LG MP42PZ45V, RP-BA50, RU42PZ90, P42W24BX Service manual & schematics

PLASMA TV
SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : RF-03GA

MODEL : RU-42PZ90

website:http://biz.LGservice.com

e-mail:http://www.LGEservice.com/techsup.html

Sep., 2003

Printed in KoreaP/NO : 3828VD0129Z

- 2 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance

An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.

It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the specified.

When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument's
exposed
METALLIC PARTS

Good Earth Ground
such as WATER PIPE,
CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 3 -

DESCRIPTION OF CONTROLS...........................................4

EXTERNAL CONTROL DEVICE SETUP..............................7

IR CODE(NEC FORMAT) ...................................................13

ADJUSTMENT INSTRUCTIONS ........................................15

BLOCK DIAGRAMS............................................................18

EXPLODED VIEW...............................................................20

EXPLODED VIEW PARTS LIST.........................................21

REPLACEMENT PARTS LIST............................................22

SCHEMATIC DIAGRAM..........................................................

PRINTED CIRCUIT BOARD ...................................................

TABLE OF CONTENTS

- 4 -

Controls

Controls

VOL.MENU

INPUT

SELECT

ON/OFF

Main Power Button

INPUT SELECT Button

VOLUME (FF,GG) Buttons

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Plasma display is turned on

Remote Control Sensor

MENU Button

EE, DD

Buttons

Front Panel Controls

Front Panel Controls

DESCRIPTION OF CONTROLS

- 5 -

Connection Options

Connection Options

(MONO)

R

AUDIO

VIDEO

L

AV(EXPANDED) INPUT

R

AUDIO

VIDEO

L

AV OUTPUT

EXPANDED OUTPUT

REMOTE
CONTROL

ANT INDC IN

(DC 12V)

+75 Ω

R

( )( )

( )

( )

L

EXPANDED

INPUT

VIDEO
INPUT

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

Y PBP

R

(MONO)

R

AUDIO

L

R

AUDIO

L

S-VIDEO

AC INPUT

AUDIO INPUT

AUDIO INPUT

AUDIO INPUT

REMOTE
CONTROL

COMPONENT INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

6

Tuner Connections

1. ANTENNA INPUT PORT

Connection for an over-the-air or terrestrial antenna, your
cable TV wire, or cable box.

2. AV (EXPANDED) INPUT

Connection for audio/video out from external equipment.

3. AV OUTPUT

Connection for a second TV or monitor.

4. REMOTE CONTROL

Connect your wired remote control to the remote control port
on the PDP Tuner.

5. EXPANDED OUTPUT

Connect the Plasma display to the PDP Tuner with the tuner
box cable.

Plasma Display Connections

6. EXTERNAL SPEAKER (8 ohm output)

Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker

Stand’ manual.

7. RS-232C INPUT (CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

8. DVI (Digital Visual Interface) INPUT/

RGB INPUT/AUDIO INPUT JACKS

Connect the Plasma display output connector from a PC to
the appropriate input port.

9. RGB OUTPUT PORT

You can watch the RGB signal on another monitor, connect
RGB OUTPUT to another monitor’s PC input port.

10. EXPANDED INPUT

Connect the Plasma display to the PDP Tuner with the
tuner box cable supplied.

11. COMPONENT INPUT/AUDIO INPUT JACKS

Connect a component video device to these jacks.

12. REMOTE CONTROL

Connect your wired remote control to the remote control
port on the Plasma display.

13. S-VIDEO INPUTS

Connect S-Video out from an S-VIDEO VCR to the S­VIDEO input.

AUDIO/VIDEO INPUT JACKS

Connect audio/video out from external equipment to these
jacks.

14. POWER CORD SOCKET

This Plasma display operates on an AC power. The voltage
is indicated on the Specifications page. Never attempt to
operate the Plasma display on DC power.

Back Connection Panel

Back Connection Panel

7 9 10 128 13 1411

1 2 3 4 5

DESCRIPTION OF CONTROLS

- 6 -

Remote Control Key Functions

Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the Plasma display.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again
as necessary.

1 2 3

4 5 6

7 8

0

9

POWER

MULTIMEDIA INPUT SELECT

APC DASP

ARC SLEEP

PIP

DW

SWAP

MENU MUTE

ENTER

VOL

POWER

STOP

FF

REC

PLAY

REW

P/STILL

WIN.SIZE

WIN.POSITION

FAV CH

CAPTION

A.PROG PIP CH

PIP CH

ZOOM +

MTS

ZOOM -

SPLIT ZOOM

MEMORY/ERASE

VOL

CH

CH

PIP INPUT

POWER

Switches the Plasma display

between ON and STANDBY.

MULTIMEDIA

Selects source:

Component, RGB, or DVI

mode.

APC

Adjusts the factory preset picture

according to the room.

ARC

Changes the picture format.

PIP

Switches the sub picture on and off.

SWAP

Exchanges main and sub picture

images.

MENU

Displays on screen menus.

Exits the current menu.

Memorizes menu changes.

ENTER
CH

DD / EE

(Channel button)

Selects the desired channel.
Selects menu options.

VOL

FF / GG

(Volume button)

Increases/decreases sound level.
Adjusts menu settings.

INPUT SELECT

Selects source:

TV, Video (Exp.),
Video, S-Video, Component, RGB, or
DVI mode.

DASP

Selects the sound appropriate to
your viewing program character:

Flat, Music, Movie, Sports, or User.

SLEEP

Sets the sleep timer.

PIP INPUT

Selects the input source mode for
the sub picture.

MUTE

Switches the sound on or off.

ZOOM-/ZOOM+

Enlarges or reduces the main picture
size.

DW (Double Window)

Selects Double Window mode.

PIP CH

DD / EE

Selects the channel for the sub
picture.

MTS

Selects the MTS sound: Mono, Stereo,
or SAP.

FAV CH

Selects favorite channels.

WIN. SIZE

Adjusts the sub picture size.

WIN.POSITION

Moves the sub picture on the screen.

NUMBER buttons

AUTO PROGRAM

Searches for available channels, see

page 18.

MEMORY/ERASE

Memorizes or erases selected

channel.

CAPTION

Selects CAPTION mode.

VCR BUTTONS

Control some LG video cassette

recorders.

SPLIT ZOOM

Enlarges the picture.

DESCRIPTION OF CONTROLS

- 7 -

No. Pin name
1 No connection
2 RXD (Receive data)
3 TXD (Transmit data)
4 DTR (DTE side ready)
5 GND
6 DSR (DCE side ready)
7 RTS (Ready to send)
8 CTS (Clear to send)
9 No Connection

1
5

6

9

2
3
5
4
6
7
8

RXD
TXD
GND
DTR
DSR
RTS
CTS

TXD

RXD
GND
DSR

DTR

CTS

RTS

PC

7-Wire Configurations

(Standard RS-232C cable)

D-Sub 9

3
2
5
6
4
8
7

PDP

D-Sub 9

2
3
5
4
6
7
8

RXD
TXD
GND
DTR
DSR
RTS
CTS

TXD
RXD

GND

DTR

DSR

RTS
CTS

PC

3-Wire Configurations

(Not standard)

D-Sub 9

3
2
5
4
6
7
8

PDP

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the Plasma display’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Plasma display back panel.

- RS-232C connection cables are not supplied with the Plasma display.

