LG MB24AHNH0, MB18AHNH0 User Manual [fr]

www.lg.com

OWNER’S MANUAL

AIR CONDITIONER

Please read this manual carefully before operating your set and retain it for future reference.

TYPE : MULTI

The equipment complies with requirements of the Technical Regulation, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.

P/NO : 3828A20394J

ENGLISH

ITALIANO

ESPAÑOL

FRANÇAIS DEUTSCH

2 Multi Type Air Conditioner

Multi Type Air Conditioner Ownerʼs Manual

TABLE OF CONTENTS

FOR YOUR RECORDS

Write the model and serial numbers here:

Model # Serial #

You can find them on a label on the side of each unit.

Dealer's Name Date Purchased

n Staple your receipt to this page in the event you need

it to prove date of purchase or for warranty issues.

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner.

You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call for service at all.

PRECAUTION

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by young children or invalids without supervision.

• Young children should be supervised to ensure that they do not play with the air conditioner.

• When the power cord is to be replaced, replacement work shall be performed by authorized personnel only using only genuine replacement parts.

• Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only.

Safety Precautions.........................3

Operating Instructions...................6

Care and maintenance.................24

Before you call for service... .......26

Owner's Manual 3

Safety Precautions

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified

by the following indications.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

n Meanings of symbols used in this manual are as shown below.

Be sure not to do.

Be sure to follow the instruction.

n Installation

Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.

• There is risk of fire or electric shock.

For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.

• Do not disassemble or repair the product. There is risk of fire or electric shock.

Always ground the product.

• There is risk of fire or electric shock.

Install the panel and the cover of control box securely.

• There is risk of fire or electric shock.

Always install a dedicated circuit and breaker.

• Improper wiring or installation may cause fire or electric shock

Use the correctly rated breaker or fuse.

• There is risk of fire or electric shock.

Do not modify or extend the power cable.

• There is risk of fire or electric shock.

Do not install, remove, or re-install the unit by yourself (customer).

• There is risk of fire, electric shock, explosion, or injury.

Be cautious when unpacking and installing the product.

• Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and evaporator.

For installation, always contact the dealer or an Authorized Service Center.

• There is risk of fire, electric shock, explosion, or injury.

Do not install the product on a defective installation stand.

• It may cause injury, accident, or damage to the product.

Be sure the installation area does not deteriorate with age.

• If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury.

n Operation

4 Multi Type Air Conditioner

Safety Precautions

Do not plug or unplug the power supply plug during operation.

• There is risk of fire or electric shock.

Do not touch(operate) the product with wet hands.

• There is risk of fire or electrical shock.

Do not place a heater or other appliances near the power cable.

• There is risk of fire and electric shock.

Do not let the air conditioner run for a long time when the humidity is very high and a door or a window is left open

• Moisture may condense and wet or damage furniture.

Take care to ensure that power cable could not be pulled out or damaged during operation.

• There is risk of fire or electric shock.

Do not place anything on the power cable.

• There is risk of fire or electric shock.

Do not allow water to run into electric parts.

• It may cause There is risk of fire, failure of the product, or electric shock.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Do not use the product in a tightly closed space for a long time.

• Oxygen deficiency could occur.

When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.

• Do not use the telephone or turn switches on or off. There is risk of explosion or fire

If strange sounds, or small or smoke comes from product. Turn the breaker off or disconnect the power supply cable.

• There is risk of electric shock or fire.

Stop operation and close the window in storm or hurricane. If possible, remove the product from the window before the hurricane arrives.

• There is risk of property damage, failure of product, or electric shock.

Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.)

•

There is risk of physical injury, electric shock, or product failure.

When the product is soaked (flooded or submerged), contact an Authorized Service Center.

• There is risk of fire or electric shock.

Be cautious that water could not enter the product.

• There is risk of fire, electric shock, or product damage.

Ventilate the product from time to time when operating it together with a stove, etc.

• There is risk of fire or electric shock.

Turn the main power off when cleaning or maintaining the product.

• There is risk of electric shock.

When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker.

• There is risk of product damage or failure, or unintended operation.

Take care to ensure that nobody could step on or fall onto the outdoor unit.

• This could result in personal injury and product damage.

Owner's Manual 5

Safety Precautions

ENGLISH

n Installation

n Operation

Always check for gas (refrigerant) leakage after installation or repair of product.

