LG RHT298H, RHT299H User Manual

DVB-T HDD/DVD RECORDER

OWNER’S MANUAL

MODEL: RHT297H

RHT298H RHT299H

Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.

RH2T7.2T8-P1L-NA3GLLB-ENG

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION:

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface.This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.

CAUTION:

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED AVOID EXPOSURE TO THE BEAM.

CAUTION:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This product is manufactured to comply with the EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 2006/95/EC.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

About the symbol display . . . . . . . . . . . . . . . . . . . . .4

Symbol Used in this Manual . . . . . . . . . . . . . . . . . . . . .4

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Recordable and Playable Discs . . . . . . . . . . . . . . . . . .5

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Availability of copying or moving feature . . . . . . . . . . . .6

About the internal hard disk drive . . . . . . . . . . . . . . . . .7

Remote Control Operation . . . . . . . . . . . . . . . . . . . . . .7

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Hookup and Settings . . . . . . . . . . . . . . . . . . . . . . . . .10-27

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

General about connection . . . . . . . . . . . . . . . . . . . . . .11

Connecting to the Antenna . . . . . . . . . . . . . . . . . . . . .11

Connections to Your TV . . . . . . . . . . . . . . . . . . . . . . .12

HDMI connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Connecting to an Amplifier . . . . . . . . . . . . . . . . . . . . .14

Accessory Audio/Video (A/V) Connections . . . . . . .15-16

Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . .17

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

General Operation . . . . . . . . . . . . . . . . . . . . . . . .17

General Settings . . . . . . . . . . . . . . . . . . . . . . . . . .18-21

Auto Programming . . . . . . . . . . . . . . . . . . . . . . . .18

Manual Channel Add . . . . . . . . . . . . . . . . . . . . . .18

Program Edit . . . . . . . . . . . . . . . . . . . . . . . . . .19-20

Auto Clock Set / Manual Clock Set . . . . . . . . . . .20

TV Aspect / AV2 Connection . . . . . . . . . . . . . . . . .20

Power Save Mode . . . . . . . . . . . . . . . . . . . . . . . .21

Antenna feed 5V / Initialization . . . . . . . . . . . . . . .21

Language Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Display Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Disc Menu/Audio/Subtitle . . . . . . . . . . . . . . . . . . .21

DTV Audio / DTV Subtitle / DivX Subtitle . . . . . . .21

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Dolby Digital / DTS / MPEG . . . . . . . . . . . . . . . . .22

Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . .22

DRC (Dynamic Range Control) . . . . . . . . . . . . . .22

Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Lock (Parental Control) Settings . . . . . . . . . . . . . .22-23

Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

DVD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

DTV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Set Password . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

DivX Registration Code . . . . . . . . . . . . . . . . . . . .23

Recording Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Record Mode Set / Record Aspect . . . . . . . . . . . .24

DV Recording Audio / TV Recording Audio . . . . . .24

Auto Chapter / AV2 Recording . . . . . . . . . . . . . . .24

Timeshift / MPEG4 . . . . . . . . . . . . . . . . . . . . . . . .24

Video Output Format . . . . . . . . . . . . . . . . . . . . . .24

Disc Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-26

Disc Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Finalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Disc Label / Disc Protect / PBC . . . . . . . . . . . . . .26

Displaying Information . . . . . . . . . . . . . . . . . . . . . . . .27

Displaying Information while TV viewing . . . . . . . .27

Displaying Disc Information on-screen . . . . . . . . .27

TV Viewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28-30

Program Guide (Digital program only) . . . . . . . . . . . . .28

Program Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Program List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Teletext Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-41

General Playback Features . . . . . . . . . . . . . . . . . .31-34

Playing a DivX Movie File . . . . . . . . . . . . . . . . . . . . . .35

Playing an Audio CD or MP3/WMA file . . . . . . . . . . . .36

Program Playback with Audio CD and MP3/WMA file .37

Viewing a JPEG File . . . . . . . . . . . . . . . . . . . . . . .38-39

Editing a MP3/WMA, JPEG, DivX file . . . . . . . . . . .40-41

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-50

About DVD recording . . . . . . . . . . . . . . . . . . . . . . . . .42

About HDD recording . . . . . . . . . . . . . . . . . . . . . . . . .42

Timeshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Basic Recording from a TV . . . . . . . . . . . . . . . . . . . . .44

Instant Timer Recording . . . . . . . . . . . . . . . . . . . . . . .44

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Timer Recording with ShowView®System . . . . . . . . . . . .46

Checking Timer Recording Details . . . . . . . . . . . . . . .47

Recording from an External Input . . . . . . . . . . . . . . . .48

Simultaneous recording and playback . . . . . . . . . . . . .48

Playback another title during recording . . . . . . . . .48

Time Slip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

MPEG4 Recording . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Recording from DV Input . . . . . . . . . . . . . . . . . . . . . .50

Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51-58

Title List and Chapter List Menu Overview . . . . . . . . .51

HDD, VR Mode: Original and Playlist Editing . . . . . . .52

Adding Chapter Markers . . . . . . . . . . . . . . . . . . . . . .52

Changing the Title Thumbnails . . . . . . . . . . . . . . . . . .52

Making a New Playlist . . . . . . . . . . . . . . . . . . . . . . . .53

Adding Additional Title/Chapters to the Playlist . . . . . .53

Deleting an Original or Playlist Title/Chapter . . . . . . . .54

Deleting a Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Naming a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Combining Two Titles Into One . . . . . . . . . . . . . . . . . .56

Combining Two Chapters Into One . . . . . . . . . . . . . . .56

Divide One Titles Into Two . . . . . . . . . . . . . . . . . . . . .57

Moving a Playlist Chapter . . . . . . . . . . . . . . . . . . . . . .57

Hide a Chapter/Title . . . . . . . . . . . . . . . . . . . . . . . . . .58

Protect a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Additional functions for the recordable DVD discs . . . .58

Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-61

Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Dubbing from HDD to DVD . . . . . . . . . . . . . . . . . . . .60

Dubbing from DVD to HDD . . . . . . . . . . . . . . . . . . . . .60

One Touch Copy (HDD to DVD) . . . . . . . . . . . . . . . . .61

One Touch Copy (DVD to HDD) . . . . . . . . . . . . . . . . .61

Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62-67

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . .62

Viewing Title List menu displayed on other

DVD Recorders or Players . . . . . . . . . . . . . . . . .62

Playing Your Recordings on Other DVD

Players (Finalizing a Disc) . . . . . . . . . . . . . . . . . .62

Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Controlling Your TV with the Supplied

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .65-66

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Introduction

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.

This manual provides information on the operation and maintenance of your recorder. Should the unit require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols are applicable only to the disc represented by the symbol.

Titles recorded on the HDD

All DVD discs listed below.

DVD-RAM disc

DVD-RW with VR recording mode

DVD-RW with Video recording mode DVD+RW disc DVD-R disc DVD+R (DL) disc DVD-Video disc

Video CDs Audio CDs DivX files MP3 files WMA files JPEG files

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

JPEG

WMA

MP3

DivX

ACD

VCD

DVD

-R

+RW

-RW

Video

-RW

RAM

DVD ALL

HDD

Moisture Condensation

Never operate this product immediately after moving it from a cold location to a warm location. Leave it for two or three hours without operating it. If you use this product in such a situation, it may damage discs and internal parts.

What is SIMPLINK?

Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection.

• Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

• Refer to the TV owner’s manual for the details of SIMPLINK function.

• LG TV with SIMPLINK function has the logo as shown above.

Recordable and Playable Discs

DVD-RW (Digital Video Disc - ReWritable):

 DVD-RW discs can be formatted for VR mode recording or Video mode recording.  These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again

on the same Disc.

[VR mode]

 Recordings can be extensively edited  Playable only on VR mode compatible players (after finalization)

[Video mode]

 Playable on regular DVD players (after finalization)  Limited editing features

DVD-R (Digital Video Disc - Recordable)



These Discs can be recorded only once. After you finalize a DVD-R, you cannot record on it or edit it.

 DVD-R discs can be only formatted to Video mode.  Playable on regular DVD players (after finalization)  Limited editing features

DVD-RAM (DVD - Random Access Memory)

 DVD-RAM discs can be formatted for VR mode recording.



These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.

 Playable on DVD-RAM compatible players.  Recordings can be extensively edited.  Only DVD-RAM standard Version 2.0, 2.1 and 2.2 discs can be used in this unit.  You cannot use the cartridge-type DVD-RAM disc in this unit.

DVD+RW (Digital Video Disc + ReWritable)

 These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again

on the same Disc.

 Playable on DVD+RW compatible players (automatically finalization)  The edited contents are playable on DVD+RW compatible players only after finalization  Recordings can be edited the title/chapter

DVD+R (Digital Video Disc + Recordable)

 These Discs can be recorded only once. After you finalize a DVD+R, you cannot record on it or edit

it any more.

 Playable on DVD+R compatible players (after finalization)  Any edited contents are not be compatible on DVD+R compatible players. (Hide, chapter combine,

added chapter mark, etc.)

 Limited title/chapter editing features.

DVD+R DL (Digital Video Disc + Recordable; Double Layer)

 These Discs can be recorded only once. After you finalize a DVD+R DL, you cannot record on it or

edit it any more.

 Storage space is nearly doubled with double layer DVD+R media, allowing consumers to record up

to 8.5GB of video on a single DVD+R disc.

 Playable on DVD+R DL compatible players (after finalization)  Any edited contents are not be compatible on DVD+R DL compatible players. (Hide, chapter

combine, added chapter mark, etc.)

 Limited title/chapter editing features.

