LG Innotek RNTDST01A User Manual

Home Security Camera

REGULATION INFORMATION TO THE USER (FCC)

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:
(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including
interference that may cause undesired operation.

Caution: Any changes or modifications to the equipment not expressly

approved by the party responsible for compliance could void user’s

authority to operate the equipment.
This appliance and its antenna must not be co-located or operation in

conjunction with any other antenna or transmitter.
A minimum separation distance of 20 ㎝ must be maintained between

the antenna and the person for this appliance to satisfy the RF
exposure requirements.

REGULATION INFORMATION TO THE USER (IC)

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and your body.

Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm

de distance entre la source de rayonnement et votre corps

1. Product & Accessories

IP Network Camera, Adapter, Ethernet to Micro USB Cable

Anchor & Screw

Quick Manual Non-slip pad

2. Operating Condition

- IP Network Camera : 32℉~104℉

3. Wall mount Installation

1. Tighten two screws to fix the bracket on the wall using screw driver.

2.Push and lock stand body to the bracket .

4. Table-top installation

LED

Status

Description

Camera Power LED
Blinking Green

Firmware updating
Pulsing Amber

Connecting to Server
Pulsing Green
Booting

Solid Amber

No Connectivity to Server

Solid Green
Working

Solid Red

Malfunction
Off

Power Off

Camera Network LED
Pulsing Green

Connecting to Router
Pulsing Red

No Connectivity to Router

Solid Green

Network Working

Solid Red

Network Working with weak
signal (RSSI < -80)

Off

Network Disabled

Camera Video LED

Solid Green
Recording

Off

Camera not Working

1. Attach the non-slip pad under mount bracket and lock the
camera body.

2. Adjust thecamera view direction

7. LED Descriptioin

Camera Video Led

Camera Power Led

Camera Network Led

5. Pairing the Device

1. Plug in the camera.

2. Connect ethernet cable to controller ethernet port.

3. Please follow instructions on their controller.

6. Mount SD Card(Optional)

1. Insert a micro SD memory(be careful memory up/down side)

8. Factory Reset

Press and hold ‘Reset’ button more than 10 seconds until blink red of

Network LED

Reset

Reset Button 표현 그림 필요

9. Caution

1) This camera is an indoor good.(Don’t install outdoor)

2) Don’t cover vent hole

3) Don’t drop water or chemical substance.

4) Strong light is a cause of some image quality problem.

(sun light, headlight form automobiles, etc.)