LG M4715CG Users manual

Download

Order Number : GETEC-C1-09-159 FCC Class B Certification Test Report Number : GETEC-E3-09-084 Page 1 / 1

APPENDIX G

: USER’S MANUAL

EUT Type: LCD Monitor

FCC ID.: BEJM4715CG

User’s Guide

M4715C

Make sure to read the

Keep the User's Guide(CD) in an accessible place for future reference.

Safety Precautions

before using the product.

See the label attached on the product and give the information to your dealer when you ask

for service.

Sellers or users should understand that this device is for public use, not home use.

Connecting

- Only on some models.

the stand

1. Take the parts for the stand out of the box and assemble them as

shown in the picture.

Parts

Screws (4)

First, check if the following parts are all present.

Stand (1)

cable management (1)

2. Place a soft cloth on the table and put the product with the screen

facing downward. Connect the stand as shown in the following picture.

3. Use the screws to secure the stand on the rear side of the product as shown

in the diagram.

Connecting the Speakers

- Only on some models.

Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable.

After installing your speakers, use holders and cable ties to organize the speaker cables.

Cable holder

Remove the paper.

* This feature is not available in all model.

Cable tie

* This feature is not available in all model.

When the speaker is installed.

*Connect the input terminal with a proper color match.

To install Portrait

- Only on some models.

"When installing Portrait, rotate it clockwise based on its front."

Using the Remote Control

Name of the Remote Control Buttons

•

AV Button

•

When watching AV, RGB PC,HDMI/DVI,

The product will be automatically turned

off after a certain period of time.

Press this button repetitively to

select an appropriate time duration

- Toggles through preset video

Sleep Button

Component

•

PSM Button

settings.

1 2 3

4 5 6

•

Power On/Off Button

•

Input Select Button (See next page)

•

ARC button

Aspect Ratio Correction. Toggles through aspect ratio options.

•

Auto Button

Automatic adjustment function (Operational for the analog signal only)

There is not a function which is supported

There is not a function

which is supported

•

Menu Button

•

UP and Down buttons

Bring up and down direction

adjustment.

•

Mute button

7 8

There is not a function which is supported

•

Exit Button

•

Volume Button

Volume up and down

•

Check Button

There is not a function which is supported

Using the Remote Control

1 2 3

4 5 6

7 8

•

AV Button

•

Input Select Button

Toggles through video

AV Component RGB PC HDMI/DVI

If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button.

Input

Component RGB PC HDMI/DVI

Inserting batteries into remote control.

1. Slide off the battery cover.

2. Insert the batteries with correct polarity (+/-).

3. Close the battery cover.

• Dispose of used batteries in the recycle bin to prevent environmental pollution.

AAA Type

Name and Function of the Parts

AV IN/OUT

* The product image in the user’s guide could be different from the actual image.

Rear View

Power Connector : Connect the power cord

RS-232C Serial Ports

RGB PC, HDMI/DVI Ports

-HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals.

PC Sound Jack

: Connect the audio cable to the *LINE OUT jack of the PC sound card.

Wired Remote Control Port

AV Ports

LAN Port

Speaker Ports

*LINE OUT

A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC sound card has only Speaker Out, reduce the PC volume.

If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using the card jumper of the program (Refer to the Sound Card Manual).

AV IN/OUT

Connecting to External Devices

When Connecting to your PC

First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable.

When connecting with the D-Sub signal input cable.

When connecting with the HDMI to DVI signal input cable (not included).

* When HDMI PC is used, a compatibliy problem might occur.

Rear side of the product.

PC/

MAC

Macintosh Adapter (not included)

Use the standard Macintosh adapter since an incompatible adapter is available in the market. (Different signaling system)

MAC

Rear side of the product.

* User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain

standard compliance for the product.

(not included)

Connect the Audio cable.

Rear side of the product.

Connect the power cord.

Rear side of the product.

INPUT SET

SOURCE

AUTO/SET

Connecting to External Devices

Turn on power by pressing the power button on the product.

Turn on the PC.

SOURCE

AUTO/SET

Power button

Select an input signal. Press the INPUT button on the remote control to select the input signal.

Or, press the SOURC button on the back of the product.

Input

AV Component RGB PC

HDMI/DVI

When connecting with a D-Sub signal input cable.

• Select RGB PC : 15-pin

When connecting with a HDMI to DVI signal input cable.

• Select HDMI/DVI :

D-Sub

HDMI to DVI

analog signal.

Digital signal.

Input

AV Component

RGB PC

HDMI/DVI

Note

•

How to connect to two computers.

Connect the signal cables ( Press the INPUT button on the remote control to select the computer to use.

Directly connect to a grounded power outlet on the wall or a power bar with a ground

wire.

HDMI to DVI and D-Sub) to each computer.

Connecting to External Devices

When using the Lan

Connect the Lan cable as shown in the below figure .

When connecting with a PC.

Product

Connect the LAN cable and install the eZ-Net Manager program on the CD-ROM. For more information about the program, please refer to eZ-Net Guide in the enclosed CD-ROM.

When connecting with a Network.

Product

Network

Note

• Using LAN establishes communication between your PC and the monitor and enables to use the OSD menus on the PC as well as on the monitor.

RGB IN

RGB OUT

RGB IN

RGB OUT

RGB IN

RGB OUT

RGB IN

RGB OUT

Connecting to External Devices

Daisy Chain Monitors

Use this function when displaying ANALOG RGB inputs of a PC to the other product.

•

To use different products connected to each other

Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products.

15-pin D-Sub Signal Cable

Note

Product 1

Product 2

• When multi-connecting in/out cascade format, no loss cables are recommended.

Product 3

Product 4

We recommend that you should use cable distributor.

