Before beginning installation, read these instructions
carefully. This will simplify installation and ensure that the
product is installed correctly and safely. Leave these
instructions near the product after installation for future
reference.
Cleaning after Every Dry .................................................................................31
Cleaning the Appliance Periodically ..............................................................33
Care in Cold Climates.......................................................................................36
TROUBLESHOOTING
Before Calling for Service................................................................................37
SAFETY INSTRUCTIONS
WARNING
SAFETY INSTRUCTIONS
3
READ ALL INSTRUCTIONS BEFORE USE
The following safety guidelines are intended to prevent unforeseen
risks or damage from unsafe or incorrect operation of the appliance.
The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as
described below.
Safety Messages
This symbol is displayed to indicate matters and operations
that can cause risks. Read the part with this symbol carefully
and follow the instructions in order to avoid risks.
WARNING
This indicates that the failure to follow the instructions can
cause serious injury or death.
CAUTION
This indicates that the failure to follow the instructions can
cause the minor injury or damage to the appliance.
WARNING
ENGLISH
To reduce the risk of explosion, fire, death, electric shock, injury or
scalding to persons when using this product, follow basic precautions,
including the following
Technical Safety
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
4
SAFETY INSTRUCTIONS
• Children should be supervised to ensure that they do not play with
the appliance.
• Do not dry unwashed items in the appliance.
• Fabric softeners, or similar products, should be used as specified by
the fabric softener instructions.
• Remove all objects from pockets such as lighters and matches.
• Never stop the appliance before the end of the drying cycle unless all
items are quickly removed and spread out so that the heat is
dissipated.
• The appliance is not to be used if industrial chemicals have been used
for cleaning.
• Items that have been soiled with substances such as cooking oil,
vegetable oil, acetone, alcohol, petroleum, kerosene, spot removers,
turpentine, waxes and wax removers should be washed in hot water
with an extra amount of detergent before being dried in the
appliance.
• Do not drink the condensed water. Failure to do so may result in foodborne illnesses.
• If the supply cord is damaged, it must be replaced by the
manufacturer or its service agents or similarly qualified person in
order to avoid a hazard.
• The lint filter must be cleaned frequently.
• Lint must not to be allowed to accumulate around the appliance.
• Do not spray dry cleaning detergent directly onto the appliance or
use the appliance to dry clothes left with dry cleaning detergent.
• Do not dry clothes stained with oil substances. Oil substances
(including edible oils) stained on clothes cannot be completely
removed even after washing with water.
• The appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly
switched on and off by a utility.
• Remove clothes from the product immediately when drying is
complete or the power is turned off during the drying process.
Leaving clothes that has been dried in the appliance unattended
SAFETY INSTRUCTIONS
could result in fire. Clothes not removed from the appliance after
drying could result in fire. Remove clothes immediately after drying,
and then hang or lay the clothes flat to cool.
• This appliance is intended to be used in household only.
Maximum Capacity
5
ENGLISH
• The maximum capacity in some cycles for clothes to be dried is
(Dry)
.
9 kg
• The recommended maximum capacity for each drying programme
may differ. To get good dry results, please refer to
in
OPERATION
chapter for further details.
Programme Table
Installation
• Make sure the appliance is properly installed, grounded, and
adjusted by qualified service personnel according to the installation
instructions.
• Never attempt to operate the appliance if it is damaged,
malfunctioning, partially disassembled, or has missing or broken
parts, including a damaged cord or plug.
• This appliance should only be transported by two or more people
holding the appliance securely.
• Do not install the appliance in a damp and dusty place. Do not install
or store the appliance in any outdoor area, or any area that is subject
to weathering conditions such as direct sunlight, wind, rain, or
temperatures below freezing.
• Tighten the drain hose to avoid separation.
• If the power cord is damaged or the hole of the socket outlet is loose,
do not use the power cord and contact an authorized service centre.
• Do not plug multiple socket outlets, an extension power cable or
adapter with this appliance.
