OWNER’S MANUAL
AIR
CONDITIONER
(HEAT PUMP)
Please read this manual carefully before operating your set and retain it for future reference.
Single ceiling suspended air conditioner
<![endif]>TILI OʻZBEK МОВА БЕЛАРУСКАЯ ТІЛІ ҚАЗАҚ НСЬКАÏУКРА ЯЗЫК РУССКИЙ ENGLISH
www.lg.com
P/NO.:MFL70523607
REV.00_200319
<![endif]>ENGLISH
2 |
TIPS FOR SAVING ENERGY |
|
|
|
TIPS FOR SAVING ENERGY
Here are some tips that will help you minimize the power consumption when you use the air conditioner. You can use your air conditioner more efficiently by referring to the instructions below:
•Do not cool excessively indoors. This may be harmful for your health and may consume more electricity.
•Block sunlight with blinds or curtains while you are operating the air conditioner.
•Keep doors or windows closed tightly while you are operating the air conditioner.
•Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
•Speed up the fan to cool or warm indoor air quickly, in a short period of time.
•Open windows regularly for ventilation as the indoor air quality may deteriorate if the air conditioner is used for many hours.
•Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the air flow or weaken the cooling / dehumidifying functions.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
Dealer’s name :
Date of purchase :
IMPORTANT SAFETY INSTRUCTIONS |
3 |
|
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product
! WARNING
It can result in serious injury or death when the directions are ignored
! CAUTION
It can result in minor injury or product damage when the directions are ignored
! WARNING
•Always ground the product. There is a risk of electric shock.
•Do not use a defective or underrated circuit breaker. Use the correctly rated breaker and fuse. There is risk of fire or electric shock .
•Do not use a multi consent. Always use this appliance on a dedicated cicuit and breaker. Otherwise it can cause electric shock or fire.
•For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. Do not disassemble or repair the product by yourself. There is risk of fire or electric shock.
•Always ground the product as per the wiring diagram. Do not connect the ground wire to gas or water pipes lightening rod or telephone ground wire. There is risk of fire or electric shock.
•Install the panel and the cover of control box securely. There is risk of fire or electric shock due to dust , water etc.
•Use the correctly rated breaker or fuse. There is risk of fire or electric shock.
•Do not modify or extend the power cable. If the power cable or cord has scrathes or skin peeled off or deteriorated then it must be replaced. There is risk of fire or electric shock.
•For installation, removal or reinstall , always contact the dealer or an Authorized Service Center. There is risk of fire, electric shock, explosion, or injury.
•Do not install the product on a defective installation stand. Be sure that the installation area does not deteriorate with age. It may cause product to fall.
•Never install the outdoor unit on a moving base or a place from where it can fall down. The falling outdoor unit can cause damage or injury or even death of a person.
•When the product is soaked (flooded or submerged) in water , contact an Authorized Service Center for repair before using it again. There is risk of fire or eletric shock.
•Be sure to check the refrigerant to the used. Please read the label on the product. Incorrect refrigerant used can prevent the normal operation of the unit.
•Don't use a power cable, a plug or a loose socket which is damaged. Otherwise it may cause a fire or electrical shock.
•Do not touch , operate, or repair the product with wet hands. Hold the plug by hand when taking out. There is risk of electric shock or fire.
•Do not place a heater or other heating appliances near the power cable. There is risk of fire and electric shock.
•Do not allow water to run into electric parts. Install the unit away from water sources. There is risk of fire, failure of the product, or electric shock.
•Do not store or use or even allow flammable gas or combustibles near the product. There is
<![endif]>ENGLISH
<![endif]>ENGLISH
4 |
IMPORTANT SAFETY INSTRUCTIONS |
|
|
|
risk of fire.
•Indoor/outdoor wiring connections must be secured tightly and the cable should be routed properly so that there is no force pulling the cable from the connection terminals. Improper or loose connections can cause heat generation or fire.
•Safely dispose off the packing materials. Like screws, nails, batteries, broken things etc after installation or svc and then tear away and thraw away the plastic packaging bags. Children may play with them and cause injury.
•Make sure to check that the power cable plug is not dirty, loose or broken and then only insert the plug completely. Dirty, loose or broken power plug can cause electric shock or fire.
•In outdoor unit the step-up capacitor supplies high voltage electricity to the electrical components. Be sure to discharge the capacitor completely before conducting the repair work. An charged capacitor can cause electrical shock.
•When installing the unit, use the installation kit provided with the product. Otherwise the unit may fall and cause severe injury.
•Be sure to use only those parts which are listed in the svc parts list. Never attempt to modify the equipment. The use of inappropriate parts can cause an electrical shock, excessive heat generation or fire.
