<![endif]>INDONESIAN ENGLISH
OWNER’S MANUAL
WASHING MACHINE
Please read this manual carefully before operating your washing machine and retain it for future reference.
WF-S16D6
P/No.: MFL67221304
Product Features
Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spincycles, the operation stops for safety.
Please close the door gently. Closing the door in an agressive manner can cause damage and or injury.
sensors
The sensor automatically detects the quantity of Detergent put in by a user and the temperature and quality of the water to produce the best algorithm for washing and rinsing, to give the best washing results.
SMART CLEANING
The purpose of this cycle is to optimize detergent residues during the washing and rising cycles, in order to implement this effect,the washer adds more rinsing times by I-sensor. Rinse can be added until max 5 times.
FUZZY logic control
A built-in load sensor automatically detects and measures the laundry load and a microprocessor optimizes washing conditions such as ideal water consumption and washing time.
Advanced technology is built into the Electronic Control System which ensures the best washing result.
START |
SENSING |
SETTING |
WASHING |
AUTO |
Laundry Sensor |
Optimum |
POWER |
||
|
Water Level Sensor |
Washing |
|
OFF |
|
|
Condition |
|
Turbo Drum DD washing
Stains are removed by |
Stains are removed by |
With high speed |
pulsator movement |
the tub movement |
spinning of the tub, |
|
|
stains are removed |
Low Noise Direct Drive System
The advanced Brushless DC motor rotates the Tub directly without belt and clutch, thereby reducing the noise of the washer.
The washing machine adjusts to optimum speed according to the type of clothing in the load.
2
Contents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.
Introduction
Before Starting to Wash
Washing Programs
Additional Function
Program
Installation
Care and Maintenance
Troubleshooting
Terms of Warranty
Specification
Safety Information |
4 |
Identification of Parts |
7 |
Function Information |
8 |
Preparation Before Washing |
9 |
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener |
10 |
Special Guide for Stain Removal |
13 |
Function of each Button |
14 |
FUZZY Wash (Normal Wash) |
16 |
WOOL Wash |
16 |
QUICK WASH |
16 |
JEANS Wash |
16 |
SMART CLEANING |
16 |
SOAK Wash |
18 |
FAVORITE Wash |
19 |
SILENT Wash |
20 |
TUB CLEAN |
21 |
AIR DRY |
22 |
TUB DRY |
22 |
Option Washing |
23 |
DELAY START (RESERVATION) Wash |
24 |
Other Useful Functions |
25 |
Placing and Leveling |
26 |
Connecting Water Supply Hose |
27 |
Connecting Drain Hose |
30 |
Grounding Method |
31 |
Cleaning and Maintenance |
32 |
Use of Handle Locker |
34 |
Common washing problems |
35 |
Troubleshooting |
36 |
Terms of Warranty |
37 |
Specification |
38 |
<![endif]>ENGLISH
3
Safety Information
Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
:This is a warning sign specifying user’s applications which might be dangerous.
:This is a sign specifying ‘Strictly Forbidden’ applications.
Warning : Failure to comply with the instructions under this sign may result in major physical injuries or death.
Caution : Failure to comply with the instructions under this sign may result in minor physical injuries or damages to the product.
WATER |
Warning |
|
HEATER |
||
|
||
SAFETY |
|
•Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER |
Caution |
|
INSTALLATION |
||
|
•The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
•Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.
•Properly ground washer to conform with all governing codes and ordinances. Follow details in Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.
•Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.
•Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
4
Safety Information
YOUR |
Warning |
|
LAUNDRY |
||
|
||
AREA |
• Keep the area underneath and around your appliances free of combustible |
|
|
materials such as lint, paper, rags, chemical, etc. |
Operating with such materials around the machine may trigger explosion or fire.
•The appliance is not intended for use by young children or infirm persons without supervision.
•Young Children should be supervised to ensure that they do not play with appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
WHEN USING |
Caution |
|
THE WASHER |
||
|
•appliance only for its intended purpose as described in this Owner’s Manual.
•process can reduce the flame retardancy of fabrics. To avoid such a result, follow the garment manufacturer’s wash and care instructions.
•the possibility of electric shock, unplug this appliance from the power disconnect the washer at the household distribution panel by removing the
switching off the circuit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Circuit button to turn off does NOT disconnect the appliance from the power supply.
•Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
•If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause leakage of water.
<![endif]>ENGLISH
5
Safety Information
WHEN USING |
Warning |
|
THE WASHER |
||
|
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
|
It may ignite or explode. |
|
WHEN NOT |
Caution |
|
IN USE |
||
|
•Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.
•When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.
•Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
•Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.
It will cause short circuit and electric shock.
6
Identification of Parts
Body
DETERGENT BOX |
FUNCTION
SELECTOR
TUB
START/PAUSE
BUTTON
Use to start or stop the washing machine temporarily.
ADJUSTABLE LEGS
Use to level the washing machine for correct balance & spin operation.
WATER SUPPLY HOSE
Make sure the water does not leak.
POWER PLUG
If the supply cord is
damaged, it must be9
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to avoid a hazard.
Multi Clean Filter
DRAIN HOSE for pump model
Check if the drain hose is hung up before operating the washing machine.
DRAIN HOSE
for non pump model
BASE
Accessories
Drain hose |
Anti-rat cover (option) |
or
NOTE
“ ” Part can be different according to the model.
<![endif]>ENGLISH
7
Function Information
Our machine provides various washing methods which suits various conditions and types of laundry.
Different types of laundry washing
FUZZY(Normal) Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)
Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)
SMART CLEANING
Use this program to get better rising performance. (refer to page 16)
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
•Before washing your woolens check the care label for the washing instructions.
•When washing woolens use a mild Detergent recommended for washing wool.
•Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
•To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.
FAVORITE Wash
This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)
SILENT Wash
Use this program to wash quietly at night. (refer to page 20)
Washing according to the condition of laundry
QUICK WASH
QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)
SOAK Wash
SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 18)
Other washing method
TUB CLEAN
Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 21)
time of the operation.
user accordingly. (refer to page 24)
RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
8
Preparation Before Washing
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light) |
Separate clothes according to the type and amount of soil. |
• COLOR (Whites, Lights, Darks) |
Separate white fabrics from colored fabrics. |
• LINT (Lint producers, Collectors) |
Separate lint producers and lint collectors. |
Lint Producers |
Terry cloth, Chenille, Towels, Nappies, Diapers |
Lint Collectors |
Synthetics, Corduroy, Permanent Press, Socks |
Check before Loading
• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches, |
|
pens, coins, and keys can damage both your washer and your clothes. |
|
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing. |
|
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes. |
|
• Pretreat any dirt and stains. |
|
• Make sure the clothes are washable in water. |
WIRE |
•Check the washing instructions.
•Remove tissue in pockets.
Pretreatment on stains or heavy soil
product or liquid Detergent when placing them in the washer.
,liquid Detergent or a paste of water and granular Detergent. they are left the harder they are to remove.
Loading
(waxes, cleaning fluids, etc.). |
WARNING |
|
|
Fire Hazard |
|
. Adjust the load size |
Never place items in the washer that are |
|
dampened with gasoline or other flammable |
||
the top row of holes in the |
||
fluids. |
||
, press Start button and |
No washer can completely remove oil. |
|
Start button again to restart. |
Do not dry anything that has ever had any type |
|
of oil on it (including cooking oils). |
||
|
||
Light and Large-sized clothing |
Doing so can result in death, explosion, or fire. |
|
|
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
<![endif]>ENGLISH
9
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Using Water
Amount of WATER LEVEL
laundry automatically, then sets the of Detergent.
WATER LEVEL will be shown on the
of water.
automatically detected, it may differ depending the same WATER LEVEL is indicated
NOTE
[ Minimum water amount ]
It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. That’s because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.
Water Temperature (for 2 valve model)
• The machine sets the appropriate temperature automatically according to the wash program .
of all laundry additives and therefore, the cleaning results.
diapers, underclothing and heavily soiled, colorfast items.
colors with light soil.
be needed:
in WARM water
additives and may cause lint, residue, poor cleaning, etc. COLD water as 26~29°C…(80-85˚F).
your hands, the Detergent will not activate and clean effectively.
NOTE
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.
Using the Dispenser Drawer
The dispenser drawer contains 2 compartments:
• Liquid Fabric Softener
• Liquid or Powder Low-Sudsing, High-Efficiency Detergent
The dispenser automatically dispenses additives at the proper time in the wash cycle. 1. Slowly open the dispenser drawer by pulling the drawer out until it stops.
