LG WD1351RD Owner's manual

OWNER’S MANUAL

WASHING MACHINE

WD1351RD WD1357RD

P/No.: MFL51768190

www.lg.com

Please read this manual carefully before operating your washing machine and retain it for future reference.

ontents

Contents....................................2

Product feature.........................3

Warnings

Important safety instructions .................4

Save these instructions.........................4

Specification.............................6

Installation

Transit bolts ..........................................7

Removing transit bolts ..........................7

Installation place requirement ...............8

Positioning ............................................8

Electrical connection .............................9

Connecting water supply hose............10

Installation of drain hose .....................12

Level adjustment.................................13

In case of auto leveling foot ................13

Care before washing

Before the first washing ......................15

Caring before washing ........................15

Adding detergent

Adding detergent and fabric softener..16

How to use washer

Washing program table.......................18

Control Panel ......................................19

Additional program..............................20

- Power..............................................20

- Program ..........................................20

- Start/Pause .....................................21

- Door Lock .......................................21

- Detecting.........................................21

- Wash...............................................21

- Child Lock .......................................22

- Rinse...............................................22

- Spin.................................................23

- Water Temperature.........................23

- Add Load ........................................24

- Time Delay......................................24

- Tub Clean .......................................25

- Dry ..................................................26

- Display ............................................28

Thank you for buying a LG Fully Automatic Washing Machine.

Please read your owner’s manual carefully, it provides instruction on safe installation, use and maintenance. Retain it for future reference.

Record the model and serial number of your washing machine.

Model No. Serial No. Date of Purchase

Maintenance

The water inlet filter.............................29

The drain pump filter ...........................30

Dispenser drawer................................31

The drawer recess ..............................31

The washing drum ..............................31

The water circulation nozzle &

steam nozzle.......................................32

Cleaning your washer .........................32

Winterizing instructions .......................32

Troubleshooting guide

Diagnosing problems ..........................33

Error messages...................................36

Using SMARTDIAGNOSIS™..............37

Terms of warranty ..................38

roduct Feature

 Direct Drive System

The advanced Brushless DC motor directly drives the drum without belt and pulley.

 6 Motion

Washer is able to perform various drum actions or a combination of different actions depending on the wash program selected. Combined with a controlled spin speed and the ability of the drum to rotate both left and right, the wash performance of the machine is greatly improved, giving you perfect results every time.

 Water Circulation

Sprays detergent solution and water onto the load over and over. Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. The water circulation system uses both water and detergent more efficiently.

 Tilted Drum and Extra Large Door Opening

Tilted drum and extra large opening make it possible to load

and unload clothing more easily.

 Embossing drum & waved lifter

Embossing drum enhances the washing performance and reduces clothes damage.The waved lifter spray and help clothes to enhance washing performance during the washing cycle.

 Automatic Wash Load Detection

Automatically detects the load and optimizes the washing time.

 Built-in Heater

Internal heater helps to maintain water temperature at its optimum level for selected cycles.

 Child Lock

The Child lock prevents children from pressing any button to change the settings during operation.

추가선택, 예약,

arnings

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING!

❊ Do not push down the door excessively, when washer door open.

This could topple over the washer.

• Before installation, check exterior damages. If it has, do not install.

• Do not install or store the washer where it will be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

• Keep small animals away from the appliance.

• Do not leave the washer door open. An open door could entice children to hang on the door or crawl inside the washer.

• Never reach into washer while it is moving. Wait until the drum has completely stopped.

• The laundry process can reduce the flame retardant of fabrics.

• To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible

or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) which may ignite or explode. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oiled clothes.

• Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer.

• When the machine runs high temperature, the front door may be very hot. Don’t touch it.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

• When unplugging power cord, do not pull out by grasping the cord. Otherwise, the power cord may be damaged.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

• Before discarding an old machine unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.

• When a product was under water, Please call service center. The risk of electric shock and fire.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter or otherwise defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer,

follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

WARNING : Improper connection of the equipment-grounding conductor can result in risk of electric

shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

arnings

To minimize the risk of fire in a tumble dryer, the following should be observed:

• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. Washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items. They should not be removed from the tumble dryer or piled or stacked while hot.

• Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and was removers.

• Items containing foam rubber (also known as latex foam) or similarly testured rubber. like materials should not be dried in a tumble dryer on a heat setting. Foam rubber materials can, when heated, produce fire by spontaneous combustion.

• Fabric softeners or similar products should not be used in a tumble dryer to eliminate the effects of static electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.

• Undergarments that contain metal reinforcements should not be placed in a tumble dryer.

