) Information system (9) Adjustable feet
(5) Type plate
(6) Drawers
(8) VarioSpace
1.2 Range of appliance use
The appliance is suitable solely for cooling food
in a domestic environment or similar. This
includes use in, for example
-
in staff kitchenettes, bed and breakfast establishments,
-
by guests in country homes, hotels, motels
and other forms of accommodation,
-
in catering and similar services in the wholesale trade
Use the appliance solely as is customary within
a domestic environment. All other types of use
are inadmissible. The appliance is not suitable
for storing and cooling medicines, blood
plasma, laboratory preparations or similar
substances and products covered by the
2007/47/EC Medical Devices Directive. Misuse
of the appliance can result in the stored products suffering harm or perishing. Furthermore,
the appliance is not suitable for operation in
potentially explosive atmospheres.
The appliance is set to operate within specific
ambient temperature limits according to its
2 * Depending on model and options
Page 3
General safety information
climate rating. The correct climate rating for
your appliance is indicated on the type plate.
Note
Compliance with the ambient temperatures
u
indicated is required, otherwise the cooling
performance is reduced.
Climate
rating
SN, N up to 32 °C
ST up to 38 °C
T up to 43 °C
for ambient temperatures
The appliance will function properly in ambient
temperatures of down to 5 °C.
1.3 Conformity
The refrigerant circuit is tested for leakage. When built-in the
appliance complies with the relevant safety regulations and EC
Directives 2006/95/EC, 2004/108/EC, 2009/125/EC and
2010/30/EU.
Note for test institutions:
Tests are to be carried out according to the applicable
standards and guidelines.
Preparation and testing of the appliances must be carried
out taking the manufacturer's loading plans and the
notes in the operating manual into account.
1.4 Saving energy
Always ensure good ventilation. Do not cover ventilation
-
openings or grille.
Do not place appliance in areas of direct sunlight or next to a
-
stove, heater or similar object.
The energy consumption depends on the installation condi-
-
tions, e.g. the ambient temperature (see 1.2) .
Keep the time the appliance is open to a minimum.
-
The lower the temperature setting, the higher the power
-
consumption.
Store food logically. (see Appliance at a glance).
-
Ensure that all food is well packed and covered for storage.
-
This will prevent frost from forming.
First cool warm food to room temperature before storing it .
-
2 General safety information
Danger for the user:
-
This appliance can be used by children of 8
years old and over, and also by persons with
restricted physical, sensory or mental
capacity or lack of experience and knowledge, if they are supervised or have been
instructed on safe use of the appliance and
understand the resulting risks. Children must
not be allowed to play with the appliance.
Cleaning and user maintenance must not be
carried out by children without supervision.
-
When disconnecting the appliance from the
supply, always take hold of the plug. Do not
pull the cable.
-
In the event of a fault pull out the mains plug
or deactivate the fuse.
-
Do not damage the mains power cable. Do
not operate the appliance with a defective
mains power cable.
-
Have any repairs to or intervention in the
appliance, and any change of the mains
power cable, carried out by the customer
service only or by other specialised personnel
trained for the purpose.
-
Only install, connect and dispose of the appliance according to the instructions.
-
Only use the appliance when it is installed.
-
Please keep these instructions in a safe place
and pass them on to any subsequent owners.
-
All repairs to and intervention in the IceMaker
may be carried out only by service personnel
or by other skilled personnel trained for the
purpose.*
-
The manufacturer is not liable for damage
caused by a faulty fixed water connection.*
Fire hazard:
-
The refrigerant R 600a is environmentally
friendly but flammable. Escaping refrigerant
may ignite.
•
Do not damage the refrigerant circuit pipes.
•
Do not allow naked flames or ignition
sources to enter the appliance.
•
Do not use any electrical appliances in the
interior (e.g. steam cleaners, heaters, ice
cream maker etc.).
•
If refrigerant escapes: remove any naked
flames or sources of ignition from the
leakage area. Ventilate the room well.
