Page 1
WLAN UNIT & Accessories
LGE Internal Use Only
WLAN UNIT
WLAN UNIT Holder
1 / 8
Screw(2ea)
Page 2
WLAN UNIT setting(Connection)
ppq
LGE Internal Use Only
※ To ensure compliance with FCC RF exposure requirements, this
device must be installed in a location where the antenna of the device
will have a minimum distance of at least 10 cm
Smart Washing Machine
WLAN UNIT connected to
Washing Machine
2 / 8
Page 3
LGE Internal Use Only
h
d
d
bel
2
shows Wi
Fi Setting mode with Ting
sound.
y
확인할
수
있습니다
.
ith
제품
표시부를
Check the product
WLAN UNIT setting(Smart Phone )
1. Access LG Smart Server Homepage with computer
(http://www.smartthinQ.com) and register ID and
password.
2. Apply purchased WLAN UNIT to Smart Washing
Machine, push the reservation button for more than
3 sec. after turning on the washing machine.
‘
-
Wi-Fi Setting Mode
제품이 등록되지 않았습니다.
제품 등록 방법은
Access Wi-Fi Modem setting mode
제품 등록하는 방법 버튼을 눌러
with Smart Phone or Laptop.
IP : 192.168.120.254
SSID : LG_Smart_Laundry
3. Touch the ‘Wi-Fi set’ button below and choose
‘LG_Smart_Laundry’ among Wi-Fi Network. When state
shows “Connected”, come back to current image w
using back button of smart phone.
“
”
or
4. Set the requirement of Wi-Fi Modem which is on the product
with pushing t
1
3
4
① Check the product is ‘Washing Machine’
② Choose Wireless router(AP) that is currently being used for
User AP
(Input the password and connect if Wireless router(AP) has
security application.)
③ ID/PW : mandatory information
(ID/PW of LG Smart Server registration)
* Name : In case of using several product, Give name to
distinguish easily(Optional)
④ Check the registered information and click the Register
Button to complete the registration. Smart phone and
Product show the completion message as below.
e”Pro
uct Setting Mo
Wi-Fi Setting Mode
Wi-Fi Setting has
completed.
e”
ow.
Product registering
Network will be
네트워크는 차단되니
disconnected,
제품 등록 완료는
showing part for register
확인하시기 바랍니다.
completion.
Wi-Fi Set
or
Product Setting Mode
<Product showing part> <Smart Phone image>
3 / 8
Page 4
WLAN UNIT Setting (Product)
g( )
<WLAN UNIT Setting and Reception check>
L1,L2,L3(connection intensity) displayed on 18:88)
WLAN UNIT is not installed, nothing is on the 18:88 while the operation
Wi-Fi Setting Mode
Wi-Fi Setting Mode
Wi-Fi Setting Mode
<Wi-Fi Setting for Product (Refer the bottom)>
18:88 shows Error type when it is failed, or Set mode entering has canceled without any setting (Cancel in Web or App)
• User contacts the Setup mode and save the SSID/Password and user’s information for product registration.
• Enter Wi-Fi Setting Mode after pushing Time Delay or Delay Wash (W) / Time Dry for 3 sec.
• Pushing Long Key(product button is not operating at this condition) shows Wi-Fi condition(L0(Unconnected),
. If
.
Set on 18:88
3 sec. later
-Using mode is changed when Setting is completed.
Same as power on condition.
Connection with smart phone or lab top
From exterior
Wi-Fi 설정 중..
Set on 18:88
Entering User’s information
4 / 8
:SSID/Password
Entering failure
LED shows End on 18:88
Changed to stand by mode automatically.
LED shows ntE (network Error, Fail) mode on
18:88. changed to stand by mode automatically.l
Victor Panel
Page 5
Smart Grid Function Application
Follow AHAM standard
time >10 : DL else SR), with this signal product is operating
p
pg
<Function Definition>
- electric product is operating with DR Signal from electric
Power company(Hyb, Cloud included).
-
- DR Signal Acceptable with Smart On button activated and
Modem is in.
- When DR signal is in, receive DL/SR separately(Duration
Delay Start and Energy Save motion by itself. But for this
product, do not guide to customers
.
Smart on
Smart on
1. Place Smart on(provisional)button (Long Key(more than 3 sec.) of Signal button) and Smart on
LED on the product Panel.
2. Check Modem is in, push the smart button, then Smart On LED turns on
On LED never turns on when
ushing Smart On Button.
. If Modem is not in, Smart
3. Inner Algorithm(Smart Grid related signal processing, AHAM based) is same as Rocky2 TFT LCD
standard.
4. Modem Reset function is needed and can be defined as below.
With Power On,
rSt(reset) on 18:88 and blink, show End when completed.
Operate with Wi-Fi Setting Key + pushing signal for more than 6 sec.
If rSt and End is within 1~2 sec., rSt blinks when Reset has done normally.
After completion, it doesn’t go off before customer sets “power off”. When this status continues for
4 min., it goes off automatically like product’s basic operation.
If Wi-Fi Modem is not in, it may not enter to Modem Reset Mode.
Victor Panel
5 / 8
Page 6
Smart Diagnosis
Final saved Diagnosis factor sends to server when pushing the Smart Diagnosis button(Washing
Wi-Fi also send the final saved diagnosis factor to server
Wi-Fi also can check
machine: water temp. dryer: temp.)
In case of Audible, information of 1 cycle only will be sent because of time restraint(sending takes
about 15 sec.)
.
Function Definition by detailed using Scene will be identified after additional consulting.
Application will be also identified after additional consulting.
.
6 / 8
Page 7
Smart Access
<Function Definition>
1-1-1
Power
On : Power can not be On under any circumstance from exterior
After starting cycles, notice the progress of washing cycle through Push message
can be checked from exterior
: Access and Adapt is available after WLAN UNIT Setting completion.
In case of going out or getting to work after operating Washing Machine,
Smart Phone can power off or monitor washing machine.
< Function Application >
1. Smart Remote Control Function Definition
1-1. Power On/Off Function Definition
.
1-1-2.
1-2-3. Notice Service
Power Off : Power off possible in case of machine on, reservation set & cycle
operated.
and send washing completion message when cycle starts and ends.
.
,
2. Smart Remote Control Monitoring Function : washing machine’s real time operating progress
7 / 8
Page 8
FCC Notice
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
If this equipment does cause harmful interference to radio or television reception, which can be determined by
Reorient or relocate the receiving antenna
Consult the dealer of an experienced radio/TV technician for help
.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio Communication. However, there is no guarantee that interference will not occur in a particular installation.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures :
-
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a oircuit difference from
that to which the receiver is connected.
-
NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
.
.
8 / 8
Loading...