Lg WD-12316 User Manual

WD-1231(0~9)RDK WD-1431(0~9)RDK

P/No.: MFL38868739

roduct Feature

ontents

Warnings ............................................................................................................3

Specification........................................................................................................5

Installation ...........................................................................................................6

Care before washing .........................................................................................12

Adding detergent...............................................................................................13

Function ..........................................................................................................15

How to use washer............................................................................................16

Maintenance......................................................................................................24

Troubleshooting guide.......................................................................................28

Terms of Warranty ............................................................................................31



Direct Drive System

The advanced Brushless DC motor directly drives the drum without belt and pulley.



Water Circulation

Spray detergent solution and water onto the load over and over. Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. The water circulation system uses both water and detergent more efficiently.



Built-in Heater

Internal heater automatically heats the water to the best temperature on selected cycles.



Child Lock

The Child lock prevents children from pressing any button to change the settings during operation.



Jumbo drum

LG’s jumbo drum can wash about 40% more load than conventional washing machines. A bigger drum improves the wash performance.



More economical by Intelligent Wash System

Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.



Low noise speed control system

By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level.

추가선택, 예약,

40%

arnings

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING!

❊ Do not push down the door excessively, when washer door open.

This could topple over the washer.

• Before installation, check exterior damages. If it has, do not install.

• Do not install or store the washer where it will be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer

or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is used by or near children or infirm persons. Do not allow them to play on, with, or inside this or any other appliance.

• Keep washer away from fire.

• Do not leave the washer door open.

An open door could entice children to hang on the door or crawl inside the washer.

• Never reach into washer while it is moving. Wait until the drum has completely stopped.

• The laundry process can reduce the flame retardant of fabrics.

• To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with

combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) which may ignite or explode. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oiled clothes.

• Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer.

• When the machine runs high temperature, the front door may be very hot. Don’t touch it.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

• When unplugging power cord, do not pull out by grasping the cord. Otherwise, the power cord may be damaged.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

• Before discarding an old machine unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.

• When a product was under water, Please call service center. The risk of electric shock and fire.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter or otherwise defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : To reduce the risk of fire, electric shock, or injury to persons when using

the washer, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

WARNING :

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with

a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

arnings

To minimize the risk of fire in a tumble dryer, the following should be observed:

• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enought to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. Washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items. They should not be removed from the tumble dryer or piled or stacked while hot.

• Items that have been previously cleaned in, washed in, soaked in or spotted with petro/gasoline, dry-cleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and was removers.

• Items containing foam rubber (also known as latex foam) or similarly testured rubber. like materials should not be dried in a tumble dryer on a heat setting. Foam rubber materials can, when heated, produce fire by spontaneous combustion.

• Fabric softeners or similar products should not be used in a tumble dryer to eliminate the effects of static electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.

• Undergarments that contain metal reinforcements should not be placed in a tumble dryer.

Damage to the tumble dryer can result if metal reinforcements come loose during drying. When available a drying rack could be used for such items.

• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.

• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber-coated tennis shoes should not be placed in a tumble dryer.

pecification

란제리

 Name : Front loading washing machine

 Power supply : 220-240V~, 50Hz

 Size : 600mm(W)×645mm(D)×850mm(H)

 Weight : 66kg

 Wash capacity/Max. Watt : Refer to the Rating Label

 Dry capacity/Max. Watt : Refer to the Rating Label

 Spin speed : No Spin/400/800/1000/1200 [WD-1231(0~9)RDK]

No Spin/400/800/1000/1400 [WD-1431(0~9)RDK]

 Water consumption : 144ℓ

❋ The appearance and specifications may be varied without notice to raise the units quality.

Spanner

Inlet hose(1EA)



Accessories

1. To prevent internal damage during

transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs.

• If they are not removed, it may cause heavy vibration, noise and malfunction.

3. Take out the 4 bolts along with the

rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use.

• Whenever the appliance is transported, the transit bolts must be refitted.

2. Unscrew the 4 bolts with the spanner

supplied.

4. Close the holes with the caps supplied.



Removing transit bolts

nstallation

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be removed before using the

washer.

󳢹 When unpacking the base, be

sure to remove the additional packing support in the middle of the base packing.



Transit bolts

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times. Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee.

(Packing support may not be used depending on models.)

nstallation

Level floor :

Allowable slope under entire washer is 1˚

Power outlet :

Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance.