Notify the after-sales service.
-
Do not store explosives or sprays using
combustible propellants such as butane,
propane, pentane, etc. in the appliance. To
identify these spray cans, look for the list of
contents printed on the can, or a flame
symbol. Gases possibly escaping may ignite
due to electrical components.
-
Please be sure to store alcoholic drinks or
other packaging containing alcohol in tightly
closed containers. Any alcohol that leaks out
may be ignited by electrical components.
Danger of tipping and falling:
-
Do not misuse the plinth, drawers, doors etc.
as a step or for support. This applies particularly to children.
Danger of food poisoning:
-
Do not consume food which has been stored
too long.
Danger of frostbite, numbness and pain:
* Depending on model and options 3
Page 4
Controls and displays
-
Avoid lasting skin contact with cold surfaces
or refrigerated/frozen food or take protective
steps, e.g. wear gloves. Do not consume ice
cream, water ice or ice cubes immediately
and do not consume them too cold.
Danger of injury and damage:
-
Hot steam can lead to injury. Do not use electrical heating or steam cleaning equipment,
open flames or defrosting sprays to defrost.
-
Do not use sharp implements to remove the
ice.
Please observe the specific information in
the other sections:
DANGER identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note identifies useful information and tips.
The following displays indicate malfunction. Possible causes
and corrective action (see Malfunction).
-
nA
-
F0 to F5
4 Putting into operation
4.1 Transporting the appliance
Risk of injury and danger of damage as a result of incorrect
transport!
u
u
u
4.2 Installing the appliance
Risk of fire due to short circuit!
If the mains cable/connector of the appliance or of another
appliance touch the rear of the appliance, the mains cable/
connector may be damaged by the appliance vibrations,
leading to a short circuit.
u
u
CAUTION
Transport the appliance in a packed condition.
Transport the appliance upright.
Do not transport the appliance without assistance.
WARNING
Stand the appliance so that it is not touched by connectors
or main cables.
Do not plug the appliance or any others into sockets located
near the rear of the appliance.
3 Controls and displays
3.1 Operating and control elements
Fig. 2
(1) Temperature display (5) SuperFrost button
(2) Down setting button (6) Alarm button
(3) Up setting button (7) Child-proofing symbol
(4) On/Off button
3.2 Temperature display
The following are displayed in normal operation:
the warmest freezing temperature
-
The temperature display flashes:
the temperature setting is being changed
-
after switch-on the temperature is not yet cold enough
-
the temperature has risen several degrees
-
Dashes flash in the display:
the freezer temperature is above 0 °C.
-
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u
u
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flammable. Escaping refrigerant may ignite.
u
Fire hazard and danger of damage!
u
q
q
q
q
WARNING
The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
Only use the appliance when it is installed.
WARNING
Do not damage the piping of the refrigeration circuit.
WARNING
Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
In the event that the appliance is damaged, contact the
supplier immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed
to direct radiation of the sun, next to a cooker, heater and
similar.
Do not install the appliance without assistance.
4 * Depending on model and options
Page 5
Control
Standard EN 378 specifies that the room in which you install
q
your appliance must have a volume of 1 m2 per 8 g of R
600a refrigerant used in the appliance. If the room in which
the appliance is installed is too small, a flammable gas-air
mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance
is indicated on the type plate on the inside of the appliance.
Fit the appliance in stable kitchen units only.
q
The following ventilation gaps must be observed:
q
The depth of the ventilation channel at the rear of the unit
•
must be at least 38 mm.
There must be a ventilation space of at least 200 cm2 in
•
the plinth and at the top of the unit.
Basically the principle applies: the larger the ventilation
•
space, the more energy-saving the appliance is in operation.
Detach the connecting cable from the rear of the appliance,
u
removing the cable holder at the same time because otherwise there will be vibratory noise!
