LG WD14030D User Guide

4
1
2
3
5
7
1 2
3 4
6
ca. 100 cm ca. 100 cm
ca. 145 cm ca. 145 cm
ca. 105 cm ca. 105 cm
min. 60 cm
max. 100 cm
min. 60 cm
max. 100 cm
60 – 100 cm
Hose
Retainer
Tie
strap
max. 100 cm min. 60 cm
Owners Manual
WD14030D
Safety instructions for use
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it
into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. It has not been designed for use in commercial or industrial applications, (for example, Beauty salons Laundromats etc). Use the appliance only with cold drinking grade water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Never modify the appliance as this is dangerous.
• This appliance is heavy. Transport with care and ensure that the transit bolts are re fit ted during the machines delivery to any new location.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or par ts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage. Unbalanced mass may create heavy vibrations. If heav y vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• Do not spray or use stain remover products near or directly on the machine as it can damage the machines finish.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in the tub after a whole cycle resulting in fire during drying.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas. Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage or stain the clothes.
• After washing, keep the drum door open to protect the door seal.
• There may be a danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer ser vice using original replacement parts.
• When disposing of your old machine, the power cable must be capped or cut off, and the door lock must be made unusable in order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. Do not use the machine as it may impose an electric shock or fire hazard.
• The lower filter cover as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. There is a danger of poisoning.
Remove Packaging
Requirements for installation site
Transit bolts
Electrical connection
Connecting water supply hose
• The appliance is fitted with transit bolts to prevent internal damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using the washing machine.
• When unpacking the base, be sure to remove the additional packing support in the middle of the base packing.
Store original packing for future move. Dispose of packing material according to local regulations.
Unscrew the 4 bolts using the spanner supplied.
Keep the 4 bolts and the spanner for the future use. Ret transit bolts before transporting the appliance.
Level floor: Permissible floor gradient under entire washing machine is 1˚ .
Power socket: Must be within 100 cm of either side of location of washing machine. Do not overload the socket with more than one appliance.
Additional Clearance: For wall, floor and door space is needed. (10cm: rear / 2cm:right & left side). Do not place or store laundry pro­ducts on top of the washing machine at any times. They can damage the finish or controls of the machine.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualied person to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
Repairs to the washing machine must only be carried out by qualied personnel. Repairs carried out by inexpe - rienced persons may cause injury or serious malfunctioning. Contact your local service centre.
Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine standing at room temperature for a few hours before putting it into operation.
• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and replace the hose if necessary.
• Make sure that there is no kink on the hose and that it is not crushed.
When your washing machine has two valves:
• If the washing machine has two valves, power saving is achieved through using hot valve.
Water supply pressure must be between 1.0-8 bar (100kPa~800kPa)
Don’t strip or crossthread when connecting inlet hose to the valve.
If the water supply pressure is more than 800kPa, a decompression device should be installed.
• Proper level-adjustment of the washing ma­chine prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.
• If the floor is uneven, adjust feet as required. (Do not insert pieces of wood etc. under the feet). Make sure that all four feet are stable and resting on the floor. Then check that the appliance is perfectly level. (Use a spirit level).
Level adjustment
To prevent internal dama­ge during transport, the special 4 bolts are locked. If they are not removed, it may cause heavy vibrati­on, noise and machine to malfunction.
Installation of drain hose
@
Name of product Front loading washing machine
Power supply 240 V~, 50 Hz
Size WxDxH mm: 600 x 640 x 850
Weight 65 kg
Max. Watt
2400 W (Wash)
Wash capacity 8.5 kg
Water consumption 73 l (8.6 l / kg)
Permissible water pressure 1.0-8 bar (100-800kPa)
Technical Specification
i
If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the tap into the adaptor.
i
i
The hose supplied with the machine must be used. Old hoses may not be reused
Close the holes with the caps supplied.
Remove the 4 bolts along with the rubber bungs by slightly twisting the bung.
