LG LW6424 User Manual [ru]
OWNER'S MANUAL
High Definition
Network Dome Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LW6424 series
LW6454 series
P/NO : MFL62591949 1010 (V1.0)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
t A suitable conduit entries, knock-outs or glands shall be pro-
vided in the cable entries of this product in the end user.
t Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
t Holes in metal, through which insulated wires pass, shall have
smooth well rounded surfaces or shall be provided with brushings.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2
Warning: Do not install this equipment in a confined space such as
a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose this
product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
To disconnect power from mains, pull out the mains cord plug.
When installing the product, ensure that the plug is easily accessible.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
EEE Compliance with Directive. (for Turkey only)
3
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
4
Cautions for Safe Operation
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be cautious
not to get combustible or metallic material inside the body. If used
with foreign matter inside, the device is liable to fail or to get cause
of fire or electric shock.
t Remove dust or dirt on the surface of the lens with a blower.
t Use a dry soft cloth to clean the body. If it is very dirty, use a
cloth dampened with a small quantity of neutral detergent then
wipe dry.
t Avoid the use of volatile solvents such as thinners, alcohol, ben-
zene and insecticides.
They may damage the surface finish and/or impair the operation
of the device.
Operating and storage location
Avoid viewing a very bright object (such as light fittings) during an
extended period. Avoid operating or storing the unit in the following locations.
t Extremely hot or cold places (operating temperature from -10 °C
to 50 °C, however, we recommend that the unit be used within a
temperature range from 0 °C to 45 °C)
t Damp or dust place
t Places exposed to rain
t Places subject to strong vibration
t Close to generators of powerful electromagnetic radiation such
as radio or TV transmitters.
5
Contents
Introduction ................................................................................... 7
Part names and Functions .................................................................8
Connections ................................................................................. 10
Precautions ........................................................................................... 10
Connection Overview ....................................................................... 10
Connecting Network.........................................................................11
Connecting Power Source .............................................................. 12
Connecting Alarm Device ...............................................................13
Connecting Microphone and Speaker Device .........................14
Mounting the camera ....................................................................... 15
Operation and settings ............................................................... 21
Reference .....................................................................................52
Troubleshooting ................................................................................. 52
Open source software notice .........................................................55
Specications.......................................................................................58
Before using the system .................................................................. 21
Recommended PC Requirements ................................................ 21
Accessing the LG IP device..............................................................22
LG Smart Web Viewer Overview ...................................................23
Conguring the LG IP camera ........................................................25
OSD Menu Setup ................................................................................41
6 Contents
Introduction
The LG Network Camera is designed to use on an Ethernet network
and must be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the
LG Network Camera in your networking environment. Some knowledge of networking environments would be beneficial to the reader.
Should you require any technical assistance, please contact authorized service center.
Features
The LG Network Dome Camera offers the following functions:
t Dual H.264 Stream for single Video Input
t Multi-Codec (H.264, MJPEG) Streaming
t Intelligent Video Analysis (Option)
t PoE (Power over Ethernet) Support (802.3af)
t 2 Power (DC 12 V, PoE) Support
t Audio Support (G.711, G.726 Full Duplex)
t Pre/Post Alarm Support
Features Chart
This table shows the differences between the models.
LW6454 is used for the description, operations and details provided
in this manual.
Models LW6424 LW6454
VCA No Yes
Accessories
t Program CD
t Owner’s Manual
t Installation sticker
t Fixing screw & hexagonal wrench
t Vandal Proof Support (IP66)
t High resolution and high sensitivity with a 6.49 mm progressive
scan CMOS.
t Day & Night function
t ABF Auto Back Focus function
Introduction 7
Part names and Functions
a Dome Cover Ring
b Dome Cover
c Fall Prevention rubber band
a
b
c
d
e
f
g
h
i
Fixes the rubber band into the dome cover.
d Lens Cover
e Azimuth adjuster
Adjusts the azimuth angle to obtain a level image.
f Focus lock lever
Fixes the focus position after adjusting.
g Zoom lock lever
Fixes the zoom position after adjusting.
h Tilting lock screw
Fixes the tilting position after adjusting.
i Video Out connector
Supplies analog video signal (composite) to the connected
device.
j ABF Auto Back Focus button
ABF Auto Back Focus is an adjustable function for the back
focus automatically. Before you use it, you should set the
zoom and focus of the lens approximately. If you press this
button, the camera will be activated to adjust the back
focus automatically. If you keep pressing this button about 4
seconds, the focus reset function will be activated.
j
k
l
m
k OSD Setup menu control buttons
Use to set the OSD Setup menu.
l RESET button
Push the button more than 3 seconds, this would restore the
factory default network related settings.
m Pan adjuster
Adjusts the pan position.
