LG LW6354 User Manual

OWNER'S MANUAL

High Definition
Network Dome Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL

LW6324 series
LW6354 series

P/NO : MFL67182707 1106 (V1.0)

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be pro­vided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have
smooth well rounded surfaces or shall be provided with brush­ings.

FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose the
authority to operate this equipment if an unauthorized change or
modification is made.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.

2 Safety Information

Warning: Do not install this equipment in a confined space such as

a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose this
product to rain or moisture.
Caution: This installation should be made by a qualified service
person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, shall be
placed on the apparatus.

To disconnect power from mains, pull out the mains cord plug.
When installing the product, ensure that the plug is easily
accessible.

LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : [phone])

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.

3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.

4. For more detailed information about disposal of
your old appliance, please contact your city office,
waste disposal service or the shop where you
purchased the product.

EEE Compliance with Directive. (for Turkey only)

Safety Information 3

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of the polarized or grounding­type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.

10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused
for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.

4 Safety Information

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious
not to get combustible or metallic material inside the body. If used
with foreign matter inside, the device is liable to fail or to get cause
of fire or electric shock.

• Remove dust or dirt on the surface of the lens with a blower.

• Use a dry soft cloth to clean the body. If it is very dirty, use a

cloth dampened with a small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such as thinners, alcohol,
benzene and insecticides.
They may damage the surface finish and/or impair the operation
of the device.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during
an extended period. Avoid operating or storing the unit in the
following locations.

• Extremely hot or cold places (operating temperature from -10 °C
to 50 °C, however, we recommend that the unit be used within a
temperature range from 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful electromagnetic radiation such

as radio or TV transmitters.

Safety Information 5

Contents

Safety Information ........................................................................ 2

Introduction ................................................................................... 7

Part names and Functions .................................................................8

Connections .................................................................................10

Precautions ...........................................................................................10

Connection Overview .......................................................................10

Connecting Network.........................................................................11

Connecting Power Source ..............................................................12

Connecting Alarm Device ............................................................... 13

Connecting Microphone and Speaker Device .........................14

Using the micro SD card .................................................................. 15

Mounting the camera .......................................................................17

Operation and settings ...............................................................23

Before using the system ..................................................................23

Recommended PC Requirements ................................................ 23

Accessing the LG IP device..............................................................24

LG Smart Web Viewer Overview ...................................................25

Conguring the LG Network Camera Device ...........................26

OSD Menu Setup ................................................................................ 43

Reference ..................................................................................... 56

Troubleshooting .................................................................................56

Open source software notice .........................................................59

Specications.......................................................................................62

6

Introduction

The LG Network Camera is designed to use on an Ethernet network
and must be assigned an IP address to make it accessible.

This manual contains instructions on how to install and manage
the LG Network Camera in your networking environment. Some
knowledge of networking environments would be beneficial to the
reader.

Should you require any technical assistance, please contact
authorized service center.

Features

The LG Network Dome Camera offers the following functions:

• Dual H.264 Stream for single Video Input

• Multi-Codec (H.264, MJPEG) Streaming

• Intelligent Video Analysis (Option)

• PoE (Power over Ethernet) Support (802.3af )

• 2 Power (DC 12 V, PoE) Support

• Audio Support (G.711, G.726 Full Duplex)

• Pre/Post Alarm Support

• Vandal Proof Support (IP66)

• High resolution and high sensitivity with a 6.08 mm progressive

scan CMOS.

• Auto Expouse

• Day & Night function

• WDR (Wide Dynamic Range) is available

• ABF Auto Back Focus function

Features Chart

This table shows the differences between the models.

LW6354 is used for the description, operations and details provided
in this manual.

Models LW6324 LW6354

VA No Yes

Accessories

• Program CD

• Owner’s Manual

• Installation sticker

• Fixing screw & hexagonal wrench

Introduction 7

Part names and Functions

a

b

c

d

e
f
g
h
i

j
k
l
m

a Dome Cover Ring
b Dome Cover
c Fall Prevention rubber band

Fixes the rubber band into the dome cover.

d Lens Cover
e Azimuth adjuster

Adjusts the azimuth angle to obtain a level image.

f Focus lock lever

Fixes the focus position after adjusting.

g Zoom lock lever

Fixes the zoom position after adjusting.

h Tilting lock screw

Fixes the tilting position after adjusting.

i Video Out connector

Supplies analog video signal (composite) to the connected
device.

j ABF Auto Back Focus button

ABF Auto Back Focus is an adjustable function for the back
focus automatically. Before you use it, you should set the
zoom and focus of the lens approximately. If you press this
button, the camera will be activated to adjust the back
focus automatically. If you keep pressing this button about 4
seconds, the focus reset function will be activated.

k OSD Setup menu control buttons

Use to set the OSD Setup menu.

l RESET button

Push the button more than 3 seconds, this would restore the
factory default network related settings.

m Pan adjuster

Adjusts the pan position.

8 Introduction

n

o

p
q
r

s
t
u

v

n micro SD card slot

Insert the micro SD card.

o micro SD card condition indicator

Lights when the micro SD card is activated normally.

Blinks when the recording is in progress on the micro SD
card.

p ETHERNET/POE Port

Connects to a PC or a network via a hub with a
10 BASE-T/100 BASE-TX cable attached RJ-45 connector.

q ALARM IN / ALARM IN RETURN

Provides physical interface for sensor.

