<![endif]>~ ESPANOL ENGLISH
OWNER’S MANUAL
DRYER
Please read this manual carefully before operating your dryer and retain it for future reference.
TDN1653S
TDN1653ES
TDN1653GS
TDN1753GS
P/No. : MFL62512823
IMPORTANT SAFETY INSTRUCTIONS |
|
What to Do if You Smell Gas................................... |
3 |
Basic Safety Precautions........................................ |
4 |
California safe drinking water and toxic |
|
enforcement act..................................................... |
4 |
Grounding Instructions........................................... |
5 |
Safety Instructions for Installation....................... |
5, 6 |
Safety Instructions for Steam Functions................. |
6 |
Safety Instructions for Connecting Electricity ........ |
7 |
PARTS AND FEATURES |
|
Special Features..................................................... |
8 |
Key Parts and Components.................................... |
9 |
INSTALLATION INSTRUCTIONS |
|
IMPORTANT: Read all installation instructions |
|
completely before installing and operating your |
|
dryer! .................................................................... |
10 |
Choose the Proper Location................................. |
10 |
Clearances............................................................ |
10 |
Installation With Optional |
|
Pedestal Base or Stacking Kit.............................. |
11 |
Optional Accessories .......................................... |
11 |
Leveling the Dryer................................................. |
12 |
Reversing the Door Swing.................................... |
12 |
Changing the Dryer Vent Location........................ |
13 |
Venting the Dryer............................................. |
14, 15 |
Connecting Gas Dryers................................... |
16, 17 |
Connecting Electric Dryers............................. |
18–22 |
Special Requirements for Manufactured |
|
or Mobile Homes................................................... |
23 |
Final Installation Check ........................................ |
23 |
Duct Condition Testing.......................................... |
24 |
HOW TO USE |
|
Sorting Loads........................................................ |
25 |
Loading the Dryer................................................. |
25 |
Check the Lint Filter Before Every Load............... |
25 |
Control Panel Features......................................... |
26 |
Cycle Guide........................................................... |
27 |
The Display........................................................... |
28 |
Operating the Dryer............................................... |
29 |
Cycle Setting Buttons........................................... |
30 |
Cycle Option Buttons ........................................... |
30 |
Special Functions.................................................. |
31 |
Custom Program................................................... |
32 |
Before Using the Steam Functions....................... |
32 |
Steam Functions............................................. |
33, 34 |
Steam Cycle Guide............................................... |
34 |
user maintenance instructions |
|
Regular Cleaning................................................... |
35 |
TROUBLESHOOTING |
|
Before Calling for Service............................... |
36–38 |
THANK YOU!
Congratulations on your purchase
and welcome to the LG family. Your
new LG Dryer combines the most
advanced drying sensor technology
with simple operation and high
efficiency. By following the operating and care instructions
in this manual, your dryer will
provide you with many years of
reliable service.
OPTIONAL ACCESSORIES/SPECIFICATIONS
Optional Accessories............................................ |
39 |
Pedestal Installation........................................ |
40, 41 |
Stacking Kit Installation.................................. |
42, 43 |
Key Dimensions and Specifications...................... |
43 |
2
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:
wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.
wWARNING: You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance or any other appliances.
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•Save these instructions.
WHAT TO DO IF YOU SMELL GAS:
1.Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2.Do not touch any electrical switches. Do not use any phone in your building.
3.Clear the room, building, or area of all occupants.
4.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.
5.If you cannot reach your gas supplier, call the fire department.
<![endif]>ENGLISH
3
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
BASIC SAFETY PRECAUTIONS
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Read all instructions before using the dryer.
•Before use, the dryer must be properly installed as described in this manual.
•Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
•Do not reach into the dryer if the drum or any other part is moving.
•Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.
•Do not tamper with controls.
•Before the dryer is removed from service or discarded, remove the door to the drying compartment.
•Do not allow children to play on or in the dryer.
Close supervision of children is necessary when the dryer is used near children.
•Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
•Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
•Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.
•The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.
•Do not install or store the dryer where it will be exposed to the weather.
•Always check the inside of the dryer for foreign objects.
•Clean lint screen before or after each load.
California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the state to cause cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.
4
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be equipped with a cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
wWARNING— Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance must be connected to a grounded metal, permanent wiring system or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the appliance.
Electrical shock can result if the dryer is not properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Properly ground dryer to conform with all governing codes and ordinances. Follow details in the installation instructions. Electrical shock can result if the dryer is not properly grounded.
•Before use, the dryer must be properly installed as described in this manual.
Electrical shock can result if the dryer is not properly grounded.
•Install and store the dryer where it will not be exposed to temperatures below freezing or exposed to the weather.