2. After adding laundry products, slowly close the dispenser drawer. Closing the drawer too quickly could result in early dispensing of additives.
•Avoid overfilling or splashing when adding laundry products to the dispenser. Doing so could result in early dispensing of laundry products.
At the end of the cycle, you may see water in the compartments. This is part of the normal operation of the washer.
NOTE : Do not use bleach in the dispenser drawer.
10
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use Detergent suitable for washing woolens.
Using Detergent
How much Detergent
The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work cloches may need more Detergent, while bath towels usually need less.).
For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.
Adding Detergent
compartment of the dispenser drawer.
beginning of the wash phase.
water temperature, water hardness, size and soil level of the load. , as it can lead to oversudsing and detergent residue being left on
<![endif]>ENGLISH
11
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Using Bleach Check fabric care labels for special instructions.
AVAILABLE BLEACH TYPE
use.
DEPOSITING BLEACH
on the box.
bleach following instructions on the box.
Attention
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may affect colors or damage clothing.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing can produce a toxic gas which may cause death.
Do not pour liquid bleach into bleach dispenser.
may stain them. dispensing. softener dispenser.
occur within any washer when the fabric softener comes into by a fault in the machine.
result in stains on your clothes or an unpleasant smell in
.
32)
-up occurring. We recommend a regular WARM or HOT wash
leave residue on the dispenser and contribute to a build-up.
12
Special Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death. To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
•Keep stain removal products in their original labeled containers and out of children’s reach.
•Thoroughly wash any utensil used.
•Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
•Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
•Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
<![endif]>ENGLISH
For successful stain removal:
•Remove stains promptly.
•Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.
•To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.
•Use COLD water on unknown stains because HOT water can set stains.
•Check care label instructions for treatments to avoid on specific fabrics.
•Check for colorfastness by testing stain remover on an inside seam.
•Rinse and wash items after stain removal.
Follow fabric care label instructions
|
Stain Removal |
||
STAIN |
TREATMENT |
||
|
|
|
|
Adhesive tape, chewing gum, |
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or |
||
rubber cement |
nonflammable dry cleaning fluid. |
||
Baby formula, dairy products, egg |
Use product containing enzymes to pretreat or soak stains. |
||
Beverages (coffee, tea, soda, juice, |
Pretreat stain. Wash using COLD water and bleach safe for fabric. |
||
alcoholic beverages) |
|||
|
|
||
Blood |
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using |
||
|
bleach safe for fabric. |
||
Candle wax, crayon |
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed. |
||
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning |
|||
|
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric. |
||
|
|
|
|
Chocolate |
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. |
||
Collar or cuff soil, cosmetics |
Pretreat with prewash stain remover or rub with bar soap. |
||
|
|
|
|
Dye transfer on white fabric |
Use packaged color remover. Wash using bleach safe for fabric. |
||
|
|
|
|
Grass |
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. |
||
Grease, oil, tar (butter, fats, salad |
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply |
||
dressing, cooking oils, car grease, |
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash |
||
motor oils) |
using hottest water safe for fabric. |
||
Ink |
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured |
||
alcohol or nonflammable dry cleaning fluid. |
|||
|
|||
Mildew, scorch |
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly |
||
mildewed fabrics may be permanently damaged. |
|||
Mud |
Brush off dry mud. Pretreat or soak with product containing enzymes. |
||
Mustard, tomato |
Pretreat with prewash stain remover. Wash using bleach safe for fabric. |
||
Nail polish |
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain. |
||
Repeat, replacing paper towels frequently. Do not use on acetate fabrics. |
|||
|
|||
Paint, varnish |
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed, |
||
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing. |
|||
|
|||
Rust, brown or yellow |
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and |
||
discoloration |
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration. |
||
Shoe polish |
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with |
||
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach |
|||
|
|||
|
safe for fabric. |
13
F unction of each Button
BEEPER BUTTON
•Use to select Beeper Pressing the button allows HIGH OFF LOW HIGH respectively.
WATER LEVEL BUTTON
•Use to select the proper amount of water in relation to the weight and type of laundry.
•Automatically controlled,but can be selected manually by pressing the WATER LEVEL Botton.
•WATER LEVEL is automatically selected for FUZZY(normal) program.