8 Introduction
n
o
p
q
r
s
n ETHERNET/POE Port
Connects to a PC or a network via a hub with a
10 BASE-T/100 BASE-TX cable attached RJ-45 connector.
Note:
Power over Ethernet (PoE) is a technology that integrates
power into a standard LAN infrastructure. It enables power
to be provided to the network device, such as a network
camera, using the same cable as that used for network
connection. It eliminates the need for power outlets at the
device locations and enables easier application of uninterruptible power supplies (UPS).
o ALARM IN / ALARM IN RETURN
Provides physical interface for sensor.
ALARM OUT / ALARM OUT RETURN
Provides physical interface for Alarm/Relay.
p AUDIO OUT (Line Level Output)
t
Connect to an active speaker with a built-in amplifier.
q AUDIO IN (Line Level Input)
Input for a mono microphone, or a line-in mono signal.
r Power input jack
Connects to a DC 12 V power supply using proper cables.
s Camera mounting bracket
TM
t GORE
Do not remove the GORE
protective sticker / Air vent system
TM
protection sticker. It helps the
flow of air to prevent moisture and condensation inside of
the camera. This air vent system helps the product’s reliability and stability so it increases the life cycle.
Introduction 9
Connections
Precautions
t Be sure to switch off the unit before installation and connection.
t The installation should be made by qualified service personnel or system installers.
t Do not expose the power and connection cables to moisture, which may cause damage to the unit.
Connection Overview
PoE Device
(IEEE802.3af)
10 Connections
Connecting Network
You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or
monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.
Connect the IP camera to your network using a standard RJ-45 network cable as shown below.
Broadband
Service
Broadband
Service
Router
PoE Device
(IEEE802.3af)
ETHERNET
With POE
Connections 11
Connecting Power Source
Connect power, using one of the methods listed below:
To use the power adapter
Connect a DC 12 V power source to the power input terminal as shown below.
(recommended power adapter is DC 12 V/1.5 A or above)
(Connect to the DC 12 V UL Listed, Class 2 Power Supply only on the unit. )
POWER IN
DC 12 V
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE device.
ETHERNET
With POE
PoE Device
(IEEE802.3af)
Note:
If the camera doesn’t work properly after connecting PoE device, please check if the PoE device supplies enough power.
12 Connections
Connecting Alarm Device
Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches, etc.
ALARM IN / ALARM IN RETURN (Sensor Input)
Connect the sensor device to the sensor input terminal.
GREEN
Sensor Device
GREEN-ALARM IN
BLACK
ALARM OUT / ALARM OUT RETURN (Relay Output)
GREEN-ALARM IN
BLACK-ALARM IN
BLACK-ALARM IN
RETURN
RED-ALARM OUT
WHITE-ALARM OUT
WHITE-ALARM OUT
RETURN
RETURN
RED-ALARM OUT
RETURN
Connect the alarm (relay) device to the relay output terminal. Alarm signal is outputted at an event occurrence.
GREEN-ALARM IN
GREEN-ALARM IN
BLACK-ALARM IN
BLACK-ALARM IN
RED
RETURN
RED-ALARM OUT
WHITE-ALARM OUT
WHITE-ALARM OUT
RETURN
RETURN
RED-ALARM OUT
RETURN
Alarm (relay) Device
WHITE
Note: The Photo MOS Relay is rated for 100 mA at 20 V DC or 100 mA at 28 V AC.
Connections 13
Connecting Microphone and Speaker Device
Optionally connect an active speaker and/or external microphone with a built-in amplifier.
AUDIO OUT
AUDIO IN
Note:
Keep the microphone away from the speaker to avoid howling.
14 Connections
Mounting the camera
You can mount the camera on a ceiling or wall.
Surface mount
Follow the instructions below to surface mount the camera.
1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest. Using
the template as a guide, make a hole through the ceiling.
3. Fasten the camera assembly bracket to the ceiling.
2. Pass the connection cable through the inner side of the ceiling.
Connections 15
4. Connect the cables to the cable jacks of the camera body. 5. Assemble the camera and mounting bracket. Connect the unit
by following step a and b.
16 Connections
Wall mount (Optional)
Follow the instructions below to install the camera with a wall
mount.
1. Drill holes in the wall where you want to install the wall mount.
2. Install the wall mount installation bracket.
3. Install the wall mount assembly as shown below.
Connections 17
4. Connect the cables to the camera jack. 5. Attach the camera to the wall mount assembly.
18 Connections
Loading...