Recommended recordable DVD discs

DVD-R DVD+R DVD-RW DVD+RW DVD+R(DL) DVD-RAM

Mitsubishi (8x, 16x) Mitsubishi (8x, 16x) Mitsubishi (4x) Mitsubishi (4x) Mitsubishi (2.4x) Fujifilm (2x)

That’s (8x, 16x) Ricoh (8x, 16x) Verbatim (4x) SONY (2.4x) Maxell (2.4x) Mitsubishi (3x)

SONY (16x) SONY (16x) JVC (4x) Verbatim (2.4x) - -

- - Victor (4x) Ricoh (2.4x, 4x) - -

- - Maxell (4x) - - -

Note: If a DVD-RW/DVD+RW discs is recorded using a personal computer or other DVD recorder, you cannot format the disc using this recorder. So if you want to use the disc on this recorder, you must format the disc using the original recorder.

Introduction

Playable Discs

DVD (8 cm / 12 cm disc)

Discs such as movies that can be purchased or rented

Video CD (VCD) (8 cm / 12 cm disc)

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD/Super VIDEO CD format

Audio CD (8 cm / 12 cm disc)

Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased

CD-R/CD-RW (8 cm / 12 cm disc)

CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or JPEG files.

Notes:

 Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some

CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

 Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.  Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.  Depending on the recording software & the finalization, some recorded discs (CD-R/RW or DVD±R/RW) may

not be playable.

 DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder

may not play if the disc is damaged or dirty, or if there is dirt or condensation on the Recorder’s lens.

 If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases

in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

 This recorder requires discs and recordings to meet certain technical standards in order to achieve optimal

playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain preexisting conditions (see above) to ensure compatible playback.

 Customers should note that permission is required in order to download MP3 / WMA files and music from the

Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

Regional Code

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”.

Notes on Regional Codes



Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play.



If you try to play a DVD with a different regional code from the unit, the message “Incorrect region code. Can’t play back” appears on the TV screen.

Availability of copying or moving feature

From To MP3/WMA JPEG DivX Audio CD Video CD Title*

HDD DISC No No No No No Yes

DISC HDD Yes Yes Yes No No Yes

*1 The title is recorded from this unit.

About the internal hard disk drive

The internal hard disk drive (HDD) is a fragile piece of equipment. Please use the recorder following the guidelines below to protect against possible HDD failure. We recommend that you back up your important recordings onto DVD discs in order to protect against accidental loss.

 Do not move the recorder while it is on.

 Install and use the recorder on a stable, level

surface.

 Do not block the rear vent/cooling fan.

 Do not use the recorder in excessively hot or humid

places, or in places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the recorder. This can be a cause of HDD failure.

 While the recorder is switched on, do not unplug

from the wall socket or switch the electricity off from the breaker switch.

 Do not move the recorder immediately after

switching it off. If you need to move the recorder, please follow the steps below:

1. After the message POWER OFF is shown in the display, wait at least two minutes.

2. Unplug from the wall socket.

3. Move the recorder.

 If there’s a power failure while the recorder is on

there is a chance that some data on the HDD will be lost.

 The HDD is very delicate. If used improperly or in

an unsuitable environment, it is possible that the HDD will fail after a few years of use. Signs of problems include playback unexpectedly freezing and noticeable block noise (mosaic) in the picture. However, sometimes there will be no warning signs of HDD failure.

If the HDD fails, no playback of recorded material will be possible. In this case it will be necessary to replace the HDD unit.

Remote Control Operation

Point the Remote Control at the remote sensor and press the buttons.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Remote Control Battery Installation

Remove the battery cover on the rear of the Remote Control, and insert two R03 (size AAA) batteries with and matched correctly.

Introduction

/ I (POWER button)

Switches the recorder ON or OFF.

b Disc Tray

Insert a disc here.

c Display window

Shows the current status of the recorder.

T/S: Indicates the timeshifting mode.

REC: The recorder is recording.

HDD: The recorder is HDD mode.

DVD: The recorder is DVD mode. HDD bBDVD: The recorder is dubbing.

TV: Indicates when the recorder is in TV tuner

mode.

: Indicates when the recorder is in timer

recording or a timer recording is programmed.

: Indicates clock, total playing time, elapsed time, title number, chapter/track number, channel, etc.

d Remote Sensor

Point the recorder remote control here.

e Z (OPEN/CLOSE)

Opens or closes the disc tray.

f HDD/DVD

Set the recorder’s mode to HDD or DVD.

g RESOLUTION

Sets the output resolution for HDMI and COMPONENT OUTPUT jacks.

- HDMI: 576i, 576p, 720p, 1080i

- COMPONENT: 576i, 576p

h N / X (PLAY / PAUSE)

Starts playback. Pause playback or recording temporarily, press again to exit pause mode.

i x (STOP)

Stops playback or recording.

j z (REC)

Starts recording. Press repeatedly to set the recording time.

k PROG. (V/v)

Scans up or down through memorized channels.

l DV IN

Connect the DV output of a digital camcorder.

m AV IN 3 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.).

Front Panel

ab cdefghijk

     a    

POWER: Switches the recorder ON or OFF.

OPEN/CLOSE (Z): Opens and closes the disc tray.

DVD: Selects the unit’s function mode to DVD.

HDD: Selects the unit’s function mode to HDD.