ALARM OUT / ALARM OUT RETURN

Provides physical interface for Alarm/Relay.

r AUDIO OUT (Line Level Output)

Connect to an active speaker with a built-in amplifier.

s AUDIO IN (Line Level Input)

Input for a mono microphone, or a line-in mono signal.

t Power input jack

Connect to a DC 12 V power supply using proper cables.

u Camera mounting bracket
v GORETM protective sticker / Air vent system

Do not remove the GORETM protection sticker. It helps the
flow of air to prevent moisture and condensation inside
of the camera. This air vent system helps the product’s
reliability and stability so it increases the life cycle.

Introduction 9

Connections

Precautions

• Be sure to switch off the unit before installation and connection.

• The installation should be made by qualified service personnel or system installers.

• Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connection Overview

PoE Device

(IEEE802.3af)

10 Connections

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or
monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

Broadband

Service

Router

ETHERNET
With PoE

PoE Device

(IEEE802.3af)

Broadband

Service

Connections 11

Connecting Power Source

ETHERNET
With PoE

Connect power, using one of the methods listed below.

To use the power adapter

Connect a DC 12 V power source to the power input
terminal as shown below.
(recommended power adapter is DC 12 V/1.5 A or above)

(Connect to the DC 12 V UL Listed, Class 2 Power Supply
only on the unit. )

POWER IN
DC 12 V

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit. You
must use the “IEEE802.3af” standard PoE device.

PoE Device

(IEEE802.3af)

ETHERNET
With PoE

Note:

• Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It enables power to be provided
to the network device, such as a network camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power supplies (UPS).

• If the camera doesn’t work properly after connecting PoE device, please check if the PoE device supplies enough power.

12 Connections

Connecting Alarm Device

GREEN-ALARM IN
BLACK-ALARM IN
RETURN
RED-ALARM OUT
WHITE-ALARM OUT
RETURN

Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches, etc.

ALARM IN / ALARM IN RETURN (Sensor Input)

Connect the sensor device to the sensor input terminal.

GREEN

Sensor Device

GREEN-ALARM IN

BLACK

ALARM OUT / ALARM OUT RETURN (Relay Output)

Connect the alarm (relay) device to the relay output terminal. Alarm signal is outputted at an event occurrence.

RED

Alarm (relay) Device

WHITE

GREEN-ALARM IN

BLACK-ALARM IN

BLACK-ALARM IN

RETURN
RED-ALARM OUT

RED-ALARM OUT

WHITE-ALARM OUT

WHITE-ALARM OUT

RETURN

GREEN-ALARM IN

GREEN-ALARM IN

BLACK-ALARM IN

BLACK-ALARM IN

RETURN
RED-ALARM OUT

RED-ALARM OUT

WHITE-ALARM OUT

WHITE-ALARM OUT

RETURN

RETURN

RETURN

RETURN

RETURN

Note: The Photo MOS Relay is rated for 100 mA at 20 V DC or 100 mA at 28 V AC.

Connections 13

Connecting Microphone and Speaker Device

Optionally connect an active speaker and/or external microphone with a built-in amplifier.

AUDIO OUT

AUDIO IN

Note:

Keep the microphone away from the speaker to avoid howling.

14 Connections

Using the micro SD card

You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover Ring and Dome cover.

2. Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the micro
SD card to fix it at the last step.

Notes:

• Do not use the power too much when you insert the micro SD
card. The micro SD card may be damaged.

• If you insert the micro SD card in the wrong position, the micro
SD card may be damaged or it may cause the malfunction of the
micro SD Card Slot.

• Keep the terminal part of the micro SD card in clean. Be careful
the terminal part of the micro SD card not to dusty.

• As the micro SD card is consumable, the micro SD card end its
days and may be not able to save data if you use it more than
over certain times. In this case, replace micro SD card to buy a
new one.

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock
condition.

Connections 15

2. Take the micro SD card out carefully from the camera. It may
cause a malfunction of the micro SD card or the micro SD card
slot if you use the power too much at lock status.

Caution:

• If you install the micro SD card on the camera and remove
with the micro SD card condition indicator lights on, you
must unmount the micro SD card by using the [SD Card >
Configuration > Disk Management > Unmount] menu. The
micro SD card data is compromised or the camera may not
operate normally, if you remove the card without use [Unmount]
function.

• LG Electronics is not responsible for deleted data caused by user
mishandling when you insert or remove the micro SD card.

Recommended the micro SD card specification

Maker Capacity

LG

Sandisk

Transcend

Less than 32 GB 32 kbyte

Block Size

(FAT 32)

Note

Speed of reading
and writing more

than 10 MB/Sec.

(Class 6)

16 Connections

Mounting the camera

You can mount the camera on a ceiling or wall.

Surface mount

Follow the instructions below to surface mount the camera.

1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of interest.
Using the template as a guide, make a hole through the ceiling.

2. Pass the connection cable through the inner side of the ceiling.

3. Fasten the camera assembly bracket to the ceiling.

Connections 17

4. Connect the cables to the cable jacks of the camera body. 5. Assemble the camera and mounting bracket. Connect the unit

by following step a and b.

18 Connections

Wall mount (Optional)

Follow the instructions below to install the camera with a wall
mount.

1. Drill holes in the wall where you want to install the wall mount.

2. Install the wall mount installation bracket.

3. Install the wall mount assembly as shown below.

Connections 19

4. Connect the cables to the camera jack. 5. Attach the camera to the wall mount assembly.

20 Connections

Pendant mount (Optional)

Follow the instructions below to install the camera with a pendant
mount.