Additional Clearance :

For wall, door and floor modeling is required. (10cm : rear / 2cm: right & left side)

Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.



Installation place requirement



Positioning

Install the washer on a flat hard floor. Make sure that air circulation around the washer is not impeded by carpets,rug etc.

• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.

• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.

• The washer must not be installed in rooms where the temperature can drop below 0°C.

• Please ensure that when the washer is installed, it is easily accessible for the engineer in

the event of a breakdown.

• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.

650

850

600

nstallation

▶Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm

)

▶Don’t strip or crossthread when connecting Inlet hose to the valve. ▶If the water supply pressure is more than 1000kPa, a decompression device should

be installed.

• Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks.

• Check water tightness of washing machine connections by turning the tap completely on.

• Periodically check the condition of the hose and replace the hose if necessary.

• Make sure that there is no kink on the hose and that it is not crushed.



Washing Machine is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.



Connecting water supply hose

1. Do not use an extension cord or double adapter.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or

similarly qualified person in order to avoid a hazard.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service center

• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing machine at room temperature for a few hours before putting it into operation.



Electrical connection

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

CAUTION

NOTE

After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

Rubber seal

Hose connector

nstallation



Normal Tap without thread & screw type inlet hose



Normal Tap without thread & one touch type inlet hose

1. Unscrew the fixing screw to

attach the tap.

2. Push the connector up till the

rubber packing is in tight contact with the tap. Then tighten the 4 screws.

3. Push the water supply hose

vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right.

1. Untighten the upper connector

screw.

2. Push the upper connector up till

the rubber packing is in tight contact with the tap. Then tighten the 4 screws.

3. Connect the water supply hose

to the middle connector, pushing the plate down.

• Your machine comes with only cold water connection.

• Make sure that there are no kinks in the hose and that it is not crushed.

• Make sure that the rubber seal is inside the hose connector.

Upper Connector

Rubber packing

Middle connector

Fixing screw

Guide plate

Connector

Rubber seal

Hose connector

Used the horizontal tap

Horizontal tap

Extension tap

Square tap

Rubber packing

Upper Connector

Middle connector

Plate

Upper Connector

Water supply hose

• In case the diameter of the tap is large remove the guide plate.

• Turn the middle connector not to have water leaked.

• To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down.

nstallation



Installation of drain hose

• The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly.

• Proper securing of the drain hose will protect the floor from damage due to water leakage.

• When the drain hose is too long, do not force back into the washer. This will cause abnormal noise.

• When installing the drain hose sink, secure it tightly with a string.

• Proper securing of the drain hose will protect the floor from damage due to water leakage.

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children

nstallation

1. Adjusting the washing machine level properly prevents excessive noise

and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.

2. If the floor is uneven, adjust the adjustable feet as required. (do not insert

pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level)

※※

After the washer is level, tighten the lock nuts up towards of the base of the washer. All lock nuts must be tightened.

❊ Diagonal Check

When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

NOTE



Level adjustment



Concrete floors



Wooden floors (Suspended floors)

• The installation surface must be clean, dry and level.

• Install washer on a flat hard floor.



Tile floors (Slippery floors)

• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)

※※

Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

• Wooden floors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each foot,

at least 15mm thick under the washer, secured to at least 2 floor beams with screws.

• If possible install the washer in one of the corners of the room, where the floor is more stable.

※※

Insert the rubber cups to reduce vibration.

※※

You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.

Important!

• Proper placement and levelling of the washer ensure long,regular and reliable operation.

• The washer must be absolutely horizontal and stand firmly in position.

• It must not “Seesaw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.

Timber or suspended type flooring may contribute to excessive vibration and unblance errors.

In the case that the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk that it might fall off.

Rubber Cup

are before washing

1. Care Labels

Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

2. Sorting

To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Color (White, Lights, Darks) Separate white fabrics from colored fabrics. Lint (Lint producers, Collectors) Wash lint producers and lint collectors

separately.

3. Caring before loading



Caring before washing



Before the first washing



Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

• Check all pockets to make sure that they are empty. Items such as nails, hair clip, matches, pens, coins and keys can damage both your washer and your clothes.

• Close zippers, hooks and strings to make sure that these items don’t snag on other clothes.

• Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt.

Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing.

