APPENDIX H
: USER’S MANUAL
Test Report Number: GETEC-E3-08-042
FCC Class B Certification
EUT Type: LCD Monitor
FCC ID: BEJM2294AJ
User’s Guide
M1994A
M2294A
Make sure to read the
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your dealer when you ask for
service.
Safety
Precautions before using the product.
Before Connecting to the PC
Stand Installation
Before setting up the product, ensure that the power supply, the computer system,
and other attached devices is turned off.
Carefully place the product screen side
1
down on a cushioned surface that will
protect product and screen from damage.
Insert the stand base into the product
2
Attach the monitor to the Stand Base
3
by turning the screw to the right.
* Turn the screw by using the screw
handle
Screw
1
Before Connecting to the PC
Detaching Stand
Before setting up the product, ensure that the power supply, the computer system,
and other attached devices is turned off.
Place the set screen side down on a
1
cushion or soft cloth.
Turn the screw by using the screw handle
3
Detach the monitor to the Stand
2
Base by turning the screw to the left.
Pull the stand base.
4
5
2
Before Connecting to the PC
Before setting up the product, ensure that the power supply, the computer system,
and other attached devices is turned off.
Positioning your display
1.
Adjust the position of the panel in various ways for maximum comfort.
Tilt Range
-5°~ -2
°
12°~ 18
°
Warning:
When adjusting the angle of the screen, do not put
your finger(s) in between the head of the monitor
and the stand body. You can hurt your finger(s).
Theft prevention locking device
Locking Device
Use this locking cable
separately if required.
) to prevent theft.
3
(This has to be purchased
POWER
TV/PC
INPUT
CH
CH
ENTER
MTS
MUTE
FCR
MENU
REVIEW
MEMORY/ERASE
CAPTION
A.PROG
SLEEP
APC
DASP
ARC/
VOL
VOL
*
Name and Function of the Parts
Name of the Remote Control Buttons
TV/PC :
Not working
TV/PC button
POWER
INPUT
Input
AV
Component
RGB
DVI
HDMI
MENU
Each time you press the Input button it will
change to
AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the
screen will automatically move to the selected
menu.
MTS
Not working
A.PROG
PC: Automatic adjustment function (Operational for the analog signal only)
MEMORY/ERASE
Not working
CAPTION
Select a closed caption
(AV only)
Number buttons
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
AAA Type
4
Name and Function of the Parts
Name of the Remote Control Buttons
MUTE
Switches the sound on or off.
FCR
Not working
.
MUTE
VOL
MENU
APC
CH
ENTER
CH
REVIEW
DASP
FCR
VOL
SLEEP
ARC/
CH ( ) Buttons
Up and Down Button.
VOL ( ) Buttons
Volume Button
ENTER Button
Use when functional adjustment is completed.
MENU
Use this button to enter the On Screen Display menu.
*
REVIEW
Not working
SLEEP : SLEEP Timer
You can set a time period after which the all modes should switch
itself to standby.
Press the key repeatedly to select the number of minutes.
_ _ _ (off)
240 180
APC Button
Press repeatedly to select Clear, Optimum, Soft, User picture mode.
(Auto Picture Control)
10
20 30
120
60
90
DASP Button
(Digital Auto Sound Processing)
Use this button to select the sound tone.
Press repeatedly to select Flat, Music, Movie, Sports, User
ARC/
*
To select the image size of the screen.
•
When AV mode: 16:9, Horizon, Zoom1,Zoom2, 4:3
• When RGB/DVI/HDMI/Component mode
5
: 16:9, 4:3
sound tone.
Name and Function of the Parts
Ext. IN
AC IN
AUDIO IN
(RGB/DVI)
VIDEO
COMPONENT
IN
AUDIO
Y
P
B
P
R
AUDIO
L
R
L
VIDEO
R
RGB IN (PC)
DVI-D
HDMI
S-VIDEO
Rear View
COMPONENT
IN
Y
S-VIDEO
B
VIDEO
R
Ext. IN
VIDEO
AUDIO
L
AUDIO
R
AUDIO IN
(RGB/DVI)
RGB IN (PC)
DVI-D
HDMI
P
P
L
R
Power Connector : Connect the power cord.
HDMI Digital Signal Connector
DVI Digital Signal Connector
D-Sub Analog Signal Connector
RGB, DVI Sound Jack : Connect to the jack in the PC sound card or D-TV sound Output Jack.
AV Input Terminal
Component Input Terminal
Ext In Jack : Connect the TN300 Tuner. (Please refer to TN300 install guide.)
6
AUDIO
L
VIDEO
R
S-VIDEO
(MONO)
Name and Function of the Parts
AV Input Terminal
S-Video Input Terminal
Video Input Terminal
Audio Input Terminal
7
Connecting to External Devices
RGB IN (PC)
Ext. IN
AC IN
AUDIO IN
(RGB/DVI)
VIDEO
COMPONENT
IN
AUDIO
Y
P
B
P
R
AUDIO
L
R
L
VIDEO
R
RGB IN (PC)
DVI-D
HDMI
S-VIDEO
Connecting to your PC
First of all, see if the computer, product and the peripherals are turned off.
1.
Then, connect the signal input cable.
Rear side of the product.
Connecting with the D-Sub signal input cable.
A
Rear side of the product
Connecting with the DVI signal input cable.
B
DVI-D
.
Macintosh Adapter (Not included)
Use the standard Macintosh adapter since an
incompatible adapter is available in the market.
(Different signaling system)
Rear side of the product.
Connect the audio cable.
2.
Audio cable
AUDIO IN
(RGB/DVI)
Rear side of the product.
•
Make sure to check the sound card connection terminal in the PC before connecting to the product.
If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumper
or the PC application. (For more details, refer to the sound card user’s guide.)
- Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.
- *Line Out : The terminal connected to the speaker equipped with an amplifier.
If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This product is integrated
with an amplifier.
8
8
Connect the power cord.
Ext. IN
AC IN
AUDIO IN
(RGB/DVI)
VIDEO
COMPONENT
IN
AUDIO
Y
P
B
PR
AUDIO
L
R
L
VIDEO
R
RGB IN (PC)
DVI-D
HDMI
S-VIDEO
3.
Turn on power by pressing the power button on the product.
1
4.
Turn on the PC.
2
Connecting to External Devices
Rear side of the product.
Power button
Select an input signal.
5.
Press the INPUT button on the remote control to select the input signal.
Or, press the INPUT button at the top side of the product.
INPUT ENTER
•
Select RGB
A
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
Note
Input
B
•
Select DVI
AV
Component
RGB
DVI
HDMI
MENU
• Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.