1. Drill holes on the wall where you want to install the pendant
mount.

2. Pass the connection cable through the pendant mount assembly
so that they hang down.

3. Install the pendant mount assembly.

Connections 21

4. Connect the cables to the camera jacks. 5. Attach the camera to the pendant mount assembly.

22 Connections

Operation and settings

Before using the system

• Before using the LG IP device make sure the connections are
correct and verify whether proper power supply is used.

• Check the connections of the LG IP device for the correct
conditions.

• Check that the LG IP device is(are) connected to the network and
that power is supplied.

• Once the connections are made you need to install the LG client
program to the PC from which you want to access the device.
The LG Smart Web Viewer program is automatically installed
when you connect the LG IP device.
The LG Smart Station and the LG Smart Web Viewer program
are the network program of the LG Video Server and the LG IP
cameras.

• To view streaming video in Internet Explorer, set your browser
to allow ActiveX controls. If you find this message “This website
wants to install the following add-on: ‘IPCam_Streamer.cab’ from
‘LG ELECTRONICS INC’”, Click the yellow bar and install LG Smart
Web Viewer Program on your computer.

• The Layouts and the Live view pages may differ with different OS
(Operating Systems) and Web Browsers.

• Care needs to be taken not to run any other applications when
the Client Program is running as it may cause memory shortage.

Recommended PC Requirements

The LG IP device can be used with most standard operating systems
and browsers.

Items Requirements

Operating System

CPU

Web Browser

DirectX DirectX 9.0 or above

Memory 2 GB or above RAM

Graphics Card 256 MB or above Video RAM

Resolution 1 280 x 1 024 (with 32 bit color) or higher

Windows XP Professional,
Windows VISTA, Windows 7

Intel Core2 Quard Q6700 (2.66 GHz) or
above

Microsoft Internet Explorer above the
version 6.0 and below the version 8.0.

Operation and settings 23

Accessing the LG IP device

You can access the LG IP device by following the below steps.

1. Install LG Smart Station Program

2. Discover the LG IP device using the IP Utility

The IP Utility can automatically discover and display LG IP
devices on your network.

The IP Utility shows the MAC address, IP address, Model
name and so on.

Note:

The computer running the IP Utility must be on the same
network segment (physical subnet) as the LG IP device.

2.1 Run the IP Utility program.

2.2 Click the [Search] button or select the [Search] option
in the Device search menu.
After a few seconds the found LG IP devices gets dis­played in the IP Utility window.

3. Logging in to the LG Smart Web Viewer

The LG Smart Web Viewer can be used with most web
browsers. The recommended browser is Internet Explorer
with Windows.

3.1 Run the IP Utility and find the LG IP devices.

3.2 When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on the
same IP address and select “Connect to Web Page”
to start the LG Smart Web Viewer. When accessing
the LG Smart Web Viewer, the authentication dialog

appears on the screen.

3.3 Enter the user name and password. (Note that the
default administrator user name and password are
“admin”.)

3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.

Notes:

• You can also access the LG Smart Web Viewer as shown

below.

3.1 Start your Web browser.

3.2 Enter the IP address of the LG IP device in the address
bar of the browse.

3.3 Enter the user name and password set by the
administrator.

3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.

• The LG Smart Web Viewer needs more time to display it
according to the network conditions.

• If the login window is not displayed, check the pop-up
blocker. If you set the pop-up blocker, the login window
is not displayed. You must allow the pop-ups.

• If you connect the LG Smart Web Viewer for the first time,
the Security Warning window is displayed to install the
LG Smart Web Viewer program. You must install the LG
Smart Web Viewer program for using the LG IP device.

• If your computer or network is protected by a proxy or
firewall, the proxy or firewall settings can prevent the LG
Smart Web Viewer program. Change the proxy or firewall
settings to activate the LG Smart Web Viewer program.

24 Operation and settings

LG Smart Web Viewer Overview

Item Description

Select the video image size from the
drop-down list. (1 280 x 1 024 (4:3 mode),
1 280 x 720 (16:9 mode), D1 or CIF)
The initial view size is set to D1.

Displays the current video codec of the
selected video stream (Master or Slave).

Check this option as the network
connection type (TCP or UDP). If you
check it, the client connects to the server
using TCP connection.

Click to save the current image in JPEG
format on your computer.

1. Click the [Snapshot] button and then
the Snapshot window is displayed.

2. Click the [Save] button in the
Snapshot window.

3. Enter the file name (JPEG format) and
select the folder to save it.

4. Click the [Save] button to confirm it.

5. Click the [Close] button in the
Snapshot window to close it.

Displays the Camera OSD control
window. Use these buttons to setup the
Camera. This button does not appear on
the screen if the login is other than the
administrator.

Select the video stream. From the Live
view drop-down list, select the desired
video image source between [Master-0]
and [Slave-0].

Note:

Master and Slave are output video
streams. You can set the stream
configurations independently for either
Master or Slave stream. This would
facilitate the user to set the live view at
his comfort.

Operation and settings 25

Provides all the necessary tools
for setting up the device to your
requirements. The user will need
administrator level to do this.

Note:

If you want to exit the Configuration
menu, select one of the video stream in
the Live view drop-down list.

Displays the current surveillance live
screen. You can monitor the camera
image on the live view window of the LG
Smart Web Viewer.

Click this button to connect or
disconnect the audio communication
between the LG IP device and the
connected PC.

