LG WM3499HVA User Manual

OWNER’S MANUAL

WASHING MACHINE

ENGLISH

FRANÇAIS

Please read this owner’s manual thoroughly before operating and keep it handy for reference at all times.

WM3499H*A

MFL70561489

www.lg.com

TABLE OF CONTENTS

3 PRODUCT FEATURES

4 IMPORTANT SAFETY INSTRUCTIONS

4 BASIC SAFETY PRECAUTIONS 5 GROUNDING INSTRUCTIONS 6 SAFETY INSTRUCTIONS FOR INSTALLATION 7 SAFETY INSTRUCTIONS FOR USE, CARE,

CLEANING, AND DISPOSAL

8 PRODUCT OVERVIEW

8 Parts 8 Accessories 9 Control Panel Features

11 INSTALLATION

11 Installation Overview 12 Choosing the Proper Location 13 Unpacking and Removing Shipping Bolts 14 Connecting the Water Lines 15 Connecting the Drain Line 16 Leveling the Washer 17 Connecting to the Power Supply 17 Testing the Washer

18 PREPARATION

18 Sorting Wash Loads 19 - Fabric Care Labels 19 - Sorting Laundry 20 Using Detergent/Fabric Softener 20 - Recommended Detergent 20 - Loading the Dispenser

22 OPERATION

22 Using the Washer 23 Cycle Guide 24 Wash Cycles 24 - Sanitary: Reducing Laundry Bacteria 24 - Baby Wear: Lightly Soiled Baby Clothes 24 - Bulky/Large: Blankets or Bulky Items 24 - Heavy Duty: Heavily Soiled Items 24 - Perm. Press: Wrinkle-Free Items 24 - Normal: Normal Items 24 - AllergieneTM: Help Prevent Allergens 24 - Hand Wash/Wool: Items Labeled Wool or

Hand-Wash

24 - Delicates: Sheer Items 24 - Quick Wash: Washing Quickly

24 - Wash+Dry: A Small Load which Can Be

Tumble Dried

24 - Drain+Spin: Drain and Spin Only 25 Cycle Modifier Buttons 25 Setting Options Before Cycle 25 - Temp. 25 - Spin 26 - Dry 27 - Delay Wash 27 - Steam 27 - Wi-Fi 27 - Pre-wash 27 - Signal On/Off 28 Setting Options During Cycle 28 - Control Lock 28 - EcoHybrid 28 - Heavy Soil 28 Add Garments

29 MAINTENANCE

29 Regular Cleaning 29 - Care After Wash 29 - Care in Cold Climates 30 Cleaning 30 - Tub Clean 31 - Cleaning the Detergent Dispenser Drawer 32 - Cleaning the Water Inlet Filters 33 - Cleaning the Drain Pump Filter 34 - Cleaning the Door Seal

35 TROUBLESHOOTING

35 Checking Error Messages 36 Before Calling for Service

39 SPECIFICATIONS

40 SMART FUNCTIONS

40 Using Smart Diagnosis™ 40 Using LG SmartThinQ Application

43 WARRANTY

Rev.00_180609

PRODUCT FEATURES

INVERTER DIRECT-DRIVE MOTOR

The inverter direct drive motor, which is directly connected to the drum, is capable of producing multiple

distinct motions for optimal wash performance with very little noise and vibration. The motor assembly also contains fewer moving parts, resulting in fewer repairs.

SMART DIAGNOSIS™

Should you experience any technical difficulty with your washing machine, it has the capability of

transmitting diagnostic data to your smart phone via a free app or directly to the Customer Information Center for quick and efficient troubleshooting (refer to page 40).

TUB CLEAN

Regular cleaning of the tub on a monthly basis using TUB CLEAN can help keep the tub clean and fresh.

LARGE CAPACITY STAINLESS STEEL DRUM

The large capacity stainless steel drum offers extreme durability and is tilted to improve efficiency and

allow easier access for large items.

CONTROL LOCK

Use this option to disable the controls during a wash cycle. This option can prevent children from

changing cycles or operating the machine.