•All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this Owner’s Guide. Use only authorized factory parts. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.
•To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.
• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload. Improper power circuit can melt, creating electrical shock and/or fire hazard.
• Remove all packing items and dispose of all shipping materials properly. Failure to do so can result in death, explosion, fire, or burns.
• Place dryer at least 18 in. above the floor for a garage installation. Failure to do so can result in death, explosion, fire, or burns.
• Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.
• Do not install nearby heat item. Such as stove, cooking oven. Failure to do so can cause deform, smoke and fire.
• Do not place candle and cigarettes on top of the product. Failure to do so can cause deform, smoke and fire.
• Remove all protective vinyl film from the product. Failure to do so can cause deform,
smoke and fire.
5
<![endif]>ENGLISH
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
•Gas dryers MUST be exhausted to the outside. Failure to follow these instructions can result in fire or death.
•The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An accumulation of
lint in any area of the home can create a health and fire hazard.
•Use only rigid metal or flexible metal 4-in. diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork can cause a fire. Punctured ductwork can cause a fire if it collapses or becomes otherwise restricted in use or during installation.
•Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 in. (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible.
Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semi rigid metal ducting is recommended for use between the dryer and the wall. In special installations
when it is impossible to make a connection with the above recommendations, a ULlisted flexible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect drying time. Failure to follow these instructions can result in fire or death.
•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in fire or death.
SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not open the dryer door during steam cycles. Failure to follow these instructions can result in a burn hazard.
•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
Failure to follow these instructions can result in fire or death.
•Do not fill the steam feeder with gasoline, dry-cleaning solvents, or other flammable or explosive substances. Failure to follow these instructions can result in fire or death.
•Do not touch the steam nozzle in the drum during or after the steam cycle. Failure to follow these instructions can result in a burn hazard.
•Do not fill the steam feeder with hot water (over 86°F/30°C). Failure to follow these instructions can result in a burn hazard.
6
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the ground prong from the power cord. To prevent personal injury or damage to the dryer, the electrical power cord must be plugged into a properly grounded outlet.
•For personal safety, this dryer must be properly grounded. Failure to do so can result in electrical shock or injury.
•Refer to the installation instructions in this manual for specific electrical requirements for your model. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.
•This dryer must be plugged into a properly grounded outlet. Electrical shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.
•The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
•Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. The power cord can be damaged, resulting in a risk of fire and electrical shock.
•Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt, creating electrical shock and/or fire hazard.
•When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord. This will prevent injury and prevent damage to the dryer from fire and electrical shock.
<![endif]>ENGLISH
SAVE THESE INSTRUCTIONS
7
SPECIAL FEATURES
1Easy-to-USE Control Panel
Rotate the Cycle Selector Knob to select the desired dry cycle. Add cycle options or adjust settings with the touch of a button.
2EASY-ACCESS REVERSIBLE DOOR
Wide-opening door provides easy access for loading and unloading. Door swing can be reversed to adjust for installation location.
3Ultra-Capacity Stainless Steel Drum with DRUM Light
The ultra-large stainless steel drum offers superior durability. The drum is equipped with a yellow light that illuminates when the dryer door is open and turns off when the door is closed.
4HELPFUL STEAM FUNCTIONS
LG’s new steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static, and make ironing easier. Simply select the STEAMFRESH™ cycle, or you can add a Steam option to selected cycles.
5FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The FLOW SENSE™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. This improve operating efficiency and help minimize service calls, saving you money.
4 |
1 |
5 |
|
2
3
8
KEY PARTS AND COMPONENTS
In addition to the special features and components outlined in the Special Features section, there are several other important components that are referenced in this manual.
1FRONT-MOUNT LINT FILTER
Front-mounted lint filter allows for easy access and cleaning after every load.
2Leveling Feet
Four leveling feet (two in the front, and two in the back) adjust to improve dryer stability on uneven floors.
3Drying Rack
Use the drying rack with the RACK DRY cycle option. The drying rack allows items, such as sweaters, delicates, and gym shoes, to be placed in a flat position for drying.
<![endif]>ENGLISH
1
2
Power Cord Location |
Terminal Block |
(Gas Models) |
Access Panel |
|
(Electric Models) |
Gas |
Exhaust Duct |
Connection |
Outlet |
Location |
|
(Gas Models) |
|
|
Rear of Dryer |
Included Accessories
3
Drying Rack
9
IMPORTANT: Read all installation instructions completely before installing and operating your dryer!
It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.
CHOOSE THE PROPER LOCATION
•Store and install the dryer where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions.
•Choose a location with a solid, level floor.
•If the dryer is being installed in a garage, place the dryer at least 18 in. (45.7 cm) above the floor.