•Do not use the product in a tightly closed space for a long time. Perform ventilation regularly. Oxygen deficiency could occur and hence harm your health.
•Do not open the front grille of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.) There is risk of physical injury, electric shock, or product failure.
•If strange sounds, smell or smoke comes from product.Immediately turn the breaker off or disconnect the power supply cable. There is risk of electric shock or fire.
•Ventilate the product room from time to time when operating it together with a stove, or heating element etc. Oxygen deficiency can occur and hence harm your health.
•Turn the main power off and unplug the unit when cleaning or repairing the product. There is risk of electric shock.
•When the product is not to be used for a long time, disconnect the power supply plug or turn off the breaker. There is risk of product damage or failure, or unintended operation.
•Take care to ensure that nobody especially kids could step on or fall onto the outdoor unit. This could result in personal injury and product damage.
•Take care to ensure that power cable could not be pulled out or damaged during operation. There is risk of fire or electric shock.
•Do not place ANYTHING on the power cable. There is risk of fire or electric shock.
•Do not plug or unplug the power supply plug to turn the unit ON/OFF. There is risk of fire or electric shock.
•When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on. Do not use the telephone or turn switches on or off. There is risk of explosion or
fire.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
!CAUTION
•Two or more people must lift and transport the product. Avoid personal injury.
•Do not install the product where it will be exposed to sea wind (salt spray) directly. It may cause corrosion on the product.
•Install the drain hose to ensure that the condensed water is drained away properly. A bad connection may cause water leakage.
•Keep level even when installing the product. To avoid vibration or noise.
•Do not install the product where the noise or hot air from the outdoor unit could damage or disturb the neighborhoods. It may cause a problem for your neighbors and hence dispute.
IMPORTANT SAFETY INSTRUCTIONS |
5 |
• Always check for gas (refrigerant) leakage after installation or repair of product. Low refriger- |
<![if ! IE]> <![endif]>ENGLISH |
|
|
ant levels may cause failure of product. |
|
• Do not use the product for special purposes, such as preserving foods, works of art, etc. It is |
|
a consumer air conditioner, not a precision refrigeration system. There is risk of damage or |
|
loss of property. |
|
• Do not block the inlet or outlet of air flow. It may cause product failure. |
|
• Use a soft cloth to clean. Do not use harsh detergents, solvents or splashing water etc. There |
|
is risk of fire, electric shock, or damage to the plastic parts of the product. |
|
• Do not touch the metal parts of the product when removing the air filter. There is risk of per- |
|
sonal injury. |
|
• Do not step on or put anyting on the product. (outdoor units) There is risk of personal injury |
|
and failure of product. |
|
• Always insert the filter securely after cleaning. Clean the filter every two weeks or more often |
|
if necessary. A dirty filter reduces the efficiency. |
|
• Do not insert hands or other objects through the air inlet or outlet while the product is operat- |
|
ing. There are sharp and moving parts that could cause personal injury. |
|
• Be cautious when unpacking and installing the product. Sharp edges could cause injury. |
|
• If the refrigerant gas leaks during the repair, do not touch the leakaing refrigerant gas. The re- |
|
frigernat gas can cause frostbite (cold burn) |
|
• Do not tilt the unit when removing or uninstalling it. The condensed water inside can spill . |
|
• Do not mix air or gas other than the specified refrigerant used in the system. If air enters the |
|
refrigerant system, an excessively high pressure results, causing equipment damage or injury. |
|
• If the refrigerant gas leaks during the installation, ventilate the area immediately. Otherwise it |
|
can be harmfull for your health. |
|
• Dismantling the unit, treatment of the refrigerant oil and eventual parts should be done in ac- |
|
cordance with local and national standards. Replace the all batteries in the remote control |
|
with new ones of the same type. Do not mix old and new batteries or different types of bat- |