Damage to the tumble dryer can result if metal reinforcements come loose during drying. When available a drying rack could be used for such items.

• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.

• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber-coated tennis shoes should not be placed in a tumble dryer.

pecification

 Name : Front loading washing machine  Power supply : 120 V~, 60 Hz  Size : 645 mm(W) x 770 mm(D) x 940 mm(H)  Weight : 86 kg  Wash capacity : 14.0 kg (31 libras)  Dry capacity : 7.0 kg (15 libras)  Max. Watt (Wash / Dry) : 1400 W / 1500 W

0.3 W (The off-mode, The left-on mode)

 Spin speed : Extra Low / Low / Medium / High / Extra High  Water consumption : 161

 Permissible water pressure : 100 - 1000 kPa (1.0 - 10.0 kgf / cm2)

❋ The appearance and specifications may be varied without notice to improve the units quality.

Drum

Drain Pump Filter

Drain Plug

Door

Adjustable Feet

Drain Hose

Control Panel

Lower cover cap

Shipping Bolts Power Plug

• If the supply cord is damaged, it must be replaced by the manufacturer or its authorized service technician in order to avoid a hazard.

Inlet Hose

Dispenser

Inlet hose (2EA) Spanner



Accessories

nstallation

1. To prevent internal damage during

transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs.

• If they are not removed, it may cause heavy vibration, noise and malfunction.

3. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use.

• Whenever the appliance is transported,

the transit bolts must be refitted.

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be removed before using the washer.

󳢹 When unpacking the base, be sure to

remove the additional packing support in the middle of the base packing.

2. Unscrew the 4 bolts with the spanner supplied.

4. Close the holes with the caps supplied.



Transit bolts

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times. Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee.



Removing transit bolts

Washer

Base Packing

Packing Support

nstallation

Level floor :

Allowable slope under entire washer is 1°

Power outlet :

Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance.

Additional Clearance :

For wall, door and floor modeling is required. (10cm : rear / 2cm : right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.



Installation place requirement



Positioning

Install the washer on a flat hard floor. Make sure that air circulation around the washer is not impeded by carpets,rug etc.

• Before placing the washer on tiles, apply a rubber mat under the feet.

• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.

• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.

• The washer must not be installed in rooms where the temperature can drop below 0°C.

• Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.

• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.

• The installation instructions shall state that the openings must not be obstructed by a carpet if it has ventilation openings in the base.

Washer

Drain Hose

Laundry

Tub

approx.

2cm

nstallation

1. Do not use an extension cord or double adapter.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or

similarly qualified person in order to avoid a hazard.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by

inexperienced persons may cause injury or serious malfunctioning. Contact your local service center

• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen

hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing : Store the

washing machine at room temperature for a few hours before putting it into operation.



Electrical connection

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord extension set or electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.

CAUTION

This appliance is not intended for use by young children or infirm persons without supervision. Young Children should be supervised to ensure that they do not play with appliance.

CAUTION

nstallation

1. Unscrew the adapter ring plate and the 4

adapter retaining screws.

2. Push the adapter onto the end of the tap

so that the rubber seal forms a watertight connection. Tighten the adapter ring plate and the 4 screws.

3. Push the water supply hose vertically

upwards so that the rubber packing within the hose can adhere completely to the tap and then tighten it by screwing it to the right.

• Water supply pressure must be between 100 kPa and 1000 kPa (1.0 ~ 10.0 kgf / cm

• Do not strip or crossthread when connecting inlet hose to the valve.

• If the water supply pressure is more than 1000 kPa, a decompression device should be installed.

• Periodically check the condition of the hose and replace the hose if necessary.

Type-A : Connecting Screw-type hose to tap with thread

• Screw the hose connector onto water supply tap.

■ Connecting water supply hose

▶▶

Step1 : Check rubber seal inlet hose

▶▶

Step2 : Connect hose to water tap

• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks. Make sure the connection to taps is sufficiently tight.

Upper connector

Rubber packing

Plate

Water supply hose

Fixing screw

Hose

connector

Rubber seal

Type-B : Connecting Screw-type hose to tap without thread

nstallation

1. Unscrew the adapter ring plate and

the 4 adapter retaining screws.

2. Remove the guide plate if the tap is

too large to fit the adapter.

3. Push the adapter onto the end of

the tap so that the rubber seal forms a watertight connection. Tighten the adapter ring plate and the 4 screws.

4. Pull the connector latch plate down,

push the inlet hose onto the adapter, and release the connector latch plate. Make sure the adapter locks into place.