P/No. :MFL59755514
n The external hot water supply MUST NOT exceed 70 deg C n Permissible cold water temperature : 4-25˚C n No further backflow protection required for connection to the water supply.
e The appearance and specifications may be varied without notice to lmprove the units quality. e Specifications subject to change by manufacturer.
CAUTION
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concer­ning use of the appliance by a person responsible for their safety.
• The drain hose should not be placed higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause abnormal noise and cause the machine to malfunction and leak.
Safety instuctions for the installation
Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from obstruction by carpeting if the washing machine is installed on a carpeted oor. In countries where there is a risk of cockroach infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is not impeded by carpets, rug etc.
Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel (85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
The washing machine must not be installed in rooms where the temperature may drop below 0°C.
Please ensure that when the washing machine is installed, that a Service Technician can gain easy access in the event of a break - down.
Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse.. That is, a single outlet supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specications of this owners manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or re. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no oor drain (gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic lm, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not allow children to play inside the bowl as they may become trapped.
CAUTION about the floor surface
The installation surface must be clean, dry and level.
Install washing machine on a flat hard floor.
Poorly constructed timber base floors can contribute to excessive noise and vibration.
Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
The washing machine must be perfectly level and firmly in position.
It must not “see-saw” across corners under load.
The installation surface must be clean, free from floor wax and other lubricant coatings.
Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
N
Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump. Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal. Vibrating noise Have all transit bolts and packing been removed? Water leaks. Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary. Excessive suds Too much detergent or unsuitable detergent. Washing machine does not start Power cord may not be plugged in or connection may be loose. Washing machine won’t spin Check that the door is shut.
Check that foreign objects may be blocking the drain causing the water not to drain out. Door does not open Once started, the door can not be opened for safety reasons.
At the end of the cycle or when Start Pause is pressed, wait one or two minutes before
opening the door to allow the electric locking mechanism time to release.
Troubleshooting
• Water supply is not adequate in area
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The lter of the inlet hose(s) are clogged.
Check another tap in the house. Fully open tap.
Straighten hose(s). Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain lter is clogged.
Clean and straighten the drain hose. Clean the drain filter. For more detailed information, please refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection and correction system. If individual heavy articles are loaded (ex. bath mat, both robe, etc.), this system may stop spinning or even interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle.
• Floor is unstable.
Feet are not adjusted
Add 1 or 2 similar items to help balance
the load.
Rearrange load to allow proper spinning
The oor should be a solid surface. Adjust the feet so that the machine does not rock from side to side or front to back.
• Is the door opened or not completely closed?
Close the door completely.
If the “ ” does not clear, call for
service.
Unplug the power plug and call for service.
• Water overlls due to the faulty water valve.
Close the water tap. Unplug the power plug. Call for service.
Restart the cycle.
• Water level sensor has malfunctioned.
• Over load in motor.
• The washer experienced a power failure.
Please read safety instructions carefully before operating the machine.
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
Call for service.• Water leaks
1
2
3
1 2 3 4 5
1 3
Program
Fabric Type
Water Temp.
(Option)
Cotton
Lightly soiled clothing and small loads
Cotton
Quick
Synthetic
Baby Care
Delicate
Quick 30
Duvet
Hand Wash
Wool
Color fast garments (shirts, nightdresses, pajamas...)and lightly soiled white cotton (underwear)
Polyamide, Acrylic, Polyester
Lightly soiled baby wear
Delicate laundry easily damaged
“Hand wash” marked delicate and wool laundry
Machine washable woolens with pure new wool only
Colored laundry which is lightly soiled fast
Cotton bedding with filling duvet, pillow, blanket, sofa cover with light filling
- Time Delay
- Intensive
- Soak
- Pre Wash
- Crease Care
- Rinse+Spin
- Medic Rinse
- Time Delay
- Intensive
- Crease Care
- Rinse+Spin
1 king size (9 Tog)
40°C (Cold, 30°C, 60°C, 95°C)
Rating
Less than 2.0kg
Less than 4.5kg
Less than 7kg
40°C
(Cold, 30°C,
60°C)
30°C
(Cold, 40°C)
30°C
(Cold, 40°C)
40°C
(Cold, 30°C)
40°C
(Cold, 30°C)
60°C
(40°C, 95°C)
Maximum Load
Option
1
2
1 2 3 4 5
5
2
1 2 3 4 5
4
B
A
C
Sor t the laundr y
note washing instruction symbols -
Degree of soiling -
Type of textile / colour -
Loading the Drum
Check the folds of the f lexible gasket (grey) -
and remove a ny small ar ticles or foreign objects that
may have fallen from items in the previous wash. .