After installation:
Remove all transit supports.
u
Unscrew the red transport
u
lock. Close the vacated
retaining hole using the
stopper (60).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
Check the electrical connection.
u
Plug in the power plug.
u
4.5 Switching on the appliance
Press On/Off button
u
The temperature display flashes until the temperature is
w
sufficiently cold. If the temperature is above 0 °C, dashes
flash. If it is below, the set temperature flashes.
Fig. 2 (4)
.
5 Control
5.1 Brightness of the temperature display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
Dispose of packaging material (see 4.3) .
u
Note
Clean the appliance (see 6.2) .
u
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
Always see to good ventilation at the installation site.
u
4.3 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film!
Do not allow children to play with packing material.
u
The packaging is made of recyclable materials:
corrugated board/cardboard
-
expanded polystyrene parts
-
polythene bags and sheets
-
polypropylene straps
-
nailed wooden frame with polyethylene panel*
-
Take the packaging material to an official collecting point.
u
4.4 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
Do not use stand-alone inverters (conversion of d.c. to a.c./
u
three-phase) or energy saving plugs.
Fire and overheating hazard!
u
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
WARNING
Do not use extension cables or multiple socket outlets.
The brightness is adjustable between h1 (no illumination) and
h5 (maximum luminosity).
To activate the setting mode: press the SuperFrost button
u
Fig. 2 (5)
w
The display indicates c.
The SuperFrost button flashes.
w
Using the Up setting button
u
button,
To confirm: briefly press the SuperFrost button
u
To make the display brighter: press Up button
u
Fig. 2 (3)
To make the display darker: press Down button
u
Fig. 2 (2)
To confirm: press SuperFrost button
u
The brightness is adjusted to the new value.
w
To deactivate the set-up mode: press On/Off button
u
Fig. 2 (4)
-or-
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
w
display.
for about 5 s.
Fig. 2 (2)
, select h.
.
.
.
Fig. 2 (3)
Fig. 2 (5)
or Down setting
Fig. 2 (5)
.
.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 Setting the child lock
To activate the setting mode: press SuperFrost button
u
Fig. 2 (5)
w
The display indicates c.
The button SuperFrost flashes.
w
Briefly press the SuperFrost button
u
To switch on: Using the Up setting button
u
or Down setting button
To switch off: Using the Up setting button, freezer
u
compartment
freezer compartment
To confirm: press SuperFrost button
u
for about 5 s.
Fig. 2 (3)
Fig. 2 (5)
Fig. 2 (3)
Fig. 2 (2)
Fig. 2 (2)
, select c1.
or Down setting button,
, select c0.
Fig. 2 (5)
to confirm.
.
* Depending on model and options 5
Page 6
Control
When the child lock symbol
w
is activated.
To deactivate the set-up mode: press On/Off button
u
Fig. 2 (4)
-or-
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
w
display.
.
Fig. 2 (7)
shines, the child lock
5.3 Door alarm
If the door is open for longer than 60 seconds, the
audible warning will sound.
The audible alarm is automatically silenced when
the door is closed.
5.3.1 Muting the door alarm
The audible alarm can be muted when the door is open. The
sound switch-off function is active as long as the door is left
open.*
Press alarm button
u
The door alarm is silenced.
w
Fig. 2 (6)
.*
5.4 Temperature alarm
The audible alarm sounds if the freezer temperature
is not cold enough.
The temperature display flashes at the same time.
The cause of the temperature being too high may be:
warm fresh food was placed inside
-
too much warm ambient air flowed in when rearranging and
-
removing food
power failure for some time
-
the appliance is faulty
-
The audible alarm is automatically silenced and the temperature display stops flashing when the temperature is sufficiently
cold again.
Note
Food may be spoilt if the temperature is not cold enough.
Check the quality of the food. Do not consume spoiled food.
u
5.4.1 Muting the temperature alarm
The audible alarm can be muted. When the temperature is
sufficiently cold again, the alarm function is active again.