Connecting to External Devices

VESA FDMI wall Mounting

This product supports a VESA FDMI compliant mounting interface. These mounts are purchased separately and not available from LG. Refer to the instructions included with wall mount for more info.

The Set is equipped with a kensington Security System connector on the back panel. The cable and lock are available separate and are not sold by LG. For more info, visit http://www.kensington.com, the internet home page of the Kensington company.

Connecting to External Devices

AUDIO

AV IN/OUT

INPUT SET

SOURCE

AUTO/SET

AUDIO

AV IN/OUT

Video Input

Connect the video cable as shown in the below figure and then connect the power cord (See page 7).

When connecting with a BNC cable.

•

Connect the input terminal with a proper color match.

When connecting with a S-Video cable.

•

Connect to the S-Video input terminal to

watch high image quality movies.

Product

BNC Cable

(not included)

Product

Audio Cable

(not included)

VCR/DVD Receiver

Audio Cable

(not included)

VCR/DVD Receiver

Select an input signal. Press the INPUT button on the remote control to select the input signal.

Or, press the SOURC button on the back of the product.

When connecting with an BNC cable.

Select AV.

•

When connecting with an S-Video cable.

•

Select AV.

Input

Component RGB PC HDMI/DVI

S-Video Cable

(not included)

Note

• When the BNC cable is connected simultaneously with S-Video cable, S-Video input has a priority.

AUDIO

INPUT SET

SOURCE

AUTO/SET

Connecting to External Devices

Component Input (

480p/576p/720p/1080p/1080i/480i/576i)

Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 7).

•

Connect the input terminal with a proper color match.

Product

BNC Cable

(not included)

Audio Cable

(not included)

Note

- Some devices may require HDCP in order to display HD signals.

- Component doesn't support HDCP.

Select an input signal. Press the INPUT button on the remote control to select the input signal.

Or, press the SOURC button on the back of the product.

Select Component

•

HDTV Receiver

Input

Component

RGB PC HDMI/DVI

INPUT SET

SOURCE

AUTO/SET

Connecting to External Devices

HDMI Input (480p/576p/720p/1080i/1080p)

-HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals.

Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 7).

HDMI/DVI IN

Product

RGB IN

RGB OUT

HDMI to DVI Signal Cable

(not included)

VCR/DVD/Set-top Box

AUDIO (RGB/DVI)

REMOTE

CONTROL IN

RCA-PC Audio Cable

Product

HDMI/DVI IN

RGB IN

AUDIO

(RGB/DVI)

REMOTE

RGB OUT

CONTROL IN

HDMI Signal Cable

(not included)

VCR/DVD/Set-top Box

Note : Dolby Digital is not supported.

Select an input signal. Press the INPUT button on the remote control to select the input signal.

Or, press the SOURC button on the back of the product.

When connecting with a HDMI to DVI signal input cable. When connecting with a HDMI signal input cable.

• Select HDMI/DVI

Input

AV Component RGB PC

HDMI/DVI

AUDIO

AV IN/OUT

Connecting to External Devices

Watching

- When using AV input, you can connect the AV Out to other monitors.

AV Outputs

BNC Cable

(not included)

Video/TV

Audio Cable (not included)

Product

Note

BNC Cable

(not included)

• When multi-connecting in/out cascade format, no loss cables are recommended.

We recommend that you should use cable distributor.

Audio Cable (not included)

Video/TV

Cable management

- Only on some models.

Arrange the cables in the center as shown in the following picture.

Fit the cable guide to the back to help manage the cables.

cable management

Removing the cable guide.

Hold the Cable management with both hands and pull it downward.

Warning

• Do not use the cable management as a handle for the Monitor.

User Menus

Screen Adjustment options

Power Button

Power Indicator

MENU Button

OSD Select /

Adjust Button

SOURCE

• Press this button to turn on the power. Press this button again to

turn it off.

• This Indicator lights up blue when the display operates normally(on mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber.

• Use this button to show/hide the OSD (On Screen Display) menu screen.

• Use

this

button to select an icon or adjust the setting in the OSD screen.

• Adjust the up and down.

AUTO/SET

• Adjust the volume.

Volume

Troubleshooting

No image is displayed

●

Is the product power cord connected?

●

Is the power indicator light on?

●

Power is on, power the screen appears extremely dark.

●

the power indicator amber?

●

Does the 'Out of range' message appear?

indicator

is blue but

• See if the power cord is properly connected to the outlet.

• See if the power switch is turned on.

• May need service.

• Adjust brightness and contrast again.

• Backlight may need repair.

• If the product is in power saving mode, move the

mouse or press any key.

• Turn both devices off and then back on.

• The signal from the PC (video card) is out of the

vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual.

* Maximum resolution

RGB : 1920 x 1080 @60Hz HDMI/DVI : 1920 x 1080 @60Hz

●

Does the 'Check signal cable' message appear?

• The signal cable between PC and product is not

connected. Check the signal cable.

• Press the 'INPUT' menu in the remote Control to

check the input signal.

'Unknown Product' message appears when the product is connected.

●

Did you install the driver?

• Install the product driver, which is provided with

the product, or download it from the web site. (http://www.lge.com)

• See if the plug&play function is supported by

referring to the video card user manual.

' Key Lock On' message appears.

●

The 'Key Lock On' message appears when pressing the Menu button.

Note

* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times

every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. The unit is Hz.

* Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the

horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz.

• The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button

▲

and button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only.)

The screen image looks abnormal.

●

Is the screen position wrong?

●

Do thin lines appear on the

background screen?

●

Horizontal noise appears or the

characters look blurred.

Troubleshooting

• D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu.

• See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel – Display – Setting menu.

• D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OSD menu.

●

The screen is displayed abnormally.

After-image appears on the product.

●

After-image appears when the product is turned off.

