LG S43A1-D, NB4530A User Manual

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

SLOVENŠČINA

ITALIANO ESPAÑOL

OWNER’S MANUAL

Sound Bar System

Please read this manual carefully before operating
your set and retain it for future reference.

NB4530A (NB4530A, S43A1-D)

ΕΛΛΗΝΙΚΑ

PORTUGUÊS

1 Getting Started

Getting Started2

Safety information

1

Getting Started

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR BACK) NO

USER-SERVICEABLE PARTS INSIDE REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.

WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built­in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This lightning ash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sucient
magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon
a dedicated circuit;

That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. hen installing the product, ensure
that the plug is easily accessible.

This device is equipped with a portable battery or
accumulator.

Safety way to remove the battery or the
battery from the equipment: Remove the

old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.

CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, should be placed on the
apparatus.

Getting Started 3

Disposal of your old appliance

1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.

2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.

3. The correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.

4. For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.

Disposal of waste batteries/accumulators

1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product
it means they are covered by
European Directive 2006/66/EC.

2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the
battery Contains more that 0.0005%
of mercury,0.002% of cadmium or

0.004% of lead.

3. All batteries/accumulators should
be disposed separately from
the municipal waste stream via
designated collection facilities
appointed by the government or
the local authorities.

4. The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.

5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your
city office, waste disposal service or
the shop where You purchased the
product.

1

Getting Started

Getting Started4

Europe Notice

LG Electronics hereby declares that this/these

1

product(s) is/are in compliance with the essential

Getting Started

requirements and other relevant provisions of
Directive 1999/5/EC, 2004/108/EC, 2006/95/EC and
2009/125/EC.

Please contact to the following address for
obtaining a copy of the DoC (Declaration of
Conformity).

Contact oce for compliance of this product :

LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands

yPlease note that this is NOT a Customer Service

contact point. For Customer Service Information,
see Warranty Card or contact the dealer that you
purchased this product.

Indoor Use Only

RF Radiation Exposure Statement

This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body.

Italy Notice

A general authorization is requested for outdoor
use in Italy.
The use of these equipments is regulated by:

1. D.L.gs 1.8.2003, n. 259, article 104 (activity
subject to general authorization) for outdoor
use and article 105 (free use) for indoor use, in
both cases for private use.

2. D.M. 28.5.03, for supply to public of RLAN access
to networks and telecom services.

L’uso degli apparati è regolamentato da:

1. D.L.gs 1.8.2003, n. 259, articoli 104 (attività
soggette ad autorizzazione generale) se utilizzati
al di fuori del proprio fondo e 105 (libero uso) se
utilizzati entro il proprio
fondo, in entrambi i casi per uso private.

2. D.M. 28.5.03, per la fornitura al pubblico
dell’accesso R-LAN alle reti e ai servizi di
telecomunicazioni.

Brazil Notice

Este equipamento opera em caráter secundário, isto
é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e
não pode causar interferência a sistemas operando
em caráter primário.

Table of Contents 5

Table of Contents

1 Getting Started

2 Safety information
6 Unique features
6 – Portable In
6 – Speaker ez (easy) Setup
6 Introduction
6 – Symbols Used in this Manual
6 Accessories
7 Remote control
8 Front panel
8 Rear panel
9 Installing the sound bar
9 Installing the cover foot

2 Connecting

10 Mounting the main unit on a wall
12 Connecting the AC adapter
12 Setting up
12 – Pairing wireless subwoofer
13 Connecting to your TV
13 – Using an HDMI cable
13 – What is SIMPLINK?
14 – ARC (Audio Return Channel) function
14 – Additional information for HDMI
15 – Using an OPTICAL cable
16 Optional equipment connection
16 – HDMI connection
17 – PORT. (Portable) IN connection
17 – Listening to music from your portable

player
17 – OPTICAL IN connection
17 – Speaker ez (easy) setup
18 – USB playback
18 – Playable file

