LG WD12595D6 Owner’s Manual
OWNER’S MANUAL
WASHING MACHINE
Please read this manual carefully before operating
your washing machine and retain it for future reference.
WD12590D6
WD12595D6
MFL48165948
www.lg.com
ontents
C
Contents....................................2
Product feature.........................3
Warnings
Important safety instructions .................4
Save these instructions.........................4
Specification.............................5
Installation
Transit bolts ..........................................6
Removing transit bolts ..........................6
Installation place requirement ...............7
Positioning ............................................7
Electrical connection .............................8
Connecting water supply hose..............9
Installation of drain hose .....................11
Level adjustment.................................12
Care before washing
Before the first washing ......................13
Caring before washing ........................13
Adding detergent
Adding detergent and fabric softener..14
Function ..................................16
How to use washer
Control Panel ......................................17
- Power ...............................................18
- Program............................................18
- Start/Pause.......................................19
- Wash ................................................19
- Child lock..........................................20
- Rinse ................................................20
- Spin ..................................................21
- Water Temperature ..........................21
- Medic Rinse......................................22
- Tub Clean.........................................22
- Add Load ..........................................22
- Crease Care .....................................23
- Beep On / Off....................................23
- Favorite.............................................23
- Delay Wash ......................................23
- Door Lock .........................................23
- Display..............................................24
2
Thank you for buying a LG Fully
Automatic Washing Machine.
Please read your owner’s manual
carefully, it provides instruction on safe
installation, use and maintenance.
Retain it for future reference.
Record the model and serial number of
your washing machine.
Model No.
Serial No.
Date of Purchase
Maintenance
The water inlet filter.............................25
The drain pump filter ...........................26
Dispenser drawer................................27
The drawer recess ..............................27
The washing drum ..............................27
The water circulation nozzle ...............28
Cleaning your washer .........................28
Winterizing instructions .......................28
Trouble shooting guide .........29
Using Smart Diagnosis™ ...................32
roduct Feature
추가선택, 예약,
P
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Water Circulation
Sprays detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower
during rinse cycle. The water circulation system uses both water and
detergent more efficiently.
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
Embossing drum & waved lifter
Embossing drum enhances the washing performance and reduces
clothes damage.The waved lifter spray and help clothes to enhance
washing performance during the washing cycle.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level
for selected cycles.
Child Lock
The Child lock prevents children from pressing any button to change the
settings during operation.
3
arnings
!
W
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance
is used by or near children or infirm persons.
Do not allow them to play on, with, or inside this
or any other appliance.
• Keep washer away from fire.
• Do not leave the washer door open.
An open door could entice children to hang on
the door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
• Do not wash articles that have been cleaned in,
washed in, soaked in, or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry
cleaning solvents, kerosene, etc.) which may
ignite or explode.
• Always follow the fabric care instructions
supplied by the garment manufacturer.
• Do not slam the washer door closed or try to
force the door open when locked. This could
result in damage to the washer.
• To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
• If the washer has been exposed to water, call an
authorized service provider to avoid any risk of
fire or electric shock.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
WARNING : Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
4
pecification
S
Shipping Bolts
Inlet Hose
Dispenser
Drum
Door
Drain Hose
Adjustable Feet
Lower Cover Cap
Drain Plug Drain Pump Filter
Name : Front loading washing machine
Power supply : 220 - 240 V~, 50 Hz
Size : 686 mm (W) x 767 mm (D) x 982 mm (H)
Weight : 87 kg
Wash capacity (Max. Watt) : 10 kg (2200 W)
Spin speed : No Spin / Extra Low / Low / Medium / High / Extra High
Water consumption : 102ℓ(10.2ℓ/ kg )
Permissible water pressure : 7.3 ~ 116 PSI (50 ~ 800 kPa)
The external hot water supply must not exceed 65°C
Permissible cold water temperature : 4 - 25˚C
No further backflow protection required for connection to the water supply.
Power Plug
If the supply cord is damaged,
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
Control Panel
Back of Washer
Cold Water Inlet
Hot Water InletAir Vent for Safety
❋ The appearance and specifications may be varied without notice to improve the units quality.
❋ Specifications subject to change by manufacturer.
■
Accessories
Inlet hose
(1EA)
(Option: Hot
(1EA))
Spanner Elbow
Bracket
(for securing
drain hose)
Non-skid
pads
Caps for
covering
shipping bolt
holes
Tie strap
5
nstallation
I
Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the
appliance guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be sure
to remove the additional packing
support in the middle of the base
packing.