Press alarm button
u
The audible alarm is silenced.
w
Fig. 2 (6)
.
5.5 Freezing food
The rating plate indicates the maximum quantity of fresh food
you can freeze within 24 hours (see Appliance at a glance)
under "Freezing capacity ... kg/24h".
The maximum load for the top drawer is 5 kg and for the other
drawers 25 kg each.
The shelves can each be loaded with 35 kg of frozen food.
A vacuum is generated after the door is closed. After closing
the door, wait for about 1 minute and then it opens more easily.
CAUTION
Risk of injury due to broken glass!
Bottles and cans containing drinks may burst when being
frozen. This applies particularly to sparkling drinks.
Do not freeze bottles and cans containing drinks!
u
In order that the food is rapidly frozen through to the core, do
not exceed the following quantities per pack:
- Fruit, vegetables up to 1 kg
- Meat up to 2.5 kg
Pack the food in portions in freezer bags, reusable plastic,
u
metal or aluminium containers.
5.6 Thawing food
- at room temperature
- in a microwave oven
- in a conventional or fan oven
Food once thawed should be re-frozen only in exceptional
u
cases.
5.7 Setting the temperature
The appliance is pre-set for normal operation.
The temperature can be set between -14 °C and -28 °C, the
recommended temperature is -18 °C.
To set the temperature higher: press Up button
u
To set the temperature lower: press Down button
u
When the button is pressed the first time, the previous value
w
is indicated in the temperature display.
To change the temperature in 1 °C steps: briefly press the
u
button.
-or-
To change the temperature continuously: hold down the
u
button.
The value is displayed flashing during the setting operation.
w
The actual temperature is displayed approx. 5 seconds after
w
the button is last pressed. The temperature gradually
adjusts to the new value.
Fig. 2 (3)
Fig. 2 (2)
.
.
5.8 SuperFrost
With this function you can freeze fresh food quickly
through to the core. The appliance operates with
maximum refrigeration. The noise of the refrigeration
unit may be temporarily louder as a result.
The maximum amount of fresh food which can be frozen in 24
h is indicated on the type plate under "freezing capacity ... kg/
24h". This amount varies according to the model and climate
rating.
You have to activate SuperFrost in good time, depending on
how much fresh food is to be frozen: about 6 hours before
placing the food inside in case of small amounts and about 24
hours in advance in case of the maximum amount of food to be
frozen.
Wrap produce and spread it out as far as possible. Do not
allow produce to be frozen to touch produce that is already
frozen to prevent the latter thawing.
You do not have to activate SuperFrost in the following cases:
when placing frozen food in the freezer
-
when freezing up to approx. 2 kg fresh food daily
-
5.8.1 Freezing with SuperFrost
Briefly press the SuperFrost button
u
The SuperFrost button
w
The freezer temperature drops, the appliance operates with
w
maximum refrigerating performance.
Fig. 2 (5)
Fig. 2 (5)
shines.
once.
6 * Depending on model and options
Page 7
Control
For a smaller quantity of produce to be frozen:
wait approx. 6 h.
u
Place wrapped produce in the deep bottom drawers.
u
For the maximum quantity of produce to be frozen:
wait approx. 24 h.
u
Remove the deep bottom drawers and place produce
u
directly on the bottom shelves.
SuperFrost is automatically deactivated. Depending on the
w
quantity placed inside, after 30 h at the earliest, 65 h at the
latest.
The SuperFrost button
w
is completed.
Place produce in the drawers and push the latter back in
u
again.
The appliance continues to operate in the energy-saving,
w
normal mode.
Fig. 2 (5)
extinguishes once freezing
5.9 Drawers
Note
The energy consumption increases and the cooling performance decreases if there is insufficient ventilation.
For appliances with NoFrost:
Leave the bottom drawer in the appliance!
u
Always keep the air slits of the fan free at the rear wall!
u
5.11 VarioSpace
Apart from being able to remove
the drawers, you can also
remove the shelves, creating
space for large items of frozen
food. Poultry, meat, large pieces
of game and high bakery products can be frozen in one piece
and prepared.