3 Operating

19 Basic operations
19 – USB operation
19 Other operations
19 – DRC (Dynamic Range Control)
19 – AV Sync
20 – AUTO POWER On/Off
20 – Auto Power Down
20 – Turn off the sound temporarily
20 – Displaying file and input source
21 – Sleep timer setting
22 Sound adjustment
22 – Setting the surround mode
22 – Auto Volume On/ Off
22 – Adjust the woofer level settings
23 Using Bluetooth technology
23 – Listening to music stored on the

Bluetooth devices

25 Controlling a TV with the supplied remote

control

25 – Setting up the remote to control your

TV

4 Troubleshooting

26 Troubleshooting

5 Appendix

27 Trademarks and licenses
28 Specifications
29 Maintenance
29 – Handling the unit

1

2

3

4

5

Getting Started6

Unique features

Portable In

1

Getting Started

Listen to music from your portable device. (MP3,
Notebook, etc)

Speaker ez (easy) Setup

Listen to sound from TV, DVD or Digital device with
vivid 2.1 or 2.0 ch mode.

Introduction

Symbols Used in this Manual

Note

,

Indicates special notes and operating features.

Caution

>

Indicates cautions for preventing possible damages
from abuse.

Accessories

Please check and identify the supplied accessories.

Remote control (1) Batteries (2)

HDMI Cable (1)

AC adapter (1) USB Cable (1)

Power cord (1)

Wall bracket (1) Wall Mount Bracket

Cover foot_19mm (1) Shaft wall mount (2)

Installation Template
(1)

Getting Started 7

Remote control

Battery Installation

Remove the battery cover on the rear of the
Remote Control, and insert two (size AAA) battery
with and matched correctly.

• • • • • • • • • • a • • • • • • • • •

(Power) : Switches the unit ON or OFF.

1

FUNCTION : Selects the function and the input
source.

FOLDER : Searches for a folder of MP3/WMA

W/S

les. When a USB containing MP3/WMA les in
several folders is being played,
press
to play.

OPTICAL : Changes input source to OPTICAL
directly.

MUTE @ : Mutes the sound.

VOL +/- : Adjusts speaker volume.

• • • • • • • • • • b • • • • • • • • •

AUTO POWER : This function is automatically
turned on the unit. (Refer to the page 20)

AV SYNC : Synchronizes the audio and video.

INFO : Displays the information of a le or an input

source.

REPEAT : Listens to your les repeatedly or
randomly.

C/V

- Skips Fast backward or Forward.

- Searches for a section within a le.

(Stop) : Stops playback.

Z
d/M

playback.

SOUND EFFECT : Selects a sound eect mode.

AUTO VOLUME : Turns on and o the AUTO

VOLUME mode.

WOOFER LEVEL : Sets the sound level of woofer.

• • • • • • • • • • c • • • • • • • • •

0 to 9 numerical buttons : Selects a le directly.

DRC : Sets the DRC.

SLEEP : Sets the system to turn o automatically at

a specied time.

• • • • • • • • • • d • • • • • • • • •

TV Control buttons : See page 25.

FOLDER to select the folder you want

W/S

(Skip/Search) :

(Play/Pause) : Starts playback. / Pauses

1

Getting Started

Getting Started8

Front panel

1

Getting Started

A 1/!

- / + (Volume -/+)

B

Adjusts volume level.

(Play/Pause)

C T

(Stop)

D I

F (Function)

E

Selects the function and input source.

Display window

F

Rear panel

Caution

>

Precautions in using the touch buttons

yUse the touch buttons with clean and dry

hands.

- In a humid environment, wipe out any
moisture on the touch buttons before
using.

yDo not press the touch buttons hard to

make it work.

- If you apply too much strength, it can
damage the sensor of the touch buttons.

yTouch the button that you want to work in

order to operate the function correctly.

yBe careful not to have any conductive

material such as metallic object on the
touch buttons. It can cause malfunctions.

DC. IN 25V 0 2A

A

USB port

B

PORT.(Portable) IN

C

OPT.(Optical) IN

D

HDMI IN/ OUT

E

Getting Started 9

Installing the sound
bar

You can hear the sound by connecting the unit to
the other device : TV, Blu-ray disc player, DVD player,
etc.