• Items such as foam rubber (latex foam), shower caps, waterproof
textiles, rubber backed articles and clothes or pillows fitted with foam
rubber pads should not be dried in the appliance.
6
SAFETY INSTRUCTIONS
• This appliance must not be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite side to that of the
appliance, in such a way that a full opening of the appliance door is
restricted.
• This appliance must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock by
providing a path of least resistance for electric current.
• This appliance is equipped with a power cord having an equipmentgrounding conductor and a grounding power plug. The power plug
must be plugged into an appropriate socket outlet that is installed
and grounded in accordance with all local codes and ordinances.
• Improper connection of the equipment-grounding conductor can
result in risk of electric shock. Check with a qualified electrician or
service personnel if you are in doubt as to whether the appliance is
properly grounded.
• Do not modify the power plug provided with the appliance. If it does
not fit the outlet, have a proper outlet installed by a qualified
electrician.
Operation
• Do not attempt to separate any panels or disassemble the appliance.
Do not apply any sharp objects to the control panel in order to
operate the appliance.
• Do not repair or replace any part of the appliance. All repairs and
servicing must be performed by qualified service personnel unless
specifically recommended in this Owner’s Manual. Use only
authorized factory parts.
• Keep the area underneath and around the appliance free of
combustible materials such as lint, paper, rags, chemicals, etc.
• Do not put animals, such as pets into the appliance.
• Do not leave the appliance door open. Children may hang on the door
or crawl inside the appliance, causing damage or injury.
• Never reach into the appliance while it is operating. Wait until the
drum has completely stopped.
SAFETY INSTRUCTIONS
7
• Do not put in, wash or dry articles that have been cleaned in, washed
in, soaked in, or spotted with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, drycleaning solvents,
kerosene, vegetable oil, cooking oil, etc.). Improper use can cause fire
or explosion.
• In case of flood, disconnect the power plug and contact the LG
Electronics customer information centre.
• Do not push down on the door, when the appliance door is open.
• Do not touch the door during a high temperature programme.
• Do not use flammable gas and combustible substances (benzene,
gasoline, thinner, petroleum, alcohol, etc.) near the appliance.
• If the drain hose or inlet hose is frozen during winter, use it only after
thawing.
• Keep all washing detergents, softener and bleach away from
children.
• Do not touch the power plug or the appliance controls with wet
hands.
ENGLISH
• Do not bend the power cable excessively or place a heavy object on it.
Maintenance
• Securely plug the power plug in the socket outlet after completely
removing any moisture and dust.
• Disconnect the appliance from the power supply before cleaning the
appliance. Setting the controls to the OFF or stand by position does
not disconnect this appliance from the power supply.
• Never unplug the appliance by pulling on the power cable. Always
grip the power plug firmly and pull straight out from the socket
outlet.
• Do not spray water inside or outside the appliance to clean it.
Disposal
• Before discarding an old appliance, unplug it. Cut off the cable
directly behind the appliance to prevent misuse.
8
SAFETY INSTRUCTIONS
• Dispose of all packaging materials (such as plastic bags and
styrofoam) away from children. The packaging materials can cause
suffocation.
• Remove the door before disposing of or discarding this appliance to
avoid the danger of children or small animals getting trapped inside.
INSTALLATION
NOTE
NOTE
INSTALLATION
9
Parts and Specifications
• Appearance and specifications may vary without notice to improve the quality of the appliance.
Front View
a
Water Container
b
Control panel
c
Door
d
Drain Tube
Available Accessories
ENGLISH
Please contact LG Electronics Customer Information Centre or visit the LG Website at http://www.lg.com
for purchase.
a
Condensing Drain Hose and Hose Holder
b
Dry Rack
c
Stacking Kit
• The included accessories vary depending on the model you purchased.
10
WARNING
NOTE
5 cm1 cm1 cm
INSTALLATION
Specifications
Asterisk(s) means model variant and can be varied (0-9) or (A-Z).