(Color icon: On, Gray scale icon: Off.)
Click this button to switch the

microphone off and on for the computer.

(Color icon: On, Gray scale icon: Off.)
Click this button to switch the sound off

and on, for the speaker of the computer.

(Color icon: On, Gray scale icon: Off.)

Conguring the LG Network Camera
Device

The features and options of the LG IP camera are configured
through the Configuration menu.

Only administrator-level users have permission to access the
Configuration menu.

Accessing the Conguration menu

Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.

Warning

The Configuration setup should be made by qualified service
personnel or system installers.

26 Operation and settings

System settings

Version

Displays the current version of Firmware, Hardware, Software and
Web Client.

Date & Time

Time zone

Set the time difference from GMT in the area where the IP device
is installed. Select the time zone in the area where the IP device is
installed from the drop down list.

Time mode

> Synchronize with NTP Server: Select if you want to

synchronize the IP device’s date and time with those of the
time server called NTP (Network Time Protocol). Specify the
NTP server’s name. Click the [Test] button for connection test
to the server.

> Synchronize with personal computer: Select if you want

to synchronize the IP device’s date and time with your
computer.

> Synchronize manually: Select if you want to set the IP

device’s date and time manually. Select the year, month and
date by clicking the calendar button. Set hour, minutes and
seconds in the edit boxes.

Notes:

• When system reboot after time setting, time of system
could be delayed. If you set the time correctly, set the
[Synchronize with NTP server] option.

• Refer to NTP configuration as operation system of the
Recording Server when the Recording Server use record­ing function and NTP server.

Server time

> Server time: Displays the current date and time of the IP

device.

• Save: Click this button to confirm the settings.

Operation and settings 27

Maintenance

System reboot

Click the [Reboot] button to restart the IP device. It takes some
minutes for the IP device to start again.

Restore and backup

> Backup: To take a backup all of the settings. If necessary, it

make possible to return to a backuped configuration.

1. Click the [Backup] button.

2. Click the [Save] button.

3. Follow the instructions on the browser to specify the
folder.

4. Click the [Save] button to save the settings.

> Restore:

1. Click the [Browse] button.

2. Find and open the file in which the configuration setting
data is stored.

3. Click the [Restore] button and the system settings will be
restored and reboot the system.

Notes:

• Backup and Restore can happen on IP device having the
same version of firmware. This feature is not intended for
multi-configurations or for firmware upgrades.

• [Backup] function is allowed in HTTP protocol but not in
HTTPS protocol.

Firmware

> Upgrade

1. Click the [Browse] button.

2. Find and open the firmware file.

3. Click the [Upgrade] button to update the firmware.

Note:

When you upgrade the system, it may take some minutes
to be done. Do not close the browser while the upgrade
is in progress. If you close the browser, it may cause a
malfunction. You should wait until the confirmation window
is displayed. When the upgrade is finished, the confirmation
window will be displayed.

> Initialize: The [Initialize] button should be used with caution.

Clicking it will return all of the IP device’s settings to the
factory default values. (Except for the Network settings ­DHCP, IP address, Gateway, Subnet mask, Primary/Secondary
DNS)

28 Operation and settings

Log & Report

Log & Report status

The System log provides a summary of the status of the IP device.
The unit records the data of the software activity in a file.

> View Log: Click this button to display the system log

information.

> View report: Click this button to display the report of the

system.

Language

Audio & Video settings

Camera

Language list

Select a language for the LG Smart Web Viewer configuration menu
and information display.

• Save: Click this button to confirm the settings.

Operation and settings 29

Preview

You can preview the camera image on the preview window.

General

> Contrast: Edit the contrast value from 0 to 100. Selecting 100

provides the image with the highest contrast.

> Standard: Displays the video standard of the camera.

> CaptureMode: Select the capture mode.

Maximum resolution of the camera is 1 280 x 1 024 on 4:3 or
5:4 mode, 1 280 x 720 on 16:9 mode.

Note:

If you change the CaptureMode option, the Privacy, WDR/
BLC and HSBLC settings on the OSD menu are initialized.

• Save: Click this button to confirm the settings.

• Default: Click this button to restore the IP device back to original

factory settings.

Note:

The Capture mode is not initialized.

Stream

Master/Slave

> Enable: Click to activate the stream function.

> Video codec: Select the video mode (Codec) from the drop-

down list. The viewer can choose between MJPEG and H.264.

> Resolution: Select the image size to be sent from the camera.

(1 280x1 024 (4:3 or 5:4), 1 280x720 (16:9), D1(704x480) or
CIF(352x240))

> Maximum frame rate: Set the frame rate of the image.

> GOP size: It means “Group of Pictures”. The higher the GOP,

the better is the video quality of the camera. Edit the value
of GOP from 1 to 30. This setting is valid for H.264 video
format only.

> Quality: Select the Quality.

- VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.

- CBR: The video quality may vary in order to preserve a
constant bit rate.

30 Operation and settings

> Stream quality: If the [Quality] option set to VBR, this option

is displayed. Select the stream quality from the drop down
box, the camera supports five types. (Highest, High, Medium,
Low and Lowest)

> Bit rate: If the [Quality] option set to CBR, this option is

displayed. Edit the bit rate value from 256 kbps to 10 240
kbps.

Note:

If the ‘Bit rate’ is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the ‘Bit rate’ to
high value.

• Save: Click this button to confirm the settings.

Audio

Audio In

> Enable: Click the check box if you want to send the audio

from the microphone input connector.