•Properly ground dryer to conform with all governing codes and ordinances.
•To reduce the risk of electric shock, do not install the dryer in damp or wet locations.
•If you are installing your dryer in a manufactured or mobile home, please refer to the section
Special Requirements for Manufactured or Mobile Homes.
CLEARANCES
22.5” |
18” |
|
(57.2 cm) |
|
|
(45.7 cm) |
|
|
|
|
|
4” |
30” |
4” |
(10 cm) |
(76.2 cm) |
(10 cm) |
|
51” |
|
|
(130 cm) |
|
•Most installations require a minimum 5½ in.
(14 cm) clearance behind the dryer for the exhaust ducting.
•Allow minimum clearances of at least 1 in.
(2.54 cm) on the sides and back to minimize vibration and noise.
•Allowing additional clearance for installation and servicing is recommended.
•Be sure to allow for wall, door, or floor moldings that may increase the required clearances.
•Allow at least 24 in. (61 cm) in front of the dryer to open the door.
Closet Door Vent
Requirements
Additional Instructions for closet installations:
•The closet door must allow for sufficient airflow.
Refer to the diagram above for minimum vent opening requirements. A louvered door is also acceptable.
•Make sure that there is at least 18 in. (45.7 cm) of clearance above the dryer.
10
INSTALLATION WITH OPTIONAL PEDESTAL BASE OR STACKING KIT
IMPORTANT: If you are installing your dryer using an optional pedestal base or stacking kit, please refer to Optional Accessories in this manual or to the instructions for your pedestal or stacking kit before proceeding with the installation.
Required Dimensions for Installation With Pedestal
30” |
4” |
(76.2 cm) |
(10 cm) |
Required Dimensions for Installation
With Stacking Kit
|
|
771⁄2” |
|
|
(190.5 cm) |
1” |
27” |
1” |
(2.54 cm) |
(68.6 cm) |
(2.54 cm) |
OPTIONAL ACCESSORIES
For these and other LG products, contact your local LG dealer, or visit our Web site at www.lg.com
<![endif]>ENGLISH
Pedestal (sold separately) |
Stacking Kit (sold separately) |
11
LEVELING THE DRYER
wWARNING
•Wear gloves during installation.
•Failure to follow these instructions can result in injury.
To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.
NOTE: Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.
Level
Leveling Feet
1Position the dryer in the final location. Place a level across the top of the dryer.
•All four leveling feet must rest solidly on the floor. Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal, you must use the leveling feet on the pedestal to level the dryer. The dryer leveling feet should be fully retracted.
2Use an adjustable wrench to turn the leveling feet. Turn clockwise to raise the dryer or counterclockwise to lower it. Raise or lower the leveling feet until dryer is level from
side to side and front to back.
Make sure that all 4 leveling feet are in firm contact with the floor.
REVERSING THE DOOR SWING
The swing of the dryer door can be reversed to fit your installation location.
Door
Latch
|
Hinge |
Latch Screws |
Screws |
1Open the dryer door. Using a Phillips screwdriver, remove the 2 screws that secure the door hinge to the dryer door opening. Remove the 4 screws from the latch side of the dryer door opening, and remove the door latch.
12
Latch
Screws
Hinge
Screws
2Turn the door around so the hinge is reversed, and reattach the door using the 2 screws previously removed. Reinstall the door latch and the 4 screws.
Test the door swing to make sure the door moves freely and latches securely.
CHANGING THE DRYER VENT LOCATION
wWARNING
•Use a heavy metal vent.
•Do not use plastic or thin foil duct.
•Clean old ducts before installing this dryer.
•Wear gloves during installation.
•Failure to follow these instructions can result in death or fire.
Your new dryer is shipped to vent to the rear. It can also be configured to vent to the bottom or side (right-side venting is not available on gas models).
An adapter kit, part number 383EEL9001B, may be purchased from your LG retailer. This kit contains the necessary duct components to change the dryer vent location.
Retaining
Screw
Rear
Exhaust Duct
1Remove the rear exhaust duct retaining screw. Pull out the exhaust duct.
OPTION 1: Side Venting
Adapter
Duct
Bracket
Knockout
2Press the tabs on the knockout and carefully remove the knockout for the desired vent opening (right-side venting is not available on gas models). Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.
Cover
Plate
Elbow
11/2"
(3.8 cm)
3Preassemble a 4-in. (10 cm) elbow to the next 4-in. (10 cm) duct section, and secure all joints with duct tape. Be sure that the male end of the elbow faces AWAY from the dryer.
Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure in place with duct tape.
Be sure that the male end of the duct protrudes 1½ in. (3.8 cm) to connect the remaining ductwork.