The following settings are indicated as the button is
pushed
7 8 9 10 1 2 3 4 5 6 7
TIME LEFT, DELAY START (RESERVATION), ALARM INDICATION
•Time left - During operation, the remaining time is indicated.
•DELAY START INDICATION (RESERVATION) - When DELAY START (RESERVATION) program is selected, it indicates the finishing time. (RES.=DELAY)
•Alarm indication - When an error occurs, an error
message appears to indicate the abnormality. For example, indicates that the lid is open.
AIR DRY
• This function is used to reduce the drying time of the laundry by allowing air to circulate
within the bowl in order to reduce moisture levels.It does not dry the clothes completely.
•Air dry selections light up in sequence as
follows.
60 90 120 60 as the button ispushed.
•Press the button for 3 seconds to select and press the Power botton to cancel the operation.
(refer to page 22)
SOIL LEVEL BUTTON
•This button allows you to select the strength of the wash action.
•Power option selections light up in sequence as
follows Normal Heavy Light Normal as the
button is pushed.
This can be selected for any program.
•Adjustment can be made while washing.
NOTE
TUB DRY |
|
WASH. RINSE. SPIN BUTTON |
|
|
|
• Use this when you |
|
• Use when wash, rinse, spin |
want to dry the |
|
time need to be adjusted. |
empty tub after a |
|
• The time increases when the |
wash. |
|
button is pressed . |
• This can be |
|
• If adjustments are needed |
set/canceled by |
|
during the wash,press the |
pressing the |
|
START/PAUSE button |
WASH button and |
|
before making any changes. |
RINSE button |
|
• When the button is pressed |
simultaneously. |
|
during washing,the |
(refer to page 22) |
|
remaining time is displayed. |
|
|
|
CHILD LOCK FUNCTION
•Use to lock or unlock the control buttons to prevent settings from being changed by a child.
To lock,push the RINSE and SPIN buttons simultaneously and to unlock push them one more time during the washing process.
(refer to page 25)
*For optimizing the washing algorithm, the displaying time may be changed during washing-increased by 8minutes at maximum and decreased by 4 minutes at maximum.
*If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically adds rinsing, and the remaining time may be increased.
*The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
*The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.
14
WASHING CONDITION INDICATOR (OPTION)
•It only operates in FUZZY Program.
•During being detected by the sensor, the LED flashes green, orange
and red in turn. And, after detecting, the LED lights a specific color according to the detecting condition as follows:
If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength, and the LED automatically turns to red.
If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by increasing washing time/strength, and the LED automatically turns to orange.
If the current washing condition is determined as equal to the standard one, the algorithm has no change and the LED turns to green.
POWER(AUTO OFF)
BUTTON
• Use to turn the power on or off.
• Push again and power goes on or off
• The power goes off automatically about 10 seconds after the wash is finished.
<![endif]>ENGLISH
DELAY START (RESERVATION) BUTTON
•Use to set a delayed finishing time.
•The time increases when the button is pushed.
•The following settings are indicated
as the button is pushed 3 |
4 |
5 |
... 11 12 14 16 |
...46 |
48 |
3HOUR.
•To cancel delay time, turn the power switch off.
(refer to page 24)
PROGRAM BUTTON
•Use for selecting wash program.
•This button allows you to select 8 different programs for different kinds of laundry and dirtiness.
•program selections light up in sequence as
follows: FUZZY(Normal) |
WOOL |
|
QUICK WASH |
JEANS |
SMART |
CLEANING SILENT |
FAVORITE |
|
TUB CLEAN |
FUZZY(Normal) etc. |
Select the desired program by pressing the button.
START/PAUSE BUTTON
•Use to start or pause the washing process.
•Repeats start and pause by pushing the button.
*Because the detecting ability of the sensor may be decreased by using it for a long time, periodically use TUB CLEAN course to clean the tub. (refer to page 21)
*Even if the water level is changed by the user in FUZZY(Normal) Program, the sensor will still work. The sensor algorithm may differ according to models.
*The control panel may differ according to different models.