• Check the folds of the flexible gasket (gray) and remove any small articles,if any.

• Check inside of the drum and remove any left items in it for next wash cycle.

• Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages.

dding detergent

• Main wash only

➔

• Pre Wash + Main Wash

➔

• Do not exceed the maximum fill line. Close the dispenser drawer slowly. Overfilling can cause early dispensing of the fabric softener which could stain clothes.

• Do not leave the fabric softener in the detergent drawer for more than 2 days. (Fabric softener could harden)

• Softener will automatically be added during the last rinse cycle.

• Do not open the drawer when water is supplied.

• Solvents(benzene, etc) are not allowable.

1. The Dispenser Drawer

2. Adding Fabric Softener



Adding detergent and fabric softener

Do not pour fabric softener directly on the cloths

NOTE

MAXMAX

MAX

dding detergent

• The detergent should be used according to the instruction of the detergent manufacture.

• If too much detergent is used, too many suds can occur and this will decrease the washing result or cause heavy load to the motor.

• Use powder detergent only for the front loading washer.

❇

If suds occur too much, pleas reduce the detergent amount.

• Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load. For best results, avoid oversudsing.

4. Water softener

• A water softener, such as Anti limescale (Clagon) can be used to cut down on the use of detergent in extremely hard water areas. Dispense according to the amount specified on the packaging. First add detergent and then the water softener.

• Use the quantity of detergent as for soft water.

❋

Tips Full load : according to manufacturer’s recommendation. Part load : 3/4 of the normal amount. Minimum load : 1/2 of full load.

• Detergent is flushed from the dispenser at the beginning of the cycle.

1) Open the door and Tablets into the

drum.

3. Detergent dosage

5. Using the Tablets

MAXMAX

2) Load the laundry into the drum.

3) Close the door.

unction



Recommended courses according to the laundry type

Laundry type is the same in Cotton.

60˚C

(Cold, 30˚C,

40˚C, 95˚C)

60˚C

(40˚C)

40˚C

(Cold, 30˚C,

60˚C)

30˚C

(Cold, 40˚C)

30˚C

(Cold, 40˚C)

Cold

(30˚C, 40˚C)

Cold

(30˚C, 40˚C)

Color fast garments (shirts, night dresses, pajamas...)and lightly soiled white cotton (underwear...)

Polyamide, Acrylic, Polyester.

Delicate laundry easily damaged.

Machine washable woolens with pure new wool only.

“Hand Wash” marked delicate and wool laundry.

Colored Landry which is lightely soiled fast.

Cotton bedding with filling, duvet, pillow, blanket, sofa cover with light filling.

❋ Water Temperature : Select the water temperature to the wash cycles.

Always follow garment manufacture’s care label or instructions when laundering.

❋ Intensive : If the laundry is heavily soiled “Intensive” option is effective.

❋ Program setting with “Intensive” option for test in accordance or in conformity with EN60456 and

IEC60456.

❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available

in Cotton, Cotton-Eco and Synthetic Program.

Program

Fabric Type

Maximum Load

Proper Temp.

Option

Rating

4.0kg

3.0kg

2.0kg

5.0kg

1 king size

(9 Tog)

Cotton

Cotton-Eco

Synthetic

Delicate

Wool/Silk

Hand Wash

Quick 30

Duvet

- Soak

- Pre Wash

- Rinse+Spin

- Spin Only

- Dry Only

- Intensive

- Rinse+Spin

- Spin Only

- Dry Only

- Intensive

- Rinse+Spin

- Spin Only

- Intensive

- Rinse+Spin

- Spin Only

- Intensive

ow to use washer

• Press the Power button to start.

• Press the Start/Pause button.

• Initial condition

- Wash : Main wash

- Rinse : 3 times

- Spin :

• 1200 rpm [WD-1231(0~9)RDK]

• 1400 rpm [WD-1431(0~9)RDK]

- Water temperature : 60˚C

- Program : Cotton

• Press the Power button to start.

• Select the conditions which you want to use,

by pressing each button.

For selecting the each conditions, please refer to the page 17~page 23.

• Press the Start/Pause button.

1. Cotton automatically selected upon power on.

2. Manual Selecting

ow to use washer

Program

• 9 programs are available according to the laundry type.

• Lamp will light up to indicate selected program.

1. Power

2. Initial Program

Power

• Press the Power button to turn power on and off.