Place the unit in front of the TV and connect it to
the device you want. (Refer to pp.13 - 18)

Installing the cover
foot

1. Turn the unit upside down.

2. Place the cover foot on the bottom of the unit
to match screw holes with those on the unit.

3. Fix it with screws as shown in the illustration
above.

Note

,

26mm

19mm

(It has been already
installed to the unit.)

1

Getting Started

Install proper cover foot of either 19mm or
26mm in height to match the unit to the
underpart of TV screen at the suitable level.
(26mm cover foot has been already installed to
the unit.)

Connecting10

Mounting the main
unit on a wall

You can mount the main unit on a wall.
Detach the cover foot of the unit, keep the
detached cover foot for later installation and use
the screws to hang the unit on the wall.

Prepare shaft wall mount and brackets.

2

Connecting

Unit

Wall Mount Bracket
Installation Template

1. Locate the shaft wall mount on the screw hole
of the unit's back and then fix it onto the unit
with the screw.

Wall bracket

Shaft wall mount

2. Match the TV’s BOTTOM EDGE of Wall Mount
Bracket Installation Template with the bottom
of TV and attach to the position.

TV

3. When you mount it on a wall (concrete), use the
wall plugs. You should drill some holes. A guide
sheet (Wall Mount Bracket Installation Template)
is supplied to drill. Use the sheet to check the
point to drill.

Connecting 11

4. Remove the Wall Mount Bracket Installation
Template.

5. Fix it with screws as shown in the illustration
below.

6. Hang the main unit onto the bracket as shown
below.

Note

,

Detach the unit from the bracket as shown
below.

2

Connecting

Caution

>

yDo not hang onto the installed unit and

avoid any impact to the unit.

ySecure the unit rmly to the wall so that it

does not fall o. If the unit falls o, it may
result in an injury or damage to the product.

yWhen the unit is installed on a wall, please

make sure that a child does not pull any of
connecting cables, as it may cause it to fall.

Connecting12

Connecting the AC
adapter

1. Connect the supplied AC power cord to the AC
adapter.

2. Connect the AC adapter cable to DC. IN adapter
input.

3. Plug the AC power cord into an AC outlet.

2

Connecting

Caution

>

Only use the AC adapter supplied with this
device. Do not use a power supply from
another device or manufacturer. Using any
other power cable or power supply may cause
damage to the device and void your warranty.

Setting up

Pairing wireless subwoofer

LED indicator of wireless subwoofer

LED Color Status

Yellow The wireless subwoofer is

Yellow (blink) The wireless subwoofer is trying

Red The Wireless subwoofer is in

O (No
display)

Setting up the wireless subwoofer
for the first time

1. Connect the power cord of the Wireless
subwoofer to the outlet.

2. Turn on the main unit : The main unit and
wireless subwoofer will be automatically
connected.

Manually pairing wireless subwoofer

When your connection is not completed, you can
see the red LED on the woofer and woofer is not
made sound. To solve the problem, follow the
below steps.

1. Press and hold I STOP button on the unit
and MUTE
simultaneously.

- Displays the “REMATE”.

2. Press PAIRING on back of the woofer.

- The yellow LED will flicker.

3. Turn off and on the unit.

- If you see “yellow” LED, it’ s successful.

4. If you don’t see “Yellow” LED, try again Step 1 ­Step 3.

receiving the signal of the unit.

to connect.

standby mode.

The power cord of wireless
subwoofer is disconnected.

button on the remote control

Note

,

yIf you operate main unit then wireless

subwoofer sound within a few seconds in
standby mode.

ySet the distance between this unit and

wireless subwoofer within 10 m (32 ft.).

yOptimum performance can be

implemented only when the unit and
the Wireless subwoofer within distance
of 2 m (6 ft.) to 10 m (32 ft.) is used since
communication failure may occur if longer
distance is used.

yIt takes a few seconds (and may take longer)

for the unit and subwoofer to communicate
with each other.