15
Washing Programs
Washing |
|
Add |
|
Add |
|
the |
|
||
Programs |
|
|
the Detergent |
|
|
laundry |
|
||
|
|
|
|
|
(Normal Wash) |
1 |
2 |
|
4 |
|
|
|
|
|
Used for normal loads, this |
|
|
|
• Add the appropriate |
mode automatically selects the |
|
|
|
|
most appropriate conditions |
|
|
|
quantity of Detergent |
and completes the sequence |
|
|
|
as indicated by the |
in one operation. The built-in |
|
|
|
WATER LEVEL. |
sensor detects the size of the |
|
|
|
Or follow the |
load and the ideal wash |
|
|
|
Detergent |
power and wash, rinse and |
|
|
|
manufacturer’s |
spin times are set accordingly. |
|
|
|
instructions |
Use this program for washing |
1 |
3 |
2 |
5 |
|
|
• Select the |
• Use neutral |
|
delicate fabrics such as lingerie and |
|
|
||
woolens. (wash only “water |
|
|
WOOL |
Detergent |
washable” clothes) |
|
|
program on |
appropriate for the |
Before washing your woolens |
|
|
the Control |
laundry. |
|
|
panel. |
• When washing |
|
check the care label for the |
|
|
||
|
|
|
woolens use a mild |
|
washing instructions. |
|
|
|
|
|
|
|
Detergent |
|
(wash only water washable clothes) |
|
|
|
recommended for |
|
|
|
|
washing wool. |
|
1 |
3 |
2 |
5 |
Use this mode when washing |
|
|
• Select the |
• Add the appropriate |
lightly soiled clothes for a short |
|
|
QUICK |
quantity of Detergent |
time. The highly recommended |
|
|
WASH |
as indicated by the |
|
|
program on |
WATER LEVEL. |
|
laundry amount is under 2.0kg. |
|
|
||
|
|
the Control |
Or follow the |
|
|
|
|
||
|
|
|
panel. |
Detergent |
|
|
|
|
manufacturer’s |
|
|
|
|
instructions |
|
1 |
3 |
2 |
5 |
Use Jean program when |
|
• Spread |
• Select the |
|
washing Jeans of different sizes |
|
the jean |
JEANS |
|
|
|
evenly in |
program on |
|
|
|
the tub |
the Control |
|
|
|
|
panel. |
|
Use this program to increase |
1 |
3 |
2 |
5 |
|
|
|
|
|
rinsing performance. |
|
|
• Select the |
|
This would include underwear |
|
|
|
|
|
|
SMART |
|
|
and baby clothes. |
|
|
|
|
|
|
CLEANING |
|
|
If someone has sensitive skin or |
|
|
|
|
|
|
program on the |
|
|
skin trouble,use this program. |
|
|
Control panel. |
|
16
|
|
|
|
Close the lid |
Finish |
Caution & Note |
||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
5 |
|
6 |
|
• If water is already in the tub, or putting |
|
|
|
|
|
|
|
|
|
wet laundry into the tub before starting |
|
|
|
|
|
|
|
|
will increase the WATER LEVEL. |
|
• The pulsator rotates for |
• Water will be |
• When the wash |
• With lightweight bulky loads, WATER |
||||
|
8 seconds to detect the |
supplied for 2 |
program ends, the |
LEVEL can be set low. |
||||
|
laundry load. |
minutes after the |
buzzer will ring |
|
||||
|
• Then the WATER LEVEL |
start of the wash to |
for 10 seconds |
|
||||
|
and the amount of |
supplement the |
before the Power |
|
||||
|
Detergent to be used |
water the laundry |
goes off |
|
||||
|
will be shown and |
has absorbed. |
automatically. |
|
||||
|
water will be supplied. |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• When setting the WATER LEVEL |
|
4 |
|
6 |
|
7 |
|
manually, do not set to Medium to |
|
|
|
|
|
|
|
|
|
prevent damage to laundry. |
|
|
|
|
|
|
|
|
• Washing with HOT water may damage |
|
|
|
|
|
|
|
|
the laundry (Water is set to cold |
|
|
|
|
|
|
|
|
automatically). Ensure that the load is |
|
|
|
|
|
|
|
|
under 2kg. |
|
|
|
|
|
|
|
|
• In order to avoid damage to laundry, |
|
|
|
|
|
|
|
|
the spin cycle may appear slow. |
|
|
|
|
|
|
|
|
This also avoids wrinkles and clothing |
|
|
|
|
|
|
|
|
may still contain some water. This is |
|
|
|
|
|
|
|
|
normal. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• When static pressure of water is more |
|
|
|
|
|
|
|
|
than 2kg/cm2, the QUICK WASH course |
|
4 |
|
6 |
|
7 |
|
||
|
|
|
|
will be within 19min. |
||||
|
|
|
|
|
|
|
|
|
4 |
6 |
7 |
4 |
6 |
7 |
<![endif]>ENGLISH
17
SOAK Wash
Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. SOAK mode can be used with FUZZY or JEAN or SMART CLEANING or SILENT or FAVORITE program.
