Please return 1 copy for your confirmation with
your signature and comments.
Ver. 0.0Apr. 20, 2009
PREPARED BY
B. T. Jang / Engineer
K. H. Lee / Engineer
Products Engineering Dept.
LG Display Co., Ltd
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1/ 30
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LP156WH2
Liquid Crystal Display
Product Specification
Contents
No
1
2
3
4
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
ELECTRICAL CHARACTREISTICS
3-1
INTERFACE CONNECTIONS
3-2
LVDS SIGNAL TIMING SPECIFICATION
3-3
SIGNAL TIMING SPECIFICATIONS
3-3
SIGNAL TIMING WAVEFORMS
3-4
COLOR INPUT DATA REFERNECE
3-5
POWER SEQUENCE
3-6
OPTICAL SFECIFICATIONS
ITEM
Page
1
2
3
4
5
6
7
8-9
10
10
11
12
13-15
5
Ver. 0.0Apr. 20, 2009
MECHANICAL CHARACTERISTICS
APPENDIX. LPL PROPOSAL FOR SYSTEM COVER DESIGNA
RELIABLITY6
INTERNATIONAL STANDARDS7
SAFETY7-1
EMC7-2
PACKING8
DESIGNATION OF LOT MARK8-1
PACKING FORM8-2
PRECAUTIONS9
APPENDIX. Enhanced Extended Display Identification Data A
16-19
20-22
23
24
24
25
25
26-27
28-30
2/ 30
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LP156WH2
Liquid Crystal Display
Product Specification
RECORD OF REVISIONS
DescriptionPageRevision DateRevision No
First Draft (Preliminary Specification)-Apr. 20, 20080.0
EDID
ver
0.0
Ver. 0.0Apr. 20, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3/ 30
www.panelook.com
Global LCD Panel Exchange Center
1. General Description
The LP156WH2 is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive
type display operating in the normally white mode. This TFT-LCD has 15.6 inches diagonally measured
active display area with HD resolution(768 vertical by 1366 horizontal pixel array). Each pixel is divided into
Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness
of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of
more than 262,144 colors.
The LP156WH2 has been designed to apply the interface method that enables low power, high speed, low
EMI.
The LP156WH2 is intended to support applications where thin thickness, low power are critical factors and
graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the
LP156WH2 characteristics provide an excellent flat display for office automation products such as Notebook
PC.
Hard Coating(3H), Glare treatment of the front polarizerSurface Treatment
YesRoHS Comply
2
(Typ.5 point)Luminance, White
ڌڎڑڑ
Ver. 0.0Apr. 20, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/ 30
www.panelook.com
Global LCD Panel Exchange Center
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
www.panelook.com
LP156WH2
Liquid Crystal Display
Product Specification
Table 1. ABSOLUTE MAXIMUM RATINGS
ParameterNotes
Symbol
Values
Units
MaxMin
Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
OP
Storage Humidity
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39
Wet Bulb
20
]
30
Temperature [
10
0
qC Max, and no condensation of water.
90% 80%
60
50
40
60%
Humidity[(%)RH]
40%
20%
10%
Storage
Operation
at 25 r 5qCVdc4.0-0.3VCC
1qC500TOP
1qC60-20HST
1%RH9010H
1%RH9010HST
-20
10
20304050
6070800
Dry Bulb Temperature []
Ver. 0.0Apr. 20, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5/ 30
www.panelook.com
Global LCD Panel Exchange Center
3. Electrical Specifications
3-1. Electrical Characteristics
The LP156WH2 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED BL.with LED Driver.
ParameterSymbol
LOGIC :
BACKLIGHT : ( with LED Driver)
PWM High Level Voltage
PWM Low Level Voltage
LED_EN High Voltage
LED_EN Low Voltage
Note)
1. The specified Icc current and power consumption are under the Vcc = 3.3V , 25, fv = 60Hz condition
whereas Mosaic pattern is displayed and fv is the frame frequency.
www.panelook.com
Product Specification
Table 2. ELECTRICAL CHARACTERISTICS
Values
CCPower Supply Input Voltage
CCPower Supply Input Current
I
CCPower Consumption
CC_PPower Supply Inrush Current
LEDLED Power Input Voltage
LEDLED Power Input Current
LEDLED Power Consumption
LED_PLED Power Inrush Current
PWMPWM Impedance
PWMPWM Frequency
PWM_ H
PWM_ L
LED_EN_H
LED_EN_L
Liquid Crystal Display
MaxTypMin
V3.63.33.0V
mA1500--I
11010090ZLVDSLVDS Impedance
ȳ
V20.012.07.0V
mA---I
kȳ604020Z
V5.3-3.0V
V0.5-0V
V5.3-3.0V
V0.5-0V
LP156WH2
NotesUnit
1mA445385-
1W1.51.3-P
2
3mA-290-I
3W3.93.5-P
4%100-12.5-PWM Dimming (Duty) Ratio
5Hz10000-200F
6Hrs--12,000Life Time
2. This impedance value is needed to proper display and measured form
LVDS Tx to the mating connector.
3. The specified LED current and power consumption are under the Vled = 12.0V , 25, Dimming of Max
luminance whereas White pattern is displayed and fv is the frame frequency.
4. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
5. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
6. The life time is determined as the time at which brightness of LCD is 50% compare to that of initial value
at the typical LED current. These LED backlight has 6 strings on it and the typical current of LED’s string
is base on 19mA.
Ver. 0.0Apr. 20, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6/ 30
www.panelook.com
Global LCD Panel Exchange Center
3-2. Interface Connections
This LCD employs one interface connections, a 40 pin connector is used for the module electronics interface
and LED Driver.
The electronics interface connector is a model 20455-040E-0x manufactured by I-PEX.