|
teries. There is risk of fire or product failure. |
|
• Do not recharge or disassemble the batteries. Do not dispose off batteries in a fire. They may |
|
burn or explode. |
|
• If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. |
|
Do not use the remote if the batteries have leaked. The chemicals in batteries could cause |
|
burns or other health hazards. |
|
• If you eat the liquid from the batteries, brush your teeth and see doctor. Do not use the re- |
|
mote if the batteries have leaked. The chemicals in batteries could cause burns or other |
|
health hazard. |
|
• Do not let the air conditioner run for a long time when the humidity is very high and a door or |
|
a window is left open. Moisture may condense and wet or damage furniture. |
|
• Do not expose your skin or kids or plants to the cool or hot air draft. This could harm to your |
|
health. |
|
• Do not drink the water drained from the product. It is not sanitary and could cause serious |
|
health issues. |
|
• Use a firm stool or ladder when cleaning, maintaining or repairing the product at an height. |
|
Be careful and avoid personal injury. |
|
<![endif]>ENGLISH
6 |
TABLE OF CONTENTS |
|
|
|
TABLE OF CONTENTS
2 |
TIPS FOR SAVING EN- |
|
19 Auto Changeover Mode - Setting the |
||
|
|
Mode Change Temperature |
|||
|
ERGY |
20 |
Airflow Setting |
||
3 |
IMPORTANT SAFETY IN- |
20 |
Celsius/Fahrenheit Switching |
||
21 |
Temperature Setting/Room Tempera- |
||||
|
STRUCTIONS |
||||
|
|
|
ture checking |
||
7 |
BEFORE USE |
22 |
|||
SUB FUNCTION |
|||||
7 |
Preparing for operation |
|
|
|
|
22 |
Plasma Purification(Optional) |
||||
|
|
||||
7 |
Usage |
22 |
Auto Clean (Optional) |
||
|
|
||||
7 |
Cleaning and maintenance |
23 |
Smart Clean (Optional) |
||
|
|
||||
7 |
Service |
24 |
Individual vane angle control (Optional) |
||
|
|
||||
8 |
PRODUCT INTRODUC- |
|
25 |
TIMER |
|
|
TION |
25 |
Setting the Current Time |
||
8 Name and function of parts |
|||||
25 |
Sleep Timer Setting |
||||
|
|
||||
9 |
Operation Indication Lamps |
25 |
On Timer Setting |
||
10 |
Wireless Remote Controller |
26 |
Off Timer Setting |
||
11 |
OPERATING INSTRUC- |
26 |
To cancel the Timer Setting |
||
|
|
||||
|
TION |
27 |
MAINTENANCE AND |
||
11 How to insert the Batteries |
|
|
SERVICE |
||
11 |
Wireless Remote Controller Mainte- |
27 |
Indoor Unit |
||
|
nance |
28 |
Operation Tips! |
||
11 |
Operating Method |
||||
28 |
When the air conditioner is not |
||||
12 |
OWNER'S INSTRUC- |
||||
|
|
going.... |
|||
|
TION |
29 |
Troubleshooting Tips! Save time and |
||
|
|
||||
|
|
|
|
money! |
|
12 Cooling Mode - Standard Operation |
29 |
||||
Call the service immediately in the fol- |
|||||
|
|
||||
12 |
Cooling Mode - Power Cooling |
|
|
lowing situations |
13Cooling Mode - Comfort Cooling
14Heating Mode
15Dehumidification Mode
16Fan Mode
17Auto Operation Mode
18Auto Changeover Mode
BEFORE USE |
7 |
|
BEFORE USE
Preparing for operation
•Contact an installation specialist for installation.
•Use a dedicated circuit.
Usage
•Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not expose occupants, pets, or plants to direct airflow for extended periods of time.
•Due to the possibility of oxygen deficiency, ventilate the room when used together with stoves or other heating devices.
•Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices, food, pets, plants, and art objects). Such usage could damage the items.
Cleaning and maintenance
•Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
•Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
•When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a very high speed during operation. There is a possibility of injury if the unit’s power is accidentally triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
<![endif]>ENGLISH
<![endif]>ENGLISH
8 PRODUCT INTRODUCTION
PRODUCT INTRODUCTION
Name and function of parts
4 6 7
2
5
1 4
3
8
1 Indoor unit
2 Outdoor unit
3 Remote controller
4 Inlet air
5 Discharge air
6 Refrigerant piping, connection electric wire
7 Drain pipe
8Ground wire
Wire to ground outdoor unit to prevent electrical shocks.
PRODUCT INTRODUCTION 9
Operation Indication Lamps
On/Off : Lights up during the system operation.
Filter Sign : Lights up after 2400 hours from the time of first operating unit.
Timer : Lights up during Timer operation.
Defrost Mode : Lights up during Defrost Mode or Hot Start operation. (Heat pump model only)
Forced operation : To operate the unit when the remote control can't be used for any reason.