Connecting to your TV

You can listen to the sound from your TV via the
unit. There are two ways of connecting your TV to
the unit.

Using an HDMI cable

You must connect the TV that supports ARC
function if you want to listen to TV sound using an
HDMI cable. And turn on SIMPLINK of your TV.

1. Connect the HDMI OUT jack on the back of
the unit to ARC jack on the TV using an HDMI
cable (Type A, High speed HDMI™ cable with
Ethernet).

Connecting 13

What is SIMPLINK?

Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.

Controllable functions by LG TV’s remote control :
Power on/o, volume up/down, etc.

Refer to the TV owner’s manual for the details of
SIMPLINK function.

LG TV’s with SIMPLINK function has the logo as
shown above.

Note

,

Depending on the state of the unit, some
SIMPLINK operation may dier from your
purpose or not work.

2

Connecting

HDMI cable

2. Turn TV and the unit on. ARC function is
selected automatically.

Connecting14

ARC (Audio Return Channel)
function

The ARC function enables an HDMI capable TV to
send the audio stream to HDMI OUT of the unit.

To use this function :

-Your TV must support the HDMI-CEC and ARC
function and the HDMI-CEC and ARC must be
set to On.

2

-The setting method of HDMI-CEC and ARC may

Connecting

dier depending on the TV. For details about
ARC function, refer to your TV manual.

-You must use the HDMI cable (Type A, High
Speed HDMI™ cable with Ethernet).

-You must connect the HDMI OUT on the unit
with HDMI IN of the TV that supports ARC
function using an HDMI cable.

-You can connect only one Sound bar to TV
compatible with ARC.

Additional information for
HDMI

yWhen you connect a HDMI or DVI compatible

device make sure of the following:

- Try switching off the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device
and leave it for around 30 seconds, then switch
on this player.

- The connected device’s video input is set
correctly for this unit.

- The connected device is compatible with
720 x 480p, 1280 x 720p, 1920 x 1080i or
1920 x 1080p video input.

yNot all HDCP-compatible HDMI or DVI devices

will work with this player.

- The picture will not be displayed properly with
non-HDCP device.

Note

,

yIf a connected HDMI device does not accept

the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.

yChanging the resolution when the

connection has already been established
may result in malfunctions. To solve the
problem, turn o the player and then turn it
on again.

yWhen the HDMI connection with HDCP

is not veried, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.

yIf there are noises or lines on the screen,

please check the HDMI cable (length is
generally limited to 4.5 m(15 ft).

yYou cannot change the video resolution

in the HDMI IN mode. Change the video
resolution of the connected component.

yIf the video output signal is abnormal when

your personal computer is connected to
HDMI IN jack, change the resolution of your
personal computer to 480p, 720p, 1080i or
1080p.

Connecting 15

Using an OPTICAL cable

1. Connect the OPT. IN jack on the back of the
unit to OPTICAL OUT jack on the TV using an
OPTICAL cable.

2

Connecting

Optical cable

2. Set the INPUT source to OPTICAL. Press
repeatedly FUNCTION on the remote control or
F on the unit until the function is selected.

For selecting directely the OPTICAL function,

press OPTICAL on the remote control.

Connecting16

Optional equipment
connection

HDMI connection

For enjoying sound only

2

You can enjoy the sound from the external device

Connecting

you connect.

To the Blu-ray disc player,
DVD player, etc.

1. Connect HDMI IN jack on the back of the unit to
HDMI OUT jack on the audio device such as Blu­ray disc player, DVD player, etc.

2. Set the INPUT source to HDMI IN. Press
repeatedly FUNCTION on the remote control or
F on the unit until the function is selected.

For enjoying both sound and picture

You can enjoy both sound and picture from the
external device you connect.

Blu-ray disc player,
DVD player, etc.

1. Connect HDMI IN jack on the back of the unit to
HDMI OUT jack on the external device such as
Blu-ray disc player, DVD player, etc.