1 Press the POWER (AUTO OFF) button to turn power on.
2 Press the PROGRAM button to select the washing program.
3 Press the WASH button, to select SOAK program.
•Keep pressing the WASH button until the light turns on ‘SOAK’ and ‘WASH’ simultaneously as next image.
|
• SOAK program only works when socking time is 40, 50 or |
|
60 minutes. |
4 Add the Detergent. |
• Add the appropriate quantity of Detergent as the Detergent |
|
manufacture instruction. |
5 Add the laundry and press the START/PAUSE button.
|
• The WATER LEVEL will be shown and water will be |
|
supplied. |
6 Close the lid. |
• Water will be supplied for 2 minutes after the start of the |
|
wash to supplement the absorbed water by the laundry. |
Finish |
• When the wash program ends, the buzzer will ring for |
|
10seconds before the Power goes off automatically. |
NOTE
• Order of Soak-Wash timing
Soak-Wash
|
|
|
|
|
|
|
|
Lamp |
|
|
|
|
|
min |
min |
min |
min |
min |
min |
min |
min |
Off |
min |
min |
min |
min |
min |
•Select soaking time 40minutes, 50minutes, or 60minutes (including washing time) by pressing the Wash button repeatedly.
•If necessary, select the times of Rinse and the time for Spinning by pressing the Rinse or Spin buttons till you reach the desired times.
18
FAVORITE Wash
Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the normal cycle memory and then recall it for use at a later time.
<![if ! IE]><![endif]>ENGLISH
1 Press the POWER (AUTO OFF) button to turn power on.
2 Select the FAVORITE program.
3 Select your FAVORITE wash conditions.
•Press the WATER LEVELbutton to select WATER LEVEL.
•Press the WASH button, the RINSE button & the SPIN button to select wash time, rinse time & spin time respectively you want to store.
4 Press the START/PAUSE button to store & start your FAVORITE wash cycle. Power turns off automatically after wash.
NOTE
To recall your FAVORITE cycle.
1.Press POWER on.
2.Select the FAVORITE cycle by pressing the PROGRAM.
3.Press the START/PAUSE button. Then the wash cycle starts.
19
SILENT Wash
Use this program to wash quietly in SILENT especially during late night and dawn.
1 Press the POWER (AUTO OFF) button to turn power on.
2 Press the PROGRAM button to select SILENT program.
3 Add the laundry into the washing tub.
4 Press the START/PAUSE button.
5 Add the Detergent and close the lid.
NOTE
•SILENT program takes longer washing time than FUZZY(Normal) program.
•To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.
20
TUB CLEAN
If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer.
Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.
1 Press the POWER (AUTO OFF) button to turn power on.
<![endif]>ENGLISH
2 Press the PROGRAM button to select the TUB CLEAN program.
3 Press the START/PAUSE button. • Left time is displayed.
4 After 10 minutes of water supplement. Add the oxygenated bleach (about 300 m ).
•Do not use Detergent box.
•Do not place any laundry inside tub.
5 |
Close the lid. |
• When the lid is open the machine will not operate, and an |
|
|
alarm signal will remind you to close the lid. |
NOTE
•Before using this program remove lint inside lint filter.
•When using this program, do not place any laundry inside tub.
•This program takes about 3 hours to be completed.
•After using this program, remove dirt inside filter.
•After finishing this program, open the lid of wash to remove irritant odor.
•Do not pour bleach into the tub directly. It might cause damage the tub.
•Do not leave diluted oxygenated bleach inside tub for long time.
It rusts the tub must drain the remained diluted oxygenated water out.
•Use this program once for every month.
•Do not use this program repeatedly.
21
AIR DRY
AIR DRY for your laundary.