TType of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

RS-232C Configurations

RS-232C Setup

RS-232C Setup

R

( )( )

( )

( )

L

EXPANDED

INPUT

VIDEO
INPUT

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

Y PBP

R

(MONO)

R

AUDIO

L

R

AUDIO

L

S-VIDEO

AC INPUT

AUDIO INPUT

AUDIO INPUT

AUDIO INPUT

REMOTE
CONTROL

DVI INPUT RGB INPUT

RGB OUTPUT

COMPONENT INPUT

(MONO)

R

AUDIO

VIDEO

L

AV(EXPANDED) INPUT

R

AUDIO

VIDEO

L

AV OUTPUT

EXPANDED OUTPUT

REMOTE
CONTROL

ANT INDC IN

(DC 12V)

+75 Ω

PC

EXTERNAL CONTROL DEVICE SETUP

- 8 -

Set ID

Set ID

- Use this function to specify a plasma display ID number.

• Baud rate : 115200 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Communication Parameters

Communication Parameters

1. Press the MENU button and then use

DD /EE

button to select the SPECIAL menu.

2. Press the GGbutton and then use

DD /EE

button to select Set ID.

3. Press the GGbutton and then use F / G button to adjust Set ID to choose the desired
plasma display ID number. The adjustment range of Set ID is 1 ~ 99.

4. Press the ENTER button to save.

SPECIAL

Prev.

Language
Key lock
ISM Method
Low power

Set ID

GG

Caption / Text
Captions
OSD Rotate

SPECIAL

MENU

1

Transmission

*

[Command 1]: First command to control PDP set. (j or k)

*

[Command 2]: Second command to control PDP set.

*

[Set ID]: You can adjust the set ID to choose desired plasma

display ID number in Special menu. Adjustment
range is 1 ~ 99. When selecting Set ID ‘0’, every
connected PDP set is controlled. Set ID is indicat­ed as decimal (1~99) on menu and as Hexa deci­mal (0x0~0x63) on transmission/receiving proto­col.

*

[DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

*

[Cr]: Carriage Return

ASCII code ‘0x0D’

*

[ ]: ASCII code ‘space (0x20)’

[Command1][Command2][ ][Set ID][ ][Data][Cr]

TTransmission / Receiving Protocol

ransmission / Receiving Protocol

OK Acknowledgement

* The Plasma display transmits ACK (acknowledgement)

based on this format when receiving normal data. At this
time, if the data is data read mode, it indicates present
status data. If the data is data write mode, it returns the
data of the PC computer.

[Command2][ ][Set ID][ ][OK][Data][x]

Error Acknowledgement

* The Plasma display transmits ACK (acknowledgement)

based on this format when receiving abnormal data from
non-viable functions or communication errors.

[Command2][ ][Set ID][ ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function
3: Wait more time

01. Power k a 0 ~ 1

02. Input Select k b 0 ~ 6

03. Aspect Ratio k c 0 ~ 3

04. Screen Mute k d 0 ~ 1

05. Volume Mute k e 0 ~ 1

06. Volume Control k f 0 ~ 64

07. Contrast k g 0 ~ 64

08. Brightness k h 0 ~ 64

09. Color k i 0 ~ 64

10. Tint k j 0 ~ 64

11. Sharpness k k 0 ~ 64

12. OSD Select k l 0 ~ 1

13.

Remote Control Lock Mode

k m 0 ~ 1

14. PIP/Twin k n 0 ~ 3

15. PIP Size k o 0 ~ 1

16. Split Zoom k p 21 ~99

17. PIP Position k q 0 ~ 3

18. Treble k r 0 ~ 64

19. Bass k s 0 ~ 64

20. Balance k t 0 ~ 64

21. Color Temperature k u 0 ~ 3

22. Red Adjustment k v 0 ~ C8

23. Green Adjustment k w 0 ~ C8

24. Blue Adjustment k $ 0 ~ C8

25. PIP Input Source k y 0 ~ 6

26. Abnormal Status k z 0 ~ a

27. ISM Method j p 0 ~ 3

28. Low Power j q 0 ~ 1

29. Orbiter Time Setting j r 1 ~ FE

30. Orbiter Pixel Setting j s 0 ~9

31. Picture Size Setting j t 0 ~64
for Double Window mode

32. Auto Configure j u 1

COMMAND 1 COMMAND 2 DATA

(Hexadecimal)

• When setting the 27 ~ 32, a menu doesn’t display on

screen.

Command Reference List

Command Reference List

EXTERNAL CONTROL DEVICE SETUP

- 9 -

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the Plasma display.

You can also select an input source using the INPUT
SELECT button on the Plasma display's remote control.

Transmission

Data 0 : RGB

1 : Component
2 : Video
3 : S-Video

4 : DVI
5 : TV
6 : Video (Exp.)

[k][b][ ][Set ID][ ][Data][Cr]

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

01. Power (Command2:a)

G To control Power On/Off of the Plasma display.

Transmission

Data 0 : Power Off 1 : Power On

[k][a][ ][Set ID][ ][Data][Cr]

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

G To show Power On/Off.

Transmission

[k][a][ ][Set ID][ ][FF][Cr]

Acknowledgement

Data 0 : Power Off 1 : Power On

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback
presents status about each function.

[a][ ][Set ID][ ][OK][Data][x]

*

Real data mapping 1

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

64 : Step 100

05. Volume Mute (Command2:e)

G To control volume mute on/off.

You can also adjust mute using the MUTE button on
remote control.

Transmission

Data 0 : Volume mute on (Volume off)

1 : Volume mute off (Volume on)

[k][e][ ][Set ID][ ][Data][Cr]

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust the screen format.

You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.

Transmission

Data 0 : Wide screen (16:9)

1 : Normal screen (4:3)
2 : Full screen (Zoom)
3 : Horizon

[k][c][ ][Set ID][ ][Data][Cr]

Acknowledgement

* Using the PC input, you select either 16:9 or 4:3 screen

aspect ratio.

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command2:d)

G To select screen mute on/off.

Transmission

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

[k][d][ ][Set ID][ ][Data][Cr]

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G To adjust volume.

You can also adjust volume with the volume buttons
on remote control.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’ as shown below.

[k][f][ ][Set ID][ ][Data][Cr]

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G To adjust screen contrast.

You can also adjust contrast in the Picture menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’ as shown below.

[k][g][ ][Set ID][ ][Data][Cr]

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

EXTERNAL CONTROL DEVICE SETUP

- 10 -

09. Color (Command2:i)

G To adjust the screen color.

You can also adjust color in the Video menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][i][ ][Set ID][ ][Data][Cr]

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G To adjust the screen tint.

You can also adjust tint in the Video menu.

Transmission

Data Red : 0 ~ Green : 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][j][ ][Set ID][ ][Data][Cr]

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h)

G To adjust screen brightness.

You can also adjust brightness in the Video menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][h][ ][Set ID][ ][Data][Cr]

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)

G To lock the remote control and the front panel controls on

the plasma display.

Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Lock off 1: Lock on

• If you’re not using the remote control, use this mode.

When main power is on/off, remote control lock is released.

[m][ ][Set ID][ ][OK][Data][x]

14. PIP / DW (Command2:n)

G To control the PIP (Picture-in-Picture)/DW (Double Window).

You can also control the PIP/DW using the PIPor DW but­ton on the remote control or in the Special menu.

Transmission

Data 0: PIP/DW off

1: PIP

2: DW1
3: DW2

[k][n][ ][Set ID][ ][Data][Cr]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

G To adjust the screen sharpness.

You can also adjust sharpness in the Video menu.

Transmission

11. Sharpness (Command2:k)

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][k][ ][Set ID][ ][Data][Cr]

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G To select OSD (On Screen Display) on/off.

Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: OSD off 1: OSD on

[l][ ][Set ID][ ][OK][Data][x]

15. PIP Size (Command2:o)

G To select the PIP picture format.

You can also select the PIP picture format using WIN.SIZE
on the remote control.

Transmission

[k][o][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: 4:3 1: 16:9

[o][ ][Set ID][ ][OK][Data][x]

16. Split Zoom (Command2:p)

G To operate split zoom function and select the split

zoom section number.