2. Connect HDMI OUT jack on the back of the unit
to HDMI IN jack on the TV.

3. Set the INPUT source to HDMI IN. Press
repeatedly FUNCTION on the remote control or
F on the unit until the function is selected.

Note

,

yWith the unit connected to external devices

and TV as above illustration,
TV will output picture and sound from
external devices when the unit is turned o
in HDMI IN mode.

yEven though PCM multi channel is inputted

to the unit through an HDMI cable, the unit
can only output 2 channel.

Connecting 17

PORT. (Portable) IN
connection

MP3 player,
etc...

Listening to music from your
portable player

The unit can be used to play the music from many
types of portable players or external devices.

1. Connect the portable player to the
PORT. (Portable) IN connector of the unit.

2. Turn the power on by pressing 1 (Power).

3. Select the PORTABLE function by pressing
FUNCTION.

4. Turn on the portable player or external device
and start playing it.

OPTICAL IN connection

Connect an optical output jack of external devices
to the OPT. IN jack.

2

Connecting

To the digital

optical output jack

of external device

Speaker ez (easy) setup

Listens to sound from TV, DVD or Digital Device
with 2.1 or 2ch mode.

1. Connect the OPT. IN jack on the back of the unit
to optical out jack of your TV (or digital device
etc.)

2. Select the input source to OPTICAL directly by
pressing OPTICAL.

3. Listen to sound with 2.1 or 2ch speaker.

4. Press OPTICAL to exit from OPTICAL.
Function is retuned to previous one.

Connecting18

USB playback

Connect USB memory device to the USB port on
the back of the unit.

With the unit on the wall, you can connect USB
more easily using supplied USB cable.

2

Connecting

Removing the USB Device from the unit.

1.

Choose a different function/mode or press

twice in a row.

Z

2. Remove the USB device from the unit.

Playable file

MP3/ WMA file requirement

MP3/ WMA le compatibility with this unit is limited
as follows :

ySampling frequency : within 32 to 48 kHz (MP3),

within 32 to 48 kHz (WMA)

yBit rate : within 32 to 320 kbps (MP3),

40 to 192 kbps (WMA)

yMaximum les : Under 999

yFile extensions : “.mp3”/“.wma”

yA protected le by DRM(Digital rights

management) cannot be played on the unit.

Compatible USB devices

yMP3 Player : Flash type MP3 player.

yUSB Flash Drive : Devices that support USB1.1.

yThe USB function of this unit does not support

some USB devices.

USB device requirement

yThe le name is limited to 255 characters.

yUsing NTFS le system is not supported.

(Only FAT(16/32) le system is supported.)

yDepending on the size and the number of the

les, it may take several minutes to read the
contents on the media.

yDevices which require additional program

installation connected to a computer, are not
supported.

yDo not extract the USB device while in operation.

yFor a large capacity USB, it may take longer than

a few minutes to be searched.

yTo prevent data loss, back up all data.

yIf you use a USB extension cable or USB hub, the

USB device is not recognized.

yThis unit is not supported when the total

number of les is 1000 or more.

yExternal HDD, Card readers, Locked devices,

or hard type USB devices are not supported.

yThe unit’s USB Port cannot be connected to PC.

The unit can not be used as a storage device.

Operating 19

Basic operations

USB operation

1. Connect the USB device to the USB port.

2. Select the USB function by pressing FUNCTION.

3. Select a file you want to play by pressing
or V.

C

To Do this

Stop Press Z.

Playback Press

Pause

Skip to the next/

previous le

Search for a

section within a

le

Play repeatedly

or randomly

Select a le

directly

Resume

playback

During playback, press

During playback, press C
or V to go to the next le
or to return to the beginning
of the current le.

Press C twice briey to
step back to the previous le.

Press and hold
during playback and release it
at the point you want to listen
to.

Press REPEAT on the remote
control repeatedly, the
display will be changed in the
following order, RPT 1
D (DIRECTORY) RPT ALL
RANDOM OFF.