• Low refrigerant levels may cause failure of product.

Install the drain hose to ensure that water is drained away properly.

• A bad connection may cause water leakage.

Keep level even when installing the product.

• To avoid vibration or water leakage.

Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods.

• It may cause a problem for your neighbors.

Use two or more people to lift and transport the product.

• Avoid personal injury.

Do not install the product where it will be exposed to sea wind (salt spray) directly.

•

It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or inefficient operation

Do not block the inlet or outlet of air flow.

• It may cause product failure.

Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.

• There is risk of fire, electric shock, or damage to the plastic parts of the product.

Do not touch the metal parts of the product when removing the air filter. They are very sharp!

• There is risk of personal injury.

Do not expose the skin directly to cool air for long periods of time. (Don't sit in the draft.)

• This could harm to your health.

Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air conditioner, not a precision refrigeration system.

• There is risk of damage or loss of property.

Do not step on or put anyting on the product. (outdoor units)

• There is risk of personal injury and failure of product.

Always insert the filter securely. Clean the filter every two weeks or more often if necessary.

•

A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage.

Do not insert hands or other objects through the air inlet or outlet while the product is operated.

• There are sharp and moving parts that could cause personal injury.

Do not drink the water drained from the product.

• It is not sanitary and could cause serious health issues.

Use a firm stool or ladder when cleaning or maintaining the product.

• Be careful and avoid personal injury.

Replace the all batteries in the remote control with new ones of the same type. Do not mix old and new batteries or different types of batteries.

• There is risk of fire or explosion

Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire.

• They may burn or explode.

If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not use the remote if the batteries have leaked.

• The chemicals in batteries could cause burns or other health hazards.

6 Multi Type Air Conditioner

Operating Instructions

Display temperature can be different from actual room temperature if the remote controller is installed at the place where sun-rays are falling directly or the place nearby heat source.

Plasma

Signal Receiver

RESET

Timer Cancel

Program Week Holiday

SET/CLR

MinHour

Humidify

AUTO

AUTO SWING

JET

OPERATION

FAN SPEED

Program set

SUB FUNCTION

SET TEMP

Room Temp

HI MED LO

Heater Defrost Filter

Preheat

Out door

Timer

On Set no. Time

Off

01 03 05 07 09 11 13 15 17 19 21 23

Time

Operation unit

7 8

10 11

12 13

ZONE

1234

Duct Type Remote Controller

1. Operation display

Displays the operation conditions.

2. On/Off Button

Operation starts when this button is pressed, and stops when the button is pressed again.

3. Set Temperature Button

Used to set the temperature when the desired temperature is obtained.

4. FAN Operation Button

Used to circulate room air without cooling or heating.

5. Fan Speed Button

Used to set desired fan speed.

6. Operation Mode Selection Button

Used to select the operation mode.

• Auto Operation Mode.

• Cooling Operation Mode.

• Soft Dry Operation Mode.

• Heating Operation Mode.(except cooling model)

7. Timer Cancel Button

Used to cancel the timer.

8. Timer Set Button

Used to set the timer when the desired time is obtained.

9. Week Button

Used to set a day of the week.

10. Program Button

Used to set the weekly timer.

11. Holiday Button

Used to set a holiday of the week.

12. Time Set Button

Used to set the time of the day and change the time in the weekly timer Function.

13. Set and Clear Button

Used to set and clear the weekly timer.

14. Room Temperature Checking Button

Used to check the room temperature.

15. Reset Button

Used to set the current time and clear the setting time.

Name and Function of Remote Controller

Owner's Manual 7

Operating Instructions

ENGLISH

Timer

Program

Hour

Cancel 2ndF

Week Holiday

Set/Clr

Min

RESET

PLASMA

AUTO

ZONE

1234

Operation unit

Humidify

JET SLo

AUTO

AUTO SWING OPERATION

FAN SPEED

Program set

SUB FUNCTION

SET TEMP

Room Temp

HI MED LO

Heater Defrost Filter

Preheat

Out door

Time

Timer

On Set no. Time

Off

01 03 05 07 09 11 13 15 17 19 21 23

2ndF

No Func

Signal receptor

8 9

10 11

12 13

1. Operation display

Displays the operation conditions.