Transmission

Data Min: 21 ~ Max: 99

ex. Data 21: Selection 1 of 2 split zoom.

• Refer to ‘Real data mapping 2’.

[k][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

*

Real data mapping 2

21: Selection 1 of 2 split zoom
24: Selection 4 of 2 split zoom
41: Selection 1 of 4 split zoom
42: Selection 2 of 4 split zoom
44: Selection 4 of 4 split zoom
45: Selection 5 of 4 split zoom
91: Selection 1 of 9 split zoom

99: Selection 9 of 9 split zoom

EXTERNAL CONTROL DEVICE SETUP

- 11 -

22. Red Adjustment (Command2:v)

G To adjust red in color temperature.

Transmission

Data Min: 0 ~ Max: C8

• Refer to ‘Real data mapping3’ as shown below.

[k][v][ ][Set ID][ ][Data][Cr]

Acknowledgement

[v][ ][Set ID][ ][OK][Data][x]

23. Green Adjustment (Command2:w)

G To adjust green in color temperature.

Transmission

Data Min: 0 ~ Max: C8

• Refer to ‘Real data mapping3’ as shown below.

[k][w][ ][Set ID][ ][Data][Cr]

Acknowledgement

[w][ ][Set ID][ ][OK][Data][x]

24. Blue Adjustment (Command2:$)

G To adjust blue in color temperature.

Transmission

Data Min: 0 ~ Max: C8

• Refer to ‘Real data mapping3’ as shown below.

[k][$][ ][Set ID][ ][Data][Cr]

Acknowledgement

[$][ ][Set ID][ ][OK][Data][x]

21. Color Temperature (Command2:u)

G To adjust color temperature.

You can also adjust ACC in the Video menu.

Transmission

Data 0: Normal 1: Cool 2: Warm 3: User

[k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

20. Balance (Command2:t)

G To adjust balance.

You can also adjust balance in the Audio menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

18. Treble (Command2:r)

G To adjust treble.

You can also adjust treble in the Audio menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

19. Bass (Command2:s)

G To adjust bass.

You can also adjust bass in the Audio menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 34.

[k][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

17. PIP Position (Command2:q)

G To select sub picture position for PIP.

You can also adjust the sub picture position using
WIN.POSITION on the remote control or in the Special menu.

Transmission

Data 0: Right down on screen

1: Left down on screen
2: Left up on screen
3: Right up on screen

[k][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

*

Real data mapping 3

0 : -20
5 : -19
A : -18

5F: -1
64: 0
69: +1

C3: +19
C8: +20

EXTERNAL CONTROL DEVICE SETUP

- 12 -

EXTERNAL CONTROL DEVICE SETUP

27. ISM Method (Command2:p)

G To avoid having a fixed image remain on screen.

Transmission

Data 0: Normal

1: White wash

2: Orbiter
3: Inversion

[j][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

28. Low Power (Command2:q)

G To control the low power function on/off.

Transmission

Data 0: Low power off

1: Low power on

[j][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

29. Orbiter Time Setting (Command2:r)

G To adjust orbiter operation time term.

Transmission

Data Min: 1 ~ Max: FE

• Refer to ‘Real data mapping1’. See page 34.

[j][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

30. Orbiter Pixel Setting (Command2:s)

G To adjust pixel number in orbiter function.

Transmission

Data Min: 0 ~ Max: 9

[j][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

31. Picture Size Setting for Double Window
mode (Command2:t)

G To adjust main window size in Double Window mode.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping1’. See page 30.

[j][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

32. Auto Configure (Command2:u)

G To adjust picture position and minimize image shaking

automatically. It works only in RGB (PC) mode.

Transmission

Data 1: To set

[j][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

25. PIP Input Select (Command2:y)

G To select input source for sub picture in PIP mode.

Transmission

Data 0 : RGB

1 : Component
2 : Video
3 : S-Video

4 : DVI
5 : TV
6 : Video (Exp.)

[k][y][ ][Set ID][ ][Data][Cr]

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

26. Abnormal State (Command2:z)

G To recognize an abnormal state.

Transmission

Data 0: Normal (Power on and signal exist)

1: No signal (Power on)
2: Turn the monitor off by remote control
3: Turn the monitor off by sleep time function
4: Turn the monitor off by RS-232C function
5: 5V down
6: AC down
7: Turn the monitor off by Fan Alarm function
8: Turn the monitor off by off time function
9: Turn the monitor off by auto off function
a: Turn the monitor off by AV board detect

Data FF:Read

[k][z][ ][Set ID][ ][FF][Cr]

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

- 13 -

IR Code(NEC Format)

G Connect your wired remote control to the Remote port on the Plasma display.

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

G Configuration of frame

G Repeat code

G Lead code

• 1st frame

Low
custom code

Lead
code

High
custom code

Data code

Data code

T

C

Tf

T1

C0

Carrier frequency

F

CAR = 1/TC = fOSC/12

Duty ratio = T1/T

C = 1/3

• Repeat frame

C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G Bit description

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

• Bit “0”

Tf Tf

Tf=108ms @455KHz

0.56 ms 0.56 ms

1.12 ms

• Bit “1”

2.24 ms

How to Connect

How to Connect

Remote Control IR Code (NEC Format)

Remote Control IR Code (NEC Format)

- 14 -

IR Code(NEC Format)

UP (D)
DOWN (

E

)

VOL+ (

G)

VOL- (

F)

POWER ON/OFF
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
INPUT SELECT
MULTIMEDIA
RGB
DVI
Component
Video

S-video
TV
Video (Exp.)
SLEEP
ENTER (

ç)

MENU
DASP

APC

PIP
PIP INPUT
SWAP
PIP ARC
TWIN PICTURE
ZOOM +
ZOOM ­Window Size
Window Position
Split Zoom

ARC
ARC (4:3)
ARC (16:9)
ARC (Zoom)
AUTO CONFIG
AUTO PROGRAM

MEMORY/ERASE
FAVORITE CH
CAPTION
MTS
PIP UP (

D

)

PIP DOWN (

E

)

00H
01H
02H
03H
08H
C4H
C5H
09H
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
0BH
98H
D5H
C6H
BFH
5AH
D8H
D6H
D0H
0EH
44H
43H
52H
4DH
60H
61H
63H
64H
6BH
40H
41H
69H
6AH
7BH
79H
76H
77H
AFH
99H
54H
55H
1EH
39H
0AH
71H
72H

R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Video/S-video/Component/RGB/DVI)
R/C Button (Component/RGB/DVI)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input DVI Selection)
Discrete IR Code (Input Component Selection)
Discrete IR Code (Input Video Selection)
Discrete IR Code (Input S-video Selection)
Discrete IR Code (Input TV Selection)
Discrete IR Code (Input Expanded Video Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (PIP/TWIN picture Exchange)
R/C Button (4:3/16:9)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (4:3/16:9/Zoom mode Selection)
Discrete (Only 4:3 mode)
Discrete (Only 16:9 mode)
Discrete (Only Zoom mode)
Discrete IR Code
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button

Code (Hexa) Function Note

1. Application

These instructions apply to the RF-03GA.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test instruments.
(2) Adjustments must be performed in the correct order.
(3) The adjustments must be performed in conditions between

68° and 86°F with 55-75% relative humidity.
(4) The input voltage of the receiver must keep at 100~240V,

50/60Hz during adjustment(s).
(5) The receiver must be operated for at least 15 minutes prior

to the adjustment(s).

1) The receiver must be operated receiving 100% white
pattern, prior to adjustment(s).
(White condition in HEAT-RUN mode)

2) Enter into HEAT-RUN mode

- Press the POWER ON KEY on Adjustment R/C.

- OSD display HEAT-RUN WHITE and screen display

100% full WHITE PATTERN.

[ Set is activated HEAT-RUN without signal generator in

this mode.