Note:

The Clients connected to the IP device remain unaffected
with additional changes made in the setting.

> Audio type: Select the codec when you send the audio from

the microphone input connector.

Audio Out

> Enable: Click the check box to output the audio from the

speaker.

• Save: Click this button to confirm the settings.

Operation and settings 31

Motion detect

Preview

You can preview the motion detection window on the preview
window.

General

> Sensitivity: Enter the sensitivity to detect an object in

motion.

> Save: Click this button to confirm the settings.

How to set the motion detect window

1. Click the [Add] button. The motion detect window is
displayed. You can add the five windows maximum for
motion detection area.

2. Set the [Sensitivity] option.

3. Click the edge or corner of the window box to adjust the
window size for motion detection.

4. Click the [Save] button to save the settings.

Note:

• You can reset the window size. Click one of the window edge
or corner and drag & drop to reset the motion detection
area.

• Motion Detection can be activated when at least one of
channels(Master/Slave) is enabled, Video codec is set to
H.264 and GOP size is more than 2.

32 Operation and settings

Network settings

Basic

General

> MAC address: Displays the MAC address.

Port & Encryption

> Web port: The default HTTP port number (80) can be changed

to any port within the range 1 025 to 65 535.

> RTSP port: Check RTSP port. The default port is 554. Other

ports can be selected within the range 1 025 to 65 535.

> Network encryption: Select the HTTP or HTTPS option for

security.

Note:

The RTSP port number should not be same with the web
port number.

ARP Ping

> Enable ARP Ping to configure IP address: Check to enable

ARP ping.

• Save: Click this button to confirm the settings.

RTP stream

RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data,
via unicast or multicast.

Master / Slave

> RTP unicast: When enabled the transmission of the data to

the specified equipment happens on a network specifying a
single address.

Operation and settings 33

> RTP multicast: When enabled it reduces the transmission

load on the camera by making the computer of the same
segment network receive the same transmission data. When
multicast option is checked then select Video Port number,
Audio Port number and Data port number.

- Video RTP port: Specify the video transmission port
number used for the multicast streaming. It is initially set
to 8 888 and you can edit this between 1 025 and 65 534.

- Audio RTP port: Specify the audio port number used for
the multicast streaming. It is initially set to 7 778 and you
can edit this between 1 025 and 65 534.

- Data RTP port: Specify the VA data port number used for
the multicast streaming. It is initially set to 6 666 and you
can edit this between 1 025 and 65 534.

- IP address: Set the IP address for RTP multicast.

Note:

Each stream using multicast needs its own pair of multicast
IP address and port numbers to avoid address conflict.

TTL

> TTL: This option indicates the Time-To-Live of multicast

packets. The default setting is 7, and the allowed TTL range is
from 1 to 255.

• Save: Click this button to confirm the settings.

TCP/IP

IP address status

> Automatically set with DHCP: Select this option when a

DHCP server is installed on the network to allow IP address
assignment. With this setting, the IP address is assigned
automatically.

- Notify to SMTP server, if IP address is changed: If you
select this option, the user get a notification mail telling
about changing of IP of the IP device.

Note:

You should register the SMTP server on the Event server set­ting to set this function.

> Statically set: Select this option when you set a fixed IP

address, with this setting, specify the IP address, Subnet
mask and default gateway manually.

- IP address: Enter an IP address.

- Subnet mask: Enter a subnet mask address.

- Gateway: Enter the gateway address.

34 Operation and settings

DNS server status

> Primary DNS server: Enter the Primary domain name server

that translates the hostnames into IP address.

> Secondary DNS server: Enter the Secondary DNS server

address that backups the Primary DNS.

• Save: Click this button to confirm the settings.

DDNS

This free service is very useful when combined with the LG DDNS
Server. It allows the user to connect the IP device using the URL,
rather than an IP Address. This also solves the problem of having a
dynamic IP address.

DDNS status

> Don’t use DDNS server: Disable the DDNS function.

> Use DDNS server: Enable the DDNS function.

- Provider: Displays the DDNS provider.

- Hostname: Enter the hostname you want to use.

• Save: Click this button to confirm the settings.

Operation and settings 35

IP filtering

The access of the IP addresses in the list are allowed or denied
according to the choice made in the drop-down list of the Basic
policy option. The administrator can add up to 10 IP address entries
to the list (a single entry can contain multiple IP addresses). The
users from these IP addresses need to be specified in the user list
with the appropriate access rights. The IP list is to control the access
permission of clients by checking the client IP address.

IP list

> Basic policy: Select the basic policy type.

- Allow all: Allow all the IP address basically, but the IP
addresses in the list are denied.

- Deny all: Deny all the IP address basically, but the IP
addresses in the list are allowed. It needs at least one IP
address to activate this function.

• Save: Click this button to confirm the settings.

• Add: Click this button to add the IP address.

1. Click the [Add] button.

2. Set the IP options.

- Alias: Enter the alias.

- From: Enter the start IP address for the IP filtering.

- To: Enter the end IP address for the IP filtering.

Note:

If you want to deny or to allow a range of IP addresses, enter
the start IP address to “From” and the end IP address to “To”.
You can also add an IP address by entering the same IP
address to “From” and “To”.

3. Click the [Save] button.

4. Repeat the steps 1 to 3 to add additional IP address.

• Remove: Click this button to delete the IP address.