AV: Changes the input to use for recording (Tuner, AV1-3, or DV IN).

0-9 numerical buttons: Selects numbered options in a menu.

TV/DVD: To view channels selected by the recorder tuner or by the TV tuner.

TV Control Buttons: See page

64.

     b    

DISPLAY: Accesses On-Screen Display.

REC (z): Starts recording. ZOOM: Enlarges video image. REPEAT: Repeat chapter, track,

title, all. TV/RADIO: Switches between TV

and Radio modes.

Teletext Buttons

- (INDEX): Moves to Index screen. If Index page is not present, moves to page 100.

- (TEXT): Switches between teletext mode and normal TV viewing.

- (FREEZE): Holds the teletext display and stops the automatic page change in the teletext mode.

- (MIX): Selects the background for teletext screen (Opaque, User Transparency, Transparency).

     c    

SCAN (m / M): Search backward or forward.

SKIP (. / >): Go to next or previous chapter or track.

PAUSE/STEP (X) : Pause playback or recording temporarily.

PLAY (N): Starts playback. STOP (x): Stops playback or

recording.

     d    

HOME: Accesses or removes the HOME menu.

MENU/LIST: Accesses menu on a DVD disc. Switches between Title List-Original and Title List-Playlist menu.

b / B / v / V (left/right/up/down):

Selects an option in the menu. ENTER ( ): Acknowledges menu

selection. PR (+/-): Scans up or down

through memorized channels.

GUIDE: Displays the Program Guide.

RETURN (O): Removes the menu.

     e    

FAV: Changes to the favorite program.

AUDIO: Selects an audio language or audio channel.

SUBTITLE: Selects a subtitle language.

TIMESHIFT: Activates pause live TV/playback (timeshift) for a live TV program.

MARKER: Marks any point during playback.

SEARCH: Displays Marker Search menu.

DUBBING: Copies DVD to HDD (or HDD to DVD).

CLEAR: Removes a track number on the Program List or a mark on the Marker Search menu.

TITLE: Displays the disc’s Title menu, if available.

THUMBNAIL: Selects a thumbnail picture.

RANDOM: Plays tracks in random order.

CHP. ADD: Inserts a chapter marker when playing.

PIP: Selects PIP function on or off. S

HOWVIEW: To display the program

menu for S

HOWVIEW System

programming.

Remote Control

Introduction

a ANTENNA IN

Connect the antenna to this terminal.

b COMPONENT OUTPUT (Y P

B PR)

Connect to a TV with Y P

B PR inputs.

c AV 2 (DECODER)

Connect the audio/video output of an external source (Pay-TV decoder, Set Top Box, VCR, etc.).

d Cooling fan

e AC IN ~

Plug into the power source.

f ANTENNA OUT

Passes the signal from the ANTENNA IN to your TV/monitor

g OPTICAL (Digital audio out jack)

Connect to digital (optical) audio equipment.

h COAXIAL (Digital audio out jack)

Connect to digital (coaxial) audio equipment.

i S-VIDEO OUTPUT

Connect to a S-Video Input on TV.

j AUDIO OUTPUT (Left/Right)

Connect to a TV with audio inputs.

k AV 1

Connect to a TV with SCART jack.

l HDMI Connector (Type A)

HDMI output providing a high quality interface for digital audio and video.

abc d e

fghij k l

Rear Panel

Hookup and Settings

General about connection

Picture and sound

Digital TV is a transmission technology that replaces the traditional analogue technique.

This means that several TV channels, radio channels and other digital services can be transmitted on the same space as just one channel took up before. As a consumer you get access to many more channels and services than before at the same time as they are received with perfect picture and audio quality.

The recorder converts the digital signal into a format that is suitable for your TV and sound system.

Connecting your recorder is just as simple as connecting for example a video recorder. You get the best picture quality by using a HDMI cable for connection to your TV-set. The best audio experience is obtained by connecting an optical cable to your sound system.

Coverage

Before buying this product it is anticipated that you have made sure that there are digital transmissions covering your region.

Antenna / Signal source

Depending on the reception your recorder may be connected to a simple indoor antenna or to an existing outdoor antenna system. If you live in a flat you should make sure that the digital terrestrial signals are distributed to your wall antenna outlet. If you have your own antenna system you must make sure that it is equipped with antennas, filter and/or amplifier that can handle those frequencies that the digital channels are transmitted on.

Cable-TV

Please observe that this recorder is not designed for the reception of regular digital cable-TV signals (QAMsignal). Despite this, operators of smaller cable networks may have chosen to distribute the digital terrestrial signals (COFDM-signal) in the network. In this case this recorder may well be used.

Check with your landlord if you are insecure about what type of TV-signal that is provided in the wall antenna outlet.

Connecting to the antenna

Remove the antenna cable plug from your TV set and insert it into the antenna socket at the back of the recorder. Plug one end of the antenna cable into the TV socket on the recorder and the other end into the antenna input socket on your TV set.