After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

Use the horizontal tap

Horizontal tap Extension tap Square tap

Ring plate

Guide plate

Latch plate

Type-C : Connecting one touch type hose to tap without thread

▶▶

Step3: Connect hose to washer

• Make sure that there are no kinks in the hose and that they are not crushed.

▶▶

When your washer has two valves.

• The Inlet hose which has red connector is for the hot water tap.

• If the washer has two valves, the energy is saved by using hot valve.

After connecting inlet hose to water tap, turn on the water taps to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature.

nstallation



Installation of drain hose

• The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly.

• Proper securing of the drain hose will protect the floor from damage due to water leakage.

• When the drain hose is too long, do not force back into the washer. This will cause abnormal noise, malfunction, and water leakage.

• When installing the drain hose to a sink, secure it tightly with a string.

• Proper securing of the drain hose will protect the floor from damage due to water leakage should the drain hose become loose.

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the Plug. Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children

about 100 cm

Laundry tub

Hose

Retainer

Tie

strap

max. 100cm min. 60cm

about 105 cm

max. 100 cm

min. 60 cm

about 145 cm

nstallation



Level adjustment

1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.

2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level)

※※

After the washer is level, tighten the lock nuts up towards of the base of the washer. All lock nuts must be tightened.

❊ Diagonal Check

When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

NOTE

Timber or suspended type flooring may contribute to excessive vibration and unblance errors.

NOTE

In the case that the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk that it might fall off.

Adjustable

feet

Adjustable

feet

 In case of auto leveling foot

The right rear foot of the washing machine is an auto leveling foot. Unlike with the adjustable feet, adjusting the auto leveling foot bolt may cause noise or vibration.

❊ Check the auto leveling foot’s state

Case1. Floating from floor

• Raising the front left adjustable foot will press the

auto leveling foot to the floor.

Case2. Auto leveling foot fully pressed

• Raising the adjustable feet at the right front and left

back corners will release the auto leveling foot.

nstallation

 Concrete floors

 Wooden floors (Suspended floors)

• The installation surface must be clean, dry and level.

• Install washer on a flat hard floor.

 Tile floors (Slippery floors)

• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)

※※

Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

• Wooden floors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each foot, at least 15mm thick under the washer, secured to at least 2 floor beams with screws.

• If possible install the washer in one of the corners of the room, where the floor is more stable.

※※

Insert the rubber cups to reduce vibration.

※※

Rubber cups ( p/no. 4620ER4002A) can be purchased from the LG spare parts department.

Important!

• Proper placement and levelling of the washer ensures long, regular and reliable operation.

• The washer must be absolutely horizontal and stand firmly in position.

• It must not “Seesaw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.

※

It can be purchased from hardware suppliers.

Rubber Cup

are before washing

1. Care Labels

Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

2. Sorting

To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Color (White, Lights, Darks) Separate white fabrics from colored fabrics. Lint (Lint producers, Collectors) Wash lint producers and lint collectors

separately.

3. Caring before loading



Caring before washing



Before the first washing

 Combine large and small items in a load. Load large items first. Large items should not be more

than half the total wash load. Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues from the drum that may have been left during manufacturing.

• Check all pockets to make sure that they are empty. Items such as nails, hair clip, matches, pens, coins and keys can damage both your washer and your clothes.

• Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt.

• Close zippers, hooks and strings to make sure that these items don’t snag on other clothes.

• Check the folds of the flexible gasket (gray) and remove any small articles,if any.

• Check inside of the drum and remove any left items in it for next wash cycle.

• Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages.

dding detergent

• Main wash only

➔

• Pre Wash + Main Wash

➔

• Do not exceed the maximum fill line. Close

the dispenser drawer slowly. Overfilling can cause early dispensing of the fabric softener which could stain clothes.

• Do not leave the fabric softener in the

detergent drawer for more than 2 days. (Fabric softener could harden)

• Softener will automatically be added during

the last rinse cycle.

• Do not open the drawer when water is

supplied.

• Solvents(benzene, etc) are not allowable.

1. The Dispenser Drawer

2. Adding Fabric Softener



Adding detergent and fabric softener

Do not pour fabric softener directly on the cloths

NOTE

Detergent for

main wash

Fabric

softener

Detergent for

pre wash

dding detergent

• The detergent should be used according to the instruction of the detergent manufacture.

• If too much detergent is used, too many suds can occur and this will decrease the washing result or cause heavy load to the motor.

• Use powder detergent only for the front loading washer.

❇

If suds occur too much, pleas reduce the detergent amount.

• Detergent usage may need to be adjusted

for water temperature, water hardness, size and soil level of the load. For best results, avoid oversudsing.