1. Select the alias from the list.

2. Click the [Remove] button. The IP address will be deleted.

36 Operation and settings

User settings

Basic

The IP device is shipped with the login rights of administrator only.
If others need to access the IP device excluding the configuration a
login with viewer rights need to be created. A maximum of 50 users
can be created.

User list

> Add the User

You can register a new user with various access rights.

1. Click the [Add] button. User setting dialog is displayed.

2. Enter the new User ID and Password. (Should have a
minimum of 4 characters and preferably a combination
of alphanumeric.)

3. To confirm the password, retype the password that you
typed in the Password box.

4. Select the authority from the drop down list to provide
the access rights to each user and then click the [Save] to
confirm your selection.

- Administrator: Allows you to operate setup menus
and to view live images.

- Power user: Use of the limited functions of the
system. (The Configuration menu is not allowed.)
A power user can use the Live View, OSD control and
audio functions.

- Normal user: Provides the lowest level of access,
Allows to view live images only.

- Custom user: The user can login and view the live
stream image only when the “Enable anonymous
login” option is checked to enable it.

Note:

Remember the password.

> Edit the registered user

You can change the password or authority.

1. Choose the user ID and then click the [Edit] button.

2. Change the Password or Authority, then click the [Save]
button to confirm your selection.

> Delete the registered user

1. Choose the user ID you want to delete.

2. Click the [Remove] button.

Note:

The default administrator user ID ‘admin’ and ‘anonymous’
are permanent and cannot be deleted.

Operation and settings 37

Anonymous

> Enable anonymous login

Check the box to enable anonymous user login - allows the
user access for only viewing the live stream image.

Maximum RTP stream connection

> Maximum number of simultaneous stream connection:

Set this number to limit the number of simultaneous stream
connections.

The connections depend on the stream configuration as
shown in the following Maximum RTP stream connection by
stream configuration.

Video Codec Resolution

H.264 720p 30 HIGHEST Up to 10

MJPEG 720p 20 HIGHEST Up to 7

Note:

Preview window of the IP device setting and preset setting
are affected by this setting.

• Save: Click this button to confirm the settings.

Frame

Rate

Quality

SD Card settings

Basic

Maximum

RTP

stream

SD Card Recording

> Always: Start the recording at once.

> Recurrence Pattern: The recording is started according to the

setting time of the selected day.

Note:

You can not set the time for a day. It will start the recording
for the selected day of the time.

> Never: [Always] and [Recurrence Pattern] recording functions

are not activated.

38 Operation and settings

> Overwrite: If the micro SD card has insufficient space and

this option will be activated. It will overwrite the oldest data.

> DiskFull Notification: Sends an warning e-mail to the SMTP

server when the micro SD card has fully recorded. Select the
SMTP server from the drop-down list. You should register the
SMTP server on the Event server setting to set this function.

> Network Failure Recording: Select the checkbox to activate

the micro SD card recording function. If the system does
not work with recording server, the system will record the
data to the micro SD Card. When the system connect to the
recording server again, the recorded data of the micro SD
card will transfer to the recording server automatically.

> Recording Server IP: Enter the rcording server IP.

> Set as NTP server IP: Click this button to use the entered

Recording Server IP as the NTP server IP.

> Stream: Select the stream type for the recording.

Notes:

The recorded file name is made automatically as the
“[Created date of the file]_[GMT Recording Time]+(-)[Value
of the Local Time minus GMT Time (Second)]_[Use or not of
the Daylight saving time(N/D)][Stream index][DeleteFlag].
DAT” type.

Disk Management

> Using the micro SD card

1. Insert the micro SD card carefully to the micro SD card
slot of the camera.

2. Click the [Mount] button. If the micro SD card is mount­ed to the system correctly, the [Mount] button will be
changed to the [Unmount] button.

3. Displays the information of the [Disk ID], [Status], [Total
Space] and [Free Space] options.

Notes:

• When the micro SD card is mounted, you should format
the micro SD card. After the micro SD card format is fin­ished, you should click the [Mount] button to use it.

• When you use the micro SD card format function, it may
not progress immediately. In this case, you should try it
again after waiting a few minitues.

> Remove the micro SD card

1. Click the [Unmount] button. If the micro SD card is
unmounted from the system correctly, the [Unmount]
button will be changed to the [Mount] button.

2. Remove the micro SD card from the micro SD card slot of
the camera.

Note:

When you use the Unmount function, it may not progress
immediately. Operations such as recording of the system and
reading of data are required stop time before the Unmount
function is activated. You should try it again after waiting a
few minitues.

Operation and settings 39

File Management

Displays the recorded file of the micro SD card on the list. Click the
[Search] button to display the recorded file. The list will be updated
when you click the [Search] button.

> To view the recorded file of the micro SD card

1. Select the search option.

- All: Search the all recorded files in the micro SD card.

- Some: You can set the search condition by using the
date and time options.

2. Click the [Search] button and then the search result is
displayed on the list.

> Download: You can download the recorded data of the list

to your PC. Select a recorded file on the list and click the
[Download] button. The two confirmation window is dis­played. You should download the all files that the recorded
file(*.DAT) and information file(*.INFO).

Notes:

• It is recommended to deactivate the [Overwrite] function
before you download the file. When [Overwrite] function
is activated, the downloading file might be overwritten,
if the micro SD card has insufficient space.

• The downloaded file can be played by using the LG
Smart Station player.

> Remove: Delete file from the SD card.

Event settings

Event schedule

When an event (VA/ Motion detect/ Sensor Event) occurs, this unit
records the live images and routes as configured.