Attach cover plate to the back of the dryer with included screw.
OPTION 2: Bottom Venting
Adapter
Duct
Bracket
2Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.
Cover
Plate
Elbow
3Insert the 4-in. (10 cm) elbow through the rear opening and press it onto the adapter duct. Be sure that the male end of the elbow faces down through hole in the bottom of the dryer. Secure in place with duct tape.
Attach the cover plate to the back of the dryer with included screw.
13
<![endif]>ENGLISH
VENTING THE DRYER
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not crush or collapse ductwork. Failure to follow these instructions can result in fire or death.
•Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions can result in fire or death.
•If connecting to existing ductwork, make sure it is suitable and clean before installing the dryer. Failure to follow these instructions can result in fire or death.
•Venting must conform to local building codes. Failure to follow these instructions can result in fire or death.
•Gas dryers MUST exhaust to the outdoors.
Failure to follow these instructions can result in fire or death.
•Use only 4 in. (10 cm) rigid or flexible metal ductwork inside the dryer cabinet and
for venting outside. Failure to follow these instructions can result in fire or death.
•To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to follow these instructions can result in fire
or death.
•To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting.
Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 in. (10 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semirigid metal ducting is recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a UL-listed flexible metal transition duct may be used
between the dryer and wall connection only. The use of this ducting will affect drying
time. Failure to follow these instructions can result in fire or death.
•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. Failure to follow these
instructions can result in fire or death.
•To maximize operating results, please observe the duct length limitations noted in the chart on page 15. Failure to follow these
instructions can result in fire or death.
•Ductwork is not provided with the dryer. You should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these
instructions can result in fire or death.
•The Total length of flexible metal duct shall not exceed 8 ft.(2.4m)
•In Canada, that only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer shall be used. In the United States, that only
those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A, shall be used.
14
VENTING THE DRYER (cont.) |
|
<![if ! IE]> <![endif]>ENGLISH |
||
Ductwork |
|
|
|
|
Wall Cap Type |
Number of 90° Elbows |
Max. Length of 4-In. Dia. |
||
Rigid Metal Duct |
|
|||
|
|
|
|
|
Recommended |
0 |
65 ft. (19.8 m) |
|
|
1 |
55 ft. (16.8 m) |
|
||
|
|
|
||
|
|
2 |
47 ft. (13.7 m) |
|
4" |
4" |
3 |
36 ft. (11.0 m) |
|
(10.2 cm) |
(10.2 cm) |
4 |
28 ft. (8.5 m) |
|
|
|
|
||
Use Only for Short |
0 |
55 ft. (16.8 m) |
|
|
Run Installations |
1 |
47 ft. (13.7 m) |
|
|
|
|
2 |
41 ft. (12.5 m) |
|
21/2" |
|
3 |
30 ft. (9.1 m) |
|
|
|
|
|
|
(6.35 cm) |
|
4 |
22 ft. (6.7 m) |
|
|
|
|
NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.
Routing and Connecting Ductwork
Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork.
NOTE: Ductwork and fittings are NOT included and must be purchased separately.
•Use 4-in. (10.2 cm) diameter rigid or semirigid metal ductwork.
•The exhaust duct run should be as short as possible.
•Use as few elbow joints as possible.
•The male end of each section of exhaust duct must point away from the dryer.
•Use duct tape on all duct joints.
•Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.
IMPORTANT: Failure to exhaust the dryer correctly will void the dryer’s warranty.
Correct Venting |
Incorrect Venting |
15
ConnecTING GAS DRYERS
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
• Gas supply requirements:
As shipped from the factory, this dryer is configured for use with natural gas. It can be converted for use with LP (Liquefied Propane) gas. Gas pressure must not exceed 13 in. water column.
•A qualified service or gas company technician must connect the dryer to the gas service.
Failure to do so can result in fire, explosion, or death.
•Isolate the dryer from the gas supply system by closing its individual manual shutoff valve during any pressure testing of the gas supply.
Failure to do so can result in fire, explosion, or death.
•Supply line requirements:
Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1/8-in. NPT pipe plug must
be installed. Failure to do so can result in fire, explosion, or death.
•If using a rigid pipe, the rigid pipe should be
1/2-in. IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8-in. approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do so can result in fire, explosion, or death.
•Connect the dryer to the type of gas shown on the nameplate. Failure to do so can result in fire, explosion, or death.
•To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so can result in fire, explosion, or death.
•DO NOT use an open flame to inspect for gas leaks. Use a noncorrosive leak-detection fluid.
Failure to do so can result in fire, explosion, or death.
•Use only a new AGAor CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so can result in fire,
explosion, or death.