[ Single color pattern of HEAT-RUN mode uses to check

PANEL. (RED/BLUE/GREEN)

[Caution]

If you turn on a still screen more than 20 minutes
(such as Cross Hatch Pattern, Digital Pattern), an
afterimage may be occur in the black level part of the
screen. (Image Burn)

O

Data values, adjusted in the board, are valid until the VSC
Board is dissued and must be protected. For the protection of
data, Micom does not permit any more adjustments after
completion.

O

In case of re-adjustment, operate First Value Setting.

Each PCB Assy must be checked prior to installation.
(Especially, be careful Power PCB Assy which can cause
damage to PDP Module.)

3. POWER PCB Assy Voltage
Adjustments

(Va, Vs Voltage Adjustments)

3-1 Test Equipment : Digital Multi-Meter (DMM)

3-2 Connection Diagram for Measuring

Refer to Fig 1.

3-3 Adjustment Method

(1) Va Adjustment

1) Select White Mode of HEAT RUN or receive a 100%
Full White Pattern with the Video/RGB from a Pattern
Generator.

2) Connect the + terminal of the DMM to Va pin of P805
and the - terminal of the DMM to GND pin of P805.

3) Adjust RV601 until the reading of Va on the DMM is the
same as Va voltage on label of panel Right/Top.
(Deviation : ±0.5V)

(2) Vs adjustment

1) Connect the + terminal of the DMM to Vs pin of P805
and the - terminal of the DMM to GND pin of P805.

2) Adjust RV401 until the reading of Vs on the DMM is the
same as Vs voltage on label of panel Right/Top.
(Deviation : ±0.5V)

4. Auto ADC Adjustments

4-1 RGB Auto Offset & Gain Adjustment

(1) Input Half Black/White (255 Gray) signal from a Pattern

Generator into the RGB Input.
(XGA 1024*768 60Hz)

- 15 -

ADJUSTMENT INSTRUCTIONS

DMM

+ -

RV401
Vs ADJ

RV601
Va ADJ

P804

P805

Vs

NC

Va

GND

DMM

+ --

RV401
Vs ADJ

RV601
Va ADJ

P804

P805

RV401
Vs ADJ

RV601
Va ADJ

P804

P805

Vs

NC

Va

GND

Vs

NC

Va

GND

<Fig 1> Connection Diagram of Power Adjustments

- 16 -

(2) Press POWER ON KEY on the Adjustment R/C and select

RGB Cut.
(3) Press Vol. + key and operate TO SET(Black).
(4) Original Half Black/White(255 Gray) screen will be

presented about 5~10 seconds later. And Cursor moves

with a lower part Y-cut.

This case RGB Auto Offset, MAX Gain adjustment will be

completed.

4-2 Component Auto Offset & Gain

Adjustment

(Y, Pb, Pr Adjustment)

(1) Input Half Black/White (255 Gray) signal from a Pattern

Generator into the component Input. (1280*720p 60Hz)

(2) Press Vol. + key and operate To SET from the condition

where the cursor moves with the Y-cut.
(3) Original Half White(255 Gray) screen will be presented

about 5~10 seconds later. And Cursor moves with a lower

part Pb-cut.

This case Component Y-offset & Gain adjustment will be

completed.
(4) After adjustment of item (3), receive Half Blue(127 level)

signal for Pb-offset adjustment.

(5) Press Vol. + key and operate To SET for Pb-offset

adjustment.
(6) Original Half Blue(127 level) screen will be presented

about 5~10 seconds later. And Cursor moves with a lower

part Pr-cut.

This case Component Pb-offset & Gain adjustment will be

completed.
(7) After adjustment of item (5), receive Half Red(127 level)

signal for Pr-offset adjustment.

(8) Press Vol. + key and operate To SET for Pr-offset

adjustment.

(9) Original Half Red(127 level) screen will be presented

about 5~10 seconds later and the OK indication appears.
This case Component Auto offset & Gain adjustment will
be completed.

O

You can check whether circuit adjustment is correct or not,
below. (Item 4-1)

(1) Display RGB to the Main picture, CVBS to the Sub picture

in TWIN PICTURE mode. (DOUBLE WINDOW)

(2) To check the Offset, input Full Black (0 gray) signal into

CVBS and RGB input part at the same time in the Pattern
Generator.

(3) To check the MAX-Gain, input Full White (255 gray) signal

into CVBS and RGB input part at the same time in the
Pattern Generator.

(4) Visually compare Black and White Levels. If there is no

Level difference, then the adjustment is correct.

O

You can check whether circuit adjustment is correct or not,

below. (Item 4-2)

(1) Display Component to the Main picture, CVBS to the Sub

picture in TWIN PICTURE mode. (DOUBLE WINDOW)

(2) Using HD STB(SK-010T) or equal equipment input Digital

Pattern into CVBS and Component input part.
(720p or 1080i)

(3) Visually compare Black and White Levels of Main and Sub

screen. If there is no Level difference, then the adjustment
is correct.

ADJUSTMENT INSTRUCTIONS

White : 255 Gray level

White : 255 Gray level

- 17 -

5. Adjustment of White Balance

5-1. Required Equipment

Color analyzer (CA-100 or similar product)

5-2. Connection Diagram of Equipment for

Measuring

(Manual Adjustment)

5-3. Adjustment of White Balance

O

Operate the Zero-calibration of the CA-100, then apply the

sensor to the PDP display surface.

O

Manual adjustment is also possible with the following sequence.

(1) Select WHITE PATTERN of HEAT RUN mode by pressing

POWER ON KEY on the Adjustment R/C, then operate the
HEAT RUN for at least 15 minutes.

(2) Supply 216Gray, 50% size length and breadth signal to RGB

input. (Refer to Fig 2)

(3) W/B adjustment must be adjusted only High Light and then

save the adjustment value with

Y Key.

(4) To adjust High Light, apply sensor to 216 Gray Level (or 105-

115 Cd/m

2

) Pattern, press ADJ Key on Adjustment R/C and
press T, U on Adjustment R/C to select R-L or G-L, press
VOL +, - Key(s) to adjustuntil color coordination becomes as
below.
X: 0.280±0.003, Y: 0.290±0.003
Color temperature: 10,000°K±500°K

(5) Exit adjustment mode using Y Key.

6. DDC Data Input

6-1. Required Test Equipment

(1) A jig for adjusting PC, DDC. (PC serial to D-sub.

Connection equipment)
(2) S/W for writing DDC(EDID data write & read)
(3) D-Sub 15P cable, D-Sub to DVI Connector (DVI-D)

6-2. Setting of Device

6-3. Preparation for Adjustments

(1) Set devices as above and turn the PC, JIG on.
(2) Open S/W for writing DDC (EDID data write & read).

(operated in DOS mode)

6-4. Sequence of Adjustments

(1) DDC Data Input for Analog-RGB

1) Place the set on the table and turn the power on.

2) Connect PC Serial to D-sub 15P Cable of JIG for DDC
Adjustment to RGB terminal (D-Sub 15Pin).

3) Open S/W for DDC record and select DDC Data for
Analog RGB in Model Menu.

4) Operate EDID Write command.

5) Operate EDID Read command and check whether
Check Sum is OK.

6) If Check Sum is NG, repeat 3) ~ 4).

7) If Check Sum is OK, DDC Data for Analog-RGB input is
completed.

(2) DDC Data input for Digital-RGB

1) Connect PC Serial to DVI Cable(DVI-D) of JIG for DDC
Adjustment to DVI terminal.

2) Operate S/W for DDC record and select DDC Data for
Digital RGB in Model Menu.

3) Operate EDID Write command.

4) Operate EDID Read command and check whether
Check Sum is OK.

5) If Check Sum is NG, repeat 3) ~ 4).