9
Input
AV
Component
RGB
DVI
HDMI
MENU
Connecting to External Devices
VIDEO
OUT
AUDIO
OUT
AUDIO
L
VIDEO
R
S-VIDEO
(MONO)
VIDEO
OUT
AUDIO
OUT
AUDIO
L
VIDEO
R
S-VIDEO
(MONO)
Connecting to VCR/DVD
Connect the video/audio cable as shown in the figure below and then connect the power cord (See page 9).
1.
When using the S-Video cable.
When using the RCA cable.
A
•
Connect the input terminal with a
proper colour match.
B
•
Connect to the S-Video input terminal to
watch high image quality movies.
Rear side of
the Product
RCA Cable
(Not included)
VCR/DVD
Select an input signal.
2.
Press the INPUT button on the remote control to select the input signal.
Or, press the INPUT button at the top side of the product.
INPUT ENTER
When connecting with a RCA cable.
A
•
Select AV
B
When connecting with a S-Video cable.
Select AV
•
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
Rear side of
the Product
RCA Cable
(Not included)
VCR/DVD
S-Video Cable
(Not included)
Input
AV
Component
RGB
DVI
HDMI
MENU
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
Note
• In case the RCA cable is connected simultaneously as S-Video cable is connected, S-Video
cable is first.
10
Connecting to External Devices
Connecting to Set-top Box /DVD (480i/576i/480p/576p/720p/1080i)
Connect the video/audio cable as shown in the figure below and then connect the power
1.
cord (See page 9).
•
Connect the input terminal with a proper color match.
Rear side of the Product
COMPONENT
Y
R
L
AUDIO
P
P
R
B
IN
VIDEO
Audio Cable
(Not included)
Component Cable
(Not included)
Set-top Box /DVD
Select an input signal.
2.
Press the INPUT button on the remote control to select the input signal.
Or, press the INPUT button at the top side of the product.
INPUT ENTER
•
Select Component
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
Input
AV
Component
RGB
DVI
HDMI
MENU
11
Connecting to External Devices
When watching HDMI from the DVD/Set-top Box
Connect the HDMI cable as shown in the figure below and then connect the power cord (See page 9).
1.
Rear side of the Product
HDMI cable
(not included)
[Set-top Box/DVD]
Select an input signal.
2.
Press the INPUT button on the remote control to select the input signal.
Or, press the INPUT button at the top side of the product.
INPUT ENTER
•
Select HDMI
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
12
Input
AV
Component
RGB
DVI
HDMI
MENU
Connecting to External Devices
RGB IN (PC)
AUDIO IN
(RGB/DVI)
AUDIO IN
(RGB/DVI)
DVI-D
When watching RGB/DVI from the
Connect the D-sub cable, RCA/PC cable as shown in the below figure
1.
Set-top Box /DVD
and then connect the power cord. (see page 9)
A
[Rear side of the Product]
D-Sub cable
RCA-Stereo
(not included)
cable
B
[Rear side of the Product]
DVI cable
RCA-Stereo
(not included)
cable
[Set-top Box/DVD]
Select an input signal.
2.
[Set-top Box/DVD]
Press the INPUT button on the remote control to select the input signal.
Or, press the INPUT button at the top side of the product.
INPUT ENTER
•
Select RGB
A
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
Input
AV
Component
RGB
DVI
HDMI
MENU
13
B
•
Select DVI
Input
AV
Component
RGB
DVI
HDMI
MENU
Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
INPUT
MENU
VOLENTER
Power Indicator
Power Button
MENU Button
OSD Select/Adjust Button
• This Indicator lights up blue when the display operates normally
(On Mode). If the display is in Sleep (Energy Saving) Mode, this
indicator colour changes to amber.
• Use this button to turn the product on and off.
• Use this button to show/hide the OSD (On Screen Display) menu
screen.
•
Use
this
button to select an icon or adjust the setting in the OSD screen.
•
Use
this
button to select an icon or adjust the setting in the OSD
screen.
• Adjust the volume.
15
Volume
30
Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
ENTER Button
INPUT Button
Each time you press the Input button it will change to AV Component RGB DVI
HDMI.
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
• ENTER button is usually used in choosing the MENU.
When there is no MENU on the screen pushing the ENTER button
will give the information about the current input source.
Input
AV CVBS, S-Video
Component HDTV, DVD
RGB D-Sub analog signal
DVI DVI Digital signal
HDMI HDMI Digital signal
AV
Component
RGB
DVI
HDMI
MENU
16
Adjusting the Screen
OSD (On Screen Display) Menu
Icon Function Description
Adjusting the picture function.
Picture
Adjusting the sound function.
Sound
Adjusting the time function.
Timer
Selecting the special function.
Special
Screen
Adjusting the screen function.
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides graphical
presentation.
17
Adjusting the Screen
PICTURE ID adjust the picture function
(RGB-PC/DVI-PC)
APC (Auto Picture Control)
Picture
APC
ACC
XD
Cinema
Reset
MENU
User
Contrast 100
Brightness 100
MENU
ACC (Auto Color Control)
Picture
APC
ACC
XD
Cinema
Reset
MENU
<
Clear
Optimum
Soft
User
9300K
<
6500K
sRGB
User
The APC function automatically adjusts the screen
image quality.
• Clear
Select this option to display with a sharp image.
• Optimum
The most general and natural screen display
status.
• Soft
Select this option to display with a mild image.
• User
Select this option to use the user-defined settings.
Contrast : To adjust the contrast of the screen.
Brightness : To adjust the brightness of the screen.
The ACC function automatically adjusts the screen
colour set.
• 9300K
Slightly purplish white.
• 6500K
Slightly bluish white.
• sRGB
Slightly lower brightness.
• User
Select this option to use the user-defined settings.
User
Red 0
Green 0
Blue 0
MENU
Red / Green / Blue
Set your own colour levels.
19
Adjusting the Screen
PICTURE ID adjust the picture function
(RGB-PC/DVI-PC)
XD
Cinema
Reset
XD is LG Electronics unique picture improving technology to display a real HD source through an
advanced digital signal processing algorithm.
It's not available to use this function in RGB-PC or DVI-PC modes.
Manual is activated after selecting the user of APC.
(It's not working RGB-PC, DVI-PC mode.)
(
Function works in the following mode - AV, Component 480i/576i)
When you watch the movie, this function adjusts the set to the best picture appearance.
(It's not working RGB/DVI mode.)
Return to the default settings APC, ACC at the factory.
20
Adjusting the Screen
PICTURE ID adjust the picture function
APC (Auto Picture Control)
Picture
APC
ACC
XD
Cinema
Reset
MENU
User
Contrast 100
Brightness 50
Color 60
Sharpness 50
Tint 0
MENU
ACC (Auto Color Control)
Picture
APC
ACC
XD
Cinema
Reset
MENU
<
Clear
Optimum
Soft
User
<
Cool
Normal
Warm
User
(AV/Component/RGB-DTV/DVI-DTV/HDMI-DTV)
The APC function automatically adjusts the screen
image quality.