DETERGENT DISPENSER DRAWER

The four-compartment dispenser drawer makes it easy to separate the pre-wash detergent, the main

laundry detergent, liquid bleach, and fabric softener into different compartments that will be dispensed automatically at the appropriate time.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.

These words mean:

DANGER

You will be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

BASIC SAFETY PRECAUTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following :

• Use this appliance only for its intended purpose as described in this owner’s manual.

• Before use, the washer must be properly installed as

described in this manual.

• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite

or explode.

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any

accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children.

• Before the washer is removed from service or discarded, remove the lid to prevent children from climbing inside.

• Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

• Do not tamper with controls.

• Keep the area underneath and around your

appliances free of combustible materials (lint, paper, rags, etc.), gasoline, chemicals and other flammable vapors and liquids.

• Do not repair or replace any part of the washer or

attempt any servicing other than as described in this manual. We strongly recommend that any service be

performed by a qualified technician.

• See Installation Instructions for grounding

requirements.

• ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

• Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

• Use fabric softeners or products to eliminate static

only as recommended by the manufacturer.

• This washer is not designed for maritime use or for mobile installations such as in RVs, aircraft, etc.

• Turn off the water faucets and unplug the washer if the

machine is to be left for an extended period of time, such as during vacations.

• Packaging material can be dangerous for children. There is a risk of suffocation! Keep all packaging from

children.

• Always check the inside of the washer for foreign objects before loading laundry. Keep the lid closed when not in use.

• Do not reach into the appliance if the tub or agitator is moving.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

ENGLISH

WARNING

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with a qualified electrician or servicer if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or death.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following :

• Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions are packed with the washer for the installer’s reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service technician. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

For personal safety, this appliance must be properly grounded. Failure to follow this warning can

cause serious injury, fire, electric shock, or death.

• The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock from this appliance.

• This washer must be plugged into a 120 VAC, 60 Hz grounded outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is properly grounded. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow

this warning can cause serious injury, fire, electric shock, or death.

• Do not install on carpet. Install washer on a solid floor. Failure to follow this warning can cause serious leak damage.

•

Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow these warnings can cause

serious injury, fire, electric shock, or death.

• The washer should always be plugged into its own

individual electrical outlet which has a voltage

rating that matches the rating plate. This provides

the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

• Never unplug your washer by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Repair or immediately replace all power cords

that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. Failure

to follow this warning can cause serious injury, fire, electric shock, or death.

• When installing or moving the washer, be careful not to pinch, crush, or damage the power cord. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• The washer must be installed and electrically

grounded by a qualified service person in accordance with local codes to prevent shock

hazard and assure stability during operation.

• The washer is heavy. Two or more people may be needed to install and move the appliance. Failure to do so can result in back or other injury.

•

Store and install the washer where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to follow this

warning can cause serious leak damage.

• To reduce the risk of electric shock, do not install the washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• To reduce the risk of injury to persons, adhere to

all industry recommended safety procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety

warnings in this manual could result in property damage, injury to persons or death.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following :

• Unplug the washer before cleaning to avoid the

risk of electric shock.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the finish.

• Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that could ignite the materials.

• Do not wash items that are soiled with vegetable or cooking oil. These items may contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

• Disconnect this appliance from the power supply

before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Do not combine laundry products for use in one

load unless specified on the label.

• Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using laundry products. Incorrect usage can

produce poisonous gas, resulting in serious injury or death.

• Do not reach into the washer while parts are

moving. Before loading, unloading, or adding items, press the START/PAUSE button and allow the drum to coast to a complete stop before reaching inside. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

• Do not allow children to play on or in the washer.

Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with these

warnings could result in serious injury to persons or death.

• Destroy the carton, plastic bag, and other packing

materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers. Failure to comply with these

warnings could result in serious injury to persons or death.

• Keep laundry products out of children’s reach. To

prevent injury to persons, observe all warnings on product labels. Failure to comply with these

warnings could result in serious injury to persons or death..