Event schedule list

> To edit the Event Schedule

1. Select the Trigger event and click the [Edit] button.
Event schedule window is displayed.

2. Set the options.

• Trigger: Displays the selected trigger event.

• Time: Sets the weekday, Start, Finish, Pre alarm, Post

alarm and Ignore interval time options.

• Action: Selects the options. This occurs when the

event runs.

- FTP server/SMTP server: Uploading of images to
an FTP server, or e-mail notification.

- Control relay: The relay is activated or
deactivated.

- SDCard recording: Record on the SD card when
the event runs.

40 Operation and settings

• Stream: Selects the stream of the connected camera.

• Default: Sets to default setting value.

3. Click the [Save] button to confirm the settings.

Note:

• You should register the SMTP and FTP server on the
Event server setting to set this function.

• Recording of event(VA/Modtion detect/Sensor event)
runs every 5 minutes split file.

• If the capacity of the SD card remains less than 200 MB,
stop recording or overwrite new file after delete old one
as [Overwrite] setting. The overwritten file can not play
or may malfuction when you download.

• Recorded file on the SD card, is recording 1 frame per
second when set video codec to MJPEG.

Event Server

Event Servers are used to receive the recorded video clip and/or
notification messages.

FTP server list

Image files can be transferred to the FTP server within the scheduled
time. Image file that has been recorded linked to an external event
is sent to the FTP server periodically.

> To add the FTP server

1. Click the [Add] button. FTP server setting window is
displayed.

2. Set the FTP server options.

- Alias: Type the FTP Server name to upload the image
files.

- Address: Enter the FTP server’s IP address.

- Port: Enter the port number. The default FTP port is

21.

- User ID: Type the user name for the Folder shared in
the FTP server.

Operation and settings 41

- Password: Type the password for the folder shared in
the FTP Server.

- Folder: Type the path with the folder that is shared in
the FTP server.

- Test: Select [Test] to test the FTP server.

3. Click the [Save] button to confirm the settings.

> To edit the FTP server

1. Choose the FTP server in the FTP server list.

2. Click the [Edit] button.
You can check or edit the FTP server options.

> To delete the FTP server

1. Choose the FTP server in the FTP server list.

2. Click the [Remove] button. This would remove the FTP
server from the list.

SMTP server list

By selecting the e-mail option, a still image of the event is captured
and an e-mail with the attached image file is sent to the specified
mail address.

> To add the SMTP server

1. Click the [Add] button. SMTP server setting window is
displayed.

2. Set the SMTP server options.

- Alias: Enter the SMTP server name.

- User ID: Enter the user ID of the SMTP server. This
would be the one who owns the mail account.

- Password: Enter the password of the SMTP server.

- Address: Enter the SMTP server address.

- Port: Enter the port number. The default port is 25.

- Enable SSL: Check when use the SSL (Secure Socket
Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a
network.

- Receiving address: Type the recipients e-mail address.
You can specify only one recipient e-mail address.

- Administrator address: Type the e-mail address of the
administrator.

- Subject: Enter the subject/title of the e-mail.

- Message: This message can describe the information
of the acquired IP address, etc.

- Test: Select [Test] to test the SMTP server.

3. Click the [Save] button to confirm the settings.

> To edit the SMTP server

1. Choose the SMTP server in the SMTP server list.

2. Click the [Edit] button.
You can check or edit the SMTP server options.

> To delete the SMTP server

1. Choose the SMTP server in the SMTP server list.

2. Click the [Remove] button.

42 Operation and settings

Sensor & Relay

Sensor

> Enable: Marks up when you want to activate the sensor.

> Alias: Displays the sensor name.

> Type: Select the sensor type.

Relay

> Control duration: Enter the relay time.

> Alias: Displays the relay name.

> Type: Select the relay type.

> Control relay

- Run: Click to activate the relay.

- Stop: Click to stop the relay.

• Save: Click this button to confirm the settings.

OSD Menu Setup

The following table shows the list of menu items and options.
You can adapt the camera to your requirements by setting up the
respective items in these menus.

Main Menu Sub Menu Contents

OFF/WDR/BLC/

HSBLC

OFF/LOW/MIDDLE/

HIGH

X64, ..., x2, AUTO,

OFF, A.FLK, 1/100,

..., 1/10 000

OFF

AUTO

INDOOR,

OUTDOOR

EXPOSURE ELC/ALC

ATW -

AUTO

AWC / PUSH -

WHITE BAL

MANUAL

WDR/BLC

BRIGHTNESS 0 to 100

AGC

SHUTTER

SENS-UP

EXIT RET/TOP/END

COLOR TEMP

RED -100 to 100

BLUE -100 to 100

EXIT RET/TOP/END

Operation and settings 43

DAY/NIGHT

3D-DNR

PRIVACY

LEVEL LOW/ MIDDLE/ HIGH

AUTO

DAY -

NIGHT -

OFF -

LOW -

MIDDLE -

HIGH -

OFF -

ON

DWELL TIME 5, 10, 15s

EXIT RET/TOP/END

COLOR

TRANSPARENCY 0 to 16 -

RECTANGLE

RED 0 to 255

GREEN 0 to 255

BLUE 0 to 255

EXIT

MASK

NUMBER

RECT.