• Clear
Select this option to display with a sharp image.
• Optimum
The most general and natural screen display
status.
• Soft
Select this option to display with a mild image.
• User
Select this option to use the user-defined settings.
Contrast : To adjust the contrast of the screen.
Brightness : To adjust the brightness of the screen.
Color : To adjust the colour to desired level.
Sharpness : To adjust the clearness of the screen.
Tint : To adjust the tint to desired level.
The ACC function automatically adjusts the screen
color set.
• Cool
Slightly purplish white.
• Normal
Slightly bluish white.
• Warm
Slightly reddish white.
• User
Select this option to use the user-defined settings.
User
Red 0
Green 0
Blue 0
MENU
Red / Green / Blue
Set your own colour levels.
21
Adjusting the Screen
XD
Picture
APC
ACC
XD
Cinema
Reset
Cinema
Reset
PICTURE ID adjust the picture function
<
Auto
Manual
MENU
(
Function works in the following mode - AV, Component 480i)
When you watch the movie, this function adjusts the set to the best picture appearance.
Return to the default settings APC, ACC, XD, Cinema at the factory.
(AV/Component/RGB-DTV/DVI-DTV/HDMI-DTV)
XD is LG Electronics unique picture improving
technology to display a real HD source through an
advanced digital signal processing algorithm.
Manual is activated after selecting the user of APC.
22
Troubleshooting
No image is displayed
● Is the product's power cord
connected?
● Is the power indicator turning on?
● Power is on, power indicator is blue
but the screen appears extremely
dark.
● Does the power indicator look amber?
● Does the 'Out of range' message
appear?
● Does the 'Check signal cable'
message appear?
• Check if the power cord is properly connected to
the outlet.
• See if the power switch is turned on.
• Adjust brightness and contrast again.
• If the product is in power saving mode, move the
mouse or press any key.
• In DVD Player or Set-top Box, check the power
status of connected device.
• The signal from the PC (video card) is out of the
vertical or horizontal frequency range of the
product. Adjust the frequency range by referring to
the Specifications in this user's guide.
* Maximum resolution
M1994A : RGB : 1440 X 900 @75 Hz
DVI : 1440 X 900 @60 Hz
M2294A : 1680 X 1050 @60 Hz
• The signal cable between PC and product is not
connected. Check the signal cable.
• Press the 'INPUT' button in the remote control to
check the input signal.
'Unknown Product' message appears when the product is connected.
●
Did you install the driver?
Note
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times
every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When the 1 is divided by
horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal
frequency. The unit is kHz.
• Install the product driver, which is provided with
the product, or download it from the web site.
(http://www.lge.com)
• See if the plug&play function is supported by
referring to the video card user's guide.
27
Specifications
The product specifications can change without prior notice for product improvement.
M1994A
LCD Panel
Video Signal
Input Connector
Power
Tilt
Screen Type
Pixel Pitch 0.2835 mm
Max. Resolution RGB : 1440 X 900 @75 Hz
Recommended Resolution
Horizontal Frequency 28 - 83 kHz
Vertical Frequency 56 - 75 Hz
Synchronization Type Separate Sync, Digital
Rated Voltage AC 100-240V~ 50/60Hz 0.8A
Power Consumption On Mode : 50 W (Typ.)
Tilt Range -5˚ ~ 15˚
19 inches Wide (48.133 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 48.133 cm
DVI : 1440 X 900 @60 Hz
1440 X 900 @60 Hz
S-Video, Composite video, D-Sub Analog, DVI-D,
HDMI, PC Audio In, Headphone/Earphone, component
Sleep Mode ≤ 1 W (RGB)
Off Mode ≤ 1 W
Dimension/Weight
Environmental Conditions
Size (WxDxH) 456.2 mm x 193.2 mm x 394.7 mm
Weight (excl. package) 4.06 kg (8.93 Ibs)
Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 20% ~ 80%
Storage Condition Temperature: -10˚C ~ 60˚C , Humidity: 5% ~ 90%
30
Specifications
The product specifications can change without prior notice for product improvement.
M2294A
LCD Panel
Video Signal
Input Connector
Power
Tilt
Screen Type
Pixel Pitch 0.282 mm
Max. Resolution RGB : 1680 X1050 @60 Hz
Recommended Resolution
Horizontal Frequency 28 - 83 kHz
Vertical Frequency 56 - 75 Hz
Synchronization Type Separate Sync, Digital
Rated Voltage AC 100-240V~ 50/60Hz 0.9A
Power Consumption On Mode : 50 W (Typ.)
Tilt Range -5˚ ~ 15˚
22 inches Wide (55.867 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size:
DVI : 1680 X1050 @60 Hz
1680 X1050 @60 Hz
S-Video, Composite video, D-Sub Analog, DVI-D,
HDMI, PC Audio In, Headphone/Earphone, component
Sleep Mode ≤ 1 W (RGB)
Off Mode ≤ 1 W
55.867
cm
Dimension/Weight
Environmental Conditions
Size (WxLxH) 521.7 mm x 193.2 mm x 435.4 mm
Weight (excl. package) 4.9 kg (10.78 Ibs)
Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 20% ~ 80%
Storage Condition Temperature: -10˚C ~ 60˚C , Humidity: 5% ~ 90%
31
PC Mode – Preset Mode
It's not support in HDMI-PC mode.
M1994A
Horizontal
Preset mode
1
720 x 400
2
640 x 480
3
640 x 480
4
800 x 600
5
800 x 600
6
1024 x 768
7
1024 x 768
8
1152 x 864
9
1280 x 1024
10
1280 x 1024
* 1~13 : RGB mode * 1~12 : DVI mode
M2294A
Preset mode
1
720 x 400
2
640 x 480
3
640 x 480
4
800 x 600
5
800 x 600
6
1024 x 768
7
1024 x 768
8
1152 x 864
9
1280 x 1024
10
1280 x 1024
Frequency
(kHz)
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
Horizontal
Frequency
(kHz)
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
Specifications
Vertical
Frequency
(Hz)
70
60
75
60
75
60
75
75
60
75
Vertical
Frequency
(Hz)
70
60
75
60
75
60
75
75
60
75
Preset mode
11
1440 x 900
12
1440 x 900
13
1440 x 900
Preset mode
11121680 x 1050
1680 x 1050
Horizontal
Frequency
(kHz)
55.5
55.935
70.635
Horizontal
Frequency
(kHz)
64.674
65.290
Vertical
Frequency
(Hz)
60
60
75
Vertical
Frequency
(Hz)
60
60
DTV -Timing
Horizontal
Preset mode
*1
720 x 480/60p
*2
720 x 480/60p
3
720 x 576/50p
*4
1280 x 720/50p
*5
1280 x 720/60p
*6
1280 x 720/60p
7
1920 x 1080/60i
8
1920 x 1080/60i
9
1920 x 1080/50i
* : User have to select directness PC or DTV
when using the PC or the Set-top box this resolution.
