LG MP9483SLA Installation

(A)

(B)

(C)

(D)

(E)

(F)

(G)

(H)

(B)

(A)

(C)

2.9cm

50.2cm

56.0cm +

0.8cm

44.0cm

0.2cm

55.0cm

5.0cm

FIG.1

FIG.2 FIG.3

ELECTRICAL CONNECTION

The appliance is fitted with a plug, and must only be connected to a properly installed socket outlet with earthing contact. The installation of the socket or replacement of the connecting cable must only be carried out by a qualified electrician in accordance with current regulations. If the plug is no longer accessible subsequent to installation, an all-pole disconnecting device must be present on the installation side with a contact gap of at least 3 mm.

PARTS LIST

(A) Carrier Rail 2 Each (B) Carrier Plate 1 Each (C) Leg 2 Each (D) Trim Assembly 1 Each (E) Bracket-U/L 2 Each (F) Bracket-Right 3 Each (G) Bracket-Left 3 Each (H) Fasten Screw 24 Each

* For (H) there may be extra screws than shown above.

They are spare screws for possible future use.

DIMENSIONS OF THE INSTALLATION OPENING

The following opening dimensions in centimeters must be available in the installation cabinet (Fig 1): HEIGHT: 44.0~45.0( ± 0.2), WIDTH : 56.0( ± 0.8), DEPTH : at least 55.0

INSTALLATION OF THE CARRIER PLATE

1. Place the carrier plate(B) in the installation cabinet. Make sure that a distance of

2.9 cm is maintained from each of the sidewalls and the front edge of the carrier plate coincides with that of the installation cabinet.

2. Lay the two carrier rails(A) onto the carrier plate(B). Now attach to the cabinet floor with the fastening screws(H) through the holes marked on the carrier plate with “Y”.

INSTALLATION OF THE OVEN

1. Fasten the leg (C) in exchange for ‘Barrier-Base’ fastened on 'Base Plate' of the oven like Fig. 3.

2. Push the main plug of the oven through the opening (P) in the installation cabinet.

3. Place the oven onto the carrier rails so that the oven’s ‘legs’ fit in the the depressions of carrier rails.

-2- -3-

INSTALLATION OF THE OVEN FRAME SCREEN

1. Attach Bracket-U/L (E) to the cabinet center and fasten screws (H) through the holes of Bracket-U/L (E) like Fig (4).

2. Attach Bracket-Right (F) and Bracket-Left (G) to the cabinet and fasten screws (H) through the holes of Bracket like Fig (4).

3. Position all Bracket (E), (F), (G) refer to the dimention in the Fig(4).

4. Attach Trim Assembly (D) to the cabinet by joining hooks of Trim Assembly (D) with Bracket (E), (F), (G).

INSTRUCTIONS FOR THE INSTALLATION OF

THE OVEN FRAME

PLEASE READ CAREFULLY BEFORE INSTALLATION

1. The cabinet which is used for the installation of the oven should be securely attached to the back panel to ensure stability.

2. The cabinet is to be used for the oven with a maximum weight of approximately 30kg.

3. If the oven is installed directly above a refrigerator or freezer cabinet, pay attention to their installation instructions and a ventilation duct must also be in place.

4. If the oven is installed directly above an electric built in oven, the appropriate electric oven installation guide must be observed. CAUTION: In the case of frequent or particularly long grill operation of the electric oven (especially with door open), the shape and colour of the oven and the oven frame can be changed.

5. It is necessary to bore a hole according to FIG 1(P) in order to connect the oven main plug to a socket (according to instructions).

6. If the oven is used again as a table appliance, all oven detachable accessories must be removed.

7. The oven should not be used as a storage place for food, cooking utensils etc. In the case of misuse, damages or hazards can occur.

8. If a fault occurs to an electronic or electrical component, the oven can only be turned off by pulling out the main plug or appropriate circuit breaker (upstream automatic fuse).

P/No. : 3828W5U0301 Printed in korea

(F)

(G)

(H)

(D)

(H)

(E)

(H)

574.0mm 1.0mm

418.0mm 2.0mm

170.0mm 1.0mm

(G)

(H)

(G)

(H)

(F)

(H)

(F)

(H)

FIG.4

(H)

-4- -1-