• The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal.

• If you use a fixed image for a long time, the pixels

may be damaged quickly. Use the screen-saver function.

Troubleshooting

The audio function does not work.

●

No sound?

●

Sound is too dull.

●

Sound is too low.

Screen color is abnormal.

●

Screen has poor color resolution

(16 colors).

●

Screen color is unstable or monocolored.

●

Do black spots appear on the screen?

• See if the audio cable is connected properly.

• Adjust the volume.

• See if the sound is set properly.

• Select the appropriate equalize sound.

• Adjust the volume.

• Set the number of colors to more than 24 bits (true

color) Select Control Panel – Display – Settings – Color Table menu in Windows.

• Check the connection status of the signal cable. Or, re-insert the PC video card.

• Several pixels (red, green, white or black color)

may appear on the screen, which can be attributable to the unique characteristics of the LCD panel. It is not a malfunction of the LCD.

The operation does not work normally.

●

The power suddenly turned off.

• Is the sleep timer set?

• Check the power control settings.

Power interrupted.

•

"CAUTION! FAN STOP!" If the power is turned off after this message appears, it means that the fan is out of order.

In this case, contact your local service center.

Specifications

The product specifications can change without prior notice for product improvement.

LCD Panel

Power

Dimensions

&Weight

46.96 inches (119.28 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 119.28 cm

0.5415 mm x 0.5415 mm (Pixel Pitch)

Rated Voltage AC 100-240V~ 50/60Hz 3.0A Power Consumption On Mode : 300W Typ.

Sleep Mode : ≤ 1W (RGB) / 4W(HDMI/DVI) (If LAN OFF is selected) Off Mode : ≤ 1W

[1]

[3]

[2]

[4]

Width x Height x Depth

[1] 111.70 cm (43.98 inches) x 75.78 cm (29.83 inches) x 30.26 cm (11.91 inches) [2] 111.70 cm (43.98 inches) x 66.10 cm (26.02 inches) x 11.87 cm (4.67 inches) [3] 111.70 cm (43.98 inches) x 75.78 cm (29.83 inches) x 30.26 cm (11.91 inches) [4] 111.70 cm (43.98 inches) x 66.10 cm (26.02 inches) x 11.87 cm (4.67 inches)

Net [1] 32.82 kg (72.35 lbs) [2] 28.80 kg (63.5 lbs) [3] 33.56 kg (74 lbs) [4] 29.55 kg (65.15 lbs)

NOTE

Information in this document is subject to change without notice.

Specifications

The product specifications can change without prior notice for product improvement.

Video Signal

Input Connector

Environmental Conditions

Max. Resolution RGB : 1920 X 1080 @60Hz

HDMI/DVI :

Recommended Resolution

Horizontal Frequency RGB : 30 - 83 kHz

Vertical Frequency RGB : 56 - 75 Hz

Synchronization Type Composite/Separate/Digital

Operational Condition Temperature: 0˚C ~ 40˚C , Humidity: 10% ~ 80% Storage Condition Temperature: -20˚C ~ 60˚C , Humidity: 5% ~ 90%

RGB : WSXGA 1360 X 768@60Hz HDMI/DVI : WSXGA 1360 X 768 @60Hz – It may not be

supported depending on the OS or video card type.

HDMI/DVI : 30 - 83 kHz

HDMI/DVI : 56 - 60 Hz

15-pin Composite Video, Component, RS-232C, LAN

1920 X 1080

D-Sub type, HDMI (digital), S-Video,

* Applicable only for models that support the speakers

RMS Audio Output 10W+10W(R+L)

Audio

Input Sensitivity 0.7Vrms Speaker Impedance 8Ω

@60Hz – It may not be supported

depending on the OS or video card type.

NOTE

Information in this document is subject to change without notice.

Specifications

PC Mode – Preset Mode

Horizontal

Preset mode

1 2

6 7

*10

640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600

832 x 624 1024 x 768 1024 x 768 1280 x 720

Frequency

31.469

31.468

31.469

37.5

37.879

46.875

49.725

48.363

60.123

44.772

DTV Mode

Component

480i o x 576i o x 480p o o 576p o o 720p o o 1080i o o 1080p o o

HDMI/DVI(DTV)

(kHz)

Vertical

Frequency

(Hz)

70.8

59.94 75

60.317 75

74.55 60

75.029

59.855

Preset mode

*11 *12 *13 *14

1280 x 1024

*16

1680 x 1050

*17

1920 x 1080

1280 x 768 1360 x 768 1366 x 768

Horizontal Frequency

(kHz)

47.7

47.72

47.7

63.981

79.98

65.290

67.5

1~17: RGB Mode

* : HDMI/DVI mode

Vertical

Frequency

(Hz)

59.799 60

60.02

75.02

59.954 60

Power

On Mode Sleep Mode Off Mode

Indicator

Mode

Product

Blue

Amber

NOTE

DTV/PC selection on RGB and HDMI/DVI inputs is available for PC resolutions : 640 X 480/60Hz, 1280 X 720/60Hz, 1920 X 1080/60Hz and DTV resolutions : 480p, 720p, 1080p.

RS-232C

Controlling the Multiple Product

Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC.

Connecting the cable

Connect the RS-232C cable

* The RS-232C protocol is used for communication between the PC and product. You can

turn the product on/off, select an input source or adjust the OSD menu from your PC.