6) If Check Sum is OK, DDC Data for Digital-RGB input is
completed.

ADJUSTMENT INSTRUCTIONS

R-H 216R-H 216
G-H 216G-H 216

Window

VG828, MSPG-2100
or MSTG-5200

High Light

216 Gray Level

<Fig 2> Connection Diagram of Manual Adjustment

RGB Signal Input

PDP MONITOR

- 18 -

BLOCK DIAGRAM

- 19 -

BLOCK DIAGRAM

- 20 -

EXPLODED VIEW

200

203

205

202

204

206

530

401

540

541

520

560

550

210

570

220

521

551

553

552

201

580

301

303

302

300

305

400

<Tuner>

720

710

700

- 21 -

EXPLODED VIEW PARTS LIST

200 6348Q-E036A PDP,42 16:9 852*480 PDP42V50000(KK MODEL), FOR INTERCOMPANY
201 6871QDH051A PCB ASSEMBLY,DISPLAY YDRV ASSY 42SD5_YDRV_TOP_TI_4LAYER
202 6871QDH052A PCB ASSEMBLY,DISPLAY YDRV ASSY 42SD5_YDRV_BTM_TI_4LAYER
203 6871QCH025A PCB ASSEMBLY,DISPLAY CTRL ASSY 42SD5 CTRL BD(LPCMC1121)
204 6871QYH027A PCB ASSEMBLY,DISPLAY YSUS ASSY 42SD5_SEPERATED_YSUS
205 6871QRH034A PCB ASSEMBLY,DISPLAY XRRT ASSY 42SD5_XR_SEPERATE(4 LAYER)
206 6871QZH030A PCB ASSEMBLY,DISPLAY ZSUS ASSY 42SD5(YZ SEPARATE)
210 4980V00240A SUPPORTER,VERTICAL EGI FD-42X3
220 4980V00240B SUPPORTER,VERTICAL EGI MN-42PZ10
300 3091V00516A CABINET ASSEMBLY,MZ-42PZ90 NON NON LG BRAND DARK SILVER
301 4980V00266A SUPPORTER ASSY,NON FILTER TOP MN-42PZ10
302 4980V00267A SUPPORTER ASSY,NON FILTER BOTTOM
303 4980V00268A SUPPORTER ASSY,NON FILTER SIDE
305 3790V00709A FILTER(MECH),MN-42PZ40S LGM42-01 MITSUI GLASS
400 3809V00245X BACK COVER ASSEMBLY,MZ-42PZ90 NON PIGGY BLACK
401 3300V00096R PLATE,A/V AL 675.2*95.8*1.2 MZ-42PZ90
520 6871VMMP39A PCB ASSEMBLY,MAIN RF03GA MU-42PZ44 VSC
521 4980V00793A SUPPORTER,VSC EGI MZ-42PZ44
530 6871VSMU44B PCB ASSEMBLY,SUB CONT RF03FA 90 TOOL
540 6871VSMV04B PCB ASSEMBLY,SUB PSW RF03FA 90 TOOL
541 5020V00457A BUTTON,POWER FD-36X3
550 6871VSMU98A PCB ASSEMBLY,SUB A/V RF03GA FIX B/D
551 4980V00465D SUPPORTER,AV INTERFACE SBHG MU-42PZ41
552 4980V00748C SUPPORTER,AV INTERFACE AL MN-42PZ44 ASSY
553 4814V00309B SHIELD,COVER RJ-42PZ40 RF02KC AL AC SOCKET
560 6871VSMU45A PCB ASSEMBLY,SUB SPK RF03GA MU-42PZ44
570 6871VSMU46A PCB ASSEMBLY,SUB A/V RF03GA MU-42PZ44 PACK ASSY
580 3501V00148A BOARD ASSEMBLY,POWER MU42PZ44 RF03GA SRX-74 SONY 42KK
700 3110V00237F CASE,TUNER RT-BA50 EGI BOTTOM ASSY
710 6871VSMX52A PCB ASSEMBLY,SUB VIDEO RF03GA PIGGY BACK(RU)
720 3110V00242F CASE,TUNER RT-BA50 EGI TOP ASSY

No.

Part No.

Description

- 22 -

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

IC704
IC740
IC741
IC742
IC743
IC744
IC746
IC747
IC748
IC749
IC750
IC751
IC802
IC850
IC851
IC853
IC857
IC858
IC859
IC901
IC902
IC903
IC904
IC917

IC008
IC009
IC203
IC204
Q001
Q001
Q001
Q001
Q002
Q002
Q002
Q002
Q003
Q003
Q003
Q004
Q004
Q005
Q006
Q007
Q008
Q009

0IMCRAL006A

0IMCRPH017A

0IMCRFA013A
0IMCRFA013A

0ITI745740M
0IMCRPH017A
0IMCRPH015A
0IMCRPH016A
0IMCRPH014A

0IKE702700D
0IDS232000A
0IPH858400A

0ISA428200A
0IMCRSJ001A
0IPRPML001A

0IMCRRH001A
0IMCRRH001A
0IMCRSH001A
0IMCRSH001A
0IMCRMN014A

0IKE780800J

0IMCRSH001A

0IKE704200J

0IFA742530B

0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA

AT24C16AN10SI2.7 8P SOIC R/TP EEPROM
74LVC574APW 20P SOT3601
74LCX244MTC 20P
74LCX244MTC 20P
SN74HC574NSR 14P
74LVC574APW 20P SOT3601
74LVC32AD 14P SOT1081
74LVC139D 16P SOT1091
74LV132D 14P SOT1081
KIA7027AF 3, SOT89 TP RESET IC 2.7V
DS232AS 16P,SOP TP RS232
PCF8584T 20P IIC BUS CONTROLLER
LA4282 12S 2CHX10W AUDIO AMP
SC1565IST1.8 3P SOT223 TP REGULATOR
MIC39100 3P SOT223
BA033FP 3PSOP
BA033FP 3PSOP
PQ05DZ1U SHARP 5
PQ05DZ1U SHARP 5
MSP3440G QA B8 V3 80 SOUND IC
KIA7808API 3 ST REGULATOR
PQ05DZ1U SHARP 5
KIA7042AF SOT89 TP 4.2V
74ACT253SC 16PSOIC

BSS83
BSS83
BSS83
BSS83
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC

LOCA. NO PART NO DESCRIPTION

IC001
IC001
IC002
IC002
IC003
IC005
IC006
IC101
IC102
IC103
IC104
IC1102
IC1104
IC1201
IC1202
IC1203
IC1204
IC1205
IC1401
IC1405
IC1406
IC201
IC202
IC301
IC301
IC302
IC401
IC401
IC402
IC402
IC403
IC403
IC404
IC405
IC405
IC407
IC410
IC415
IC501
IC502
IC503
IC504
IC601
IC701
IC702
IC703