Check all garments for loose items before loading
and ensure that clothes are clear of the door gasket
before closing the door so t hat the clothes or door
gasket are not damaged during the wash.
Fill detergent
Refer to the
written information
on t he detergent's packing
Turn the machine ON
by pressing the Power button
Select a
Program
Select an Option
Pre Wash / Soak / Crease Care / Rinse+Spin
Select Rinse mode
and Washing temperat ure
4 additional programs
Press Star t / Pause to start or pause the washing process
Time Delay / Favorite / Intensive / Medic Rinse
Turn off the water tap
Unscrew the water inlet hose
Pull out the water inlet filter
Clean t he f ilter using a ha rd bristle brush
Pull out the dispenser drawer
Clean t he dispenser drawer under flow­ing water
Clean inside the recess wit h an old toothbrush
Insert the dispenser drawer
Cleaning the water inlet filter
Cleaning the dispenser drawer
Time Delay
Allows you to set the cycle's ending time (by hourly increments) in advance. How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set the finishing time. The machine will t hen automat ically wor k out the turn on time based on t he chosen cycle.
- Press the Start /Pause but ton.
Favorite
- Favorite program allows you to store a customized wash cycle for future use.
- To make a Favorite program:
(1) Select a cycle. (2) Select
The course, washing met hod, number of rinses, spin speed, water temperat ure etc.
(3) Press and hold Favorite progra m button 3 econds (2 beep sounds).
The Favorite program is now stored for future use. To reuse the program, select Favor ite program and press Star t/Pause.
Intensive
If the laundr y is heavily soiled “Intensive”option is ef fective.
- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.
- To use this option, press the intensive but ton once before the wash program is started.
Medic Rinse
For best results or for cleaner rinsing, select the “Medic Rinse” option. This allows the final rinse to be heated to 40 degrees.
Available in the Cotton, Cotton Quick, Synthetic and Baby Care programs. Medic Rinse is set by default in the Baby Care program.
The respective temperature indicator will light up.
Spinning cycle
Temperature
Rinse
Options
Sta rt / Paus eProg ram C ycle
Powe r but ton
Drum
Dispenser drawer
Filter cover.
Control panel
Washing program table
Additional programs
Child Lock
Tub Clean
Change to the desired program, whilst in child lock mode:
Empty the drum completly and close the door
Add anti-limesc ale (Calgon) to the main wash compartment. Close the disp. drawer
Power ON wit h Then press and hold Rinse and Temp. button
Press the Start/Pause but ton to start Tub Clean process
After the cycle is complete, leave the door open to dry
Select this function to lock the buttons on the control panel and t o prevent tampering.
TU B CL EA N is speci al cycle to clean the inside of the washing machine. A higher water level is used in this cyle at higher spin speed. Per form thi s cyc le re gula rly.
Preparation
lightly
heavily
Tighten up the inlet hose
Cleaning the drain pump filter
Washing symbols
Dispenser drawer
Once you have finished cleaning, replace the drawer and run a rinse cycle without laundry or soap.
Cleaning and Maintenance
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock .
DisplayAdditional progra ms
6 3 se c.