ModelTD-H90V*D
Power supply220 - 240 V~, 50 Hz
Dimension (Width X Depth X Height)600 mm X 690 mm X 850 mm
Product weight56 kg
Allowable temperature5 - 35 ℃
Installation Place
Requirements
Before installing the appliance, check the following
information to make sure that the appliance
should be installed in a correct place.
Installation Location
• Do not install the appliance around a heat
source. The rear side of the appliance must be
well ventilated. Failure to follow these
instructions may result in problems.
• The appliance is not designed for maritime use
or for use in mobile installation such as caravans,
aircraft and etc.
• Do not install the appliance as a built-in
appliance. It is not suitable for built-in purpose.
• For better drying performance, keep the rear of
the appliance away from the wall.
• Make sure that the location where the appliance
will be installed meets a minimum clearance
conditions.
• Install the appliance on a flat hard floor.
Allowable slope under the appliance is 1 degree.
• Never try to correct any unevenness in the floor
with pieces of wood, cardboard or similar
materials under the appliance.
• Install the appliance in a location where service
engineers are easily accessible in the event of a
breakdown.
• Do not install the appliance next to hightemperature appliances such as refrigerator,
oven or stove, and etc. It can cause poor drying
performance and delay programme duration. It
also adversely affect the proper functioning of
the compressor.
• Do not install the appliance where there is a risk
of frost or dust. The appliance may not be able to
operate properly or may be damaged by
freezing of condensed water in the pump and
drain hose.
• With the appliance installed, adjust all four feet
using a spanner to ensure the appliance is
stable, and a clearance of approximately 20 mm
is left between the top of the appliance and the
underside of any work-top.
Ventilation
• Alcove or under counter
3
- Ensure airflow of 3.17 m
appliance.
/mm through the
INSTALLATION
NOTE
NOTE
NOTE
NOTE
WARNING
11
• Cupboard
- Cupboard door must have 2 (louvered)
opening, each have a minimum area of 387
2
cm
, located 8 cm from bottom and top of the
door.
• Make sure that air circulation around the
appliance is not impeded by carpets, rugs, and
etc.
Ambient Temperature
• Do not install the appliance in rooms where
freezing temperatures may occur. Frozen hoses
may burst under pressure. The reliability of the
electronic control unit may be impaired at
temperatures below freezing point.
• If the appliance is delivered in winter and
temperatures are below freezing, place the
appliance at room temperature for a few hours
before putting it into operation.
• The appliance performs best at a room
temperature of 23 ℃.
Electrical Connection
• Do not use an extension cord or double adapter.
• Do not overload the outlet with more than one
appliance.
• Connect the appliance to an earthed socket in
accordance with current wiring regulations.
• The appliance must be positioned a place close
to outlet socket so that the plug is easily
accessible.
• Outlet socket must be within 1.5 meters of either
side of the location of the appliance.
Leveling the Appliance
Checking Leveling
Leveling the appliance prevents unnecessary noise
and vibration. Check whether the appliance is
perfectly level after installation.
• If the appliance rocks when pushing the top
plate of the appliance diagonally, adjust the feet
again.
• Timber or suspended type flooring may
contribute to excessive vibration and unbalance.
Re-enforcement or bracing of the timber floor
may need to be considered to stop or reduce
excessive noise and vibration.
• Do not install the appliance on any elevated
surface, stand or plinth as it can become
unstable and fall causing serious injury and
damage.
Adjusting and Leveling the
Appliance
When the appliance is not perfectly level, turn the
adjustable feet until the appliance no longer
wobbles.
• Turn the adjustable feet clockwise to raise or
turn the adjustable feet counterclockwise to
lower from front-to-back, side-to-side and
corner-to-corner.
Reversing the door
You can reverse the door for your convenience.
ENGLISH
• Always unplug the appliance after use.
• Do not reverse the door while the appliance is
stacked on a washing machine.