RS-232C Cable (not included)

as shown in the picture.

monitor 1

RS-232C Configurations

7-Wire Configurations (Standard RS-232C cable)

PC Monitor

RXD

TXD

GND

DTR

DSR

RTS

CTS

D-Sub 9 D-Sub 9

(Female) (Female)

TXD

RXD

GND

DSR

DTR

CTS

RTS

Communication Parameter

▲

Baud Rate : 9600buad Rate (UART)

▲

Data Length : 8bits

▲

Parity Bit : None

▲

Stop Bit : 1bit

▲▲

Flow Control : None Communication Code : ASCII code

▲

Use a crossed (reverse) cable

monitor 2

monitor 3 monitor 4

3-Wire Configurations (Not Standard)

PC Monitor

RXD

TXD

GND

DTR

DSR

RTS

CTS

D-Sub 9 D-Sub 9

(Female) (Female)

TXD

RXD

GND

DTR

DSR

RTS

CTS

RS-232C

Controlling the Multiple Product

Command Reference List

COMMAND1 COMMAND2 DATA1 DATA2 DATA3

01. Power k a 00H - 01H

02. Input Select k b 02H - 09H

03. Aspect Ratio k c 01H - 09H

04. Screen Mute k d 00H - 01H

05. Volume Mute k e 00H - 01H

06. Volume Control k f 00H - 64H

07. Contrast k g 00H - 64H

08. Brightness k h 00H - 64H

09. Color k i 00H - 64H

10. Tint k j 00H - 64H

11. Sharpness k k 00H - 64H

12. OSD Select k l 00H - 01H

13. Remote Lock/ key Lock k m 00H - 01H

14. Balance k t 00H - 64H

15. Color Temperature k u 00H - 03H

16. Abnormal state k z FFH

17. ISM mode j p 00H - 10H

18. Auto configuration j u 01H

19. Key m c Key Code

20. Tile Mode d d 00H - 55H

21. Tile H Position d e 00H - 64H

22. Tile V Position d f 00H - 64H

23. Tile H Size d g 00H - 64H

24. Tile V Size d h 00H - 64H

25. Tile ID Set d i 00H - 19H Natural Mode (In Tile mode)

26.

27. Picture mode(PSM) d x 00H - 06H

28. Sound mode d y 00H - 06H

29. Fan Fault check d w FFH

30. Elapsed time return d l FFH

31. Temperature value d n FFH

32. Lamp fault check d p FFH

33. Auto Volume d u 00H - 01H

34. Speaker d v 00H - 01H

35. Time f a 00H - 06H 00H - 17H 00 - 3BH On Timer (On/Off Timer) On, Off

36. Off Timer (On/Off Timer) On, Off

37. On Timer (On/Off Timer) Time

38. Off Timer (On/Off Timer) Time

39. Sleep Time

40.

41. Auto Sleep f g 00H - 01H

42. Power On Delay f h 00H - 64H

43. Language f i 00H - 09H

44. DPM Select f j 00H - 01H

45. Reset f k 00H - 02H

d j 00H - 01H

f b 00H, FFH 00H - FFH f c 00H, FFH 00H - FFH f d 00H - 07H 00H - 17H 00 - 3BH f e 00H - 07H 00H - 17H 00 - 3BH f f 00H - 08H

RS-232C

46. Power Saving f l 00H - 03H

47. Power Indicator f o 00H - 01H

48. H Position f q 00H - 64H

49. V Position f r 00H - 64H

50. H Size f s 00H - 64H

51. V Size f t 00H - 64H

52. Scheduling input select f u 00H - 07H 00H - FEH

53. Serial no. f y FFH

54. S/W Version f z FFH

55. Input Select x b 20H - A0H

Controlling the Multiple Product

COMMAND1 COMMAND2 DATA1 DATA2 DATA3

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: First command. (k) * [Command 2]: Second command.(a ~ u) * [Set ID]: Set up the Set ID number of product.

range : 01H~63H. by setting '0', server can control all products. * In case of operating with more than 2 sets using set ID as '0' at the same time, it should not be checked the ack message. Because all sets will send the ack message, so it's impossible the check the whole ack messages.

* [DATA]: To transmit command data.

Transmit 'FF' data to read status of command.

* [Cr]: Carriage Return

ASCII code ‘0x0D’

* [ ]: ASCII code Space (0x20)’

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The Product transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the

data is data read mode, it indicates present status data.

If the data is data write mode, it returns the data of the PC

computer.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* If there is error, it returns NG

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

03. Aspect Ratio(Command : c) (Main picture format)

▲

To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu.

Transmission

[k][c][ ][Set ID][ ][Data][Cr]

Data 1 : Normal Screen (4:3)

2 : Wide Screen (16 :9) 4 : Zoom1 (AV) 5 : Zoom2 (AV) 6 : Original (AV) 7 :14:9 (AV) 9 : Just Scan(HD DTV), 1:1 (RGB PC, HDMI/DVI PC)

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute(Command : d)

▲

To select screen mute on/off.

Transmission

[k][d][ ][Set ID][ ][Data][Cr]

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

14 Balance(Command : t)

▲

To adjust the sound balance.

Transmission

[k][t][ ][Set ID][ ][Data][Cr]

Data Min : 00H ~ Max : 64H

(Hexadecimal code)

•

Refer to ‘Real data mapping’ page A8.

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

Data Min : 00H ~ Max : 64H * Balance : L50 ~ R50

15. Color Temperature (Command : u)

▲

To adjust the screen color temperature.

Transmission

[k][u][ ][Set ID][ ][Data][Cr]

Data 0 : Medium

1 : Cool 2 : Warm

3 : User

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

Data 0 : Medium

1 : Cool 2 : Warm

3 : User

•

Running the Color Temperature command changes the Picture Mode settings to User1.

A11

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

16. Abnormal state (Command : z)

▲

Abnormal State : Used to Read the power off status when Stand-by mode.