• To cancel the Time Delay function, the Power button should be pressed.

• When the Power button is pressed, the washer is ready for Cotton program. And the other initial conditions as follows.

• So, if you want to advance into the washing cycle without changing the program, just press Start/Pause button and then the washer will proceed.

■

Initial program

• [WD-1231(0~9)RDK]

- Cotton Program / Main wash / Normal Rinse / 1200 rpm / 60˚C

• [WD-1431(0~9)RDK]

- Cotton Program / Main wash / Normal Rinse / 1400 rpm / 60˚C

• When Start/Pause button is pressed, the Cotton program is automatically selected.

- By turning the Program dial, the program is selected in order of “Cotton - Cotton-Eco Synthetic - Delicate - Wool/Silk - Hand Wash Quick 30 - Duvet - Drain”.

Regarding to the laundry type for each program Please refer to the page 15.

(1) Button : Power (2) Dial : Program (3) Button : Start/Pause (4) Button : Option

(5) Child lock (6) Button : Rinse (7) Button : Spin (8) Button : Temperature

(9) Button : Dry (10) Button : Intensive (11) Button : Time Delay

- Cotton

- Cotton-Eco

- Synthetic

- Delicate

- Wool/Silk

- Hand Wash

- Quick 30

- Duvet

- Drain

(1) (3) (4) (6) (7) (8) (9) (11)(10)(5)(2)

ow to use washer

Start/Pause Option

• This Start/Pause button is used to start wash cycle or pause the wash cycle.

• If temporary stop of wash cycle is needed, press “Start/Pause” button.

• When in Pause, the power is turned off automatically after 4 minutes.

• NB. The door will not open before 1 to 2

minutes when Pause is selected, or at the end of the wash cycle.

1. Start

2. Pause

• While the "Detect" is shown in the display the machine rotates slowly and detects how many laundries are loaded in the drum. It will take a few seconds.

• Available in Cotton, Cotton-Eco and

Synthetic.

Detect

Door Lock

• Lights whenever the door of the washer is locked.

• The door can be unlocked by pressing the Start/Pause button to stop the washer.

• The door can be opened after a short delay.

• By pressing the option

button, only one option function be selected.

1. Soak

• Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty.

• Available in Cotton, Cotton-Eco and Synthetic.

2. Pre Wash

• Use this option for load that need pretreatment. Add 16 minutes pre wash and drain.

- When using Pre Wash option, do not use

liquid detergent in the main wash comportment. Use powder for the main wash.

• Available in Cotton, Cotton-Eco and Synthetic.

3. Rinse+Spin

• Use this option to rinse and then spin.

4. Spin Only

• When you want spin only, select the this option.

5. Dry Only

• When you want dry only, select the this option.

• Available in Cotton, Cotton-Eco, Synthetic and Quick 30.

ow to use washer

Child lock

If you choose to lock the buttons on the control assembly to prevent tampering, this function may be selected.

• Child lock can be set by pressing and holding the Option and Rinse button simultaneously. (About three seconds)

• When child lock is set, all buttons are inoperable except for power button.

• To deactivate Child lock system, press and hold the Option and Rinse button simultaneously again. (About three seconds)

• To change to the desired program, whilst in child lock mode.

1. Press and hold both Option and Rinse

button together once again. (About three seconds)

2. Press the Start/Pause button.

3. Select the desired program and press the

Start/Pause button again.

• The child lock can be set at any time and it is automatically canceled when operational errors occur. Also Child lock works when power is off.

1. Normal

2. Rinse+& Rinse

3. Rinse Hold

Rinse

• By pressing the Rinse button, the Rinse type can be selected.

- Normal

- Rinse

- Normal+Hold

- Rinse++Hold

• Cotton, Cotton-Eco, Synthetic performs 3 Rinses

• Wool/Silk, Hand Wash, Quick 30, Delicate, Duvet

performs 2 Rinses

• Used to additional rinse, which may assist in removing traces of detergent residue.

• By selecting Rinse+or Rinse

function, the Rinse Time and the Rinse water are increased.

• Is selected by pressing the Rinse button repeatedly this function leaves clothes in the washer; suspended in the water after a rinse without entering into spin.

• To proceed through to a drain or spin, once the rinse hold function is completed using to program dial scroll to the required program.

The required lamp will light up for identification.

+ 43 hidden pages