•Securely tighten all gas connections. Failure to do so can result in fire, explosion, or death.
•Use Teflon® tape or a pipe-joint compound that is insoluble in Liquefied Petroleum (LP) gas on all pipe threads. Failure to do so can result in fire, explosion, or death.
•DO NOT attempt any disassembly of the dryer; any disassembly requires the attention and tools of an authorized and qualified service person or company. Failure to do so can result in fire, explosion, or death.
Electrical Requirements for Gas Models Only
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can result in fire, explosion, or death.
•For personal safety, this dryer must be properly grounded. Failure to follow this warning can result in fire, explosion, or death.
•The power cord of this dryer is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard from this appliance. Failure to follow this warning can result in fire, explosion, or death.
•This dryer must be plugged into a
120-VAC, 60-Hz. grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to follow this warning can result in fire, explosion, or death.
•Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can result in fire, explosion, or death.
16
ConnecTING GAS DRYERS (cont.)
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier. Failure to do so can result in fire, explosion, or death.
•Use only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so can result in fire, explosion, or death.
•A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer is configured for Natural Gas when shipped from the factory. Make sure that the dryer is equipped with the correct burner nozzle for the type of gas being used (Natural Gas or Liquefied Petroleum). Failure to do so
can result in fire, explosion, or death.
•If necessary, the correct nozzle (for the LP nozzle kit order part number 4948EL4002B) should be installed by a qualified technician and the change should be noted on the dryer.
Failure to do so can result in fire, explosion, or death.
•All connections must be in accordance with local codes and regulations. Failure to do so can result in fire, explosion, or death.
•Gas dryers MUST exhaust to the outdoors.
Failure to do so can result in fire, explosion, or death.
Connecting the Gas Supply
1Make sure that the gas supply to the laundry room is turned OFF. Confirm that the type of gas available in your laundry room is appropriate for the dryer. The dryer is prepared for Natural Gas with a 3/8-in. NPT gas connection.
2Remove the shipping cap from the gas connection at the back of the dryer. Be careful not to damage the threads of the gas connector when removing the shipping cap.
3Connect the dryer to your laundry room’s gas supply using a new flexible stainless steel connector with a 3/8-in. NPT fitting.
4Securely tighten all connections between the dryer and your laundry room’s gas supply. Turn on your laundry room’s gas supply and check all pipe connections (both internal and external) for gas leaks with a noncorrosive leak-detection fluid.
|
1/8" NPT Pipe |
3/8" NPT Gas |
Plug |
Connection |
Gas Supply |
|
|
AGA/CSA-Certified |
Shutoff Valve |
|
|
Stainless Steel |
|
Flexible Connector |
|
Electrical Connection
Plug dryer into a
120-VAC, 60-Hz. grounded 3-prong outlet.
High-Altitude Installations
The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.
If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a qualified technician or gas supplier.
<![endif]>ENGLISH
17
CONNECTING ELECTRIC DRYERS
wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.
Electrical Requirements for Electric Models Only
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer has its own terminal block that must be connected to a separate 240 VAC, 60-Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE
NAMEPLATE. DO NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT CIRCUIT. Failure to follow these instructions can result in fire, explosion, or death.
•If branch circuit to dryer is 15 ft. (4.5 m) or less in length, use UL (Underwriters Laboratories) listed No.-10 AWG wire
(copper wire only), or as required by local codes. If over 15 ft. (4.50 m), use UL-listed No.-8 AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so dryer can be moved from its normal location when necessary. Failure to do so can result in fire, explosion, or death.
•The power cord (pigtail) connection between wall receptacle and dryer terminal block
IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages. Failure to follow these instructions can result in fire, explosion, or death.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January
1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so can result in fire, explosion, or death.
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not modify the plug and internal wire provided with the dryer.
•The dryer should be connected to 4-hole outlet.
•If it does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.
Special Electrical Requirements for Mobile or Manufactured Homes
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/
CSA0Z240 MH and local codes and ordinances.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
Failure to do so can result in fire, explosion, or death.
18
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Four-Wire Connection for Electric Dryers: Power Cord
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
•Use a 30-amp, 240V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.
Hot |
Neutral |
Hot |
(Black) |
(White) |
(Red) |
Ground Screw
Power Cord
Ground Wire
1Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed, 30A,
240V, 4-wire, #10 AWG-minimum copper conductor power cord through the
strain relief.
2Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cord to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cord ground wire to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
<![endif]>ENGLISH
19
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Four-Wire Connection for Electric Dryers: Direct Wire
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
1" (2.54 cm)
Ground Wire
5" (12.7 cm)
•Use UL-listed 4-wire #10 AWG-minimum copper conductor cable.