Frequency
(kHz)
31.47
31.5
31.25
37.5
44.96
45
33.72
33.75
28.125
Vertical
Frequency
(Hz)
60
60
50
50
60
60
60
60
50
32
Power Indicator
Mode
On Mode
Sleep Mode
Off Mode
Product
Blue
Amber
Off
Regulatory Information cont.
FCC Compliance Statement
This equipment has been tested and found to comply
within the limits of a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio
or television reception (which can be determined by
turning the equipment on and off), the user is encouraged
to try to correct the interference by using one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's (or your) authority to operate the equipment. Only
peripherals (digital input/output devices, terminals, printers,
etc.) certified to comply with the Class B limits may be
attached to this monitor. Operation with non-certified
peripherals is likely to result in interference to radio and TV
reception. Only shielded signal cables may be used with
this System.
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
CE Conformity Notice
Products with the “CE” Marking comply with the EMC
Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compiance with these directives implies conformity to the
following European Norms :
• EN 55022 ; Radio Frequency Interference
• EN 55024 ; Electromagnetic Immunity
• EN 61000-3-2 ; Power Line Harmonics
• EN 61000-3-3 ; Voltage Fluctuations
• EN 60950-1 ; Product Safety
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
NOTICE
(for Europe)
NOTICE
Low Radiation Compliance (MPR II)
This monitor meets one of the strictest guidelines available
today for low radiation emissions, offering the user extra
shielding and an antistatic screen coating. These
guidelines, set forth by a government agency in Sweden,
limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF)
electromagnetic range.
TCO'99
(TCO'99 applied model only)
Canadian DOC Notice
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations. Cet appareil numérique de la classe B
01
Congratulations!
You have just purchased a TCO’99 approved and labelled
product! Your choice has provided you with a product
developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and
also to the further development of environmentally
adapted electronics products.
Regulatory Information cont.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an
established method for encouraging the adaptation of
goods and services to the environment. With the growing
manufacture and usage of electronic equipment
throughout the world, there is a recognized concern for the
materials and substances used by electronic products
with regards to their eventual recycling and disposal. By
proper selection of these materials and substances, the
impact on the environment can be minimized.
There are also other characteristics of a computer, such as
energy consumption levels, that are important from the
viewpoints of both the work (internal) and natural (external)
environments. Electronic equipment in offices is often left
running continuously, resulting in unnecessary
consumption of large amounts of energy and additional
power generation. From the standpoint of carbon dioxide
emissions alone, it is vital to save energy.
What does labelling involve?
The product meets the requirements for the TCO’99
scheme which provides for international and environmental
labelling of personal computers and/or displays.
The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and
Statens Energimyndighet (The Swedish National
Energy Administration).
Approval requirements cover a wide range of issues:
ecology, ergonomics, emission of electrical and magnetical
fields, energy consumption and electrical safety.
Ecological criteria impose restrictions on the presence and
use of heavy metals, brominated and chlorinated flame
retardants, and other substances. The product must be
prepared for recycling and the manufacturing site(s) shall
be certified according to ISO14001 or EMAS registered.
Energy requirements include a demand that the system
unit and/or display, after a certain period of inactivity,
shall reduce its power consumption to a lower level in one
or more stages. The length of time to reactivate the system
unit shall be reasonable for the user.
Labelled products must meet strict environmental
demands, for example, in respect of the reduction of
electrical and magnetical fields as well as work load and
visual ergonomics.
Below you will find a brief summary of the ecological
requirements met by this product. The complete
ecological criteria document can be found at TCO
Development’s website http://www.tcodevelopment.com
or may be ordered from:
TCO Development
SE-114 94 STOCKHOLM, Sweden
Fax: +46 8 782 92 07
Email : development@tco.se
Information regarding TCO’99 approved and labelled
products may also be obtained at
http://www.tcodevelopment.com
Ecological requirements
Flame retardants
Flame retardants may be present in printed wiring board
laminates, cables, and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30%
by weight of the plastic in a computer casing can consist of
flame retardant substances. Many flame retardants
contain bromine or chlorine, and these flame retardants
are chemically related to PCBs (polychlorinated
biphenyls). Both the flame retardants containing bromine
or chlorine and the PCBs are suspected of giving rise to
health effects, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative*
processes when not disposed of in accordance with strict
standards for disposal.
TCO’99 requires that plastic components weighing more
than 25 grams shall not contain flame retardants with
organically bound bromine or chlorine. Flame retardants
are allowed in the printed wiring board laminates due to
the lack of commercially available alternatives.
Cadmium**
Cadmium is present in rechargeable batteries and in the
colour-generating layers of certain computer displays.
TCO’99 requires that batteries, the colour-generating
layers of display screens, and the electrical or electronics
components shall not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and
switches. TCO’99 requires that batteries shall not contain
any mercury. It also demands that mercury is not present
in any of the electrical or electronics components
associated with the labelled unit. There is however one
02
Regulatory Information cont.
exception. Mercury is, for the time being, permitted in the
back light system of flat panel monitors as there today is
no commercially available alternative. TCO aims on
removing this exception when a mercury free alternative is
available.
Lead**
Lead can be found in picture tubes, display screens,
solders and capacitors. TCO’99 permits the use of lead
due to the lack of commercially available alternatives, but
in future requirements TCO Development aims at
restricting the use of lead.
_____________________________________________
* Bio-accumulative is defined as substances which
accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals
which are bio-accumulative.
TCO’03
Congratulations!
The display you have just purchased carries the TCO’03
Displays label.
This means that your display is designed,manufactured
and tested according to some of the strictest quality and
environmental requirements in the world. This makes for a
high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
• Good visual ergonomics and image quality in order to
improve the working environment for the user and to
reduce sight and strain problems. Important
parameters are luminance, contrast, resolution,
reflectance, colour rendition and image stability.
Energy
• Energy-saving mode after a certain time – beneficial
both for the user and the environment
• Electrical safety
Emissions
• Electromagnetic fields
(TCO’03 applied model only)
• Noise emissions
Ecology
• The product must be prepared for recycling and the
manufacturer must have a certified environmental
management system such as EMAS or ISO 14 001
• Restrictions on
chlorinated and brominated flame retardants and
polymers
heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been
developed by TCO Development in co-operation with
scientists, experts, users as well as manufacturers all over
the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in
a more user-friendly direction. Our labelling system started
with displays in 1992 and is now requested by users and
IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
English
Information for Environmental Preservation
LGE. announced the 'LG Declaration for a Cleaner
Environment' in 1994, and this ideal has served as a
guiding managerial principle ever since. The Declaration is
a foundation that has allowed us to undertake
environmentally friendly activities in careful consideration
of economic, environmental, and social aspects.