12
WARNING
NOTE
WARNING
INSTALLATION
• Before removing the hinge screws, have an
assistant support the weight of the door. The
door could fall on the floor due to the weight of
the door.
• For safety reasons, two or more people need to
work together to reverse the door.
• The appearance of the screws varies and the
screws must be inserted differently depending
on the position. Make sure the screw is properly
selected before tightening.
1
Open the door and remove 2 screws on the
door hinge
the door down carefully from the cabinet
with the front side facing down to the floor.
a
. After removing the screws, put
b
• There are 6 screws on the front and 2 screws
on the side.
3
Remove the 3 screws from the door latch
assembly
and the hinge assembly, and then remove the
screw which is fixed on the door hook.
d
which is fixed between the door
• Remove the lower screw first. The door may fall
on to the floor due to its weight and the door can
be damaged.
2
Remove 8 screws on the hinge assembly c
from the door.
4
Swap the position of the hinge assembly c and
the door latch assembly
the screws in reverse order.
• Tighten the screw in their proper position
referring from steps 2 to 4.
d
and then tighten
INSTALLATION
NOTE
13
5
Remove the door catch e from the appliance
frame by removing 2 screws and then
assemble them on the opposite side.
6
Remove the 2 decorative screws from the
appliance frame and then assemble them on
opposite side.
qualified service personnel to ensure it has been
installed correctly.
The qualified personnel will ensure you have the
correct stacking kit for your model of LG front load
washing machine and will ensure it is firmly fixed.
For these reasons, expert fitting is essential.
• Some models are not sold with all of the
available accessories, you may need to purchase
the LG stacking kit first if it was not provided with
your model. Please contact LG Electronics
Customer Information Centre or visit the LG
Website at http://www.lg.com for purchase.
Stacking Kit
In order to stack the appliance, an LG stacking kit is
required.
ENGLISH
7
Install the door with the screws removed in
step 1 and then check the door closes properly.
Stacking Instructions
The appliance can be placed on top of an LG front
load washing machine and securely fixed with a
stacking kit. This installation must be conducted by
a
Dryer
b
LG Front Load Washing Machine
The appliance may only be stacked on top of an LG
front load washing machine. Do not attempt to
stack the appliance on any other washing machine,
as it could result in damage, injury or property
damage.
Shape and
assembly
direction
Washing Machine Top plate
size
550 mm600 mm
14
WARNING
CAUTION
b
a
INSTALLATION
Installation Procedure
5
Use the 4 screws in the accessory box (16 mm)
to assemble the washing machine rear cover
and stacking kit.
• For safety reasons, installation procedure should
be performed by two or more qualified service
personnel.
• The weight of the appliance and the height of the
installation makes the installation procedure too
risky for one person.
• Incorrect installation can cause serious
accidents.
• Do not operate if the appliance is not properly
stacked.
1
Place the appliance on the top of an LG front
load washing machine.
2
Remove the 2 screws from the bottom of the
rear cover on each side.
3
Align the LG stacking kit holes and the rear
cover holes in a line.
• In case of the top plate size is 600 mm
6
The procedure for the opposite side will be the
same.
Installing the Optional Drain
Hose
Normally, condensed water is pumped up to the
water container where water is collected until
manually emptied. Water can also be drained out
directly to a mains drain, especially when the
appliance is stacked on top of a washing machine.
With the connecting elbow or T piece of the mains
drain hose, simply change the water path and reroute to the drainage facility as below:
1
Separate the anti-backflow lid a and the water
container hose
or T piece.
2
Attach the anti-backflow lid a to the head of
the connecting elbow or T piece and then
connect the optional drain hose
opposite side of the connecting elbow or T
piece.
b
from the connecting elbow
c
to the
• In case of the top plate size is 550 mm
4
Fasten the 2 screws that were removed earlier
from the appliance to the stacking kit.
a
c
• If the optional drain hose is installed in a way
that leaves it bent or pinched, drainage may not
function properly.
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.