Caution

The ANTENNA IN jack supply the antenna feed (DC 5V/100mA) and the antenna feed is switchable via setup menu. If your digital antenna is not an active antenna, you must set the [Antenna feed 5V] option to [OFF].

RF coaxial connection

Connect the ANTENNA OUT jack on the recorder to the antenna input jack on the TV using the 75-ohm Coaxial Cable supplied (R). The ANTENNA OUT jack passes the signal through from the ANTENNA IN jack.

Hookup and

Settings

and/or

Antenna (Analog)

ANTENNA

INPUT

Rear of TV

AUDIO INPUT

VIDEO INPUT

Antenna

(Digital)

Rear of the recorder

Connections to Your TV



Make one of the following connections, depending on the capabilities of your existing equipment.



When using the COMPONENT OUTPUT jacks, set the Video Output Format option in the setup menu to YP

BPR. When using the SCART jack, set the

Video Output Format option in the setup menu to RGB.

Tips



Depending on your TV and other equipment you wish to connect, there are various ways you could connect the recorder. Use only one of the connections described below.



Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

Caution

– Make sure the recorder is connected directly to the

TV. Tune the TV to the correct video input channel.

– Do not connect the recorder’s AUDIO OUTPUT jack

to the phono in jack (record deck) of your audio system.

– Do not connect your recorder via your VCR. The

DVD image could be distorted by the copy protection system.

SCART connection

Connect the AV1 scart jack on the recorder to the corresponding in jacks on the TV using the scart cable

(T).

S-Video connection

Connect the S-VIDEO OUTPUT jack on the recorder to the S-Video in jack on the TV using the S-Video cable (S).

Audio (Left/Right) Connection

Connect the left and right AUDIO OUTPUT jacks of the recorder to the audio left and right IN jacks on the TV using the audio cables (A). Do not connect the recorder’s AUDIO OUTPUT jack to the phono in jack (record deck) of your audio system.

Component Video connection

Connect the COMPONENT OUTPUT jacks on the recorder to the corresponding input jacks on the TV using an Y P

B PR cable (C).

If your television is a high-definition or “digital ready” television, you may take advantage of the recorder’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the recorder.



Set the resolution to 576p for progressive signal using RES. button on the front panel.

Note:

Progressive scan does not work with the analog video connections (S-VIDEO OUTPUT jack).

Caution:

If the resolution is set to 720p or 1080i, the S-VIDEO OUTPUT, SCART and COMPONENT OUTPUT connections are not available.

Rear of TV

AUDIO INPUT

S-VIDEO

INPUT

COMPONENT VIDEO INPUT

SCART INPUT

Rear of the recorder

HDMI connection

If you have an HDMI TV or monitor, you can connect it to this recorder using an HDMI cable.

1. Connect the HDMI OUTPUT jack on the recorder to the HDMI INPUT jack on a HDMI compatible TV or monitor (H).

2. Set the TV’s source to HDMI (refer to TV’s Owner’s manual).

Notes:

 If your TV is NOT capable of handling 96 kHz

sampling frequency, set the [Sampling Freq.] option to [48 kHz] on the setup menu (See page 22). When this choice is made, this unit will automatically convert any 96 kHz signals to 48 kHz so your system can decode them.

 If your TV is not equipped with Dolby Digital and

MPEG decoder, set the [Dolby Digital] and [MPEG] options to [PCM] on the setup menu (See page 22).

 If your TV is not equipped with DTS decoder, set

the [DTS] options to [OFF] on the setup menu (See page 22). To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs.

 The arrow on the cable connector body should face

up for correct alignment with the connector on the recorder.

 If there is noise or lines on the screen, please check

the HDMI cable.

Tip :

When you use the HDMI connection, you can change the resolution (576i, 576p, 720p, or 1080i) for the HDMI output using RES. button on the front panel.

Caution:

Changing the resolution when the recorder is connected with HDMI connector may result in malfunctions. To solve the problem, turn off the recorder and then turn it on again.

About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD Players, Set-Top Boxes, and other AV devices. HDMI was developed to provide the technologies of HDCP (High Definition Contents Protection). HDCP is used to protect digital content transmitted and received.

HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

Additional Information for HDMI

 When you connect an HDMI or DVI compatible

device make sure of the followings:

- Try switching off the HDMI/DVI device and this recorder. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this recorder.

- The connected device’s video input is set correctly for this unit.

- The connected device is compatible with 720(1440)x576i, 720x576p, 1280x720p, or 1920x1080i video input.

 Not all HDCP-compatible DVI devices will work with

this recorder.

- The picture will not be displayed properly with non-HDCP device.

HDMI

HDMI compatible TV

Rear of the recorder

(Type A)

Hookup and

Settings

Connecting to an Amplifier

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic

Connect the Left and Right AUDIO OUTPUT jacks on the recorder to the audio left and right in jacks on your amplifier, receiver, or stereo system, using the audio cables (A).