We promote activities for environmental preservation, and
we specifically develop our products to embrace the
concept of environment-friendly.
We minimize the hazardous materials contained in our
products. For example, there is no cadmium to be found in
our monitors.
Information for recycling
This monitor may contain parts which could be hazardous
to the environment. It is important that this monitor be
recycled after use.
LGE. handles all waste monitors through an
environmentally acceptable recycling method. There are
several take-back and recycling systems currently in
03
Regulatory Information cont.
operation worldwide. Many parts will be reused and
recycled, while harmful substances and heavy metals are
treated by an environmentally friendly method.
If you want to find out more information about our
recycling program, please contact your local LG vendor or
a corporate representative of LG.
We set our vision and policies on a cleaner world by
selecting the issue of the global environment as a task for
corporate improvement. Please visit our website for more
information about our ‘green’ policies.
http://www.lge.com/about/environment/html/Recycling.jsp
Deutsch
Informationen zur Erhaltung der Umwelt
Im Jahr 1994 verkündete LGE die 'LG Declaration for a
Cleaner Environment' (LG Erklärung für eine sauberere
Umwelt). Seitdem dient dieses Ideal als führendes Prinzip
des Unternehmens. Diese Erklärung war die Basis für die
Durchführung von
umweltfreundlichen Aktivitäten, wobei wirtschaftliche,
umweltbezogene und soziale Aspekte in die
Überlegungen mit einbezogen wurden.
Wir fördern Aktivitäten zum Schutz der Umwelt und die
Entwicklung unserer Produkte ist darauf ausgerichtet,
unserem Konzept bezüglich Umweltfreundlichkeit gerecht
zu werden.
Wir sind darauf bedacht, den Anteil der in unseren
Produkten enthaltenen schädlichen Materialien zu
minimieren. So ist in unseren Monitoren beispielsweise
kein Kadmium zu finden.
Informationen zum Thema Recycling
Dieser Monitor enthält Teile, die umweltschädlich sein
können. Es ist unbedingt erforderlich, dass der Monitor
recycelt wird, nachdem er außer Dienst gestellt wurde.
Bei LGE. werden alle ausrangierten Monitore in einem
unter umweltbezogenen Aspekten geeigneten Verfahren
recycelt. Augenblicklich sind weltweit mehrere
Rücknahme- und Recyclingsysteme im Einsatz. Viele
Teile werden wieder verwendet und recycelt. Schädliche
Substanzen und Schwermetalle werden durch
umweltverträgliche Verfahren behandelt.
Falls Sie mehr über unser Recyclingprogramm erfahren
möchten, wenden Sie sich bitte an Ihren lokalen LGHändler oder einen Unternehmensvertreter von LG.
Wir richten unsere Firmenpolitik auf eine sauberere
Umwelt hin aus, indem wir umweltspezifische Aspekte als
wichtigen Punkt in die Weiterentwicklung unseres
Unternehmens einfließen lassen. Zusätzliche
Informationen über unsere ‘grüne’ Firmenpolitik erhalten
Sie auf unserer Website.
http://www.lge.com/about/environment/html/Recycling.jsp
Français
Information sur la protection del’environnement
LGE. a publié sa 'Déclaration en faveur d’un
environnement plus propre' en 1994 et celle-ci est restée,
depuis lors, un principe directeur de notre entreprise.
Cette déclaration a servi de base à notre réflexion et nous
a permis de prendre en compte à la fois les aspects
économiques et sociaux de nos activités, tout en
respectant l’environnement.
Nous encourageons les activités en faveur de la
préservation de l’environnement et c’est dans cet esprit
que nous développons nos produits : nous réduisons au
minimum les matières dangereuses qui entrent dans leur
composition et l’on ne trouve pas de cadmium, par
exemple, dans nos moniteurs.
Information sur le recyclage
Ce moniteur peut contenir des composants qui présentent
un risque pour l’environnement. Il est donc important que
celui-ci soit recyclé après usage.
LGE. traite les moniteurs en fin de cycle conformément à
une méthode de recyclage respectueuse de
l’environnement. Nous reprenons nos produits et les
recyclons dans plusieurs sites répartis dans le monde
entier. De nombreux composants sont réutilisés et
recyclés, et les matières dangereuses, ainsi que les
métaux lourds, sont traités selon un procédé écologique.
Si vous souhaitez plus de renseignements sur notre
programme de recyclage, veuillez contacter votre
revendeur LG ou un l’un de nos représentants.
Nous voulons agir pour un monde plus propre et croyons
au rôle de notre entreprise dans l’amélioration de
l’environnement. Pour plus de renseignements sur notre
politique “verte”, rendez visite à notre site :
http://www.lge.com/about/environment/html/Recycling.jsp
04
Regulatory Information cont.
Italiano
Informazioni per la tutela dell’ambiente
La LGE. ha annunciato nel 1994 la cosiddetta 'LG
Declaration for a Cleaner Environment' (Dichiarazione di
LG a favore di un ambiente più pulito), un ideale che da
allora funge da principio ispiratore della gestione
aziendale. La dichiarazione rappresenta il fondamento che
consente di intraprendere attività a favore dell'ambiente
tenendo conto degli aspetti economici, ambientali e
sociali.Noi della LG, promuoviamo attività a favore della
tutela dell'ambiente sviluppando appositamente i nostri
prodotti per cogliere il concetto del rispetto dell’ambiente
riducendo i materiali dannosi presenti nei nostri prodotti.
Ad esempio nei nostri monitor non è presente il cadmio.
Informazioni per il riciclaggio
Il monitor può presentare componenti che potrebbero
risultare eventualmente dannosi per l'ambiente. È
importante che il monitor sia riciclato al termine del suo
utilizzo.
La LGE. gestisce tutti i monitor di rifiuto con un metodo di
riciclaggio soddisfacente dal punto di vista ambientale. In
tutto il mondo sono attualmente in funzione numerosi
sistemi di riciclaggio e recupero. I diversi componenti sono
riutilizzati e riciclati, mentre le sostanze dannose e i metalli
pesanti vengono trattati con un metodo rispettoso
dell’ambiente.
Se si desiderano maggiori informazioni in merito al
programma di riciclaggio, è consigliabile rivolgersi al
proprio rivenditore LG o ad un rappresentante aziendale
della LG.