<![endif]>ENGLISH
<![endif]>ENGLISH
10 PRODUCT INTRODUCTION
Wireless Remote Controller
|
|
1 |
VANE ANGLE Button |
|
|
|
|
Used to set each vane angle. |
|
|
|
2 |
FUNCTION SETTING Button |
|
|
|
|
Used to set or clear Auto Clean, Smart |
|
|
|
|
Clean, Electric heater or Individual vane |
|
|
|
|
angle control. |
|
1 |
|
3 |
ON/OFF Button |
|
|
|
Used to turn on/off the unit. |
||
2 |
10 |
4 |
JET COOL Button |
|
|
11 |
|
Speed cooling operates super high fan |
|
3 |
12 |
5 |
speed. |
|
|
|
LEFT/RIGHT AIRFLOW Button (OPTIONAL) |
||
4 |
13 |
|
Used to set the desired left/right(horizontal) |
|
|
airflow direction. |
|||
5 |
|
|
||
|
6 |
UP/DOWN AIRFLOW Button |
||
6 |
14 |
|||
|
Used to stop or start louver movement and |
|||
7 |
|
|
||
15 |
|
set the desired up/down airflow direction. |
||
8 |
7 |
ON TIMER Button |
||
|
16 |
|||
|
|
|
Used to set the time of starting operation. |
|
9 |
17 |
8 |
SLEEP TIMER Button |
|
|
|
|
Used to set the time of sleeping operation. |
|
|
|
9 |
SET / CLEAR Button |
|
|
|
|
Used to set/clear the timer. |
|
Operation Mode |
|
|
Used to set the current time(if it input for |
|
|
|
3sec.) |
Cooling Mode |
10 PLASMA Button (OPTIONAL) |
Used to start or stop the plasma-purification |
|
|
function. |
Auto Mode or Auto Changeover
Dehumidification mode
Heating Mode
Fan Mode
• Cooling Model(), Heat Pump Model(
)
11ROOM TEMPERATURE SETTING Button Used to select the room temperature.
12OPERATION MODE SELECTION Button Used to select the operation mode.
13INDOOR FAN SPEED SELECTION Button Used to select fan speed in four steps low, medium, high and chaos.
14ROOM TEMPERATURE CHECKING Button Used to check the room temperature.
15OFF TIMER Button
Used to set the time of stopping operation.
16TIMER SETTING(Up/Down)/LIGHT Button Used to set the timer.
Used to adjust the brightness.(if it is not time adjust mode)
17RESET Button
Used to reset the remote controller.
OPERATING INSTRUCTION 11
OPERATING INSTRUCTION
How to insert the Batteries
1Remove the battery cover by pulling it according to the arrow direction.
2Insert new batteries making sure that the
(+) and (-) of battery are installed correctly.
3Reattach the cover by sliding it back into position.
!NOTE
•Always use/replace both batteries of same type.
•If the system is not to be used for a long time, remove the batteries to save their working life.
•If the display screen of remote controller starts, fading replace both of the batteries.
Wireless Remote Controller
Maintenance
1Choose a suitable place where its safe & easy to reach.
2Fix the holder to wall etc with the supplied screws firmly.
3Slide the remote controller inside the holder.
!NOTE
•Remote controller should never be exposed to direct sunlight.
•Signal transmitter & receiver should always be clean for proper communication. Use a soft cloth to clean them.
•In case some other appliances also get operated with remote control, change their position or consult your serviceman.
Operating Method
1 The signal receiver is inside the unit.
2Aim the remote controller towards the unit to operate it. There should not be any blockage in between.
<![endif]>ENGLISH
<![endif]>ENGLISH
12 OWNER'S INSTRUCTION
OWNER'S INSTRUCTION
Cooling Mode - Standard Operation
1 Press the ON/OFF button.
The unit will respond with beep sound.
2 Press MODE button to select Cooling Mode.
3 Set the desired temperature by pressing TEMP button.
Press ROOM TEMPERATURE CHECKING button to check the room temperature. When setting the desired temperature is higher than room temperature, cooling wind isn’t blow out.
To raise the temperature
To lower the temperature
* Setting Temp. Range : 18~30 °C(64~86 °F)
Cooling Mode - Power Cooling
1 Press the ON/OFF button.
The unit will respond with beep sound.
2 Press MODE button to select Cooling Mode.
3 |
Press the JET COOL button. The unit will operate in |
|
|
||
|
super high fan speed in cooling mode. |
|
|
* Wall mounted models operate power cooling mode |
|
4 |
for 30 minutes. |
|
To cancel the Power cooling Mode press the Jet Cool button or the |
||
|
||
|
fan button or the room temperature setting button again and the |
|
|
unit will operate in high fan speed in cooling mode. |
or |
or |
OWNER'S INSTRUCTION 13
Cooling Mode - Comfort Cooling
This function is automatically control the cooling strength to maintain the pleasant feeling without turning off the product after the indoor temperature reached the desired temperature.
1 |
Press the ON/OFF button. |
The unit will respond with beep sound. |
2 Press MODE button to select Cooling Mode.
3 Press FUNC. Button repeatedly until comfort cooling icon displayed.
4 Press SET/CLEAR button for setting.
<![endif]>ENGLISH
<![endif]>ENGLISH
14 OWNER'S INSTRUCTION
Heating Mode
This Function is only for H/P model.
1
2
Press the ON/OFF button.
The unit will respond with beep sound.