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

1. Connect one of the recorder’s DIGITAL AUDIO OUTPUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.

2. You will need to activate the recorder’s digital output. (See “Audio Settings” on page 22).

Digital Multi-channel sound

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your recorder (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

Notes:

– If the audio format of the digital output does not

match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

– Six Channel Digital Surround Sound via digital

connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder.

– To see the audio format of the current DVD in the

on-screen display, press AUDIO.

– This recorder does not perform internal (2 channel)

decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the doubleD symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Rear of the recorder

AXO

OPTICAL

DIGITAL INPUT

COAXIAL

AUDIO INPUTDIGITAL INPUT

Amplifier (Receiver)

Accessory Audio/Video (A/V) Connections

Connecting a PAY-TV/Canal Plus Decoder

You can watch or record PAY-TV/Canal Plus programs if you connect a decoder (not supplied) to the recorder. Disconnect the recorder’s mains lead from the mains when connecting the decoder.

To watch or record PAY-TV/Canal Plus programs, set [AV2 Connection] option to [Decoder] (see page 20) and set the program’s [CANAL] option to [On] on the Setup menu (page 20).

Tip:

You do not need to turn on the recorder to view the signals from the connected tuner on your TV.

Note:

If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected decoder.

Connecting to the AV 2 (DECODER) jack

Connect a VCR or similar recording device to the AV 2 (DECODER) jack of this recorder.

To watch or record the source from AV 2 (DECODER) jack, set [AV2 Connection] option to [Others] (see page 20) and set [AV2 Recording] option to [Auto], [CVBS] or [RGB] as required (see page 24).

Tip:

You do not need to turn on the recorder to view the signals from the connected tuner on your TV.

Notes:

 Pictures containing copy protection signals that

prohibit any copying cannot be recorded.

 If you pass the recorder signals via the VCR, you

may not receive a clear image on your TV screen. Be sure to connect your VCR to the recorder and your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV.

 When you record to a VCR from this recorder, do

not switch the input source to TV by pressing the TV/DVD button on the remote.

 If you are using a B Sky B tuner, be sure to connect

the tuner’s VCR SCART jack to the AV 2 (DECODER) jack.

 If you disconnect the recorder’s mains lead, you will

not be able to view the signals from the connected VCR or tuner.

VCR RECORDER

Line input 1

Line input 2

Hookup and

Settings

PAY-TV/Canal Plus Decorder

SCART AV

VCR, Cable Box, or

Satellite Tuner, etc.

Rear of the recorder

Connecting to the AV IN 3 Jacks

Connect the input jacks (AV IN 3) on the recorder to the audio/video out jacks on your accessory component, using audio/video cables.

Connecting a Digital Camcorder

Using the front panel DV IN jack, it is possible to connect a DV digital camcorder and digitally transfer DV tapes to DVD.

Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder to the front panel DV IN jack of this recorder.

Notes:

 This jack is for connection to DV digital camcorder

only. It is not compatible with digital satellite tuners or D-VHS video decks.

 Disconnecting the DV cable while recording a

contents of the connected digital camcorder may result in malfunction.

Auto Setup

After the POWER is pressed for the first time to turn on the unit or resetting the unit, the Initial Setup Wizard function sets the language, clock and tuner channels automatically.

1. Select a language for the Setup menu and on-

screen display. Use v / V to select a language then press ENTER.

2. Please check your antenna connections. Press ENTER to move next step.

3. Use v / V to select the Clock Set option then press ENTER.



[

Auto]: When Channel auto search is completed the actual Time and Date are also set automatically. (See “Auto Clock Set” on page 20.)



[

Manual]:

Enter the necessary information for

date and time. b / B (left/right): Moves the cursor to the

previous or next column. v / V (up/down): Changes the setting at the

current cursor position. Press ENTER to confirm your setting.

4. Use v / V to select a country and press B button

then press ENTER while [Start] option is selected. The tuner will automatically cycle through all available channels in the area and place them in the tuner’s memory. You can skip the analog channel scanning by pressing B.

5. Press ENTER to finish the setup.

Jack panel of Accessory Component

(VCR, Camcorder, etc.)

AUDIO

OUTPUT

VIDEO

OUTPUT

Front of the recorder

DV Digital Camcorder

IN/OUT

Front of the recorder

Using the Home Menu

From the Home Menu screen you can access all the Media for playback and recording of the recorder.

1. Press HOME to display the Home Menu screen.

2. Use the b / B buttons to select a main option you

want. Sub options appears.

3. Use the v / V and ENTER buttons to select the

sub option you want.

4. To exit the HOME menu, press HOME or

RETURN (O).



TV: Returns to live TV viewing.



Timer Record: Displays [Timer Record List] menu. (See page 45)



ShowView: To display the program menu for S

HOW

VIEW System programming.

(See page 46)

MOVIE



HDD: Displays the Title List menu for HDD. (

page

51)



HDD DivX: Displays the [Movie List] menu for HDD. (page 35)



DISC:

- Displays Title List menu for recordable disc

(page 51)

- Displays [Movie List] menu for DivX disc. (page 35)

- Plays Video CD or DVD-Video disc (page 31-34).