Noi della LG impostiamo la nostra visione e le nostre
politiche a favore di un mondo più pulito ponendo la
questione dell'ambiente dal punto di vista globale come
una mansione rivolta al miglioramento della nostra
azienda. Vi invitiamo a visitare il nostro sito internet per
ulteriori informazioni sulla nostra politica “verde”.
http://www.lge.com/about/environment/html/Recycling.jsp
Espanõl
Información para la conservación
medioambiental
LGE. presentó la 'Declaración para un entorno más limpio
de LG' en 1994 y este ideal ha servido para guiar nuestros
principios empresariales desde entonces. La Declaración
es la base que nos ha permitido llevar a cabo tareas que
respetan el medio ambiente siempre teniendo en cuenta
aspectos sociales,
económicos y medioambientales.
Promocionamos actividades orientadas a la conservación
del medio ambiente y desarrollamos nuestros productos
específicamente para que se ajusten a la filosofía que
protege el entorno.
Reducimos al máximo el uso de materiales de riesgo en
nuestros productos. Un ejemplo de ello es la ausencia
total de cadmio en nuestros monitores.
Información para el reciclaje
Este monitor puede contener piezas que entrañen riesgos
medioambientales. Es importante reciclar este monitor
después de su utilización.
LGE. trata todos los monitores usados siguiendo un
método de reciclaje que no daña al entorno. Contamos
con diversos sistemas de recuperación y reciclaje que
funcionan a nivel mundial en la actualidad. Es posible
reciclar y reutilizar muchas de las piezas, mientras que las
sustancias dañinas y los metales pesados se tratan
siguiendo un método que no perjudique al medio
ambiente. Si desea obtener más información acerca del
programa de reciclaje, póngase en contacto con su
proveedor local de LG o con un representante empresarial
de nuestra marca.
Basamos nuestra visión y nuestras políticas en un mundo
más limpio y para ellos optamos por un entorno global
como tarea principal de nuestra evolución como empresa.
Visite nuestra página Web para obtener más información
sobre nuestras políticas ecológicas.
http://www.lge.com/about/environment/html/Recycling.jsp
Português
Informações relacionadas à preservação
ambiental
A LGE. anunciou a 'LG Declaration for a Cleaner
Environment' (Declaração da LG para um ambiente mais
limpo) em 1994 e esse ideal tem servido desde então
como um princípio administrativo de orientação. A
Declaração é a base que nos tem permitido realizar
atividades favoráveis ao ambiente com consideração
atenta aos aspectos econômicos, ambientais e sociais.
Promovemos atividades de preservação ambiental e
desenvolvemos nossos produtos para englobar
05
Regulatory Information cont.
especificamente o conceito de favorável ao ambiente.
Reduzimos os materiais perigosos contidos em nossos
produtos. Por exemplo, não há cádmio em nossos
monitores.
Informações relacionadas à reciclagem
Este monitor pode conter peças que podem representar
riscos ao ambiente. É importante que ele seja reciclado
após o uso.
A LGE. cuida de todos os monitores descartados através
de um método de reciclagem agradável ao ambiente. Há
vários sistemas de devolução e reciclagem atualmente
em operação no mundo. Muitas peças serão reutilizadas
e recicladas e as substâncias nocivas e os metais
pesados passarão por tratamento através de um método
favorável ao ambiente.
Para obter mais informações sobre nosso programa de
reciclagem, entre em contato com seu fornecedor LG
local ou com um representante corporativo da LG.
Definimos nossa visão e nossas políticas relacionadas a
um mundo mais limpo selecionando a questão do
ambiente global como uma tarefa de aprimoramento
corporativo. Visite nosso site para obter mais informações
sobre nossas políticas de meio ambiente.
http://www.lge.com/about/environment/html/Recycling.jsp
Informatie met betrekking tot recycling
Deze monitor bevat materialen die schadelijk zouden
kunnen zijn voor het milieu. Het is belangrijk dat deze
monitor aan het einde van zijn levensduur wordt
gerecycled.
LGE. verwerkt alle afvalmonitors via een milieuvriendelijke
recyclingmethode. Hiervoor worden er momenteel
wereldwijd verscheidene inname- en recyclingsystemen
gehanteerd. Een groot aantal onderdelen wordt opnieuw
gebruikt en gerecycled, waarbij schadelijke stoffen en
zware metalen volgens een milieuvriendelijke methode
worden verwerkt.
Voor meer informatie over ons recyclingprogramma kunt u
contact opnemen met uw plaatselijke LGvertegenwoordiger of een LG-vestiging.
Onze visie en ons beleid met betrekking tot een schonere
wereld vloeien voort uit het feit dat wij het milieu hebben
aangemerkt als een onderwerp dat speciale aandacht
verdient binnen onze onderneming. Bezoek onze website
voor meer informatie over ons 'groene' beleid.
http://www.lge.com/about/environment/html/Recycling.jsp
Russian
Nederlands
Informatie met betrekking tot het behoud van
het milieu
LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner
Environment' (de LG-verklaring met betrekking tot een
schoner milieu). Deze verklaring en het ideaal van een
schoner milieu fungeren sindsdien als een bestuurlijke
leidraad voor onze onderneming. Op basis van deze
verklaring ontplooien wij milieuvriendelijke activiteiten,
waarbij er zowel met sociale en economische aspecten,
als met milieuaspecten zorgvuldig rekening wordt
gehouden.
Wij ondersteunen activiteiten die zijn gericht op het
behoud van het milieu en wij houden bij het ontwikkelen
onze producten specifiek rekening met de
milieuvriendelijkheid van onze producten.
Wij minimaliseren het gebruik van schadelijke stoffen in
onze producten. Er wordt bijvoorbeeld geen cadmium
verwerkt in onze monitors.
06
»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚
¬ 1994 „У‰Ы НУФУ‡ˆЛˇ LGE УФЫ·ОЛНУ‚‡О‡
'ƒВНО‡‡ˆЛ˛ LG ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚',
НУЪУ‡ˇ Т ЪВı ФУ ТОЫКЛЪ УТМУ‚М˚П ФЛМˆЛФУП
ЫФ‡‚ОВМЛˇ. Х‡ УТМУ‚В ˝ЪУИ ‰ВНО‡‡ˆЛЛ П˚ ТПУ„ОЛ
ФВ‰ФЛМˇЪ¸ ‰ВИТЪ‚Лˇ, У·ВТФВ˜Л‚‡˛˘ЛВ
·ВБУФ‡ТМУТЪ¸ УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ ФЛ ˝ЪУП
‰УОКМУВ ‚МЛП‡МЛВ ˝НУМУПЛ˜ВТНЛП, ˝НУОУ„Л˜ВТНЛП Л
ТУˆЛ‡О¸М˚П ‡ТФВНЪ‡П.