2. On/Off Button

Operation starts when this button is pressed, and stops when the button is pressed again.

3. Set Temperature Button

Used to set the temperature when the desired temperature is obtained.

4. FAN Operation Button

Used to circulate room air without cooling or heating.

5. Fan Speed Button

Used to set the desired fan speed.

6. Operation Mode Selection Button

Used to select the operation mode.

• Auto Operation Mode

• Cooling Operation Mode

• Soft Dry Operation Mode

• Heating Operation Mode(except cooling model)

7. Room Temperature Checking Button

Used to check the room temperature.

8. Timer Cancel Button

Used to cancel the timer.

9. Timer Set Button

Used to set the timer when the desired time is obtained.

10. Week Button

Used to set a day of the week.

11. Program Button

Used to set the weekly timer.

12. Holiday Button

Used to set a holiday of the week.

13. Time Set Button

Used to set the time of the day and change the time in the weekly timer Function.

14. Set and Clear Button

Used to set and clear the weekly timer.

15. Reset Button

Used to set the current time and clear the setting time.

'06 MODEL : AMNH09GB1A0, AMNH12GB1A0, AMNH18GB2A0, AMNH24GB2A0

Name and Function of Remote Controller('06 Model)

8 Multi Type Air Conditioner

Operating Instructions

A/CL

Optional Function

• WIRELESS REMOTE CONTROLLER

This air-conditioner is equipped with wired remote controller basically. But if you want to have the wireless remote controller, you pay for it.

CAUTION : for handling the Remote Controller

• Aim at the signal receptor on the wired remote controller so as to operate.

• The remote control signal can be received at a distance of up to about 7m.

• Be sure that there are no obstructions between the remote controller and the signal receptor.

• Do not drop or throw the remote controller.

• Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any other heat source.

• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp)

Signal transmitter

Transmits the signals to the signal receptor.

1. FAN Operation Button

Used to circulate room air without cooling or heating.

2. Cooling Operation Button

3. Soft Dry Operation Button

Used to dehumidify without overcooling.

4. Heating Operation Button

(Heat pump model only)

5. Timer Set Button

Used to set the timer when the desired time is obtained. Then the wired remote controller is set up to 24 hours by an hour but the wireless remote controller is set up to 7 hours by an hour. Therefore, if you want to set over 7 hours, use the wired remote controller.

6. Fan Speed Button

Used to set the desired fan speed.

7. On/Off Button

Operation starts when this button is pressed, and stops when the button is pressed again.

Set Temperature Button

Used to set the temperature when the desired temperature is obtained

Auto Operation Button

10.

Plasma Air Clean Button(Optional)

11.

Electric Heater Button(Optional)

Used to set the

Electric Heater.

Owner's Manual 9

ENGLISH

Operating Instructions

ON OFF

SET

CANCEL

6 8

Optional Function('06 Model)

• WIRELESS REMOTE CONTROLLER

This air-conditioner is equipped with wired remote controller basically. But if you want to have the wireless remote controller, you pay for it.

CAUTION : for handling the Remote Controller

• Aim at the signal receptor on the wired remote controller so as to operate.

• The remote control signal can be received at a distance of up to about 7m.

• Be sure that there are no obstructions between the remote controller and the signal receptor.

• Do not drop or throw the remote controller.

• Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any other heat source.

• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp)

'06 MODEL : AMNH09GB1A0, AMNH12GB1A0, AMNH18GB2A0, AMNH24GB2A0

Signal transmitter

Transmits the signals to the signal receptor.

1. OPERATION MODEL SELECTION BUTTON

Used to select the operation mode

2. FAN SPEED BUTTON

Used to set the desired fan speed.

3. ROOM TEMPERATUR BUTTON

Used to set desired horizontal airflow direction.

4. ON/OFF BUTTON

Operation start when this button is pressed, and stops when the button is pressed again.

5. SET TEMPERATURE BUTTON

Used to set the temperature when the desired temperature is obtained.

6. ON/OFF TIMER BUTTON

Used to set time of starting operation.

7. SLEEP MODE AUTO BUTTON

Used to set sleep mode auto operation.

8. TIME SETTING BUTTON

9. AIR CIRCULATION BUTTON

Used to circulate the room air without cooling or heating.

10. TIME SET/CANCEL BUTTON

11. RESET

+ 18 hidden pages