• Before your washer is removed from service or

discarded, remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside Failure to do

so can result in serious injury to persons or death.

• Make sure the dispenser drawer is closed at all times when not being filled with laundry products. Failure to keep the drawer closed can result in personal injury or flooding.

• Certain internal parts are intentionally not

grounded and may present a risk of electric shock only during servicing. Service personnel - Do not

contact the following parts while the appliance is energized: pump, valve, motor, control board, drying heater.

ENGLISH

SAVE THESE INSTRUCTIONS

PRODUCT OVERVIEW

Parts

Detergent

dispenser

drawer

(See page 20)

Door

Leveling feet

Drain pump filter cover

Accessories

Drain hose

Drain pump filter

Water inlets

Control panel (See page 9)

Inverter directdrive motor

Large-capacity stainless steel drum

Shipping

bolts

Power cord

Drain hose

Included Accessories

Hot/cold water hoses Non-skid pads

Wrench Tie strap(optional)

Caps for covering

shipping bolt holes

Elbow bracket

(for securing drain hose)

NOTE

yContact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are

missing.

yFor your safety and for extended product life, use only authorized components. The manufacturer

is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized components or parts.

yThe images in this guide may be different from the actual components and accessories, which are

subject to change by the manufacturer without prior notice for product improvement purposes.

PRODUCT OVERVIEW

Control Panel Features

Cycle selector

Power Button

Operation

Button Description

yTurns the washing machine on and off. y(During the wash cycle) stops operation, and cancels the settings.

Tub Clean

- For tub clean (see page 30).

Sanitary

- For underwear, diapers, etc. (see page 24).

Baby Wear

- For lightly soiled baby clothes (see page 24).

Bulky/Large

- For blankets or large, bulky items (see page 24).

Heavy Duty

- For heavily soiled cotton fabric (see page 24).

Perm. Press

- For wrinkle-free fabric (see page 24).

Normal

- For general laundry, such as cotton T-shirts or towels (see page 24).

Qiuck Wash

- Provides fast washing time for small loads and lightly soiled clothes. (see page 24).

Hand Wash/Wool

- For wool or hand-wash fabrics (see page 24).

Delicates

- For sheer and delicate fabrics (see page 24).

Allergiene

- For cotton, underwear,pillow covers, bed sheets, baby wear (see page 24).

Wash+Dry

- For a small load which can be washed and dried in the same cycle (see page 24).

Drain+Spin

- For items that only require draining and spinning (see page 24).

yStarts or pauses the wash cycle.

- If you do not press the Start/Pause button within 4 minutes of selecting a cycle, the

y(Press repeatedly) Selects the water temperature for the wash cycle (see page 25).

- Select water temperature from 5 settings.

y(Press repeatedly) Selects the spin speed (see page 25).

- Selects spin speed from 5 settings.

y(Press repeatedly) Selects a dry cycle. Pressing this button enables drying.

(See page 26).

Water

Operation Dry Button

Start/ Pause Button

washing machine will turn off automatically and all settings will be lost.

Steam Selection Button

Display

Pre-wash Button

Temperature Selection Button

Delay Wash Button

Spin Button

Add Garments Button

ENGLISH

PRODUCT OVERVIEW

Operation (continued)

Button Description

Display

Display Icon Description

ySet the delay time of starting the cycle (see page 27).

yUse this option for enhanced washing performance with low energy

consumption.

yUse this option to add garments or remove foreign objects like coins

or keys after the cycle has started (see page 28).

y(Press before wash cycle) Pre-wash heavily soiled laundry (see page 27). y(Press and hold during wash cycle) Lock/Unlock the buttons (see page 28).

Cycle process indicator

Estimated time remaining/ error message display (See page 35)

yThis portion of the display shows which stage of the wash cycle is

currently under way (Wash, Spin, Dry).

yThis indicator shows that the door is locked. The washer door will lock while

the washer is operating. The door can be unlocked by pressing the Start/ Pause button to stop the washer.

yWhen the Start/Pause button is pressed, the washer automatically detects

the wash load (weight) and optimizes the washing time, based on the selected cycle and options. The display will then indicate the estimated time remaining for the selected wash cycle.