The maximum load for the top drawer is 5 kg and for the
u
other drawers 25 kg each.
The shelves can each be loaded with 35 kg of frozen food.
u
5.12 Pull-out rails
To remove the pull-out rail: press
u
down the front snap-fit devices and
push the pull-out rail away, sideways
and backwards.
Fig. 3
Fig. 4
To store frozen food directly on the shelves: raise the drawer
u
at the back and pull it out forwards.
5.10 Shelves
To remove the shelf: lift up at the
u
front and pull out.
To put the shelf back: simply push
u
in as far as it will go.
To fit the pull-out rail: engage at the
u
back and snap into place at the front.
5.13 Information system
Fig. 5
(1) Ready-made meals, ice
cream
(2) Pork, fish (5) Game, mushrooms
(3) Fruit, vegetables (6) Poultry, beef/veal
The figures indicate the storage time in months for several
types of frozen food in each case. Storage times given are
guide times.
(4) Sausages, bread
5.14 Cold storage accumulators
The cold storage accumulators prevent the temperature from
rising too fast in the event of power failure.
* Depending on model and options 7
Page 8
Maintenance
5.14.1 Using cold storage accumulators
Place the cold storage accu-
u
mulators in the top freezer
compartment to save space.
Place the frozen cold storage
u
accumulators on the frozen
food in the upper front area of
the freezer compartment.
5.15 IceMaker*
The IceMaker is in the fourth drawer from the top. The drawer
is marked "IceMaker".
Make certain that the following conditions are met:
The appliance is level.
-
The appliance is connected.
-
The IceMaker is connected to the water supply.
-
5.15.1 Switching on the IceMaker*
Fig. 6
Pull out the drawer.
u
Press the On/Off button
u
shines.
Push in the drawer.
u
Note
The IceMaker produces ice cubes only if the drawer is fully
u
closed.
5.15.2 Producing ice cubes*
The production capacity depends on the freezer temperature.
The lower the temperature, the more ice cubes can be
produced in a specific period.
The ice cubes drop from the IceMaker into the drawer. When a
certain filling level has been reached, no further ice cubes are
produced. The IceMaker does not fill the drawer right up to the
brim.
If large quantities of ice cubes are needed, the complete
IceMaker drawer can be exchanged for the adjacent drawer.
When the drawer is closed, the IceMaker automatically recommences production.
Once the IceMaker has been switched on for the first time, it
may take up to 24 hours until the first ice cubes are produced.
Fig. 6 (1)
so that the LED
Fig. 6 (2)
6 Maintenance
6.1 Defrosting with NoFrost
The NoFrost system automatically defrosts the appliance.
The moisture condenses on the evaporator, is periodically
defrosted and evaporates.
The appliance does not have to be manually defrosted.
u
6.2 Cleaning the appliance
Risk of injury and damage as a result of hot steam!
Hot steam may damage the surfaces and cause burns.
u
NOTICE
Incorrect cleaning damages the appliance!
u
u
u
u
u
u
u
u
u
u
u
u
u
u
After cleaning:
u
u
u
u
CAUTION
Do not use any steam cleaners!
Do not use cleaning agents in concentrated form.
Do not use any scouring or abrasive sponges or steel wool.
Please do not use any aggressive, scouring, sand-,
chloride-, chemical- or acid-based cleaning agents.
Do not use chemical solvents.
Do not damage or remove the type plate on the inside of the
appliance. It is important for the customer service.
Do not pull off, bend or damage cables or other components.
Do not allow any cleaning water to enter the drain channel,
ventilation grille or electrical parts.
Please use soft cleaning cloths and a universal pH-neutral
cleaning agent.
Please use cleaning and care products suitable for contact
with foodstuffs in the appliance interior.
Empty appliance.
Pull out the power plug.
