LG M1717A-BM User Manual

Safety Precautions

Please read these safety precautions carefully before using the product.

Warning If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.

Caution If you ignore the caution message, you may be slightly injured or the product may be damaged

Precautions in installing the Product

Warning

Keep away from heat sources like electrical heaters.

- Electrical shock, fire, malfunction or deformation may occur.

Keep the packing anti-moisture material or vinyl packing out of the reach of children.

-Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.

Do not put heavy objects on the product or sit upon it.

- If the product collapses or is dropped, you may be injured. Children must pay particular attention.

Do not leave the power or signal cable unattended on the pathway.

- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.

Install the product in a neat and dry place.

- Dust or moisture can cause electrical shock, fire or product damage.

If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center.

- If you continue to use without taking proper measures, electrical shock or fire can occur.

If you dropped the product or the case is broken, turn off the product and unplug the power cord.

-If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable objects such as paper and matches. Children must pay particular attention.

-Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service center.

Caution

Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (more than 10cm from the wall)

- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.

Do not block the ventilation hole of the product by a tablecloth or curtain.

- The product can be deformed or fire can break out due to overheating inside the product.

Install the product on a flat and stable place that has no risk of dropping the product.

- If the product is dropped, you may be injured or the product may be broken.

Install the product where no EMI occurs.

Keep the product away from direct sunlight.

- The product can be damaged.

Electrical Power Related Precautions

Warning

Make sure to connect the power cable to the grounded current.

- You may be electrocuted or injured.

Use the rated voltage only.

- The product can be damaged, or you may be electrocuted.

During a thunder or lightning storm, unplug the power cable or signal cable.

- You may be electrocuted or a fire can break out.

Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a power bar with a grounding terminal designed for exclusive use with the computer.

- A fire can break out due to overheating.

Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.

- You may be electrocuted due to excess moisture.

If you don’t intend to use the product for a long time, unplug the power cable from the product.

- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.

Fix the power cable completely.

- If the power cable is not fixed completely, a fire can break out.

Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put heavy objects on the power cord.

- The power line can be damaged, which may cause electric shock or fire.

Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal.

- You may be electrocuted.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Caution

Do not unplug the power cord while the product is in use.

- Electrical shock can damage the product.

Precautions in Moving the Product

Warning

Make sure to turn off the product.

- You may be electrocuted or the product can be damaged.

Make sure to remove all cables before moving the product.

- You may be electrocuted or the product can be damaged.

<![if ! IE]>

<![endif]>ENGLISH

Safety Precautions

Caution

Do not shock the product when moving it.

- You may be electrocuted or the product can be damaged.

Do not dispose the product-packing box. Use it when you move.

Make the panel face forward and hold it with both hands to move.

-If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair.

Precautions in Using the Product

Warning

Do not disassemble, repair or modify the product at your own discretion.

-Fire or electric shock accident can occur.

-Contact the service center for check, calibration or repair.

When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent scratching. Do not clean with a wet cloth.

Keep the product away from water.

- Fire or electric shock accident can occur.

Caution

Do not put or store inflammable substances near the product.

- There is a danger of explosion or fire due to careless handling of the inflammable substances.

When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent scratching. Do not clean with a wet cloth.

- The water can sink into the product, which can cause electric shock or serious malfunction.

Take a rest from time to time to protect your vision.

Keep the product clean at all times.

Take a comfortable and natural position when working with a product to relax the muscles.

Take a regular break when working with a product for a long time.

Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it.

Keep the proper distance from the product.

- Your vision may be impaired if you look at the product too closely.

Set the appropriate resolution and clock by referring to the User’s Guide.

- Your vision can be impaired.

Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)

- Product can be deformed.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury.

Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

Accessories

Please check the accessories in the product package.

* The product and the accessories can be different from the figures shown here.