Press MODE button to select Heating Mode.
|
|
3 |
Set the desired temperature by pressing TEMP button. |
|||
|
|
|
Press ROOM TEMPERATURE CHECKING button to check the |
|||
|
|
|
room temperature. |
|
||
|
|
|
When setting the desired temperature is lower than room |
|||
|
|
|
temperature, heating wind isn’t blow out. |
|||
|
|
|
|
|
To raise the temperature |
* Setting Temp. Range in |
|
|
|
|
|
||
|
|
|
||||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Heating Mode : |
|
|
|
|
|
To lower the temperature |
16~30 °C (60 °F~86 °F) |
|
|
|
|
|
4 Set the fan speed again. You can select the fan speed in four steps–low, medium, high, or chaos. Each time the button is pressed, the fan speed mode is shifted.
OWNER'S INSTRUCTION 15
Dehumidification Mode
1 |
Press the ON/OFF button. |
The unit will respond with beep sound. |
2 Press MODE button to select Dehumidification Mode.
3 Set the fan speed. You can select the fan speed in five steps - super low,low, medium, high, or chaos.Each time the button is pressed, the fan speed mode is shifted.
<![endif]>ENGLISH
<![endif]>ENGLISH
16 OWNER'S INSTRUCTION
Fan Mode
1 |
Press the ON/OFF button. |
The unit will respond with beep sound. |
2 Press MODE button to select Fan Mode.
3 Set the fan speed again. You can select the fan speed in five steps–super low,low, medium, high, orchaos. Each time the button is pressed,
the fan speed mode is shifted.
!NOTE
••Naattuurraall Wiinnd by thhe chhaaoos Looggiic
For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to chaos mode. In this mode, the wind blows like natural breeze by automatically changing fan speed according to the chaos logic.
••Duurriinng Faan Moodde
The outdoor compressor doesn't work.
Have a function to circulate the indoor as it sends out the air that doesn't have much temperature difference with indoor.
OWNER'S INSTRUCTION 17
Auto Operation Mode
1 Press the ON/OFF button.
The unit will respond with beep sound.
2 Press MODE button to select Auto Operation Mode.
3 Set the desired temperature.
<For Cooling only Model>
The temperature and fan speed are automatically set by the electronic controls based on the actual room temperature.
If you feel hot or cold, press TEMPERATURE SETTING buttons for more cooling or heating effect.
You cannot switch the indoor fan speed. It has already been set by the Auto Operation Mode rule.
To raise the temperature |
* Please select the code |
|
|
depend on your feeling. |
|
To lower the temperature |
Code |
Feel |
|
2 |
Cold |
|
1 |
Slightly cool |
|
0 |
Neutral |
|
-1 |
Slightly warm |
|
-2 |
Warm |
<![endif]>ENGLISH
! NOTE
During Auto Operation Mode
-If the system is not operating as desired, manually switch to another mode. The system will not automatically switch from the cooling mode to the heating mode, or from heating to cooling, then you must set the mode and the desired temperature again.
<![endif]>ENGLISH
18 OWNER'S INSTRUCTION
Auto Changeover Mode
1 |
Press the ON/OFF button. The unit will re- |
spond with beep sound. |
|
Press MODE button to select Auto |
|
2 Changeover Mode. |
|
|
3 |
Set the desired room temperature. |
To raise the temperature |
* Setting Temp. Range in Auto |
|
|
|
Changeover Mode : 18~30 °C |
To lower the temperature |
|
(64~86 °F) |
|
4 You can select the fan speed in five steps– super low,low, medium, high, orchaos. Each time the button is pressed,the fan speed mode is shifted.
! NOTE
During Auto changeover Mode
The air conditioner changes the operation mode automatically to keep indoor temperature. When room temperature vary over ±2 °C(4 °F) with respect to setting temperature, air conditioner keeps the room temperature within ±2 °C(4 °F) with respect to setting temperature by auto changeover mode.
<![endif]>ENGLISH
OWNER'S INSTRUCTION 19
Auto Changeover Mode - Setting the Mode Change Temperature
This Function is to set the operating mode of the Auto Changeover Mode.
1 In Auto Changeover Mode, Press FUNCTION button to select Setting the Mode Change Temperature.
2 Press the TEMPERATURE SETTING button to set desired Mode Change Temperature. (Default value is 2 °C(4 °F).)
To raise the temperature
|
* Mode Change Temp. Range : |
To lower the temperature |
1~7 °C(2~14 °F) |
3 Complete the setting by pressing SET/CLEAR button.
! NOTE
The Mode Change Temperature is the difference of temperature when from cooling mode to heating mode or from heating mode to cooling mode.
Ex) When setting temperature is 25 °C(76 °F) and room temperature is 20 °C(68 °F), then operating mode is heating. If you set the mode change temperature to 2 °C(4 °F), when the room temperature up to 27 °C(25 °C + 2 °C)(80 °F(76 °F + 4 °F)), the unit start cooling operation.