Press 0 to 9 numerical buttons
on the remote control to go
to the desired le directly.

The unit memorizes the point at
which you've changed function
or the unit had been turned o.

d/M

.

C/V

d/M

RPT

.

Other operations

DRC (Dynamic Range Control)

Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [DRC ON] by using
DRC.

AV Sync

When receiving audio signals from TV, sound and
images may not be matched. In the case, this
function can adjust the delay time.

1. Press AV SYNC.

2. Use

C/V

the delay amount, which you can set at
anything between 0 and 300ms.

to scroll up and down through

3

Operating

Note

,

The resume point may be cleared when you
pull out the power cord or removing the USB
device from the unit.

Operating20

AUTO POWER On/Off

Before operating this function, make sure that
you have selected OPTICAL and turn on the AUTO
POWER.

This function automatically turns on/o the unit
when you turn on/o the external device (T V, DVD
Player, Blu-ray Disc Player, etc.) connected to this
unit by the optical cable. This function turns on or
o each time you press AUTO POWER.

Display Operation

AUTO POWER function is
turned on.

AUTO POWER function is
turned o.

3

Operating

AUTO POWER ON

AUTO POWER OFF

Note

,

yThis function is intentionally designed to

turn o the unit after 1 minute of inactivity
in OPTICAL mode. Only if the unit has
already received the signal transmitted
through the optical source and there is no
digital audio signal going to the unit, the
unit will turn o after 1 minute of inactivity
with AUTO POWER function is turned on.

yDepending on the connected device by the

optical cable, this function may not operate.

yIf you want to use AUTO POWER, SIMPLINK

must be turned o. It takes for about 30
seconds to switch on or o SIMPLINK.

yIf SIMPLINK is set to ON, "AUTO POWER OFF"

is just scrolled, even thouth you press AUTO
POWER.

yOnce AUTO POWER is set, the unit will

start as OPTICAL mode automatically next
time, no matter what kind of function you
selected before.

Auto Power Down

This unit will be o itself to save electronic
consumption in the case main unit is not
connected to external device and is not used for 25
minutes.

So does this unit after six hours since Main unit
has been connected to other device using analog
input.

But the unit can turns on automatically based on
the [AUTO POWER] function you've set.

Turn off the sound temporarily

Press MUTE@ to mute your unit.

You can mute your unit, for example, to answer
the telephone, “MUTE” is displayed in the display
window.

To cancel it, press MUTE@ again on the remote
control or change the volume level.

Displaying file and input
source

You can display various information of the input
source by pressing INFO.

USB : MP3/WMA containing le information

OPTICAL/ARC/HDMI IN : Audio format, Audio
channel

Sleep timer setting

Press SLEEP repeatedly to select the desired time
period options (in minutes):

LCD OFF(Display window o) -> DIMMER( The
display window will be darken by half ) -> Sleep
timer value -> Display on

In display window you see “LCD OFF” and the
display window turns o .

To check the remaining time, press SLEEP.

To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.

Note

,

You can check the remaining time before the
unit turns o . Press SLEEP the remaining time
appears in the display window.

Operating 21

3

Operating

Operating22

Sound adjustment

Setting the surround mode

This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.

The displayed items for the equalizer may be
different depending on sound sources and effects.

On Display Description

You can enjoy comfortable
and natural sound.

You can enjoy the sound
without equalizer eect.

The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound eect.

The CLRVOICE is Clear Voice.
This program make voice
sound clear, improving the
quality of voice sound.

The GAME is Game Equalizer.
You can enjoy more virtual
sound while playing video
games.

The NIGHT is Night Mode.
This may be useful when you
want to watch movies at low
volume late at night.

The UPSCALER is MP3 Up­Scaling. When listening to
MP3 les or other compressed
music, you can enhance the
sound. This mode is available
only to 2 channel sources.

Improves the bass and treble
sound.

You can enjoy more immersive
and cinematic surround
sound.