Removing transit bolts
Washer
Packing Support
Base Packing
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
2. Unscrew the 4 bolts with
the spanner supplied.
6
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
• Whenever the appliance is transported, the
transit bolts must be refitted.
4. Close the holes with the caps supplied.
nstallation
Washer
approx.
2cm
Drain Hose
Laundry
Tub
I
Installation place requirement
Level floor :
Allowable slope under entire washer is 1°
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
The following clearances should be adhered to.
(10 cm : rear / 2 cm : right & left side)
Do not place or store laundry products on top of
washer at any time.
They can damage the finish or controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Before placing the washer on tiles, apply a rubber mat under the feet.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar
materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an
insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be
inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the
event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the
appliance is stable, and a clearance of approximately 20mm is left between the top of the washer
and the underside of the work-top.
7
nstallation
I
Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or
similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
CAUTION
This appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord
extension set or electrical portable outlet device must be positioned so that it is not subject to
splashing or ingress of moisture.
8
nstallation
I
■ Connecting water supply hose
• Water supply pressure must be between 7.3 ~ 116 PSI (50 ~ 800 kPa).
• Do not strip or crossthread when connecting inlet hose to the valve.
• If the water supply pressure is more than 800 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
▶▶
Step1 : Check rubber seal inlet hose
• Two rubber seals are supplied with the
water inlet hoses.
They are used for preventing water leaks.
Make sure the connection to taps is
Hose
connector
Rubber
seal
▶▶
Step2 : Connect hose to water tap
Type-A : Connecting Screw-type hose to tap with thread
sufficiently tight.
• Screw the hose connector onto water
supply tap.
Type-B : Connecting Screw-type hose to tap without thread
Upper
connector
Fixing screw
Plate
Water supply
hose
Rubber
packing
1. Unscrew the adapter ring plate and the 4
adapter retaining screws.
2. Push the adapter onto the end of the tap
so that the rubber seal forms a watertight
connection. Tighten the adapter ring plate
and the 4 screws.
3. Push the water supply hose vertically
upwards so that the rubber packing within
the hose can adhere completely to the
tap and then tighten it by screwing it to
the right.
9
nstallation
I
Type-C : Connecting one touch type hose to tap without thread
1. Unscrew the adapter ring plate and
the 4 adapter retaining screws.
Ring plate
Guide plate
Latch plate
2. Remove the guide plate if the tap is
too large to fit the adapter.
3. Push the adapter onto the end of
the tap so that the rubber seal forms
a watertight connection.
Tighten the adapter ring plate and
the 4 screws.
4. Pull the connector latch plate down,
push the inlet hose onto the adapter,
and release the connector latch plate.
Make sure the adapter locks into place.
After connecting inlet hose to
water tap, turn on the water taps
to flush out foreign substances
(dirt, sand or sawdust) in the
water lines. Let water drain into a
bucket, and check the water
temperature.
▶▶
Step3: Connect hose to washer
After completing connection, if water leaks from the hose, repeat the same steps.
Use the most conventional type of faucet for water supply. In case the faucet is square
or too big, remove the spacing ring before inserting the faucet into the adaptor.
Horizontal tap Extension tap Square tap
10
• Make sure that there are no kinks in the
hose and that they are not crushed.
▶▶
When your washer has two valves.
• The Inlet hose which has red connector is
for the hot water tap.
• If the washer has two valves, the energy is
saved by using hot valve.
Use the horizontal tap
nstallation
max. 100 cm
min. 60 cm
about 105 cm
about 145 cm
about 100 cm
I
This equipment is not designed for maritime use or for use in mobile installations such as
caravans, aircraft etc.
Turn off the tap if the machine is to be left for any length of time (e.g. holiday), especially if
there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the Plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Installation of drain hose
• When installing the drain hose to a sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage should the drain hose
become loose.
about 100 cm
about 145 cm
about 105 cm
• The end of the drain hose should not be placed
higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the
floor from damage due to water leakage.
• When the drain hose is too long, do not force
back into the washer. This will cause abnormal
noise, malfunction, and water leakage.
min. 60 cm
max. 100 cm
Laundry tub
max. 100cm
min. 60cm
Hose
Retainer
Tie
strap
max. 100cm
min. 60cm
11
Loading...