<![endif]>ENGLISH
|
20 |
OWNER'S INSTRUCTION |
|
|
|
<![if ! IE]> <![endif]>ENGLISH |
Airflow Setting |
|
|
||
|
Up/Down Airflow Direction Control (Optional) |
|
|
||
|
The up/down airflow (Vertical Airflow) can be adjusted by using the remote controller. |
|
|
1 Press the ON/OFF button to start the unit. |
2Press up/down airflow button and the louvers will swing up and down.
Press the up/down airflow button again to set the vertical louver at the desired airflow direction.
! NOTE
•If you press the UP/DOWN AIRFLOW button, the horizontal airflow direction is changed automatically based on the Auto Swing algorithm to distribute the air in the room evenly and at the same time to make the human body feel more comfortable, as if enjoying a natural breeze.
•Always use the remote controller to adjust the up/down airflow direction. Manually moving
the vertical airflow direction louver by hand, could damage the air conditioner.
•When the unit is shut off, the up/down airflow direction louver will close the air outlet vent of the system.
Celsius/Fahrenheit Switching
-Press the °C/°F SWITCH button to change from Celsius to Fahrenheit or from Fahrenheit to Celsius.
-Whenever press TEMPERATURE SETTING button in Fahrenheit mode, the temperature
will increase/drop 1 °F.
<![endif]>ENGLISH
<![endif]>ENGLISH
OWNER'S INSTRUCTION 21
Temperature Setting/Room Temperature checking
We can simply adjust the desired temperature
- Press the buttons to adjust the desired temperature
: Increase Temp. per one time pressing
: Decrease Temp. per one time pressing
Room temp: Indicate the current room temperature
Set temp: Indicate the temperature that user want to set
<Cooling Mode>
The cooling mode doesn't work if desired temperature is higher than room temperature Please lower the desired temperature
<Heating Mode>
The heating mode doesn't work if desired temperature is lower than room temperature Please increase the desired temperature
Whenever press ROOM TEMPERATURE button, the room temperature will be displayed within 5 seconds.
After 5 seconds, it turns to display the desired temperature.
Because of location of remote controller, the real room temperature and the this displayed value can be different.
Press ROOM TEMPERATURE button for 5 seconds, temperature unit change Celsius to Fahrenheit or Fahrenheit to Celsius.
<![endif]>ENGLISH
<![endif]>ENGLISH
22 SUB FUNCTION
SUB FUNCTION
Plasma Purification(Optional)
1 Press the ON/OFF button.
The unit will respond with beep sound.
2 Press the PLASMA button. Plasma Purification will start when the button is pressed and stop when the button is pressed again.
PLASMA Purification only If you press the PLASMA button, Plasma Purification operates.
• Plasma filter is a technology developed by LG to get rid of microscopic contaminants in the intake air generating a plasma of high charge electrons. This plasma kills and destroys the contaminants completely to provide clean and hygienic air.
• This function can be used in any operation mode and any fan speed can be used while plasma filter is functioning.
Auto Clean (Optional)
This function operate when the unit is turned off.
1 Press the FUNCTION SETTING button 1 time. Auto Clean symbol will blink.
2 Press the SET/CLEAR button to reserve or cancel the Auto Clean function.
If the Auto Clean function is reserved, whenever the unit is turned off, the indoor fan is still running for about 30 minutes internally without cooling or dehumidification operation. Also the louver is closed.
This dries up any remains of moisture & cleans the unit internally.
<![endif]>ENGLISH
<![endif]>ENGLISH
SUB FUNCTION 23
Smart Clean (Optional)
The Smart Clean function can be used by setting to manual or automatic.
Auto Smart Clean operation
If the accumulated operation time of the product exceeds 30 hours, the Smart Clean automatically starts when the unit is turned off.
1 Press the FUNCTION SETTING button 2 times. Smart Clean symbol will blink.
2 Press the SET/CLEAR button to reserve or cancel the Smart Clean function.
You can set/clear with out on or off.
<![endif]>ENGLISH
Manual Smart Clean operation
1 When the unit stop, press the FUNCTION button to select Smart Clean.
Smart Clean symbol blinks, then press SET/CLEAR button.
2 To stop Manual Smart Clean operation, press the FUNCTION button to select Smart clean and press SET/CLEAR button.
The brush clean a dust from the filter by moving from left to right or from right to left on the filter. The sucked dust is collected into the dust box.
The operating process of Smart Clean is different from the product type.
<![endif]>ENGLISH
24 SUB FUNCTION
Individual vane angle control (Optional)
It is the function that can control 4 vane angles individually in the ceiling type 4Way cassette product group.