4. Water softener

• A water softener, such as Anti limescale (Clagon) can be used to cut down on the use of detergent in extremely hard water areas. Dispense according to the amount specified on the packaging. First add detergent and then the water softener.

• Use the quantity of detergent as for soft water.

❋

Tips Full load : according to manufacturer’s recommendation. Part load : 3/4 of the normal amount. Minimum load : 1/2 of full load.

• Detergent is flushed from the dispenser at the beginning of the cycle.

1) Open the door and Tablets into the

drum.

3. Detergent dosage

5. Using the Tablets

2) Load the laundry into the drum.

3) Close the door.

ow to use washer

•

Recommended courses according to the laundry type.

Cotton

Color fast garments (shirts, night dresses, pajamas...)and lightly soiled white cotton (underwear...)

Pre Wash, Intensive, Normal, Light, Shoes Wash, No Wash, Time Delay, Dry

30˚C

(Cold, 40˚C,

60˚C)

Rating

Sports Wear

Normal, No Wash, Time Delay

30˚C

(Cold)

Dark Wash

This cycle is suitable for lightly soiled clothing. Use this cycle to save energy, by using cold water while ensuring proper washing.

Normal, No Wash, Time Delay, Dry

30˚C

(40˚C, Cold)

Cold Wash

Pre Wash, Intensive, Normal, Light, No Wash, Time Delay, Dry

Cold

Wool

Normal, No Wash, Time Delay

Normal, Light, No Wash, Time Delay

Time Delay, Dry

Normal, Intensive, Pre Wash, Time Delay, Dry, No Wash, Light

40˚C

(Cold, 30˚C)

Duvet

Rinse + Spin

Silent

Normal, No Wash, Time Delay, Dry

Pre Wash, Intensive, Normal, No Wash, Time Delay, Dry

Sanitary

Heavy Duty

Cold

(30˚C, 40˚C)

60˚C

40˚C

(Cold, 30˚C,

60˚C)

60˚C

(40˚C)

This cycle is suitable for sports wear such as jogging clothes and running wear.

Use this cycle to wash “multi-color” clothes to maintain their color

Enable to wash wool fabrics. (Please use detergent for machinewashable woolens).

This cycle is for large items such as bed cover, pillows, sofa covers, etc.

Rinse and Spin

Color fast garments (Shirts, nightdresses, pajamas, etc.) and lightly soiled white cotton (underwear).

Heavily soiled underwear, work clothes, diapers, etc

Heavily soiled cotton fabrics

Maximum

Load

Additional

Option

Proper Temp.

(Option)

Fabric Type

Program

❋ Notes : Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for

garment care.

 Washing program table

Refresh

Cotton mixed, Polyeter mixed Dress shirts, blouses (It just makes wrinkled clothes easy to iron)

Time Delay

–

5 items

Normal, No Wash, Time Delay, Dry

Speed Wash

40˚C

(Cold, 30˚C)

Lightly soiled clothing and small loads

Less than

5.0 kg

Less than

5.0 kg

Less than

3.0 kg

Less than

3.0 kg

Less than

5.0 kg

Less than

5.0 kg

Less than

4.0 kg

1 king size

(9 Tog)

–

ow to use washer

• Press the Power( ) button to start.

• Press the Start/Pause( ) button.

• Initial condition

- Rinse : 3

- Water temperature : 30°C

- Spin : High

- Program : Cotton

• Press the Power( ) button to turn the

washer on.

• Select the desired cycle with the program dial and if required, make any changes to the washing conditions by pressing the buttons accordingly.

For selecting the each conditions, please refer to the page 20 ~ page 28.

• Press the Start/Pause button to commence the cycle.

1. Cotton automatically selected upon power on.

2. Manual Selecting

■ Control panel

ow to use washer

ProgramPower

• Press the Power( ) button to turn power on and off.

• To cancel the Time Delay function, the Power( ) button must be pressed.

• When the Power( ) button is pressed, the washer is ready for Cotton program. And the other initial conditions as follows.

• So, if you want to advance into the washing cycle without changing the program, just press Start/Pause( ) button and then the washer will proceed.

■

Initial program

- Cotton Program / Rinse:3 / 30°C / High

(1)Button: Power (2)Dial: Program (3)Button: Start/Pause

(4)Button: Wash (5)Child Lock (6)Button: Rinse

(7)Button: Spin (8)Button: Temperature (9)Button: Add Load

(10)Button: Time Delay (11)Button: Tub Clean (12)Button: Dry

• 12 programs are available according to the laundry type.