•Allow at least 5 ft (1.5 m) length to allow for removal and reinstallation of the dryer.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
1Remove 5 in. (12.7 cm) of the outer covering from the wire. Remove 5 inches of insulation from the ground wire. Cut off approximately
11⁄2 in. (3.8 cm) from the other three wires and strip 1 in. (2.54 cm) insulation from each wire. Bend the ends of the three shorter wires into a hook shape.
2Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief.
Hot |
Neutral |
Hot |
(Black) |
(White) |
(Red) |
Ground Screw
Ground Wire
3Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cable to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cable ground wire to the green ground screw. Tighten all screws securely.
Reinstall the terminal block access cover.
20
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Three-Wire Connection for Electric Dryers: Power Cord
•A 3-wire connection is NOT permitted on new construction after January 1, 1996.
•A UL-listed strain relief is required.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 3-Wire Power Cord
•Use a 30-amp, 240V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.
Hot |
Neutral |
Hot |
(Black) |
(White) |
(Red) |
Ground Screw |
|
|
Ground Wire |
|
|
1Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed, 30A,
240V, 3-wire, #10 AWG-minimum copper conductor power cord through the strain relief.
2Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
<![endif]>ENGLISH
21
CONNECTING ELECTRIC DRYERS (cont.)
USA ONLY
wWARNING:
•Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.
Three-Wire Connection for Electric Dryers: Direct Wire
•A 3-wire connection is NOT permitted on new construction after January 1, 1996.
•A UL-listed strain relief is required.
1" (2.54 cm)
1Remove 31⁄2 inches (8.9 cm) of the outer covering from the wire. Strip 1 in. (2.54 cm) insulation from each wire. Bend the ends of the three wires into a hook shape.
•Use UL-listed 3-wire #10 AWG-minimum copper conductor cable.
•Allow at least 5 ft (1.5 m) length to allow for removal and reinstallation of the dryer.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 3-Wire Power Cord
2Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief.
Hot |
Neutral |
Hot |
Black) |
(White) |
(Red) |
Ground Screw
Ground Wire
3Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. Tighten all screws securely. Reinstall the terminal block access cover.
22
SPECIAL REQUIREMENTS FOR MANUFACTURED OR MOBILE HOMES
Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/CSA0Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.
•A gas dryer must be permanently attached to the floor.
•The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided in the section Connecting Electric Dryers.
•To reduce the risk of combustion and fire, the dryer must be vented to the outside.
•DO NOT vent the dryer under a manufactured home or mobile home.
•Electric dryers may be vented to the outside using the back, left, right, or bottom panel.
•Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may not be vented to the outside using the right side panel because of the burner housing.
•The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist fire and combustion.
It is recommended that you use a rigid or flexible metal duct.
•DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other exhaust duct.
•Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 in2 (163 cm2).
•It is important that the clearance of the duct from any combustible construction be at least 2 in. (5 cm), and when venting the dryer to the outdoors, the dryer can be installed with
a clearance of 1 in. (2.54 cm) at the sides and back of the dryer.
•Please be aware that venting materials are not supplied with the dryer. You should obtain the venting materials necessary for proper installation.
FINAL INSTALLATION CHECK
Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following tests and Duct Condition Testing on the following page.
Testing Dryer Heating
GAS MODELS
Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. When the dryer starts, the igniter should ignite the main burner.
NOTE: If all air is not purged from the gas line, the gas igniter may turn off before the main burner ignites. If this happens, the igniter will reattempt gas ignition after approximately
two minutes.
ELECTRIC MODELS
Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.
Checking Airflow
Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with
a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6 in. (1.5 cm). The dryer should be checked while the dryer is running with no load.
Checking Levelness
Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all 4 leveling feet are firmly on the floor.
<![endif]>ENGLISH
23
DUCT CONDITION TESTING
Your dryer features FlowSense™, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint build-up and free of restrictions allows clothes to dry faster and reduces energy use.
NOTE: When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home.
However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same.
To activate the duct condition test cycle:
NOTE: Dryer heating test must be performed before proceeding. (Gas dryer only)
Then perform the duct condition test below.
1Press and hold the BEEPER ON/OFF and TEMP.CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFF.
2The dryer will show lnS in the number display to indicate that it is in duct condition testing mode.
3Press START/PAUSE. The dryer will run for
approximately 2 minutes to test for blockages or restrictions to air flow in the ductwork.
If no bars are shown in the display, the ductwork is free from blockages or restrictions.
If all bars are lit, the dryer ductwork has a blockage that needs to be removed immediately.
IMPORTANT: Do NOT interrupt the test cycle!
Correct Venting
Restricted or Blocked Airflow
Avoid long runs or runs with multiple elbows or bends.