Clean plastic outer and inner surfaces with lukewarm
water and a little washing-up liquid.
Clean items of equipment by hand with lukewarm water
and a little washing-up liquid.
Only use a damp cloth to clean the telescopic rails. The
grease in the runners is for lubrication purposes and must
not be removed.
Wipe dry the appliance and items of equipment.
Connect the appliance and switch it on again.
Switch on SuperFrost (see 5.8) .
When the temperature is sufficiently cold:
Put the food back inside.
Note
When the appliance is used for the first time and if it has been
out of use for a long time, particles may collect in the IceMaker
and/or water conduit.
Therefore do not use or consume the ice cubes made in the
u
first 24 hours.
6.3 Cleaning the IceMaker*
5.15.3 Switching off the IceMaker*
When the IceMaker is switched off, the IceMaker drawer can
also be used for freezing and storing food.
Press the On/Off button for about 1 second until the LED
u
goes out.
Clean the IceMaker.
u
This ensures that no water or ice remains in the IceMaker.
w
The IceMaker has to be switched on.
Pull out the drawer and remove the ice cubes.
u
Clean the drawer with warm water and mild washing-up
u
liquid.
8 * Depending on model and options
Fig. 7
Page 9
Malfunction
When the drawer is pulled out, hold down the On/Off button
u
(about 10 seconds).
After about 1 s the LED goes out, the IceMaker is switched
w
off.
After about 10 s the LED flashes for about 60 s.
w
Slide in the drawer while the LED is flashing.
u
The ice-cube tray of the IceMaker turns to a skew position.
w
Remove the drawer.
u
Clean the ice cube tray with warm water. If necessary, use
u
mild washing-up liquid. Then rinse.
Switch the IceMaker on again.
Press the ON/OFF button until the LED shines, then slide in
u
the drawer.
The IceMaker starts producing ice cubes.
w
If washing-up liquid was used:
throw away the first three loads of ice cubes to get rid of any
u
remaining washing-up liquid.
6.4 Customer service
First check whether you can correct the fault yourself by reference to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
Risk of injury if repair work is not carried out professionally!
u
u
WARNING
Have any repairs and action - not expressly specified - on
the appliance and mains cable carried out by service
personnel only. (see Maintenance)
Read the appliance
designation
Fig. 8 (1)
No.
Fig. 8 (2)
serial No.
off the type plate
located inside the
appliance on the lefthand side.
, service
and
Fig. 8 (3)
Fig. 8
Notify the customer service, specifying the fault, appliance
u
designation
Fig. 8 (3)
This will help us to provide you with a faster and more accu-
w
rate service.
Keep the appliance closed until the customer service
u
arrives.
The food will stay cool longer.
w
Pull out the mains plug (not by pulling the connecting cable)
u
or switch off the fuse.
Fig. 8 (1)
.
, service No.
Fig. 8 (2)
and serial No.
7 Malfunction
Your appliance is designed and manufactured for a long life
span and reliable operation. If a malfunction nonetheless
occurs during operation, check whether it is due to a handling
error. In this case you will have to be charged for the costs
incurred, even during the warranty period. You may be able to
rectify the following faults yourself:
Appliance does not work.
The appliance is not switched on.
→
Switch on the appliance.
u
The power plug is not properly inserted in the wall socket.
→
Check power plug.
u
The fuse of the wall socket is not in order.
→
Check fuse.
u
The compressor runs for a long time.
The compressor switches to a low speed when little cold is
→
needed. Although the running time is increased as a result,
energy is saved.
This is normal in energy-saving models.
u
SuperFrost is activated.
→
The compressor runs for longer in order to rapidly cool the
u
food. This is normal.
A LED on the bottom rear of the appliance (at the
compressor) flashes regularly every 15 seconds*.
The inverter is equipped with a diagnostic LED.
→
The flashing is normal.
u
Excessive noise.
Speed-controlled* compressors may produce varying
→
running noise due to different speed steps.