PHOTO (See page 38)



HDD: Displays [Photo List] menu for HDD.



DISC: Displays [Photo List] menu for disc.

MUSIC (See page 36)



HDD: Displays [Music List] menu for HDD.



DISC: Displays [Music List] (or Audio CD) menu for disc.

SPECIAL



Rec Mode: Displays the menu to select the record mode. (See page 24)

SETUP (See page 17)



Start: Displays Setup menu.

Initial Settings

In this menu system, there are several ways to customize the settings provided. Most menus consist of three levels to set up the options, but some require greater depth for the variety of settings.

General Operation

1. Press HOME and select [Setup] option.

2. Select [Start] option then press ENTER. The Setup menu appears.

3. Use v / V to select the desired option.

4. While the desired item is selected, press B to move to the second level.

5. Use v / V to select the second desired option.

6. Press B to move to the third level.

7. Use v / V to select the desired setting then press ENTER to confirm your selection. Some items require additional steps.

8. Press RETURN (O) repeatedly to exit the Setup menu.

Note:

Press b to go back to the previous level.

Hookup and

Settings

General Settings

Auto Programming

This recorder is equipped with a frequency synthesized tuner capable of receiving up to 88 analog channels and 500 digital channels.

Preparation:

Connect the recorder to the desired type of antenna, as shown in Connecting to the Antenna on page 11.

Note:

Password is needed to access the [Auto Programming] option if [Lock System] option is set to [On].

1. Select the [Auto Programming] option.

2. Press B to move to the third level.

[Country] option is highlighted.

3. Use v / V to select a country then press B.

[Start] icon is highlighted. If your country is not listed, select [Others]

4. Press ENTER to begin the channel search. The tuner will automatically cycle through all available channels in the area and place them in the tuner’s memory. You can skip the analog channel scanning by pressing B.

Note:

If you skip the Auto Setup menu and access the Setup menu for the first time, you can only set the [Auto Programming] option. You can set the other options after finishing [Auto Programming].

Manual Channel Add

This feature manually adds channels.

Note:

Password is needed to access the [Add Channel] option if [Lock System] option is set to [On].

1. Select the [Program Edit] option then press B .

2. Use v / V to select the [Add Channel] option then

press ENTER.

3. Use v / V to select [Analog] for analog channel or [Digital] for digital channel then press B.

4. Use v / V to select a channel number. Searches for a channel automatically. Searching stops when the recorder tunes in a channel.

5. Press ENTER to add the channel.

Program Edit

You can edit a channel manually (name, move, etc.).

Note:

Password is needed to access the [Program Edit] option if [Lock System] option is set to [On].

1. Select the [Program Edit] option then press B .

2. Use v / V to select the [Edit] option then press

ENTER. The Program List menu appears.

3. Use v / V to select a PR number then press

ENTER.

4. Use v / V to select the program option then press

ENTER.

 [Favorite] Set the program to favorite channel.

 [Delete] Disables a program position you do not

need.

 [Move] (Analog channel only) Sorts the program

positions on the Program List.

 [Block] Blocks the program.

 [Station Rename] Changes the station name.

The display for entering characters appears. To enter characters, see page 55.

 [Program Edit] (Analog channel only) Sets the

analog channel manually.

5. Press RETURN (O) repeatedly to exit Program

List menu.

Switching the program list to DIGITAL TV, ANALOG TV, or RADIO

1. Press v to move the highlight position to top of the

program list.

2. Press b / B to select a [DIGITAL TV],

[ANALOG TV], or [RADIO] then press ENTER. Selected program list appears.

Setting a favorite program

You can set a program to favorite channel with genre.

1. Press v / V to select a program then press

ENTER.

2. Press v / V to select [Favorite] option then press

ENTER. The genre choice menu will appear.

3. Select a genre then press ENTER. The program is set to the favorite program with genre.

Tip:

You can modify User 1 and User 2 genre. Select User 1 or User 2 then press red color button. The display for entering characters appears.

To enter characters, see page 55.

AV1 Decoder

Sets the AV1 scart jack for inputting encoded video signals.

1. Press AV while the Program List menu appears.

2. Press ENTER so [Canal+] appears on the display.

Press ENTER again to turn off the setting.

 Off: Inputs the signals from the AV1 scart jack.

Normally select this.

 On: The encoded video signal input from the

AV1 scart jack is output to the AV 2 (DECODER) jack for decoding. The decoded signal is then input back through the AV 2 (DECODER) jack so you can record or view PAY-TV/Canal Plus programs.

Hookup and

Settings

Program Edit (Continued)

Program Edit

You can perform a search to select and store TV channels manually. When you select [Program Edit] in step 4 on the previous page, the display for setting channels appears.

1. Use b / B to select the item and press v / V to

change the setting.

 [PR] indicates the selected program position.

 [Seek] Searches for a channel automatically.

Searching stops when the recorder tunes in a channel.

 [Ch.] Changes the channel number.

 [MFT] Fine tunes the channel to obtain a clearer

picture.