Check for blockages and lint buildup.
Make sure the ductwork is not crushed or restricted.
24
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information. Important Warning: To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety Instructions, before operating this dryer.
SORTING LOADS
Fabric Care Labels
Most articles of clothing feature fabric care labels that include instructions for proper care.
Grouping Similar Items
For best results, sort clothes into loads that can be dried with the same drying cycle.
Different fabrics have different care requirements, and some fabrics will dry more quickly than others.
Fabric Care Labels
Tumble dry
Dry |
Normal |
Permanent Press/ |
||
|
|
wrinkle resistant |
|
|
Gentle/ |
Do not tumble dry |
Do not dry |
|
|
(used with |
|
|||
delicate |
|
|
do not wash) |
|
|
|
|
|
|
Heat |
|
|
|
|
setting |
|
|
|
|
High |
Medium |
|
Low |
No heat/air |
Loading the Dryer
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Check all pockets to make sure that they are empty. Items such as clips, pens, coins, and keys can damage both your dryer and your clothes. Flammable objects such as lighters or matches could ignite, causing a fire.
Failure to do so can result in fire, explosion, or death.
•Never dry clothes that have been exposed to oil, gasoline, or other flammable substances. Washing clothes will not completely remove oil residues. Failure to obey this warning can result in fire, explosion, or death.
•Combine large and small items in a load.
•Damp clothes will expand as they dry. Do not overload the dryer; clothes require room to tumble dry properly.
•Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.
CHECK THE LINT FILTER BEFORE EVERY LOAD
Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying times.
To clean, pull the lint filter straight up and roll any
lint off the filter with your fingers. Do not rinse or Lint Filter wash the filter to remove lint. Push the lint filter
firmly back into place. See “Care and Cleaning” for more information.
Always ensure the lint filter is properly installed before running the dryer. Running the dryer with a loose or missing lint filter may damage the dryer and articles in the dryer.
<![endif]>ENGLISH
25
CONTROL PANEL FEATURES
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information. Important Warning: To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
8 |
8 |
4 |
6 |
|
|
|
4 |
|
|
|
7 |
1 |
2 |
3 |
1POWER ON/OFF BUTTON
Press to turn the dryer ON. Press again to turn the dryer OFF.
NOTE: Pressing the ON/OFF button during a cycle will cancel that cycle and any load settings will be lost.
2CYCLE SELECTOR KNOB
Turn this knob to select the desired cycle.
Once the desired cycle has been selected, the standard presets will be shown in the display. On MANUAL DRY cycles, these settings can be adjusted using the cycle setting buttons anytime before starting the cycle.
3START/PAUSE BUTTON
Press this button to START the selected cycle. If the dryer is running, use this button to PAUSE the cycle without losing the current settings.
NOTE: If you do not press the START/PAUSE button to resume a cycle within 4 minutes, the dryer automatically turns off.
4MORE TIME/LESS TIME BUTTONS
To adjust the drying time, use these buttons with MANUAL DRY, TIME DRY, and steam fresh™ cycles, as well as the reduce static
|
and easy iron options. Press the MORE TIME |
|
button to increase the selected manual cycle |
|
time by a minute; press LESS TIME to decrease |
26 |
the cycle time by a minute. |
|
5
5CYCLE SETTING BUTTONS
Use these buttons to select the desired cycle settings for the selected cycle. The current settings are shown in the display. Press the button for that option to view and select other settings.
6TIME AND STATUS DISPLAY
The display shows the settings, estimated time remaining, options, and status messages for your dryer.
7OPTION BUTTONS
The OPTION buttons allow you to select additional cycle options. Certain buttons also allow you to activate special functions by pressing and holding the button for
3 seconds.
For detailed information about the individual options, please see the following pages.
8HELPFUL STEAM FUNCTIONS
During the STEAM FRESh™ cycle and when selecting Steam options, the swirl nozzle injects fabrics with hot steam to refresh, reduce static, and help make ironing easy.