0ISO208900A
0IZZVC0053A

0IAL241610B

0IMCRFA010A

0IFA753307A
0IMCRTI003A
0ISO211900A

0IAL242110A

0IAL242110A
0IMCRTI003A

0IPRPBB005A

0IMCRPH015A

0ISH122100B
0IMCRTI021A
0IMCRTI021A
0IMCRTI021A
0IMCRTI021A
0IMCRTI021A

0IIT323000E
0IMCRGN001B
0IMMRHY033A

0ISO208900A

0IMCRS5003A
0IMCRAD003A
0IMCRMN014A

0IKE704200J

0IIT323000E

0ITK118100B

0ISA715100D

0IMCRFA010A

0IFA741230A

0IMCRFA009A
0IMCRSH001A
0IMCRGN001B
0IMCRSH001A
0IMMRHY033A
0IMMRNE002A

0ISA715100D
0IMCROT001A
0IMMRHY033A
0IMMRHY033A
0IMMRHY033A

0IS5160000A
0IMCRRS001A
0IMMRSS064A
0IMMRMR006B

CXA2089Q 48QFP BK A/V SWITCH
M37136EFSP 52P BK MICOM
AT24C16A10PI2.7 8PIN
KA7809R 2P DPAK, R/TP REGULATOR IC
KA75330ZTA 3P,TO92 TP 3.3V
SN74HCT08D 16P R/TP QUADRUPLE
CXA2119M 28P VIDEO SWITCHING IC
AT24C2110SI2.5 8P,SOP TP 1K EEPROM
AT24C2110SI2.5 8P,SOP TP 1K EEPROM
SN74HCT08D 16P R/TP QUADRUPLE
OPA3692IDBQ 16PIN BUFFER AMP
74LVC32AD 14P SOT1081
PQ12RD21 4SIP ST REGULATOR
SN74LVTH541PWR 20P
SN74LVTH541PWR 20P
SN74LVTH541PWR 20P
SN74LVTH541PWR 20P
SN74LVTH541PWR 20P
VPC3230D C5 80P VIDEO PROCESSOR
FLI2310BC 208P DIGITAL VIDEO
HY57V643220C(L)T6 86P 64M
CXA2089Q 48QFP BK A/V SWITCH
SIL169 CL100 100P TMDS RX PANEL LINK
AD9888KS140 128P A/D CONVERTER IC
MSP3440G QA B8 V3 80 SOUND IC
KIA7042AF SOT89 TP 4.2V
VPC3230D C5 80P VIDEO PROCESSOR
TK11840L 8P SOT23L DCDC CONVERTER
LA7151M 10SOP R/TP AUDIO SW
KA7809R 2P DPAK
DM74LS123MX 16SOP
KA78M08RTM 2P DPAK
PQ05DZ1U SHARP 5
FLI2310BC 208P DIGITAL VIDEO
PQ05DZ1U SHARP 5
HY57V643220C(L)T6 86P 64M
UPD64083GF3BA 100 3D YC
LA7151M 10SOP R/TP AUDIO SW
REMBRANT1A 352BALL
HY57V643220C(L)T6 86P 64M
HY57V643220C(L)T6 86P 64M
HY57V643220C(L)T6 86P 64M
SII160 100 DIGITAL TRANSMITTER
R8820LV RDC 100P 16BIT
K6R4016V1DTC10 44P TSOP2400BF
MX29LV160ATTC70 48P 16M FLASH MEMORY

IC

TRANSISTOR

RUN DATE : 2003.8.28

For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;

CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic

RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible

- 23 -

LOCA. NO PART NO DESCRIPTION

Q101
Q1425
Q1473
Q200
Q201
Q201
Q202
Q203
Q204
Q204
Q205
Q205
Q206
Q206
Q207
Q207
Q208
Q209
Q211
Q251
Q252
Q253
Q301
Q302
Q303
Q304
Q305
Q401
Q410
Q411
Q412
Q413
Q414
Q415
Q416
Q417
Q418
Q419
Q420
Q421
Q422
Q423
Q424
Q450
Q471
Q472
Q473
Q474
Q475
Q476
Q477

0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA

CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC

LOCA. NO PART NO DESCRIPTION

Q478
Q479
Q720
Q721
Q722
Q723
Q724
Q725

D001
D001
D001
D002
D003
D004
D006
D011
D074
D075
D079
D100
D101
D102
D105
D106
D108
D109
D110
D111
D112
D113
D114
D115
D117
D118
D253
D254
D301
D302
D303
D304
D402
D404
D421
D422
D423
D854
D855
D857
D870

0TR104009AF
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA

0DD184009AA
0DD226239AA
0DL200000CA
0DD184009AA
0DD184009AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD100009AC
0DD100009AC
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA

CHIP KRC104S SOT23 TP KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC

KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT23
LED,SAM5670(DL2LRG) BK YGREEN
KDS184S CHIP 85V 300MA KEC TP
KDS184S CHIP 85V 300MA KEC TP
KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT23
CHIP KDS226 SOT23
RU1V(1) TP SANKEN
RU1V(1) TP SANKEN
KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
KDS184S CHIP 85V 300MA
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23

REPLACEMENT PARTS LIST

DIODE

- 24 -

LOCA. NO PART NO DESCRIPTION

D871
D872
D873
D880
D881
D882
D883
DA105
LD300
LD740
LD741
LD742
LD743
ZD100
ZD830
ZD831
ZD832

C002
C005
C006
C007
C008
C010
C012
C013
C014
C014
C015
C015
C015
C017
C018
C019
C019
C020
C020
C021
C021
C022
C022
C022
C023
C023
C023
C024
C024
C025
C025
C026

0DD226239AA
0DD226239AA
0DD226239AA
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DD226239AA
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA

0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE106SF6DC
0CE476SF6DC
0CE227VF6DC
0CE107SF6DC
0CE476SF6DC
0CE106SF6DC
0CE476SF6DC
0CE106SF6DC
0CE476SF6DC

0CN105EJ56A
0CE107SF6DC
0CE474SK6DC
0CE474SK6DC
0CE476SF6DC
0CE335SK6DC
0CE105SK6DC
0CE106SF6DC

0CE477DD618
0CE474SK6DC

0CE477DD618
0CE105SK6DC
0CE474SK6DC

0CE477DD618
0CE105SK6DC
0CE474SK6DC
0CE105SK6DC
0CE474SK6DC
0CE105SK6DC
0CE105SK6DC

CHIP KDS226 SOT23
CHIP KDS226 SOT23
CHIP KDS226 SOT23
LED,SAM2333
LED,SAM2333
LED,SAM2333
LED,SAM2333
CHIP KDS226 SOT23
LED,SAM2333
LED,SAM2333
LED,SAM2333
LED,SAM2333
LED,SAM2333
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A

47UF MVG 16V M
100UF MVG 16V M
47UF MVG 16V M
10UF MVG 16V 20%
47UF MVG 16V M
220UF MV 16V 20%
100UF MVG 16V M
47UF MVG 16V M
10UF MVG 16V 20%
47UF MVG 16V M
10UF MVG 16V 20%
47UF MVG 16V M

1.0UF 3216 35V 10%
100UF MVG 16V M

0.47UF MVG 50V M

0.47UF MVG 50V M
47UF MVG 16V M

3.3UF MVG 50V 20%
1UF MVG 50V M
10UF MVG 16V 20%
470UF STD 10V M

0.47UF MVG 50V M
470UF STD 10V M
1UF MVG 50V M

0.47UF MVG 50V M
470UF STD 10V M
1UF MVG 50V M

0.47UF MVG 50V M
1UF MVG 50V M

0.47UF MVG 50V M
1UF MVG 50V M
1UF MVG 50V M

LOCA. NO PART NO DESCRIPTION

C029
C030
C030
C031
C034
C035
C038
C039
C040
C041
C042
C042
C043
C044
C045
C045
C046
C047
C047
C048
C050
C050
C051
C052
C053
C054
C055
C056
C057
C058
C059
C077
C078
C079
C084
C109
C110
C1102
C1106
C1107
C1108
C1109
C111
C112
C113
C114
C117
C119
C121
C123
C126

0CE106SF6DC
0CE107SF6DC
0CE105SK6DC
0CE105SK6DC
0CE476SF6DC
0CE105SK6DC
0CE476SF6DC
0CE105SK6DC
0CE227VF6DC

0CE477DK618

0CE476SF6DC

0CE477DK618

0CE476SF6DC

0CE107DH618
0CE106SF6DC
0CE476SF6DC

0CQ1021N509

0CE107DH618
0CE476SF6DC

0CQ1021N509
0CE107SF6DC

0CE106DF618

0CE106DF618

0CE106DF618
0CE106SF6DC
0CE474SK6DC
0CE474SK6DC

0CE107DH618

0CQ1041N509
0CE106SF6DC

0CQ1041N509

0CE475DK618

0CE475DK618

0CE107DH618

0CE477DF618
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE227VF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477VF6DC
0CE477VF6DC
0CE477VF6DC
0CE476SF6DC