1 Press the VANE ANGLE button, Individual vane angle control symbol will blink.
When vane angle control button is pressed, it repeats in the order of No.1 vane → No.2 vane → No.3 vane → No.4 vane → vane angle control mode is released.
No1. Vane |
No2. Vane |
No3. Vane |
Release |
No4. Vane |
2 Set each vane angle by pressing TEMPERATURE SETTING buttons.
•Every time VANE ANGLE button is pressed, corresponding vane angle and set values are displayed.
•When temperature setting button is pressed, the display window appears asof the figure in the right, and the angle can be set to 1 ~6.
1st stage |
2nd stage |
3rd stage |
6th stage |
5th stage |
4th stage |
3 Complete the setting by pressing SET/CLEAR button. Vane angle control mode is released.
•If you press the VANE ANGLE button 3sec. all vanes are set to standard angle.
•There may be differences between wireless remote controller up/down/left/right buttons and the wind discharge port directions.
•Set desired angle with checking the vane angle movement of the product.
•The individual vane control function is an additional function of a product, and it may not work in some products.
<![endif]>ENGLISH
TIMER 25
TIMER
Setting the Current Time
1 Press the SET / CLEAN button for 3 seconds.
2 Press TIME SETTING buttons until the desired time is set. (If you press down the button for a long time, it will change quickly in the units of 10 min.)
3 Press the SET / CLEAR button.
! NOTE
Check the indicator for A.M. and P.M.
Sleep Timer Setting
1 Press the TIMER button to turn timer on or off.
Timer Sleep
2 Press TIME SETTING buttons until the desired time is set. (7 hours is the maximum setting)
3 Press the SET / CLEAR button.
<![endif]>ENGLISH
On Timer Setting
1 Press the ON button to turn timer on or off.
Timer ON
2 Press TIME SETTING buttons until the desired time is set.
3 Press the SET / CLEAR button.
<![endif]>ENGLISH
26 TIMER
Off Timer Setting
1 Press the OFF button to turn timer on or off.
Timer OFF
2 Press TIME SETTING buttons until the desired time is set.
3 Press the SET / CLEAR button.
To cancel the Timer Setting
-If you wish to cancel all timer setting, press the CLEAR ALL button.
-If you wish to cancel each timer setting, press the
each timer button to turn timer sleep or on or off as you want. And then press the SET/CLEAR button aiming the remote controller at the signal receptor.
(The timer lamp on the air conditioner and the display will go off.)
MAINTENANCE AND SERVICE 27
MAINTENANCE AND SERVICE
Indoor Unit |
- Remove the Air filters. |
Grille, Case and Remote Control
-Turn the system off before cleanining, To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives.
! NOTE
Supply power must be disconnected before cleaning the indoor unit.
Air Filters
The air filters behind the front grille should be checked and cleaned once every 2 weeks or more often if neccessary.
-Never use any of the followings:
Water hotter than 40 °C.
Could cause deformation and or discoloration.
Volatile substances.
Could damage the surfaces of the air conditioner.
|
SI |
|
|
|
NNER |
SCOURIN |
|
|
|
||
Benzene |
|
CL |
BARGE |
|
|
Take hold of the tab and pull slightly forward to remove the filter.
! CAUTION
When the air filter is to be removed, do not touch the metal parts of the indoor unit.
It may cause an injury.
-Clean dirt from the air filter using a vacuum cleaner or washing with water.
If dirt is conspicuous, wash with a neutral detergent in lukewarm water.
If hot water (40 °C or more) is used, it may be deformed.
-After washing with water, dry well in the shade.
Do not expose the air filter to direct sunlight or heat from a fire when drying it.
-Install the air filter.
Louver
Air outlet vent
Air filters (behind inlet grille)
Air inlet vent
(inlet grille)
<![endif]>ENGLISH
<![endif]>ENGLISH
28 MAINTENANCE AND SERVICE
Operation Tips!
Do not overcool the room. |
Keep blinds or curtains closed. |
Keep the room temperature |
This is not good for the health |
Do not let direct sunshine |
uniform. |
|
||
and wastes electricity. |
enter the room when the air |
Adjust the vertical and hori- |
|
conditioner is in operation. |
zontal airflow direction to en- |
|
|
sure a uniform temperature in |
|
|
the room. |
Make sure that the doors |
Clean the air filter regularly. |
Ventilate the room occasion- |
and w indow s are shut tight. |
Blockages in the air filter re- |
ally. |
|
|
|
Avoid opening doors and win- |
duce the airflow and lower |
Since windows are kept |
dows as much as possible to |
cooling and dehumidifying ef- |
closed, it is a good idea to |
keep the cool air in the room. |
fects. Clean at least once |
open them and ventilate the |
|
every two weeks. |
room now and then. |
When the air conditioner is not
going....