 [CANAL] Sets the channels for the decoder. You

need this setting to watch or record PAY-TV/ Canal Plus programs.

 [NICAM] Sets the channels for the NICAM

broadcast. Normally, [NICAM] is set to [ON]. If the sound from NICAM broadcast is not clear, set to [OFF].

2. Choose OK then press ENTER to confirm the setting and returns to the Program List menu.

Auto Clock Set

When Channel auto search is completed the actual Time and Date are also set automatically. If the time in the recorder display is not correct, the clock must be set manually.

1. Select [Clock set] option then press B.

2. Use v / V to select [Auto] option then press

ENTER.

3. If the clock that has automatically set is different

with your local clock, you can add more time using [Time Offset] option. (For example, when summer time is started in local area.) Press B to select [Time Offset] option.

4. Press v / V to select a value then press ENTER

(0, 30, 60, 90, 120). Select “0” if the clock that has automatically set is identified with your local clock.

Note:

There are cases where the TV station does not send, or sends wrong date and/or time information and the recorder sets the incorrect time. If this happens, we recommend that you set the clock manually.

Manual Clock Set

1. Select [Clock set] option then press B.

2. Use v / V to select [Manual] option then press

ENTER.

3. Enter the necessary information for date and time.

b / B (left/right): Moves the cursor to the previous or next column.

v / V (up/down): Changes the setting at the current cursor position.

4. Press ENTER to confirm your setting.

TV Aspect

Selects the aspect ratio of the connected TV (4:3 standard or wide).

 [Letter Box] Select this when connecting to a 4:3

screen TV. Displays a wide picture with bands on the upper and lower portions of the screen.

 [Pan Scan] Select this when connecting to a 4:3

screen TV. Automatically displays a wide picture on the entire screen and cuts off the portions that do not fit.

 [16:9] Select this when connecting to a wide-screen

TV or TV with a wide mode function.

Note:

If the resolution is set to 720p or 1080i, [TV Aspect] will be disable in the setup menu.

AV2 Connection

You can connect a decoder or other device to the AV 2 (DECODER) socket on the back.

 [Decoder] Select [Decoder] if you connect the

recorder’s AV 2 (DECODER) jack to a PAY-TV or Canal Plus decoder.

 [Others] Select [Others] if you connect the

recorder’s AV 2 (DECODER) jack to a VCR or similar recording device.

General Settings (Continued)

Power Save Mode

You can set up the unit into an economic power save mode. Nothing is displayed in the display window when the unit is turned off.

 [OFF] Power Save Mode is not active.

 [ON] Power Save Mode is active.

Notes:

 The encoded television signals (CANAL+ or

PREMIERE) are not decoded in the Power Save Mode.

 The Power Save Mode is not available in the

standby mode for the timer recording and when power off of the unit after receiving the encoded television signals (CANAL+ or PREMIERE).

Antenna feed 5V

If you are using an active antenna, you will have to switch on the antenna feed (DC 5V/100mA). The antenna will be supplied via the ANTENNA IN input. In case of overload, or if there is a short circuit in the antenna feed, this will be switched off automatically. If this occurs, please repair the fault, then switch on the antenna feed again.

Initialization

You can reset the recorder to its original factory settings and initialize the HDD.

 [Factory Set] If you need to, you can reset the

recorder to all its factory settings. Some options cannot be reset. (DVD Rating, Password, and Area Code) Select [Factory Set] icon then press ENTER and auto setup menu will appear, see page 16.

 [HDD format] Initializes the HDD (Hard Disk Drive):

everything recorded on the HDD will be erased.

1. Select [Initialize] option then press B.

2. Press v / V to select the desired option then press

ENTER. The confirm message will appear.

3. Use b / B to select [Yes] or [No] then press

ENTER.

Language Settings

Display Menu

Select a language for the Setup menu and on-screen display.

Disc Menu/Audio/Subtitle

 [Original] Refers to the original language in which

the disc was recorded.

 [Other] To select another language, press ENTER.

Press number buttons then ENTER to enter the corresponding 4-digit number according to the language code list in the reference chapter (see page 63). If you enter the wrong language code, press CLEAR.

 [Off](for Disc Subtitle) : Turn off Subtitle.

DTV Audio

Digital channels sometimes provide multiple audio tracks, often in a different language. You can set a default audio language with this setting.

Tips:

If provided by the broadcaster, you can also select a different audio language while viewing TV by pressing AUDIO repeatedly.

DTV Subtitle

Digital channels sometimes provide subtitle, often in a different language. You can set a default subtitle language with this setting.

Note:

DTV Subtitle will appear only if provided by the broadcaster.

Tips:

 If available, you can also select a subtitle language

while viewing digital TV viewing, press SUBTITLE repeatedly.

 If subtitles are available, the DTV subtitle icon ( )

appears on the program information display to indicate that you can select one of those subtitle options with the SUBTITLE button.

DivX Subtitle

You can select a language code for DivX subtitle.

Hookup and

Settings

+ 46 hidden pages