10UF MVG 16V 20%
100UF MVG 16V M
1UF MVG 50V M
1UF MVG 50V M
47UF MVG 16V M
1UF MVG 50V M
47UF MVG 16V M
1UF MVG 50V M
220UF MV 16V 20%
470UF STD 50V 20%
47UF MVG 16V M
470UF STD 50V 20%
47UF MVG 16V M
100UF STD 25V M
10UF MVG 16V 20%
47UF MVG 16V M

0.001U 100V K POLY TP
100UF STD 25V M
47UF MVG 16V M

0.001U 100V K POLY TP
100UF MVG 16V M
10UF STD 16V M
10UF STD 16V M
10UF STD 16V M
10UF MVG 16V 20%

0.47UF MVG 50V M

0.47UF MVG 50V M
100UF STD 25V M

0.1U 100V K POLY TP
10UF MVG 16V 20%

0.1U 100V K POLY TP

4.7UF STD 50V 20%

4.7UF STD 50V 20%
100UF STD 25V M
470UF STD 16V 20%
100UF MVG 16V M
100UF MVG 16V M
10UF MVG 16V 20%
220UF MV 16V 20%
1UF MVG 50V M
1UF MVG 50V M
1UF MVG 50V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
470UF MV 16V 20%
470UF MV 16V 20%
470UF MV 16V 20%
47UF MVG 16V M

REPLACEMENT PARTS LIST

CAPACITOR

- 25 -

LOCA. NO PART NO DESCRIPTION

C127
C137
C140
C1479
C1485
C1488
C1489
C1491
C1494
C1505
C1506
C1507
C1510
C201
C204
C205
C207
C208
C209
C211
C216
C221
C253
C257
C258
C259
C263
C264
C265
C266
C267
C268
C308
C309
C314
C316
C317
C318
C319
C320
C337
C338
C341
C383
C384
C404
C410
C413
C413
C414
C416

0CE476SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC

0CK224DF56A

0CE106SF6DC

0CK224DF56A
0CK224DF56A
0CK224DF56A
0CK224DF56A

0CK224DF56A
0CE476SF6DC
0CE476SF6DC

0CE684DK618
0CE476SF6DC

0CE105CK636

0CE106DK618
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE105DK618

0CE107DF618

0CE107DF618

0CE335DK618

0CE474DK618

0CE474DK618

0CE474DK618

0CE474DK618

0CE106DF618

0CE476DF618

0CE106DF618

0CE106DF618
0CE106SF6DC
0CE106SF6DC

0CE107DH618
0CE476SF6DC
0CE476SF6DC

0CE335DK618

0CE225DK618
0CE476SF6DC

47UF MVG 16V M
10UF MVG 16V 20%
100UF MVG 16V M
10UF MVG 16V 20%
100UF MVG 16V M
10UF MVG 16V 20%
220000PF 2012 16V 10%
10UF MVG 16V 20%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
47UF MVG 16V M
47UF MVG 16V M

0.68UF STD 50V 20%
47UF MVG 16V M
1UF SHL,SD 50V M
10UF STD 50V M
47UF MVG 16V M
47UF MVG 16V M
47UF MVG 16V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
1UF STD 50V M
100UF STD 16V M
100UF STD 16V M

3.3UF STD 50V 20%

0.4700UF STD 50V M

0.4700UF STD 50V M

0.4700UF STD 50V M

0.4700UF STD 50V M
10UF STD 16V M
47UF STD 16V M
10UF STD 16V M
10UF STD 16V M
10UF MVG 16V 20%
10UF MVG 16V 20%
100UF STD 25V M
47UF MVG 16V M
47UF MVG 16V M

3.3UF STD 50V 20%

2.2UF STD 50V 20%
47UF MVG 16V M

LOCA. NO PART NO DESCRIPTION

C420
C421
C424
C427
C429
C431
C434
C436
C438
C440
C441
C441
C443
C445
C445
C448
C451
C454
C460
C463
C468
C469
C471
C472
C479
C485
C488
C489
C491
C494
C505
C506
C507
C510
C523
C524
C671
C672
C673
C674
C675
C676
C725
C726
C755
C758
C760
C765
C766
C769
C770

0CN105EJ56A
0CE107DF618
0CE107DF618
0CE107DF618
0CE107DF618
0CE107DF618
0CE227DF618
0CE477DF618
0CE477DF618

0CE106SF6DC

0CN105EJ56A
0CE107DF618
0CE477DF618

0CE106SF6DC

0CE477DF618
0CE107DF618
0CE476DF618
0CE107DF618
0CE106DF618

0CE477DF618
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC

0CK224DF56A
0CE106SF6DC

0CK224DF56A

0CK224DF56A

0CK224DF56A

0CK224DF56A

0CK224DF56A

0CN105EJ56A
0CE106SF6DC

0CE477DK618

0CE477DK618

0CE477DK618

0CE477DK618

181-120K
181-120K

0CE476SF6DC

0CN105EJ56A
0CE107SF6DC
0CE227VF6DC
0CE477VF6DC
0CE477VF6DC
0CE477VF6DC
0CE477VF6DC
0CE227VF6DC

1.0UF 3216 35V 10%
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
100UF STD 16V M
220UF STD 16V M
470UF STD 16V 20%
470UF STD 16V 20%
10UF MVG 16V 20%

1.0UF 3216 35V 10%
100UF STD 16V M
470UF STD 16V 20%
10UF MVG 16V 20%
470UF STD 16V 20%
100UF STD 16V M
47UF STD 16V M
100UF STD 16V M
10UF STD 16V M
470UF STD 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
100UF MVG 16V M
10UF MVG 16V 20%
220000PF 2012 16V 10%
10UF MVG 16V 20%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%
220000PF 2012 16V 10%

1.0UF 3216 35V 10%
10UF MVG 16V 20%
470UF STD 50V 20%
470UF STD 50V 20%
470UF STD 50V 20%
470UF STD 50V 20%
2200PF 4KV M E
2200PF 4KV M E
47UF MVG 16V M

1.0UF 3216 35V 10%
100UF MVG 16V M
220UF MV 16V 20%
470UF MV 16V 20%
470UF MV 16V 20%
470UF MV 16V 20%
470UF MV 16V 20%
220UF MV 16V 20%

REPLACEMENT PARTS LIST

- 26 -

LOCA. NO PART NO DESCRIPTION

C772
C774
C785
C786
C787
C788
C789
C791
C793
C810
C811
C812
C817
C820
C824
C826
C828
C839
C879
C883
C893
C896
C899
C904
C913
C914
C915
C928
C929
C930
C931
C949
C951
C964
C965
C966
C968
C969
C971
C973
C980
C981
C982
C986
C993
C994
C995
C998

JP1

0CE477VF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE227VF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE227VF6DC
0CE477VF6DC
0CE107SF6DC
0CE107SF6DC

0CN105EJ56A
0CE107SF6DC
0CE227VF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477VF6DC
0CE477VF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477VF6DC
0CE477VF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC

6612VLH002A

470UF MV 16V 20%
220UF MV 16V 20%
47UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
47UF MVG 16V M
47UF MVG 16V M
220UF MV 16V 20%
220UF MV 16V 20%
47UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
10UF MVG 16V 20%
220UF MV 16V 20%
470UF MV 16V 20%
100UF MVG 16V M
100UF MVG 16V M

