Liebert 115V, 350-700 VA User Manual

POWERSURE™ PROACTIVE

350-700 VA

115V & 230V

USER MANUAL

English / Deutsch / Français /

Italiano / Español

2

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that should be followed during
the installation and maintenance of the UPS and batteries. Please read this
manual thoroughly before attempting to install or operate this UPS.

WARNING:

§ To prevent the risk of fire or electric shock, install the UPS in a temperature
and humidity controlled room, free of conductive contaminants.

§ Operate the UPS only from a properly grounded/earthed AC supply.

§ To reduce the risk of electric shock, do not remove the cover, as it has no

user-serviceable parts inside. Some components are live, even when AC
power is disconnected. For service, contact a qualified technician.

§ To reduce the risk of fire, use the proper rating when replacing the fuse.

CAUTION:

Although your UPS has been designed and manufactured to assure personal
safety, improper use can result in electrical shock or fire. To insure safety,
please observe the following rules:

§ Turn off and unplug your UPS before cleaning. Do not use liquid or aerosol
cleaners. A dry cloth is recommended to remove dust from the surface of
your UPS.

§ Do not install or operate your UPS in or near water.

§ Do not place UPS on an unstable cart, stand, or table.

§ Do not place UPS under direct sunlight or close to heat emitting sources.

§ To allow proper ventilation of UPS, do not block or cover sides of unit.

§ Do not place UPS power cord in any area where it may get damaged by

heavy objects.

§ Follow all warnings and instructions marked on the UPS. Do not attempt to
service the UPS, as it has no user-serviceable parts inside. Refer all repairs
to qualified service personnel.

ATTENTION:

Turn off and unplug your UPS from the outlet and contact qualified service
personnel if:

§ The power cord or plug is damaged.

§ Liquid has been spilled on the UPS.

§ The fuse blows frequently.

§ The UPS does not operate even when user follows the operating

instructions.

CONDITIONS OF USE: The input receptacle must be within 6 feet (1.8 meters)
of the UPS.

Your UPS provides conditioned power to connected equipment. Maximum load
must not exceed that shown on UPS rating label. If uncertain, consult your
distributor or Liebert.

Placing magnetic storage media on top of the UPS may result in data corruption.
This equipment can be operated by individuals without previous training.

3

GENERAL INSTALLATION

R

Plug in loads

Press On button

R

32 - 104 F

0 - 40 C

Remove from box

Check for damage

Or

4 inches
110 mm

Plug UPS into AC / Mains

4

INTRODUCTION & SYSTEM DESCRIPTION

Congratulations on your choice of the Liebert PowerSure ProActive
Uninterruptible Power System (UPS). It provides conditioned power to
microcomputers and other sensitive electronic equipment.

The PowerSure ProActive is a compact, “Automatic Voltage Regulation” UPS. It
offers “line-interactive” features by continuously conditioning and regulating
output voltage, whether the utility power is present or not. It supplies connected
equipment with stepped approximation to sinewave power to simulate the power
generated by the utility.

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses, generates and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference with radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that which

the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

BATTERY OPERATION

Battery mode occurs in event of extreme input conditions or complete utility
failure. During battery mode the Utility LED will flash every second and an alarm
will sound every 3 seconds. This will change to a beep every second when
battery runs low (approximately 2 minutes remaining).

WARNING: Turning off the UPS while in battery mode will result in loss of output
power.

Press Battery Test button occasionally to ensure battery is fully charged.

AUDIBLE ALARM CONDITIONS

CONDITION ALARM

Battery mode
(utility failure)

Low battery One beep every second; less than two

Battery replacement Two second beep every minute

UPS output overload Continuous tone

UPS fault Continuous tone

One short beep every three seconds; more
than two minutes of run time remaining

minutes of run time remaining