• Dial lamp will light up to indicate selected program.

• When Start/Pause( ) button is pressed, the Cotton program is automatically selected.

- By turning the Program dial, the program is Selected in order of “Cotton – Sports Wear – Dark Wash – Cold Wash – Wool – Duvet – Rinse+Spin – Refresh – Speed Wash – Silent – Sanitary – Heavy Duty”.

For information regarding laundry type for each program, please refer to page 18.

1. Power

2. Initial Program

(1) (3) (4) (6) (7)

(12)(11)(10)(9)(8)

(5)(2)

SMARTDIAGNOSIS™ function is available only for the products with a SMARTDIAGNOSIS™ mark.

ow to use washer

WashStart/Pause

• This Start/Pause button is used to start

wash cycle or pause the wash cycle.

• If temporary stop of wash cycle is needed,

press “Start/Pause” button.

• When in Pause, the power is turned off automatically after 4 minutes.

NB. The door will not open before 1 to 2

minutes when Pause is selected, or at the end of the wash cycle.

1. Start

• Use this option for loads that need pretreatment. This adds 16 minutes of pre washing before draining.

- When using Pre Wash option, do not use a liquid detergent for the main wash. Use powder for the main wash.

1. Pre Wash

• If the laundry is heavily soiled “Intensive” option is effective.

• By selecting the Intensive option, the wash time may be extended, depending on the program selected.

• To use this option select the Intensive option once before the wash programe is started.

2. Intensive

• This option is automatically selected in every course except for Rinse+Spin.

3. Normal

• This cycle is suitable for lightly soiled clothing.

4. Light

• Use this option when you want to wash slippers or shoes.

5. Shoes Wash

2. Pause

• Lights whenever the door of the washer is locked.

• The door can be unlocked by pressing the Start/Pause button to stop the washer.

• The door can be opened after a short delay.

Door Lock

• While the "Detecting" is shown in the display the machine rotates slowly and detects how many laundries are loaded in the drum. It will take a few seconds.

Detecting

ow to use washer

Rinse

• By pressing the Rinse button, the Rinse type can be selected.

• Duvet, Silent perform 4 Rinses.

• Cotton, Sports Wear, Dark Wash,

Cold Wash, Wool, Sanitary, Heavy Duty

perform 3 Rinses.

• Speed Wash performs 2 Rinses.

• Rinse+Spin performs 1 Rinse.

The matching indicator lamp will light up for identification.

Child Lock

Use this option to prevent unwanted use of the washer or to keep cycle settings from being changed while the washer is operating.

• Child Lock can be set by pressing and

holding the Wash and Rinse button

simultaneously. (About three seconds)

• When CHILD LOCK is set, the Child Lock

indicator will appear and all buttons are disabled except the POWER button.

• To deactivate Child Lock system, press and

hold the Wash and Rinse button simultaneously again. (About three seconds)

• To change to the desired program, whilst in Child Lock mode.

1. Press and hold both Wash and Rinse

button together once again. (About three seconds)

2. Press the Start/Pause button.

3. Select the desired program and press the

Start/Pause button again.

• CHILD LOCK lasts after the end of cycle. If you want to deactivate this function, Press and hold the Wash and Rinse button simultaneously for 3 seconds.

Change the desired program

NOTE

ow to use washer

Water Temperature

• By pressing the Temp. button, the water temperature can be selected.

• Water temperature can be selected as below according to the program.

- Cotton

30°C – 40°C – 60°C – Cold

- Silent

40°C – 60°C – Cold – 30°C

- Sports Wear

30°C – Cold

- Wool & Speed Wash

40°C – Cold – 30°C

- Dark Wash

30°C – 40°C – Cold

- Cold Wash

Cold

- Duvet

Cold – 30°C – 40°C

- Sanitary

60°C

- Heavy Duty

60°C – 40°C

The required temperature lamp will light up for identification. For the more detailed information, please refer to the page 18.

Spin

• Spin speed is available according to the Program as follows.

- Rinse+Spin & Speed Wash & Sanitary &

Heavy Duty

Medium - High - Extra High - Extra Low Low

- Cotton & Cold Wash

High - Extra High - Extra Low - Low Medium

- Dark Wash & Silent

Low - Medium - High - Extra High Extra Low

- Sports Wear

Extra Low

- Wool

Low – Extra Low

- Duvet

Medium – Extra Low – Low

• By pressing the Spin button, the spin speed can be chosen.

1. Spin selection

2. No spin

• If “No Spin” is selected, the washer stops after draining the water from the last spin.

The matching indicator lamp will light up for identification.

+ 53 hidden pages