INSTALLATION

Installation Overview

Choosing the proper

location

Connecting

the drain line

Testing the washer

Unpacking and removing

shipping bolts

Leveling the washer

Connecting

the water line

Connecting to the

power supply

ENGLISH

WARNING

yWasher is heavy! Two or more people are required when moving and unpacking the washer.

to follow this warning can result in back or other injury.

yStore and install the washer where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions.

shock, or death.

yProperly ground washer to conform with all governing codes and ordinances.

warning can cause serious injury, fire, electric shock, or death.

yTo reduce the risk of electric shock, do not install the washer in humid spaces.

warning can cause serious injury, fire, electric shock, or death.

yThe base opening must not be obstructed by carpeting when the washer is installed on a carpeted

floor.

yDo not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

outlet.

yCertain internal parts are intentionally not grounded and may present a risk of electric shock only

during servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump, valve, motor, control board.

Failure to follow this warning can cause serious injury, fire, electric

Failure to follow this

Failure

INSTALLATION

Choosing the Proper Location

Install the washing machine on a solid floor that is strong and rigid enough to support the weight of the washing machine, even when fully loaded, without flexing or bouncing. If the floor has too much flex, you may need to reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise.

Clean the floor before installation.

- Make sure to select solid and smooth ground.

Two or more people are needed for moving and

unpacking the washing machine.

Allow for sufficient space between the walls and

the washing machine for installation.

Space Requirements

You must allow sufficient space for water lines, the drain line, and airflow.

NOTE

yBe sure to allow for wall, door, or floor

moldings that may incr he required clearances.

Clearances

45" (114.9 cm)

25.4" (64.5 cm)

0.2" (0.5 cm)

NOTE

yThe floor must be strong and rigid enough to

support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

yBefore installing the washer, make sure the

floor is clean, dry and free of dust, dirt, water and oils so the washer feet can not slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise due to poor contact with the floor.

yIf a drip pan must be used, take extra care

to follow the instructions provided with the drip pan and make sure the leveling feet are adjusted for firm and even contact with the pan. Use of drip pans and failure to properly level the machine may result in increased vibration and noise during operation.

33.5" (85.09 cm)

1.6" (4.1 cm)

21.8" (55.39 cm)

24" (60.96 cm) 1" (2.5 cm)1" (2.5 cm)

Unpacking and Removing Shipping Bolts

Remove the washer from the carton base.

If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. Do not lay the washer on its front or back.

Carton Base

INSTALLATION

Starting with the bottom two shipping bolts,

use the wrench (included) to fully loosen all four shipping bolts by turning them counterclockwise. Remove the bolt assemblies by wiggling them slightly while pulling them out.

Locate the four hole caps included in the

accessory pack and install them in the shipping bolt holes.

Cap

ENGLISH

NOTE

ySave the bolt assemblies for future use. To

prevent damage to internal components, do not transport the washer without reinstalling the shipping bolts.

y Failure to remove shipping bolts and retainers

may cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

INSTALLATION

Connecting the Water Lines

Check the rubber seals on both sides of the hose.

- Insert a rubber seal into the threaded fittings on each hose to prevent leaking.

Rubber seal

Connect the hoses to the water inlets tightly by

hand and then tighten another 2/3 turn with pliers.

- Connect the blue hose to the cold water inlet and the red hose to the hot water inlet.

Hot

water

inlet

Cold water inlet

Water hose (To faucet)

Water hose (To water inlet on the washing machine)

Connect the water supply hoses to the HOT and

COLD water faucets tightly by hand and then tighten another 2/3 turn with pliers.

- Connect the blue hose to a cold water faucet and the red hose to a hot water faucet.

WARNING

yDo not overtighten. Damage to the coupling

can result.

After connecting the inlet hoses to the water

faucets, turn on the water faucets to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let the water drain into a bucket, and check the water temperature.