3

Operating

NATURAL

BYPASS

BASS

CLRVOICE

GAME

NIGHT

UPSCALER

LOUDNESS

3D SOUND

Note

,

yIn some of surround modes, some speakers,

there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.

yYou may need to reset the surround mode,

after switching the input, sometimes even
after the sound le changed.

Auto Volume On/ Off

With AUTO VOLUME function on, the unit automacally
adjusts the outputted volume level to make it raised
or lowered if the sound is too loud or small.
So you can enjoy the sound at comportable level
not too loud or small.

Press AUTO VOLUME to turn on or o the Auto
Volume mode.

Adjust the woofer level
settings

You can adjust the sound level of woofer.

1. Press WOOFER LEVEL.

2. Press VOL +/- to adjust the sound level of the
woofer.

Operating 23

Using Bluetooth
technology

About Bluetooth

Bluetooth® is wireless communication technology
for short range connection.

The available range is within 10 meters.

(The sound may be interrupted when the
connection interfered by the other electronic wave
or you connect the bluetooth in the other rooms.)
Connecting individual devices under
Bluetooth® wireless technology does not incur any
charges. A mobile phone with
Bluetooth® wireless technology can be operated
via the Cascade if the connection was made via
Bluetooth® wireless technology.
Available Devices : Mobile phone, MP3, Laptop,
PDA (This units be supported the Stereo Headset.)

Bluetooth Profiles

In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.

A2DP (Advanced Audio Distribution Profile)

Listening to music stored on
the Bluetooth devices

Pairing your unit and Bluetooth
device

Before you start the pairing procedure, make
sure the Bluetooth feature is turned on in to your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed,
it does not need to be performed again.

1. Select the Bluetooth function by using the
FUNCTION.
Appears “BT” and then “BT READY” in display
window.

2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device.Your unit appears as “LG SOUND BAR”.

3. Enter the PIN code.
PIN code : 0000

4. When this unit is successfully connected with
your Bluetooth device, “PAIRED” will appear on
the display window.

Note

,

Depending on the Bluetooth device type,
some device have a dierent pairing way.

3

Operating

5. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.

Note

,

If you change the function of the unit, the
Bluetooth function is disconnected, operate
pairing again.
(Bluetooth
Bluetooth)

Function other than the

3

Operating

Operating24

Note

,

yThe sound may be interrupted when

the connection interfered by the other
electronic wave.

yYou cannot control the Bluetooth device

with this unit.

yPairing is limited one Bluetooth device per

one unit and multi-pairing is not supported.

yAlthough the distance between your

Bluetooth and the set is less than 10m, there
are obstacles between both, your Bluetooth
device cannot be connected.

yDepending on the type of the device,

you may not be able to use the Bluetooth
function.

yYou can enjoy wireless system using phone,

MP3, Notebook, etc..

yWhen not connected the Bluetooth, “BT

READY” appears on the display window.

yThe Electrical malfunction due to devices

using same frequency such as Medical
equipment, Microwaves or wireless
LAN devices, the connection will be
disconnected.

yWhen someone stands and interrupts

communication between Bluetooth device
and the player, the connection will be
disconnected.

yIf the gotten away of the distance between

Bluetooth and the unit, the sound quality
is lower and lower the connection will
disconnect when the space between the
Bluetooth and the unit gets out of the
operating range of Bluetooth.

yThe device with Bluetooth wireless

technology is disconnected, if you turn o
the main unit or put the device away from
the main unit more than 10m.

Operating 25

Controlling a TV with
the supplied remote
control

You can control your TV using the buttons below.

VOL +

PR/CH

AV/INPUT

Button Operation

MUTE

@

AV/INPUT

(TV POWER) Turn the TV on or o.

1

VOL +/–

PR/CH

W/S

Note

,

yDepending on the TV being connected, you

may not be able to control your TV using
some of the buttons.

yThe remote control of the unit performs

basic operation of your TV. Please use the
TV’s remote control to enjoy advanced
operation of your TV.

PR/CH

VOL -

Turn the TV’s volume on or
o.

Switch the TV’s input source
between the TV and other
input sources.