6 3 se c.
6 3 se c.
Exterior Proper care of your washing machine can extend its ser vice life. T he out side of the machine can be cleaned with warm water and a neutral non-abrasive household detergent. Immediately wipe off any spillage. Wipe with damp clot h. Avoid striking the surface with sharp objects. Never hose down the machine!
Interior
Dry around the washing machine door opening, flexible gasket and door glass. Run washing machine through a complete cycle using hot water. Repeat process if necessar y.
Cleaning in general
Important: Do not use methylated spirits, solvent s or similar products.
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufact ure’s care label or instructions wh en washing. Intensi ve: If the laundry is heavily soiled “Cotton 40 ˚C +Inte nsive” option is effect ive.
Set program at “Cotton 40˚C+Intensive” option for test in accordance or in conformi ty with AS/NZS 2040.2. For best washing results, we recommend to mix dr y detergent with warm water.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cot ton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Baby Care program. Crease Care: If you want to preve nt creasing, select Crea se C are option. Medic Rinse: For best result s or for cleaner rinsing, you can choose Medic Rinse opt ion. Medic Rinse is set by default in t he Baby Care program.
6 3 se c.
The Beep on /off function c an be set by pressing and holding the Opt ion and Rinse button simultaneously.
Beep on / off
The Beep on /off function c an be set at any time and it is automatically cancelled in t he event of a power cut. The Beep on /off function also works when power is off.
The wool wash cycle of t his machine has been approved by Woolmark for the washing of machine washable Woolmark products provided t hat the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806.
Notes
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
INSERT PL US INTO THE MAIN S SOCKET
Never touch the plug with wet hands! Never remove the plug from t he socket by pulling on the cord.
POSITION DR AIN HOSE.
Position Drain hose as per the installation instruc­tions in this manual
WATE R CONNECT ION
Turn on the water tap
CHECKING THE MACHINE
Never use a defective machine! In case of any failure, first unplug the machine and turn off the water
tap.
PREPARING LAUNDRY AND US ING MACHI NE WITH C ARE
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundr y net
- close zippers
DRUM CARE
- remove ext raneous object s
- leave door open to dry the drum when not in use.
- check the rubber seals regularly
ECOLOG ICAL WASH ING
- make use of the max. washing quant ity
- Please note the washing capacit ies for each cycle as mentioned in the Washing program table.
- do not “pre wash” if possible
- use short program if possible
LAUNDRY WIT H DIFFERENT AMO UNTS OF SOILING
- wash new textiles separately
- do not prewash
- pretreat dir ty spots
- pre wash
Dry flat
Do not bleach
OK. to bleach
Do not tumble dry
Hang to dry
Drip dry
Medium hot ironing
Hot ironing
Do not iron
Washing temperature
Do not wash
Luke warm ironing
B
Main Wash
For Laundry requiring detergent, place recommended dosage in to this compartment. Please note that liquid detergent will enter the tub as it is poured and may not be suitable for a delay start.
C
Sof tener
Do not exceed the MAX-Level. Highly densed softeners are to be diluted with some water. Excessive softener can cause brown or grey spotting on the clothes.
A
Pre Wash
The Pre wash compartment can be used for Normal to heavy soiled clothes, by adding a prewash or normal detergent to this compartment before selecting this wash option with the Cycle.
To activate:
press and hold the Option but tons simultaneously until " " appea rs in the display.
To deactivate:
press and hold the Option but tons simultaneously for 3 seconds until the " " is removed from the display.
Press and hold the Option but tons simultaneously
Press Start/Pause
Select the desired program
Press Start/Pause
Open the lower filter cover and pull out the drain hose.
Unplug the drain hose plug.
Then open t he filter by turning to the lef t
Remove any ext raneous matter from the pump filter
After clea ning, refit the drain filter cap and tighten it by turning it clockwise. insert the drain plug
Close the lower cover
Loading...