<![if ! IE]>

<![endif]>ENGLISH

Remote Control/Batteries	CD-ROM/	D-Sub Signal Cable
	Cards

Power Cable

Audio Cable (PC)

Stand base

Inserting batteries into remote control.

1. Take out the battery cap.

2. Insert the batteries with correct polarity (+/-).

3. Close the battery cap.

• You can use a remote control 7 meter distance and

30 degree (left/right) within the receiving unit scope.

• Dispose of used batteries in the recycle bin to prevent environmental pollution.

Before Connecting to the PC

Before setting up the product, ensure that the power to the product, the computer system, and other attached devices is turned off.

Connecting the stand base

Place the product with its front facing downward on a soft cloth.

Align the hooks on the stand base with the matching slots in the base ofthe product.

Insert the hooks into slots.

Slot

Bottom Latch

Removing the stand base

Place the product with its front facing downward on a soft cloth.

To remove the stand base, hold the bottom of the stand with one hand and pull the base bottom latch with the other hand, as shown in the figure.

Important

Once you connect the stand base, try not to disconnect it.

Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

Before setting up the product, ensure that the power to the product, the computer system, and other attached devices is turned off.

Positioning your display

1. Adjust the position of the panel in various ways for maximum comfort.

Tilt Range -3˚~25˚

Swivel :345˚

<![if ! IE]>

<![endif]>ENGLISH

Name and Function of the Parts

Name of the Remote Control Buttons

MUTE Button

•Input Select Button

•TV Button (See next page)

FAV Button

Favorite channel button.

Volume ( ) Button

Set Button

Channel Number Select Button

Operational at the TV mode only

AUDIO Button

Use this button to select the sound tone. Press repeatedly to select Flat, Music, Movie, Sports, User sound tone.

CC Button

Select a closed caption

FLASH BK Button

Turn to the last channel viewed.

MUTE POWER

TV INPUT MTS

FAV

EXIT

ENTER

VOL

AUDIO VIDEO

CC FLASHBK SLEEP

Power On/Off Button

MTS(Sound Mode Select) Button

Press repeatedly to select Mono, Stereo, SAP sound tone.

But Stereo, SAP mode are available only if included on the broadcast signal.

•EXIT Button

•MENU Button

Channel ( ) Button

VIDEO Button

When watching AV/TV

- Automatically adjusts the image.

Press this button repetitively to set the intended screen.

SLEEP Button

When watching AV/TV/PC

-The screen will be automatically turned off after a certain period of time.

Press this button repetitively to select an appropriate time duration.

MUTE		POWER
TV	INPUT	MTS
FAV	EXIT	MENU

ENTER

VOL

AUDIO VIDEO

CC FLASHBK SLEEP

• Input Select Button

Each time you press the Input button it will change to

TV Video

RGB-DTV RGB-PC. If nothing is inputted for several seconds the screen will automatically move to the selected menu.

Input

Video

RGB-DTV

RGB-PC

<![if ! IE]>

<![endif]>ENGLISH

Name and Function of the Parts

Rear View

	RGB(PC/DTV)		ANTENNA
	RGB(PC/DTV)
			Audio
Video	[MONO]	Audio	H/P
	AV IN		S-Video

Power Connector : Connect the power cord.

AV Input Terminal

D-Sub Analog Signal Connector

TV Tuner Jack : Connect the antenna.

PC Sound Jack : Connect to the jack in the PC sound card.

Headphone/Earphone Connection Terminal

AV Input Terminal

Video [MONO]	Audio
AV IN

S-Video

<![if ! IE]>

<![endif]>ENGLISH

Video Input Terminal

Audio Input Terminal

S-Video Input Terminal

Connecting the sound card output terminal

• Make sure to check the sound card connection terminal in the PC before connecting to the product.

If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumper or the PC application. (For more details, refer to the sound card user’s guide.)

-Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.

-*Line Out : The terminal connected to the speaker equipped with an amplifier.

If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This product is integrated with an amplifier.

A10