Transmission

[k][z][ ][Set ID][ ][Data][Cr]

Data FF : Read

0 : Normal (Power on and signal exist) 1 : No signal (Power on) 2 : Turn the monitor off by remote control 3 : Turn the monitor off by sleep time function 4 : Turn the monitor off by RS-232C function 8 : Turn the monitor off by off time function 9 : Turn the monitor off by auto off function

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

17. ISM mode(Command: j p)

▲

Used to select the afterimage preventing function.

Transmission

[j][p][ ][Set ID][ ][Data][Cr]

Data 1H : Inversion

2H : Orbiter 4H : White Wash

8H : Normal

10H : Dot Wash

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

A12

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

52. Scheduling Input select (Command : f u) (Main Picture Input)

▲

To select input source for TV depending on day.

Transmission

[f][u][][Set ID][][Data1][][Data2][Cr]

Data 1 Structure

Min: 0~Max:7(0:Monday, 1: Tuesday, 2: Wednesday, 3: Thursday, 4: Friday

5: Saturday, 6: Sunday, 7: Everyday)

Data 2 Structure

Data(Hex)

02 04 07 08 09

Acknowledgement

[u][][Set ID][][OK/NG][Data 1][Data 2][x]

53. Serial no.Check (Command : f y)

▲

To read the serial numbers

Transmission

[f][y][][Set ID][][Data][Cr]

Data FF (to read the serial numbers)

Acknowledgement

[y][][Set ID][][OK/NG][Data1] ~ [Data13] [x]

* The data format is ASCII Code.

INPUT

AV Component RGB-PC HDMI/DVI-DTV HDMIDVI-PC No change

A31

RS-232C

Controlling the Multiple Product

Transmission / Receiving Protocol

54. S/W Version (Command : f z)

▲

Check the software version.

Transmission

[f][z][][Set ID][][Data][Cr]

Data FFH : Read

Acknowledgement

[z][][Set ID][][OK/NG][Data][x]

55. Input Select (Command : x b)

▲

To select input source for the Set.

Transmission

[x][b][ ][Set ID][ ][Data][Cr]

Data 20H : AV

40H : Component 60H : RGB (PC) 90H : HDMI/DVI (DTV) A0H : HDMI/DVI (PC)

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

Data 20H : AV

40H : Component

60H : RGB (PC) 90H : HDMI/DVI (DTV) A0H : HDMI/DVI (PC)

A32

RS-232C

IR Codes

▲▲▲

Connect your wired remote control to Remote Control port on the Product.

Remote Control IR Code

Output waveform

How to connect

single pulse, modulated with 37.917KHz signal at 455KHz

Carrier frequency

FCAR = 1/Tc = fosc/12

Duty ratio = T1/Tc = 1/3

Configuration of frame

•

1st frame

Lead code

•

▲

Lead code

Low custom code

C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat frame

Repeat code

9ms

High custom code

Data code

4.5ms

Data code

▲

Repeat code

9ms

•

2.25ms

Bit "1"

A33

▲

Bit description

•

Bit "0"

0.56ms

▲

Frame interval : Tf

•

The waveform is transmitted as long as a key is depressed.

1.12ms

Tf=108ms@455KHz

0.55ms

0.56ms

2.24ms

RS-232C

Code(Hex) Function Note

00 01 02 03 08 C4 C5 09 98 0B 0E 43 5B 6E 44 10 11 12 13 14 15 16 17 18 19 5A BF D5 C6 79 76 77 AF 99

▲

▼

▲

VOL( )

▲

POWER ON/OFF

POWER ON

POWER OFF

MUTE

AV INPUT SLEEP MENU EXIT PSM SET

Number Key 0

Number Key 1

Number Key 2

Number Key 3

Number Key 4

Number Key 5

Number Key 6

Number Key 7

Number Key 8

Number Key 9

AV COMPONENT RGB PC HDMI/DVI ARC ARC (4:3) ARC (16:9) ARC (ZOOM) AUTO CONFIG

R/C Button

R/C Button (Power On/Off)

Discrete IR Code(Only Power On)

Discrete IR Code(Only Power Off)

R/C Button

Discrete IR Code(Input AV Selection)

Discrete IR Code(Input COMPONENT Selection)

Discrete IR Code(Input RGB PC Selection)

Discrete IR Code(Input HDMI/DVI Selection)

R/C Button

Discrete IR Code(Only 4:3 mode)

Discrete IR Code(Only 16:9 mode)

Discrete IR Code(Only ZOOM1, ZOOM2 mode)

Discrete IR Code

IR Codes

A34

Regulatory Information cont.

FCC Compliance Statement

This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System.

Canadian DOC Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B

respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

CE Conformity Notice

(for Europe)

Products with the “CE” Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :

• EN 55022 ; Radio Frequency Interference

• EN 55024 ; Electromagnetic Immunity

• EN 61000-3-2 ; Power Line Harmonics

• EN 61000-3-3 ; Voltage Fluctuations

• EN 60950-1 ; Product Safety

Low Radiation Compliance (MPR II)

This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range.

NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements.

TCO'99 (TCO'99 applied model only)

Congratulations!

You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.

Regulatory Information cont.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized.

There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy.

What does labelling involve?

The product meets the requirements for the TCO’99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety.

Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered.

Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and

visual ergonomics.

Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Development’s website http://www.tcodevelopment.com or may be ordered from:

TCO Development

SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO’99 approved and labelled products may also be obtained at http://www.tcodevelopment.com

Ecological requirements

Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes when not disposed of in accordance with strict standards for disposal.

TCO’99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives.

Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO’99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium.

Mercury** Mercury is sometimes found in batteries, relays and switches. TCO’99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one

Regulatory Information cont.

exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available.

Lead** Lead can be found in picture tubes, display screens, solders and capacitors. TCO’99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________

* Bio-accumulative is defined as substances which

accumulate in living organisms.

**Lead, Cadmium and Mercury are heavy metals

which are bio-accumulative.