Г˚ ТЪЛПЫОЛЫВП ‰ВˇЪВО¸МУТЪ¸ ФУ Уı‡МВ
УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ УТУ·УВ ‚МЛП‡МЛВ
‡Б‡·УЪНВ М‡¯ВИ ФУ‰ЫНˆЛЛ ‚ ТУУЪ‚ВЪТЪ‚ЛЛ Т
НУМˆВФˆЛВИ ˝НУОУ„Л˜ВТНУИ ·ВБУФ‡ТМУТЪЛ.
Г˚ Т‚У‰ЛП Н ПЛМЛПЫПЫ ТУ‰ВК‡МЛВ УФ‡ТМ˚ı
‚В˘ВТЪ‚ ‚ М‡¯ВИ ФУ‰ЫНˆЛЛ. Х‡ФЛПВ, ‚ М‡¯Лı
ПУМЛЪУ‡ı ‚˚ МВ М‡И‰ВЪВ Н‡‰ПЛˇ.
»МЩУП‡ˆЛˇ ФУ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚
›ЪУЪ ПУМЛЪУ ПУКВЪ ТУ‰ВК‡Ъ¸ НУПФУМВМЪ˚,
НУЪУ˚В ПУ„ЫЪ М‡МВТЪЛ Ы˘В· УНЫК‡˛˘ВИ ТВ‰В.
Regulatory Information cont.
ХВУ·ıУ‰ЛПУ ЫЪЛОЛБЛУ‚‡Ъ¸ ПУМЛЪУ ФУТОВ
ЛТФУО¸БУ‚‡МЛˇ.
KУФУ‡ˆЛˇ LGE ФВВ‡·‡Ъ˚‚‡ВЪ ‚ТВ ·‡НУ‚‡ММ˚В
ПУМЛЪУ˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ ФЛВПОВПУ„У
ПВЪУ‰‡ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚. œУ ‚ТВПЫ ПЛЫ
‰ВИТЪ‚Ы˛Ъ ТЛТЪВП˚ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ Л ‚УБ‚‡Ъ‡
ЛТФУО¸БУ‚‡ММУИ ФУ‰ЫНˆЛЛ. ГМУ„ЛВ НУПФУМВМЪ˚
·Ы‰ЫЪ ‚ЪУЛ˜МУ ЛТФУО¸БУ‚‡М˚ Л ЫЪЛОЛБЛУ‚‡М˚, ‚ ЪУ
‚ВПˇ Н‡Н ‚В‰М˚В ‚В˘ВТЪ‚‡ Л ЪˇКВО˚В ПВЪ‡ОО˚
·Ы‰ЫЪ У·‡·УЪ‡М˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ
ФЛВПОВПУ„У ПВЪУ‰‡.
«‡ ·УОВВ ФУ‰У·МУИ ЛМЩУП‡ˆЛВИ ФУ М‡¯ВИ
ФУ„‡ППВ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ У·‡˘‡ИЪВТ¸ Н
ПВТЪМУПЫ ФУТЪ‡‚˘ЛНЫ ЛОЛ ФВ‰ТЪ‡‚ЛЪВО˛
ÍÓÔÓ‡ˆËË LG.
Г˚ УЛВМЪЛЫВПТˇ М‡ У·ВТФВ˜ВМЛВ ˝НУОУ„Л˜ВТНУИ
·ВБУФ‡ТМУТЪЛ, ТЪ‡‚ˇ ТВ·В ˆВО¸˛ „ОУ·‡О¸МЫ˛ Б‡˘ЛЪЫ
УНЫК‡˛˘ВИ ТВ‰˚. ƒУФУОМЛЪВО¸МЫ˛ ЛМЩУП‡ˆЛ˛
У М‡¯ВИ ФУОЛЪЛНВ ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚ ‚˚
ПУКВЪВ М‡ИЪЛ М‡ М‡¯ВП Т‡ИЪВ:
http://www.lge.com/about/environment/html/Recycling.jsp
EPA
(EPA applied model only)
ENERGY STAR
issued by the U.S. Environmental Protection
Agency(EPA).
is a set of power-saving guidelines
As an ENERGY STAR Partner LGE U. S.
A.,Inc. has determined that this product
meets the ENERGY STAR guidelines for
energy efficiency.
NOM MARK
07
(Mexico only)
Regulatory Information cont.
WEEE
(for Europe )
English
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is attached
to a product it means the product is covered by the
European Directive 2002/96/EC.
2.All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by
the government or the local authorities.
3.The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4.For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased the
product.
French
Élimination de votre ancien appareil
1.Ce symbole, représentant une poubelle sur
roulettes barrée d'une croix, signifie que le
produit est couvert par la directive européenne
2002/96/EC.
2.Les éléments électriques et électroniques
doivent être jetés séparément, dans les videordures prévus à cet effet par votre municipalité.
3.Une élimination conforme aux instructions aidera
à réduire les conséquences négatives et risques
éventuels pour l'environnement et la santé
humaine.
4.Pour plus d'information concernant l'élimination
de votre ancien appareil, veuillez contacter votre
mairie, le service des ordures ménagères ou
encore la magasin où vous avez acheté ce
produit.
Italian
Smaltimento delle apparecchiature obsolete
1.Quando su un prodotto è riportato il simbolo di
un bidone della spazzatura barrato da una croce
significa che il prodotto è coperto dalla direttiva
europea 2002/96/EC.
2.Tutti i prodotti elettrici ed elettronici dovrebbero
essere smaltiti separatamente rispetto alla
raccolta differenziata municipale, mediante
impianti di raccolta specifici designati dal
governo o dalle autorità locali.
3.Il corretto smaltimento delle apparecchiature
obsolete contribuisce a prevenire possibili
conseguenze negative sulla salute umana e
sull'ambiente.
4.Per informazioni più dettagliate sullo smaltimento
delle apparecchiature obsolete, contattare il
comune, il servizio di smaltimento rifiuti o il
negozio in cui è stato acquistato il prodotto.
Swedish
Kassering av din gamla apparat
1.När den här symbolen med en överkryssad
soptunna på hjul sitter på en produkt innebär det
att den regleras av European Directive
2002/96/EC.
2.Alla elektriska och elektroniska produkter bör
kasseras via andra vägar än de som finns för
hushållsavfall, helst via för ändamålet avsedda
uppsamlingsanläggningar som myndigheterna
utser.
3.Om du kasserar din gamla apparat på rätt sätt
så bidrar du till att förhindra negativa
konsekvenser för miljön och människors hälsa.
4.Mer detaljerad information om kassering av din
gamla apparat kan får av kommunen,
renhållningsverket eller den butik där du köpte
produkten.