WARNING

yDo not overtighten the hoses.

can damage the valves resulting in leaking and property damage.

Check for leaks by turning on the faucets.

- If water leaks, check steps 1 to 4 again.

NOTE

yFor your safety, and for extended product

life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased, unauthorized parts.

yUse new hoses when installing the washing

machine. Do not reuse old hoses.

yContact LG Customer Service for Assistance

in buying hoses : 1-800-243-0000.

yPeriodically check the hoses for cracks,

leaks and wear, and replace the hoses every 5 years. Do not stretch the water hoses intentionally, and make sure that they are not crushed by other objects.

yWater supply pressure must be between 20

psi and 120 psi (138 – 827 kPA). If the Water supply pressure is more than 120 psi, a pressure reducing valve must be installed.

yTo provide optimum washing performance

the hot water temperature should be set at 120 – 135°F (48-57°C) and the cold at 60°F (15°C).

Overtightening

INSTALLATION

Connecting the Drain Line

Secure the drain hose in place to prevent moving and leaking.

NOTE

The drain hose should be properly secured. Failure to properly secure the drain hose can result in flooding and malfunction.

Total height of the hose end should not exceed 96 inches (244.8 cm) from the bottom of the washer.

The drain must be installed in accordance with any applicable local codes and regulations.

Make sure that the water lines are not stretched, pinched, crushed, or kinked.

Using a Standpipe

Clip the end of the hose into the elbow bracket.

- Connect the elbow bracket within 4 inches (10 cm) of the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.

No more than 4 inches (10 cm)

Using a Laundry Tub

Clip the end of the hose into the elbow bracket.

No more than 4 inches (10 cm)

Elbow bracket

Hang the end of the drain hose over the side of

the laundry tub.

Elbow Bracket

Drain Hose

Use a tie strap to secure the drain hose in place.

ENGLISH

Elbow bracket

Insert the end of the drain hose into the

standpipe.

Elbow Bracket

Drain Hose

Use a tie strap to secure the drain hose in place.

INSTALLATION

Leveling the Washer

The drum of your new washing machine spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be perfectly level and solid.

Check that the washing machine is level.

- Ensure it is level by rocking the top edges of the washing machine or placing a level on the washing machine. The slope beneath the washing machine must not exceed 1°, and all four leveling feet must rest firmly on the floor.

Turn the lower leveling feet clockwise to level

the washing machine.

- Turning the lower leveling feet clockwise raises the washing machine.

Raise Lower

Turn the locknuts counterclockwise and tighten

them when the washing machine is level.

Level

Tighten all 4 lock

nuts securely using

the wrench.

1°

Check again to make sure the machine is level.

- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock.

If the washing machine rocks, repeat steps 1 to 3.

WARNING

yUsing the washing machine without leveling,

it may result in malfunction caused by the production of excess vibration and noise.

yIf you are installing the washing machine

on the optional pedestal, you must adjust the leveling feet on the pedestal to level the washing machine. The washing machine´s leveling feet should be minimized and the locknuts turned counterclockwise to secure them.

yUse the leveling feet only when you level the

washing machine. If you raise the leveling feet unnecessarily, it may cause abnormal vibration of the washing machine.

Using Non-Skid Pads (Optional)

If you install the washing machine on a slippery surface, it may move because of excessive vibration. Incorrect leveling may cause malfunction through noise and vibration. If this occurs, lay the non-skid pads under the leveling feet and adjust the level.

Clean the floor to attach the non-skid pads.

- Use a dry rag to remove and clean foreign objects or moisture. If moisture remains, the non-skid pads may slip.

Adjust the level after placing the washing

machine in the installation area.

Place the adhesive side of the non-skid pad on

the floor.

- It is most effective to install the non-skid pads under the front legs. If it is hard to place the pads under the front legs, place them under the back legs.

This side up

Adhesive side

Remove backing

Check the washing machine’s level again.

- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock. If the washing machine rocks, level the washing machine again.

+ 36 hidden pages