TCO’03

(TCO’03 applied model only)

Congratulations!

The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneficial both for the user and the environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001

• Restrictions on

chlorinated and brominated flame retardants and polymers

heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

Information for Environmental Preservation

LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects.

We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors.

Information for recycling

This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use.

LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in

English

Regulatory Information cont.

operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG.

We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our ‘green’ policies. http://www.lge.com/about/environment/html/Recycling.jsp

Informationen zur Erhaltung der Umwelt

Im Jahr 1994 verkündete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklärung für eine sauberere Umwelt). Seitdem dient dieses Ideal als führendes Prinzip des Unternehmens. Diese Erklärung war die Basis für die Durchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden. Wir fördern Aktivitäten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezüglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schädlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden.

Informationen zum Thema Recycling

Dieser Monitor enthält Teile, die umweltschädlich sein können. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er außer Dienst gestellt wurde.

Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rücknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schädliche Substanzen und Schwermetalle werden durch umweltverträgliche Verfahren behandelt. Falls Sie mehr über unser Recyclingprogramm erfahren möchten, wenden Sie sich bitte an Ihren lokalen LGHändler oder einen Unternehmensvertreter von LG.

Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einfließen lassen. Zusätzliche Informationen über unsere ‘grüne’ Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp

Information sur la protection del’environnement

LGE. a publié sa 'Déclaration en faveur d’un environnement plus propre' en 1994 et celle-ci est restée, depuis lors, un principe directeur de notre entreprise. Cette déclaration a servi de base à notre réflexion et nous a permis de prendre en compte à la fois les aspects économiques et sociaux de nos activités, tout en respectant l’environnement.

Nous encourageons les activités en faveur de la préservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons au minimum les matières dangereuses qui entrent dans leur composition et l’on ne trouve pas de cadmium, par exemple, dans nos moniteurs.

Information sur le recyclage

Ce moniteur peut contenir des composants qui présentent un risque pour l’environnement. Il est donc important que celui-ci soit recyclé après usage.

LGE. traite les moniteurs en fin de cycle conformément à une méthode de recyclage respectueuse de l’environnement. Nous reprenons nos produits et les recyclons dans plusieurs sites répartis dans le monde entier. De nombreux composants sont réutilisés et recyclés, et les matières dangereuses, ainsi que les métaux lourds, sont traités selon un procédé écologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un l’un de nos représentants.

Nous voulons agir pour un monde plus propre et croyons au rôle de notre entreprise dans l’amélioration de l’environnement. Pour plus de renseignements sur notre politique “verte”, rendez visite à notre site : http://www.lge.com/about/environment/html/Recycling.jsp

Deutsch

Français

Regulatory Information cont.

Informazioni per la tutela dell’ambiente

La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente più pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attività a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attività a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dell’ambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non è presente il cadmio.

Informazioni per il riciclaggio

Il monitor può presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. È importante che il monitor sia riciclato al termine del suo utilizzo.

La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dell’ambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, è consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG.

Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo più pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica “verde”. http://www.lge.com/about/environment/html/Recycling.jsp

Información para la conservación medioambiental

LGE. presentó la 'Declaración para un entorno más limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaración es la base que nos ha permitido llevar a cabo tareas que

respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, económicos y medioambientales.

Promocionamos actividades orientadas a la conservación del medio ambiente y desarrollamos nuestros productos específicamente para que se ajusten a la filosofía que protege el entorno. Reducimos al máximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores.

Información para el reciclaje

Este monitor puede contener piezas que entrañen riesgos medioambientales. Es importante reciclar este monitor después de su utilización. LGE. trata todos los monitores usados siguiendo un método de reciclaje que no daña al entorno. Contamos con diversos sistemas de recuperación y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dañinas y los metales pesados se tratan siguiendo un método que no perjudique al medio ambiente. Si desea obtener más información acerca del programa de reciclaje, póngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca.

Basamos nuestra visión y nuestras políticas en un mundo más limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolución como empresa. Visite nuestra página Web para obtener más información sobre nuestras políticas ecológicas. http://www.lge.com/about/environment/html/Recycling.jsp

Informações relacionadas à preservação ambiental

A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declaração da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde então como um princípio administrativo de orientação. A Declaração é a base que nos tem permitido realizar atividades favoráveis ao ambiente com consideração atenta aos aspectos econômicos, ambientais e sociais.

Promovemos atividades de preservação ambiental e desenvolvemos nossos produtos para englobar

Italiano

Espanõl

Português

Regulatory Information cont.

especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, não há cádmio em nossos monitores.

Informações relacionadas à reciclagem

Este monitor pode conter peças que podem representar riscos ao ambiente. É importante que ele seja reciclado após o uso.

A LGE. cuida de todos os monitores descartados através de um método de reciclagem agradável ao ambiente. Há vários sistemas de devolução e reciclagem atualmente em operação no mundo. Muitas peças serão reutilizadas e recicladas e as substâncias nocivas e os metais pesados passarão por tratamento através de um método favorável ao ambiente. Para obter mais informações sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas a um mundo mais limpo selecionando a questão do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informações sobre nossas políticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp

Informatie met betrekking tot het behoud van het milieu

LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden.

Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors.

Nederlands

Informatie met betrekking tot recycling

Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled.

LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LGvertegenwoordiger of een LG-vestiging.

Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp

»ÌÙÓÏ‡ˆËˇ ÔÓ Óı‡ÌÂ ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚

¬ 1994 „У‰Ы НУФУ‡ˆЛˇ LGE УФЫ·ОЛНУ‚‡О‡ 'ƒВНО‡‡ˆЛ˛ LG ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚', НУЪУ‡ˇ Т ЪВı ФУ ТОЫКЛЪ УТМУ‚М˚П ФЛМˆЛФУП ЫФ‡‚ОВМЛˇ. Х‡ УТМУ‚В ˝ЪУИ ‰ВНО‡‡ˆЛЛ П˚ ТПУ„ОЛ ФВ‰ФЛМˇЪ¸ ‰ВИТЪ‚Лˇ, У·ВТФВ˜Л‚‡˛˘ЛВ

·ВБУФ‡ТМУТЪ¸ УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ ФЛ ˝ЪУП

‰УОКМУВ ‚МЛП‡МЛВ ˝НУМУПЛ˜ВТНЛП, ˝НУОУ„Л˜ВТНЛП Л ТУˆЛ‡О¸М˚П ‡ТФВНЪ‡П.

Г˚ ТЪЛПЫОЛЫВП ‰ВˇЪВО¸МУТЪ¸ ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ УТУ·УВ ‚МЛП‡МЛВ ‡Б‡·УЪНВ М‡¯ВИ ФУ‰ЫНˆЛЛ ‚ ТУУЪ‚ВЪТЪ‚ЛЛ Т НУМˆВФˆЛВИ ˝НУОУ„Л˜ВТНУИ ·ВБУФ‡ТМУТЪЛ. Г˚ Т‚У‰ЛП Н ПЛМЛПЫПЫ ТУ‰ВК‡МЛВ УФ‡ТМ˚ı ‚В˘ВТЪ‚ ‚ М‡¯ВИ ФУ‰ЫНˆЛЛ. Х‡ФЛПВ, ‚ М‡¯Лı ПУМЛЪУ‡ı ‚˚ МВ М‡И‰ВЪВ Н‡‰ПЛˇ.

»МЩУП‡ˆЛˇ ФУ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚

›ЪУЪ ПУМЛЪУ ПУКВЪ ТУ‰ВК‡Ъ¸ НУПФУМВМЪ˚, НУЪУ˚В ПУ„ЫЪ М‡МВТЪЛ Ы˘В· УНЫК‡˛˘ВИ ТВ‰В.

Russian

Regulatory Information cont.

EPA

(EPA applied model only)

ENERGY STAR

is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).

NOM MARK (Mexico only)

ХВУ·ıУ‰ЛПУ ЫЪЛОЛБЛУ‚‡Ъ¸ ПУМЛЪУ ФУТОВ ЛТФУО¸БУ‚‡МЛˇ.

KУФУ‡ˆЛˇ LGE ФВВ‡·‡Ъ˚‚‡ВЪ ‚ТВ ·‡НУ‚‡ММ˚В ПУМЛЪУ˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ ФЛВПОВПУ„У ПВЪУ‰‡ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚. œУ ‚ТВПЫ ПЛЫ ‰ВИТЪ‚Ы˛Ъ ТЛТЪВП˚ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ Л ‚УБ‚‡Ъ‡ ЛТФУО¸БУ‚‡ММУИ ФУ‰ЫНˆЛЛ. ГМУ„ЛВ НУПФУМВМЪ˚

·Ы‰ЫЪ ‚ЪУЛ˜МУ ЛТФУО¸БУ‚‡М˚ Л ЫЪЛОЛБЛУ‚‡М˚, ‚ ЪУ ‚ВПˇ Н‡Н ‚В‰М˚В ‚В˘ВТЪ‚‡ Л ЪˇКВО˚В ПВЪ‡ОО˚

·Ы‰ЫЪ У·‡·УЪ‡М˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ ФЛВПОВПУ„У ПВЪУ‰‡.

«‡ ·УОВВ ФУ‰У·МУИ ЛМЩУП‡ˆЛВИ ФУ М‡¯ВИ ФУ„‡ППВ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ У·‡˘‡ИЪВТ¸ Н ПВТЪМУПЫ ФУТЪ‡‚˘ЛНЫ ЛОЛ ФВ‰ТЪ‡‚ЛЪВО˛

ÍÓÔÓ‡ˆËË LG.

Г˚ УЛВМЪЛЫВПТˇ М‡ У·ВТФВ˜ВМЛВ ˝НУОУ„Л˜ВТНУИ

·ВБУФ‡ТМУТЪЛ, ТЪ‡‚ˇ ТВ·В ˆВО¸˛ „ОУ·‡О¸МЫ˛ Б‡˘ЛЪЫ УНЫК‡˛˘ВИ ТВ‰˚. ƒУФУОМЛЪВО¸МЫ˛ ЛМЩУП‡ˆЛ˛ У М‡¯ВИ ФУОЛЪЛНВ ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚ ‚˚ ПУКВЪВ М‡ИЪЛ М‡ М‡¯ВП Т‡ИЪВ:

http://www.lge.com/about/environment/html/Recycling.jsp

As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Regulatory Information cont.

1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

Disposal of your old appliance

1.Quando su un prodotto è riportato il simbolo di

1.När den här symbolen med en överkryssad soptunna på hjul sitter på en produkt innebär det att den regleras av European Directive 2002/96/EC.

2.Alla elektriska och elektroniska produkter bör kasseras via andra vägar än de som finns för hushållsavfall, helst via för ändamålet avsedda uppsamlingsanläggningar som myndigheterna utser.

3.Om du kasserar din gamla apparat på rätt sätt så bidrar du till att förhindra negativa konsekvenser för miljön och människors hälsa.

4.Mer detaljerad information om kassering av din gamla apparat kan får av kommunen, renhållningsverket eller den butik där du köpte produkten.

1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC.

2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen.

3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen.

Smaltimento delle apparecchiature obsolete

Kassering av din gamla apparat

Uw oude toestel wegdoen

1.Ce symbole, représentant une poubelle sur roulettes barrée d'une croix, signifie que le produit est couvert par la directive européenne 2002/96/EC.