CYCLE GUIDE
The cycle guide below shows the options and recommended fabric types for each cycle. |
|
|
|||||||||
Type |
Cycle |
|
Fabric Type |
Dry |
Temperature |
Time |
More Time/ Wrinkle |
Damp |
Reduce |
Easy |
|
|
Level |
in Min. |
Less Time Care |
Dry |
Static |
Iron |
|||||
|
|
|
|
|
|||||||
|
STEAM |
|
Comforter, Shirts, |
|
|
|
|
|
|
|
|
|
|
|
|
20 |
|
|
|
|
|
||
|
|
Trousers (except |
Off |
MID HIGH |
|
|
|
|
|
|
|
|
FRESHTM |
|
Adjustable |
|
|
|
|
|
|||
<![if ! IE]> <![endif]>DRY |
|
|
especially delicate fabrics) |
|
|
|
|
|
|
|
|
HEAVY DUTY |
|
Jeans, |
Normal |
HIGH |
54 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
||||
|
|
heavyweight items |
|
|
|
|
|
|
|||
<![if ! IE]> <![endif]>SENSOR |
|
Adjustable |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
COTTON/ |
|
Denims, towels, |
Normal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
MID HIGH |
55 |
|
|
|
|
|
||
|
TOWELS |
|
heavy cottons |
Adjustable |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
<![if ! IE]> <![endif]>/ |
NORMAL |
|
Work clothes, |
Normal |
MEDIUM |
41 |
|
|
|
|
|
|
|
|
|
|
|
|
|||||
<![if ! IE]> <![endif]>CYCLE |
|
|
corduroys, etc. |
Adjustable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
PERM. PRESS |
|
Permanent press, |
Normal |
|
|
|
|
|
|
|
|
|
|
LOW |
36 |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||||
<![if ! IE]> <![endif]>STEAM |
|
|
synthetic items |
Adjustable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
DELICATES |
|
Lingerie, sheets, |
Normal |
LOW |
32 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
blouses |
Adjustable |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
ULTRA |
|
Workout wear, |
Normal |
ULTRA LOW |
34 |
|
|
|
|
|
|
|
sheer or lacy |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
||||
|
DELICATE |
|
Adjustable |
|
|
|
|
|
|||
|
|
garments |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For small loads |
|
HIGH |
25 |
|
|
|
|
|
|
SPEED DRY |
|
with short |
Off |
|
|
|
|
|
|
|
|
|
Adjustable |
Adjustable |
|
|
|
|
|
|||
|
|
|
drying times |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For items that |
|
|
30 |
|
|
|
|
|
|
AIR DRY |
|
require heat-free |
|
|
|
|
|
|
|
|
<![if ! IE]> <![endif]>DRY |
|
Off |
No Heat |
|
|
|
|
|
|
||
|
drying such as |
Adjustable |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|||
|
|
plastics or rubber |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<![if ! IE]> <![endif]>MANUAL |
|
|
For general drying; |
|
HIGH |
40 |
|
|
|
|
|
TIME DRY |
|
time, temperature, |
Off |
|
|
|
|
|
|
|
|
|
|
and options can be |
Adjustable |
Adjustable |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|||
|
|
|
set manually |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wool sweaters, |
|
Off |
50 |
|
|
|
|
|
|
RACK DRY |
|
Off |
|
|
|
|
|
|
|
|
|
|
ULTRA LOW |
|
|
|
|
|
|
|||
|
|
silk, lingerie |
Adjustable |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
LOW |
|
|
|
|
|
|
<![endif]>ENGLISH
Sensor Dry Cycles
Sensor Dry cycles utilize LG’s unique dual sensor system to detect and compare the moisture level in clothes and in the air and adjust the drying time as needed to ensure superior results. The dryer automatically sets the dryness level and temperature at the recommended setting for each cycle. The estimated time remaining will be shown in the display.
Manual Dry Cycles
Use Manual Dry cycles to select a specific amount of drying time and a drying temperature. When a Manual Dry cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing MORE TIME or LESS TIME.
NOTE: To protect your garments, not every dry level, temperature, or option is available with every cycle.
27
THE DISPLAY
The display shows the settings, estimated time remaining, options, and status messages for your dryer.
6 |
2 |
3 |
1 |
|
4 |
5 |
1 Estimated Time Remaining |
5 CUSTOM PROGRAM |
When the START/PAUSE button is pressed, the display will indicate the estimated time remaining for the selected drying cycle.
2CYCLE COMPLETION INDICATOR WITH CHECK FILTER REMINDER
This portion of the display shows which stage of the drying cycle is currently underway (CHECK FILTER, DRYING, COOLING, or WRINKLE CARE).
3Child Lock Indicator
When CHILD LOCK is set, the Child Lock indicator will appear and all buttons are disabled. This prevents children from changing settings while the dryer is operating.
4CHECK FILTER REMINDER
The display will show CHECK FILTER when the dryer is turned on as a reminder to check the filter. It turns off when the START/PAUSE button is pressed.
If you have a special combination of settings that you use frequently, you can save these settings as a CUSTOM PROGRAM.
6FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The FLOW SENSE™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. This improves operating efficiency and helps minimize service calls, saving you money.
If no bars are shown in the display, the ductwork is free from blockages.
The more bars displayed, the greater the blockage.
If all bars are lit, the dryer ductwork has a blockage that needs to be removed immediately.
28