Adjust the volume of the
TV.

Scan up or down through
memorized channels.

Setting up the remote to
control your TV

You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.

1. While holding down 1 (TV POWER) button, and
press the manufacturer code for your TV with
the numerical buttons (see the table below).

Manufacturer Code Number

LG 1(Default), 2

Zenith 1, 3, 4

GoldStar 1, 2

Samsung 6, 7

Sony 8, 9

Hitachi 4

2. Release the 1 (TV POWER) button to complete
setting.

Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.

3

Operating

4 Troubleshooting

Troubleshooting26

Troubleshooting

PROBLEM CAUSE & CORRECTION

No Power

No sound

No display

The remote control

4

Troubleshooting

does not work

properly.

yThe power cord is unpluged.

Plug in the power cord.

yCheck the condition by operating other electronic devices.

yIncorrect input source is selected.

Check the input source and select the correct input source.

yThe mute function is activated.

Press MUTE@ or adjust the volume level to cancel the mute function.

yThe LCD OFF function is activated.

Press SLEEP to cancel the function.

yThe remote control is too far from the unit.

Operate the remote control within about 23 ft (7m).

yThere is an obstacle in the path of the remote control and the unit.

Remove the obstacle.

yThe batteries in the remote control is exhausted.

Replace the batteries with new one.

The AUTO POWER
function does not

work.

When you sense that

outputted sound of

the unit is low.

yCheck the state of SIMPLINK and turn o SIMPLINK.

yDepending on the connected device by the optical cable, this function may not

operate.

Check the details below and adjust the unit according to them.

ySwitch [ON] state of DRC function to [OFF] by using remote controller.

yWith the sound bar connected with TV, change the AUDIO DIGITAL OUT setting

on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM].

yWith the sound bar connected with Player, change the AUDIO DIGITAL OUT

setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or
[BITSTREAM].

yChange Audio DRC setting on Player setup menu to [OFF] state.

Trademarks and
licenses

Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0 Channel is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.

Bluetooth® wireless technology is a system which
allows radio contact between electronic devices
within a max. range of 10 meters.

Connecting individual devices under Bluetooth®
wireless technology does not incur any charges.
A mobile phone with Bluetooth® wireless
technology can be operated via the Cascade if
the connection was made via Bluetooth® wireless
technology.

The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.

Other trademarks and trade names are those of
their respective owners.

Appendix 27

5

Appendix

HDMI, the HDMI logo and High-Denition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.

Appendix28

Specifications

General

AC adapter requirements AC 100 - 240 V, 50 / 60 Hz

Power consumption DC 25V 0 2A

Dimensions (W x H x D) (1038 x 35.4 x 75) mm

Net Weight (Approx.) 2.3 kg

Operating temperature 41 °F to 95 °F (5 °C to 35 °C)

Operating humidity 5 % to 90 %

Bus Power Supply DC 5 V 0 500 mA

Input/Output

OPTICAL IN 3 V (p-p), Optical jack x 1

PORT. IN 0.5 Vrms (3.5 mm stereo jack)

HDMI IN 19 Pin (Type A, HDMI™ connector) x 1

HDMI OUT 19 Pin (Type A, HDMI™ connector) x 1

Amplier

Stereo mode 80 W + 80 W (4 Ω at 1 kHz)

5

Appendix

Wireless subwoofer

Power requirements AC 200 - 240 V, 50 - 60 Hz

Power consumption 35 W

Type 1 Way 1 Speaker

Impedance Rated 3 Ω

Output Power 150 W

Max. Output Power 300 W

Net Dimensions (W x H x D) (221 x 351.5 x 281) mm

Net Weight 7.32 kg

Designs and specications are subject to change without prior notice.

Maintenance

Handling the unit

When shipping the unit

Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.

Keeping the exterior surfaces clean

yDo not use volatile liquids such as insecticide

spray near the unit.

yWiping with strong pressure may damage the

surface.

yDo not leave rubber or plastic products in

contact with the unit for a long period of time.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.

Appendix 29

5

Appendix