The sound is normal.
u
A bubbling and gurgling noise.
This noise comes from the refrigerant flowing in the refriger-
→
ation circuit.
The sound is normal.
u
A quiet clicking noise.
The noise is produced whenever the refrigeration unit
→
(motor) automatically switches on or off.
The sound is normal.
u
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
The refrigeration increases automatically when the Super-
→
Frost, function is activated, fresh food has just been placed
in the appliance or the door has been left open for a while.
The sound is normal.
u
The ambient temperature is too high.
→
Solution: (see 1.2)
u
A low hum.
The sound is produced by air flow noise of the fan.
→
The sound is normal.
u
Flow sound at the soft stop mechanism.
The noise is produced when the door is opened and
→
closed.
The sound is normal.
u
The temperature display indicates: F0 to F5.
There is a fault.
→
Contact the customer service (see Maintenance).
u
The temperature display indicates: nA
The freezer temperature rose too high over the last hours or
→
days due to a power failure or power interruption. When the
power interruption is over, the appliance will continue to
operate in the last temperature setting.
Press alarm button
u
The highest temperature reached during power failure is
w
indicated in the temperature display for approx. 60 seconds.
The electronic unit then indicates the actual current freezing
temperature again.
To prematurely cancel the display of the warmest tempera-
u
ture: press alarm button
Check the quality of the food. Do not consume spoiled food.
u
Do not re-freeze thawed food.
The IceMaker cannot be switched on. *
The appliance and therefore the IceMaker are not
→
connected.
Connect the appliance. (see Putting into operation).
u
The IceMaker does not make any ice cubes.*
The IceMaker is not switched on.
→
Switch on the IceMaker.
u
The drawer of the IceMaker is not properly closed.
→
Close the drawer properly.
u
The water connection is not open.
→
Fig. 2 (6)
Fig. 2 (6)
.
* Depending on model and options 9
Page 10
Decommissioning
Open the water connection.
u
The temperature is not cold enough.
The door of the appliance is not properly closed.
→
Close the door of the appliance.
u
Insufficient ventilation.
→
Clear ventilation grilles.
u
The ambient temperature is too high.
→
Solution: (see 1.2) .
u
The appliance was opened too frequently or for too long.
→
Wait until the appliance reaches the required temperature
u
itself. If not, contact the customer service. (see Maintenance).
Too much fresh food was placed inside without SuperFrost.
→
Solution: (see 5.8)
u
The temperature is incorrectly set.
→
Set the temperature to a colder setting and check after 24
u
hours.
The appliance is too close to a source of heat (stove, heater
→
etc).
Change the position of the appliance or the source of heat.
u
The appliance was not inserted properly into the recess.
→
Check whether the appliance was inserted correctly and
u
the door closes properly.
8 Decommissioning
Pull out the plug.
u
Cut through the connecting cable.
u
8.1 Shut off the water intake*
NOTICE
Malfunction of the water intake!
If the water intake is shut off during operation but the IceMaker
remains in operation, the water intake pipe may ice up.
Switch off the IceMaker if the water supply is interrupted
u
(e.g. holiday).
8.2 Switching off the appliance
Press On/Off button
u
approx. 2 seconds.
The temperature display is dark.
w
If the appliance cannot be switched off, the child
w
lock function is active (see 5.2) .
Fig. 2 (4)
for
8.3 Taking the appliance out of service*
Empty the appliance.
u
Put the IceMaker in the cleaning position (see Mainte-
u
nance).
Pull out the power plug.
u
Clean the appliance (see 6.2) .
u
Leave the door open to prevent odour.
u
9 Disposing of the appliance
The appliance contains some reusable materials
and should be disposed of properly - not simply
with unsorted household refuse. Appliances which
are no longer needed must be disposed of in a
professional and appropriate way, in accordance
with the current local regulations and laws.
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
Disable the appliance.
u
10 * Depending on model and options
Loading...