Dutch
Uw oude toestel wegdoen
1.Als het symbool met de doorgekruiste verrijdbare
afvalbak op een product staat, betekent dit dat
het product valt onder de Europese Richtlijn
2002/96/EC.
2.Elektrische en elektronische producten mogen
niet worden meegegeven met het huishoudelijk
afval, maar moeten worden ingeleverd bij
speciale inzamelingspunten die door de lokale of
landelijke overheid zijn aangewezen.
3.De correcte verwijdering van uw oude toestel
helpt negatieve gevolgen voor het milieu en de
menselijke gezondheid voorkomen.
08
Regulatory Information cont.
4.Wilt u meer informatie over de verwijdering van
uw oude toestel? Neem dan contact op met uw
gemeente, de afvalophaaldienst of de winkel
waar u het product hebt gekocht.
Finnish
Vanhojen laitteiden hävittäminen
1.Tämä merkki tuotteessa tarkoittaa, että tuote
kuuluu sähkö- ja elektroniikkalaiteromusta
annetun EU-direktiivin 2002/96/EY
soveltamisalaan.
2.Kaikki elektroniset laitteet ovat ongelmajätettä,
joten ne on toimitettava paikalliseen
keräyspisteeseen.
3.Vanhan laitteen asianmukainen hävittäminen
ehkäisee mahdollisia ympäristöön ja
terveyteen kohdistuvia haittavaikutuksia.
4.Lisätietoa vanhan laitteen hävittämisestä saat
ottamalla yhteyden paikallisiin viranomaisiin,
kierrätyskeskukseen tai myymälään, josta ostit
laitteen.
German
Entsorgung von Altgeräten
1.Wenn dieses Symbol eines durchgestrichenen
Abfalleimers auf einem Produkt angebracht ist,
unterliegt dieses Produkt der europäischen
Richtlinie 2002/96/EC.
2.Alle Elektro- und Elektronik-Altgeräte müssen
getrennt vom Hausmüll über dafür staatlich
vorgesehenen Stellen entsorgt werden.
3.Mit der ordnungsgemäßen Entsorgung des alten
Geräts vermeiden Sie Umweltschäden und eine
Gefährdung der persönlichen Gesundheit.
4.Weitere Informationen zur Entsorgung des alten
Geräts erhalten Sie bei der Stadtverwaltung,
beim Entsorgungsamt oder in dem Geschäft, wo
Sie das Produkt erworben haben.
Danish
Sådan smider du dit gamle apparat ud
1.Når der er et tegn med et kryds over en
skraldespand, betyder det, at produktet er
omfattet af EU-direktiv 2002/96/EC.
2.Alle elektriske og elektroniske produkter skal
smides ud et andet sted end gennem den
kommunale affaldsordning ved hjælp af specielle
indsamlingsfaciliteter, der er organiseret af staten
eller de lokale myndigheder.
3.Korrekt bortskaffelse af dit gamle apparat er med
til at forhindre mulige skadevirkninger på miljøet
og menneskelig sundhed.
4.Mere detaljerede oplysninger om bortskaffelse af
dit gamle apparat kan fås ved at kontakte dit
lokale kommunekontor, renovationsselskab eller
den butik, hvor du købte produktet.
Greek
∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜
1.ŸЩ·У ¤У· ЪФ˚fiУ ‰И·ı¤ЩВИ ЩФ ‰‡М‚ФПФ ВУfi˜
‰И·БЪ·ММ¤УФ˘ О¿П·ıФ˘ ·ФЪЪИММ¿ЩˆУ, ЩfiЩВ ЩФ ЪФ˚fiУ
О·П‡ЩВЩ·И ·fi ЩЛУ E˘Ъˆ·˚О‹ O‰ЛБ›· 2002/96/EOK.
2.H ·fiЪЪИ„Л fiПˆУ ЩˆУ ЛПВОЩЪИОТУ О·И ЛПВОЩЪФУИОТУ
ЪФ˚fiУЩˆУ Ъ¤ВИ У· Б›УВЩ·И ¯ˆЪИЫЩ¿ ·fi Щ· БВУИО¿
ФИОИ·О¿ ·ФЪЪ›ММ·Щ· М¤Ыˆ О·ıФЪИЫМ¤УˆУ
ВБО·Щ·ЫЩ¿ЫВˆУ Ы˘ППФБ‹˜ ·ФЪЪИММ¿ЩˆУ, ФИ ФФ›В˜
¤¯Ф˘У ‰ЛМИФ˘ЪБЛıВ› В›ЩВ ·fi ЩЛУ О˘‚¤ЪУЛЫЛ ‹ ·fi ЩИ˜
ЩФИО¤˜ ·Ъ¯¤˜.
3.H ЫˆЫЩ‹ ·fiЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜ ı·
‚ФЛı‹ЫВИ ЫЩЛУ ·ФЩЪФ‹ Иı·УТУ ·ЪУЛЩИОТУ Ы˘УВИТУ
ˆ˜ ЪФ˜ ЩФ ВЪИ‚¿ППФУ О·И ЩЛУ ˘БВ›· ЩФ˘ ·УıЪТФ˘.
4.°И· ИФ ПВЩФМВЪВ›˜ ПЛЪФКФЪ›В˜ Ы¯ВЩИО¿ МВ ЩЛУ
·fiЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜, ВИОФИУˆУ‹ЫЩВ МВ
ЩФ ·ЪМfi‰›Ф ЩФИОfi БЪ·КВ›Ф, ˘ЛЪВЫ›· ‰И¿ıВЫЛ˜ ФИОИ·ОТУ
·ФЪЪИММ¿ЩˆУ ‹ ЩФ М·Б·Н› ·fi ЩФ ФФ›Ф ·БФЪ¿Ы·ЩВ ЩФ
ЪФ˚fiУ.
Spanish
Cómo deshacerse de aparatos eléctricos y
electrónicos viejos
1.Si en un producto aparece el símbolo de un contenedor
de basura tachado, significa que éste se acoge a la
Directiva 2002/96/CE.
2.Todos los aparatos eléctricos o electrónicos se deben
desechar de forma distinta del servicio municipal de
recogida de basura, a través de puntos de recogida
designados por el gobierno o las autoridades locales.
3.La correcta recogida y tratamiento de los dispositivos
inservibles contribuye a evitar riesgos potenciales para el
medio ambiente y la salud pública.
4.Para obtener más información sobre cómo deshacerse de
sus aparatos eléctricos y electrónicos viejos, póngase en
contacto con su ayuntamiento, el servicio de recogida de
basuras o el establecimiento donde adquirió el producto.
09
Regulatory Information cont.
Portuguese
Hungarian
Slovak
Polish
Czech
Croatian
10
Regulatory Information cont.
Estonian
Latvian
Lithuanian
11
Loading...