1 |
Press the POWER (AUTO OFF) button to turn power on. |
|
2 |
When you press the Air dry button for 3 seconds, the Air dry course will be |
|
|
selected. |
• When the Air dry is selected, other buttons will be inactive. |
|
|
• If you want to cancel the Air dry function, press the Power button. |
3 |
Press the START/PAUSE button. |
|
4 |
When the Complete buzzer goes off, the power will automatically be turned |
|
|
off in 10 seconds. |
|
NOTE
When you select Air dry foir more than 60 minutes
1)You can reduce the drying time by minimizing the moisture in the laundry.
2)Always keep the laundry amount to 2kg or less and make sure to spread it out evenly.
3)Select 60 minutes for cotton laundry and 120 minutes for synthetic fiber laundry for effective Moisture removal.
TUB DRY
1 |
Press the POWER (AUTO OFF) button. |
2 |
When you press the Wash and Rinse button simultaneously, the Tub Dry course |
|
will be set or canceled. |
|
• When you select the Tub Dry, do not put any laundry in the drum. |
|
• When Tub Dry is selected, other buttons will be inactive. |
3 |
Press the START/PAUSE button. |
4 |
When the Complete buzzer goes off, the poser will automatically be turned off in |
|
10 seconds. |
NOTE
When you select Tub Dry
1)Use this function to minimize the growth of mold from the residual moisture within the laundry.
2)When you select the Tub Dry course, do not put any laundry or detergent in the drum.
3)It is good to use this about once a week.
22
Option Washing
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.
1 Press the POWER (AUTO OFF) button to turn power on.
2 |
Only Wash |
Only Rinse |
Only Spin |
|
Press the WASH button to |
Press the RINSE button to |
Press the SPIN button to |
|
select the desired timing. |
select the desired times of |
select the desired times of |
|
|
rinse. |
spin. |
|
Only Wash,Rinse |
Only Rinse,Spin |
Only Drain |
|
Press the WASH button to |
Press the RINSE button to |
When you want to only |
|
select the desired timing. |
select the desired times of |
drain, wait until the water |
|
|
rinse. |
in the washing tub drains |
|
|
|
completely. |
|
Press the RINSE button to |
|
|
|
select the desired times of |
Press the SPIN button to |
|
|
rinse. |
select the desired times of |
|
|
|
spin. |
|
|
You can use this option |
|
|
|
for preventing wrinkles of |
|
|
|
laundry |
|
|
3 Press the WATER LEVEL button, to control the water level according to the amount of laundry. If you do not choose anything, it is set the middle water level automatically.
4 Add the laundry into the washing tub.
5 Press the START/PAUSE button.
6 Add the detergent and close the lid.
NOTE
•When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained completely. Then press the START/PAUSE button.
•If you do not specify the water level, then Medium will be automatically selected.
<![endif]>ENGLISH
• If only Rinse is selected, the process will start from Water Supply. |
23 |
DELAY START (RESERVATION) Wash
DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation. The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time , not the start time.
1 |
Press the POWER (AUTO OFF) button to turn power on. |
2 |
Press the PROGRAM button to select the washing program. |
|
• Select the program for laundry on the Control panel. |
|
This program will not work in WOOL and TUB CLEAN |
|
Program. |
3 |
Press the DELAY START (RESERVATION) button. |
•The light will ‘DELAY’ turn on and ‘TIME LEFT’ will be marked.
• Press the button repeatedly to set the desired finishing time. For example, To finish washing in 9 hours from now, by make the number 9:00 pressing the DELAY START (RESERVATION ) button repeatedly.
(RES.=DELAY)
4 Add the Detergent. • Add the appropriate quantity of Detergent as the Detergent manufacture instruction.
•When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid
5 |
Add the laundry and press the START/PAUSE button. |
||
|
|
• When you press the START/PAUSE button the light will |
|
|
|
blink. |
|
6 |
Close the lid. |
• Water will be supplied for 2 minutes after the start of the |
|
wash to supplement the water the laundry has absorbed. |
|||
|
|
||
|
Finish |
• The washing will be finished according to the delayed time. |
NOTE
•Finishing time can be delayed from 3~48 hours. Delaying from3~12 hours can be done in 1 hour time intervals and from 12~48 hours in 2 hour time intervals.
• If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
•To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the DELAY START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.
•When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning program . (The laundry will be wrinkled if left for a long time after spinning.)
24