2.Les éléments électriques et électroniques doivent être jetés séparément, dans les videordures prévus à cet effet par votre municipalité.

3.Une élimination conforme aux instructions aidera à réduire les conséquences négatives et risques éventuels pour l'environnement et la santé humaine.

4.Pour plus d'information concernant l'élimination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures ménagères ou encore la magasin où vous avez acheté ce produit.

Élimination de votre ancien appareil

un bidone della spazzatura barrato da una croce significa che il prodotto è coperto dalla direttiva europea 2002/96/EC.

2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorità locali.

3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente.

4.Per informazioni più dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui è stato acquistato il prodotto.

English

French

Italian

Swedish

Dutch

WEEE (for Europe )

Regulatory Information cont.

1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC.

2.Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt werden.

3.Mit der ordnungsgemäßen Entsorgung des alten Geräts vermeiden Sie Umweltschäden und eine Gefährdung der persönlichen Gesundheit.

4.Weitere Informationen zur Entsorgung des alten Geräts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo Sie das Produkt erworben haben.

1.ŸЩ·У ¤У· ЪФ˚ﬁУ ‰И·ı¤ЩВИ ЩФ ‰‡М‚ФПФ ВУﬁ˜ ‰И·БЪ·ММ¤УФ˘ О¿П·ıФ˘ ·ФЪЪИММ¿ЩˆУ, ЩﬁЩВ ЩФ ЪФ˚ﬁУ О·П‡ЩВЩ·И ·ﬁ ЩЛУ E˘Ъˆ·˚О‹ O‰ЛБ›· 2002/96/EOK.

2.H ·ﬁЪЪИ„Л ﬁПˆУ ЩˆУ ЛПВОЩЪИОТУ О·И ЛПВОЩЪФУИОТУ ЪФ˚ﬁУЩˆУ Ъ¤ВИ У· Б›УВЩ·И ¯ˆЪИЫЩ¿ ·ﬁ Щ· БВУИО¿ ФИОИ·О¿ ·ФЪЪ›ММ·Щ· М¤Ыˆ О·ıФЪИЫМ¤УˆУ ВБО·Щ·ЫЩ¿ЫВˆУ Ы˘ППФБ‹˜ ·ФЪЪИММ¿ЩˆУ, ФИ ФФ›В˜ ¤¯Ф˘У ‰ЛМИФ˘ЪБЛıВ› В›ЩВ ·ﬁ ЩЛУ О˘‚¤ЪУЛЫЛ ‹ ·ﬁ ЩИ˜ ЩФИО¤˜ ·Ъ¯¤˜.

3.H ЫˆЫЩ‹ ·ﬁЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜ ı· ‚ФЛı‹ЫВИ ЫЩЛУ ·ФЩЪФ‹ Иı·УТУ ·ЪУЛЩИОТУ Ы˘УВИТУ ˆ˜ ЪФ˜ ЩФ ВЪИ‚¿ППФУ О·И ЩЛУ ˘БВ›· ЩФ˘ ·УıЪТФ˘.

4.°И· ИФ ПВЩФМВЪВ›˜ ПЛЪФКФЪ›В˜ Ы¯ВЩИО¿ МВ ЩЛУ

·ﬁЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜, ВИОФИУˆУ‹ЫЩВ МВ ЩФ ·ЪМﬁ‰›Ф ЩФИОﬁ БЪ·КВ›Ф, ˘ЛЪВЫ›· ‰И¿ıВЫЛ˜ ФИОИ·ОТУ

·ФЪЪИММ¿ЩˆУ ‹ ЩФ М·Б·Н› ·ﬁ ЩФ ФФ›Ф ·БФЪ¿Ы·ЩВ ЩФ ЪФ˚ﬁУ.

1.Tämä merkki tuotteessa tarkoittaa, että tuote kuuluu sähkö- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan.

2.Kaikki elektroniset laitteet ovat ongelmajätettä,

joten ne on toimitettava paikalliseen keräyspisteeseen.

3.Vanhan laitteen asianmukainen hävittäminen

ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.

4.Lisätietoa vanhan laitteen hävittämisestä saat

ottamalla yhteyden paikallisiin viranomaisiin, kierrätyskeskukseen tai myymälään, josta ostit laitteen.

1.Når der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC.

2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjælp af specielle indsamlingsfaciliteter, der er organiseret af staten

1.Si en un producto aparece el símbolo de un contenedor de basura tachado, significa que éste se acoge a la Directiva 2002/96/CE.

2.Todos los aparatos eléctricos o electrónicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a través de puntos de recogida designados por el gobierno o las autoridades locales.

3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pública.

4.Para obtener más información sobre cómo deshacerse de sus aparatos eléctricos y electrónicos viejos, póngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquirió el producto.

Vanhojen laitteiden hävittäminen

Entsorgung von Altgeräten

Sådan smider du dit gamle apparat ud

∞ﬁÚÚÈ„Ë ÙË˜ ·ÏÈ¿˜ Û·˜ Û˘ÛÎÂ˘‹˜

Cómo deshacerse de aparatos eléctricos y electrónicos viejos

eller de lokale myndigheder.

3.Korrekt bortskaffelse af dit gamle apparat er med

til at forhindre mulige skadevirkninger på miljøet og menneskelig sundhed.

4.Mere detaljerede oplysninger om bortskaffelse af

dit gamle apparat kan fås ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du købte produktet.

Finnish

German

Danish

Greek

Spanish

4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht.

Regulatory Information cont.

Portuguese

Slovak

Czech

Croatian

Hungarian

Polish

Regulatory Information cont.

Estonian

Latvian

Lithuanian

LG M4715CG Users manual

Specifications and Main Features

Frequently Asked Questions

User Manual