LG WD-8050F, WD-8052X User Manual
Washing Machine
OWNER'S MANUAL
MODEL : WD-8050F/8052X
P/No.: 3828ER3001M
Thank you for purchasing LG Fully Automatic Washer.
Please read your owner's manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record model number and serial number of washing machine.
M
K
3
Specification
P/No.3828ER3001M
(For detergent and
fabric softener)
Drawer
Lower cover cap
Drum
Drain hose
•
If the supply cord is damaged,
it must be replaced by the
manufacturer or its service
agents or similarly qualified
person in order to avoid a
hazard.
Power plug
Door
Leveling legs
Lower Cover
Control panel
Drain plug
Drain pump filter
WD-8050F WD-8052X
Name Front loading washing machine
Power supply 220-240V, 50Hz
Size 600mm(W) × 600mm(D) × 850mm(H)
Weight 67kg
Wash capacity 7.0kg 6.0kg
Heating 2200W
Wash speed 45rpm
Spin speed 400 / 600 / 800 rpm
Water consumption 67L(9.6L/kg) 67L(11.2L/kg)
Permissible water pressure 0.3-10kgf/cm2(30-1000kPa)
Accessories Inlet hose (1EA), Spanner (1EA)
❈ The appearance and specifications may be varied without notice to raise the units quality.
Contents
Product Features..........................................................................................................2
Specification ................................................................................................................ 3
Installation.................................................................................................................... 4
Warnings.......................................................................................................................6
Preparing your laundry / Adding detergent.................................................................. 7
Function of each button............................................................................................... 8
How to use your washing machine............................................................................ 10
Maintaining ................................................................................................................12
Trouble-shooting guide.............................................................................................. 14
2
Product Features
P/No.3828ER3001M
More economical by Fuzzy Logic System
Fuzzy Logic System detects the amount of load and
water temperature, and then determines the optimum
water level and washing time to minimize energy and
water consumption.
Low noise speed control system
By sensing the amount of load and balance, evenly
distributes load to minimize the spinning noise level.
Child-Lock
The Child-Lock system has been developed to prevent children from pressing any button to change the
programme during operation.
Auto Restart
Although the washing machine is turned off by a
power failure, it restarts automatically in its stopped
process when power is supplied again.
Jumbo Drum
LG's jumbo drum can wash about 40% more per load
than conventional washing machine. A bigger drum
improves the wash performance.
Rubber seal
Hose connector
Used the horizontal faucet
Horizontal faucet
Extension faucet
Square faucet
Upper
Connector
Rubber
packing
Fixing screw
Rubber packing
Upper
Connector
Water supply
hose
Plate
Upper
Connector
5
P/No.3828ER3001M
■
Connecting the inlet hose
1.
Unscrew the fixing screw to
attach the faucet.
2.
Push the connector up till the
rubber packing is in tight
contact with the faucet.
Then tighten the 4 screws.
3.
Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the faucet and then tighten it by
screwing it to the
right.
• Make sure that the rubber seal
is inside the hose connector.
• Your machine comes with only
cold water connection.
• Make sure that there are no
kinks in the hose and that it is
not crushed.
■
Connecting the inlet hose
• Two rings are supplied with the water inlet hose in the
valve connector in order to prevent water leaks.
• Your machine comes with only cold water connection.
Connect to cold water using the inlet valve.
• Check water tightness of washing machine connections
by turning the tap completely on.
• Periodically check the condition of the hose and replace
the hose if necessary.
• Make sure that there are no kinks in the hose and that it
is not crushed.
(How to connect the hose of screw type.)
Leveling leg
Higher Lower
Leveling leg
4
Installation
P/No.3828ER3001M
■
Removing the transit bolts
• To protect the washer during transportation, the special 4 bolts are locked. Before operating the washer, remove the bolts. (If they are not removed, it may cause heavy vibration, noise and malfunction)
1
.
Locate the 4 bolts that secure the washer.
2
. Unscrew the 4 bolts with a spanner provided.
3
. Take out the 4 bolts
4
. Keep the transit bolts and spanner for future use.
■
Level adjustment
• If the washer is not levelled, it could cause noise or vibration.
1.
Select a place for installation
• Place it on a firm and even floor.
• Place it more than 2cm away from the wall
2.
Check the gap
• Ensure all feet are firmly on the floor.
3.
After adjusting the level, check it by shaking the
washer. Readjust the level if necessary.
❈ The base opening must not be obstructed by carpeting when
the washing machine is installed on a carpeted floor.
❈ Leveling should be done within 1.5 degree angle.
■
Water drain
• Hook over the edge of a sink using the plastic hose hanger supplied
with the machine.
• Make sure there are no kinks in the hose and that it is not crushed.
Secure the hose so that it can not be dislodged while the appliance is running.
• The drain hose should not be placed higher than 85cm above the floor.
■
Electrical connection
• Do not use an extension cord or double adapter.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly
qualified person in order to avoid a hazard.
• Always unplug the machine and turn off the water supply after using.
• Connect the machine to an the exclusive AC 220 – 240V outlet with ground terminal.
•
If the appliance is supplied from a cord extension set or electrical portable outlet device,
the cord extension set or electrical portable outlet device should be positioned so it is not
subject to splashing or ingress of moisture.
• If a stationary appliance is provided with a supply cord and a plug, the instructions shall
state that the appliance must be positioned so that plug is accessible.
Loading...