1.0UF 3216 35V 10%
100UF MVG 16V M
220UF MV 16V 20%
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
470UF MV 16V 20%
470UF MV 16V 20%
100UF MVG 16V M
47UF MVG 16V M
100UF MVG 16V M
220UF MV 16V 20%
220UF MV 16V 20%
470UF MV 16V 20%
470UF MV 16V 20%
100UF MVG 16V M
100UF MVG 16V M
47UF MVG 16V M
220UF MV 16V 20%
47UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M
100UF MVG 16V M

JACK,RCA SP026B 4P

LOCA. NO PART NO DESCRIPTION

P001
P002
P003
P004
P101
P102
P102
P103
P103
P104
P105
P106

A692
AR1066
AR1400
AR1401
AR1402
AR1403
AR1460
AR1461
AR1462
AR1463
AR1465
AR1466
AR1467
AR1468
AR1469
AR1470
AR1471
AR1472
AR1473
AR1474
AR1475
AR1476
AR1516
AR1517
AR260
AR261
AR262
AR263
AR264
AR265
AR400
AR401
AR402
AR403
AR460
AR461
AR462

6612J00010B
6612J00010B

380-068D
6612VAH001A
6612JH003CA

6612J00010A

380-068D

380-363K

6612BBBHN6A

6612VMV002A
6612JH003CA

380-068E

0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D

JACK,RCA PPJ128A2 A/V 3P
JACK,RCA PPJ128A2 A/V 3P
JACK,PHONE UEJCV003
JACK,PHONE HEC3900010110
JACK,RCA PPJ137A AUDIO LMONO
JACK,RCA PPJ128A1 A/V 2P MONO
JACK,PHONE UEJCV003
JACK,DIN PJ6046G H=8.0
JACK,DIN 4400621 AMP DVI INTERACED
JACK,DRAWING UCTEX020
JACK,RCA PPJ137A AUDIO LMONO
JACK,PHONE UEJCV018

22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%

REPLACEMENT PARTS LIST

RESISTOR

JACK

- 27 -

LOCA. NO PART NO DESCRIPTION

AR463
AR465
AR466
AR467
AR468
AR469
AR470
AR471
AR472
AR473
AR474
AR475
AR512
AR513
AR514
AR515
AR516
AR517
AR550
AR551
AR552
AR553
AR691
AR693
AR694
AR695
AR696
IC333
IC334
IC337
IC338
IC341
IC342
R020
R021
R030
R032
R589
R590
R655
R656

SW001
SW002
SW003
SW004
SW005
SW006
SW102
SW741

0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001C
0RRZVTA001C
0RRZVTA001C
0RRZVTA001C
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D

0RS2701K607

0RS2701K607
0RS0221H609
0RS0221H609

0RRZVTA001D
0RRZVTA001D

0RD4700H609
0RD4700H609

140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
140-275A
140-313B

22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%

4.7K OHM 1 / 16 W 1608 5%

4.7K OHM 1 / 16 W 1608 5%

4.7K OHM 1 / 16 W 1608 5%

4.7K OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%

2.7K OHM 2 W 5.00%

2.7K OHM 2 W 5.00%

2.2 OHM 1/2 W 5.00%

2.2 OHM 1/2 W 5.00%
22 OHM 1 / 16 W 1608 5%
22 OHM 1 / 16 W 1608 5%
470 OHM 1/2 W 5.00%
470 OHM 1/2 W 5.00%

SWITCH,TACT SKHV17910B 12V
SWITCH,TACT SKHV17910B 12V
SWITCH,TACT SKHV17910B 12V
SWITCH,TACT SKHV17910B 12V
SWITCH,TACT SKHV17910B 12V
SWITCH,TACT SKHV17910B 12V
SWITCH,PUSH JDPB21SA 30V
SWITCH,TACT 2LEAD 160G(TA)

LOCA. NO PART NO DESCRIPTION

SW800

F601
F602
IC411
IC412
IC413
L001
L002
L003
L004
L007
L008
L009
L010
L100
L101
L204
L303
L304
L403
L404
L405
L407
L411
L412
L421
L422
L424
L425
L871
L873
L874
L875
L876
L877
L878
L879
L880
L881
L882
L883
L884
L887
L888
L889
L890
L900
L901
L902

6600VM2006A

6200VJS001A
6200VJS001A

6200C000010
6200C000010

6200C000009
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0005A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0005A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A

SWITCH,PUSH SDDF3PATP011 250V

FILTER,EMC ZJY51R54P
FILTER,EMC ZJY51R54P
FILTER,BAND PASS H354LAIK5202
FILTER,BAND PASS H354LAIK5202
FILTER,BAND PASS H354LAIK5225
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC BK2125 HS 750
FILTER,EMC BK2125 HS 750
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC BK2125 HS 750
FILTER,EMC BK2125 HS 750
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT

REPLACEMENT PARTS LIST

SWITCH

FILTER & CRYSTAL

- 28 -

LOCA. NO PART NO DESCRIPTION

L903
L904
L905
L906
L907
L908
L909
L910
L911
L912
L913
L914
L915
L916
L917
L918
L919
L920
L921
L922
L923
L924
L925
L926
L927
L928
L929
R129
R130
X001
X1470
X1501
X301
X410
X470
X501
X601
X720

L401
L870
L886
P001
P101
P102B
P104
P741
TU201

6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A

6200JB8007L
6200JB8007L

156-A01P

6202VDT002E

6202VDT002J

6202VDT002H

6212AB2015B

6202VDT002E

6202VDT002J

156-A02M

6212AB2015C

6140VR0006A
6140VB0004B
6140VB0004B
6726VV0006E

6630VGA001C

387-B04C
6630VGA001C
6630VGA004B
6700VNF019E

FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC FBMH3216 HM501NT
FILTER,EMC HH2012 1M221JT
FILTER,EMC HH2012 1M221JT
RESONATOR,CRYSTAL HC49U 8.000MHZ
RESONATOR,CRYSTAL SX1SMD 20250000HZ
RESONATOR,CRYSTAL SX1 13.500000MHZ
RESONATOR,CRYSTAL SX1 18.432000MHZ
RESONATOR,CRYSTAL HC49/SM5H 20MHZ
RESONATOR,CRYSTAL SX1SMD 20250000HZ
RESONATOR,CRYSTAL SX1 13.500000MHZ
RESONATOR,CRYSTAL HC49U 18.432MHZ
RESONATOR,CRYSTAL HC49/SM4H 25MHZ

COIL,ENERGY RECOVERY GET 100UH
COIL,CHOKE 26UH
COIL,CHOKE 26UH
REMOTE CONTROLLER RECEIVER,38KHZ
CONNECTOR,DSUB 15PIN 2.29MM
CONNECTOR ASSEMBLY,4P 2.5MM
CONNECTOR,DSUB 15PIN 2.29MM
CONNECTOR,DSUB 9P 2.77MM
TUNER,TAFHH001P LG NTSC FS

LOCA. NO PART NO DESCRIPTION

X830

A1
A2
A3
A4

6204B47985D

3828VA0415G
6710V00100D
6410VUH005A
6612VMV002B

OSCILLATOR,SCO103 12MHZ

MANUAL,OWNERS RU42PZ44/90
REMOTE CONTROLLER
POWER CORD,PS204 125V/13A 2800MM
JACK,DRAWING UCTEX031

REPLACEMENT PARTS LIST

MISCELLANEOUS

ACCESSORIES

PRINTED CIRCUIT BOARD

MAIN(TOP)

PIGGY BACK(TOP) PIGGY BACK(BOTTOM)

MAIN(BOTTOM)

AV(TOP)

AV(BOTTOM)

AV FIX(TOP)

AV FIX(BOTTOM)

POWER SWITCH

CONTROL(TOP)

CONTROL(BOTTOM)

SPEAKER (TOP)

SPEAKER (BOTTOM)