When air conditioner is not going to be used for a long time.
-Operate the air conditioner at the following settings for 2 to 3 hours.
Type of operation: Fan operation mode. (Refer to page “Fan Mode”.)
This will dry out the internal mechanisms. - Turn off the breaker.
! CAUTION
Turn off the breaker when the air conditioner is not going to be used for a long time.
Dirt may collect and may cause a fire.
-Remove the batteries from the Remote Controller.
Disposal of Waste Batteries/Accumulators
Helpful information
The air filters and your electiric bill.
If the air filters become clogged with dust, the cooling capacity will drop, and 6% of the electricity used to operate the air conditioner will be wasted.
When the air conditioner is to be used again.
-Clean the air filter and install it in the indoor unit. (Refer to page “MAINTENANCE AND SERVICE”.)
-Check that the air inlet and outlet of the indoor/outdoor unit are not blocked.
-Check that the ground wire is connected correctly. It may be connect to the indoor unit side.
•This symbol may be combined with chemical symbols for mercury (Hg), cadmium (Cd) or lead (Pb) if the battery contains more than 0.0005 % of mercury, 0.002 % of cadmium or 0.004 % of lead.
•All batteries/accumulators should be disposed separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
•The correct disposal of your old batteries/accumulators will help to prevent potential negative consequences for the environment, animal and human health.
•For more detailed information about disposal of your old batteries/accumulators, please contact your city office, waste disposal service or the shop where you purchased the product.
MAINTENANCE AND SERVICE 29
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist, please contact your dealer.
The air conditioner |
The room has a pecu- |
It seems that conden- |
Air conditioner does |
|
does not operate. |
liar odor. |
sation is leaking from |
not operate for about |
|
- Have you made a |
- Check that this is not |
the air conditioner. |
3 minutes when |
|
mistake in timer op- |
a damp smell ex- |
- Condensation occurs |
restart. |
|
eration? |
uded by the walls, |
when the airflow |
- This is the protector |
|
- Has the fuse blown |
carpet, furniture or |
from the air condi- |
of the mechanism. |
|
cloth items in the |
tioner cools the |
|
||
or has the circuit |
- Wait about three |
|||
room. |
warm room air. |
|||
breaker been |
minutes and opera- |
|||
|
|
|||
tripped? |
|
|
tion will begin. |
|
|
|
|
|
|
Does not cool or heat |
The air conditioner op- |
Crack sound is heard. |
Remote control dis- |
|
effectively. |
eration is noisy. |
- This sound is gener- |
play is faint, or no dis- |
|
|
|
play at all. |
||
- Is the air filter dirty? |
- For a noise that |
ated by the expan- |
||
|
||||
See air filter cleaning |
sounds like water |
sion/ constriction of |
- Are the batteries de- |
|
instructions. |
flowing. |
the front panel, etc. |
pleted? |
|
- The room may have |
* This is the sound |
due to changes of |
- Are the batteries in- |
|
temperature. |
||||
been very hot when |
of freon flowing in- |
serted in the oppo- |
||
|
||||
the room air condi- |
side the air condi- |
|
site (+) and (-) |
|
tioner was first |
tioner unit. |
|
directions? |
|
turned on. Allow |
- For a noise that |
|
|
|
|
|
|||
time for it to cool |
Filter sign lamp (LED) |
The error code is oc- |
||
sounds like the com- |
||||
down. |
pressed air releasing |
is ON. |
curred after lightning |
|
- Has the temperature |
into atmosphere. |
- Cleaning the filter, |
struck |
|
been set incorrectly? |
- This is the sound of |
press the Timer but- |
- This product has been |
|
- Are the indoor unit's |
the dehumidifying |
ton and button of |
applied to the over |
|
air inlet or outlet |
water being |
wired remote con- |
current protection cir- |
|
vents obstructed? |
processed inside the |
troller at the same |
cuit. |
|
|
air conditioning unit. |
time for 3 sec. |
Error can occur, but it |
|
|
|
|
is normal behavior. |
|
|
|
|
After few minutes, It |
|
|
|
|
will operate normally. |
|
|
|
|
|
Call the service immediately in the following situations
-Anything abnormal such as burning smell, loud noise etc. happen. Stop the unit and turn the breaker off. Never try to repair by yourself or restart the system in such cases.
-Main power cable is too hot or damaged.
-Error code is generated by self diagnosis.
-Water leaks from indoor unit even if the humidity is low.
-Any switch, breaker (safety, earth) or fuse fails to work properly
<![endif]>ENGLISH
User must carry routine checkup & cleaning to avoid unit’s poor performance. In case of special situation, the job must be carried out by service person only.
30
<![if ! IE]><![endif]>ENGLISH