DISPLAY

HEIGHT 4 to 100

WIDTH 4 to 100

MOVE Y 2 to 98

MOVE X 2 to 98

EXIT

RET/TOP/

END

AREA1 to

AREA8

ON/OFF

RET/TOP/

END

PRIVACY ON

BACK FOCUS

FOCUS RESET -

NUMBER

CIR. DISPLAY ON/OFF

HEIGHT 1 to 15

CIRCLE

POLYGON

EXIT RET/TOP/END

MANUAL

ADJUST

ABF PUSH -

D/N ABF OFF/ON

EXIT RET/TOP/END

MOVE Y 0 to 100
MOVE X 0 to 100

RADIUS SIZE 0 to 100

NUMBER

DISPLAY

POLYGON

POLYGON

-

MASK

WIDTH 1 to 15

EXIT

MASK

POLY.

DRAW

MOVE

EXIT

AREA1 to

AREA2

RET/TOP/

END

AREA1 to

AREA2

ON/OFF

-

-

RET/TOP/

END

44 Operation and settings

SPECIAL

SCENE MODE

OFF

ZOOM

D-ZOOM

D-EFFECT OFF/ V-FLIP/ MIRROR/ ROTATE

SHARPNESS 0 to 68

COLOR OFF/ ON

PIP

STABILIZER OFF/ ON

USER TITLE OFF/ ON

LANGUAGE

EXIT RET/TOP/END

STD

BKLT

LOWLIT

OUTDOOR

INDOOR

TRAFFIC

USER

ON

OFF

ON

English

(The option depends on the model.)

PAN

TILT

EXIT

WINDOW MOVE

IMAGE MOVE

IMG SIZE

EXIT

CAMERA

RESET

EXIT - -

REBOOT

FACTORY RESET -

EXIT -

-

Operation and settings 45

General Operation

1. Click the [OSD control] button on the LG Smart Web Viewer.

2. Click button on the OSD control window.
The camera setting menu appears on the live view window.

3. Use or button to select an option then click button.
Submenu appears.

4. Use or button to select a submenu option.

5. Use or button to select a value.

6. Select [EXIT] option then click button to exit the setup menu.
In the submenu, use or button to select the [EXIT ] then use

or button to select a mode and click button to exit the

setup menu.

- RET: Return to the previous.

- TOP: Return to the CAMERA SETTING menu screen.

- END: Exit the setup menu.

Notes:

• button: Used to move upper direction on the menu screen.

• button: Used to move lower direction on the menu screen.

• button: Used to increase the value selected in the menu.

• button: Used to decrease the value selected in the menu.

• button: Executes selections and displays a submenu for an

item with the mark.

46 Operation and settings

Exposure settings

You can set the exposure options using the EXPOSURE menu.

1. Select [EXPOSURE] option on the [CAMERA SETTING] menu.

2. Use or button to select a mode (ALC ELC).

3. Press button and the EXPOSURE menu appears.

Notes:

• ELC Mode is right for outdoor scenes.

• ALC Mode is right for indoor scenes.

WDR/BLC

Use WDR/BLC option to view the object clearly in backlight
conditions.

1. Select [WDR/BLC] option on the [EXPOSURE] menu.

2. Use or button to select a mode then click button.

• WDR: WDR (Wide dynamic range) feature can be very
helpful to cope with very challenging lighting condi­tions. It is capable of capturing both of the dark part and
bright part and combining the differences into a scene
to generate a highly realistic image as original scene. Set
the WDR limit.

> WDR LIMIT: LOW MIDDLE HIGH

> ACE (Adaptive Contrast Enhancement) : This function

is used when you want to display dark areas of WDR
brightly.

• BLC: Camera’s backlight compensation feature helps
alleviate issues of visibility in high contrast areas. Set the
BLC limit.

> BLC LIMIT: LOW MIDDLE HIGH

• HSBLC: Use for masking brightness of the specific area
to view the subject more clearly. The HSBLC mode is
automatically activated only in low luminance scene.

> AREA SETTING: Use or button to select area

then use or button to select [ON] or [OFF]. Click

button to exit the area setting menu.

> GRAY SCALE: Use or button to select a gray

scale.
(GRAY D.GRAY BLACK)

> USER SCALE: Use or button to select a bright

level. (5 levels)

> MASK: Use or button to select [ON] or [OFF].

If you set the MASK to ON, the mask function is
activated only when the HSBLC is activated by auto
mode.

• OFF: Not in use.

BRIGHTNESS

You can increase the brightness of the darkened video. If you set the
brightness to lower value, the image gets darkened. If you set the
brightness to higher value, the image gets bright.

1. Select [BRIGHTNESS] option on the [EXPOSURE] menu.

2. Use or button to set the bright level.

Operation and settings 47

AGC (Automatic Gain Control)

If the images are too dark, change the maximum [AGC] value to
make the images brighter.

1. Select the [AGC] option on the [EXPOSURE] menu.

2. Use or button to select a mode.

SHUTTER (Shutter Speed)

Select the desired shutter speed for camera exposure. You can
change the shutter speed to higher speed to capture fast-moving
subjects, though the image becomes darker.

1. Select [SHUTTER] option on the [EXPOSURE] menu.

2. Use or button to set shutter speed.

SENS-UP

If pictures are not clear due to darkness, this SENS-UP operation
would increase the sensitivity of picture.

1. Select [SENS-UP] option on the [EXPOSURE] menu.

2. Use or button to select a mode.

• AUTO: Adjust the sensitivity of the picture automatically.

> SENS-UP LIMIT: Use or button to set the

SENS-UP limit. (x2 to x64)

> EXIT: Select a mode and click button to exit the

menu.

Note:

If you set to one of the SHUTTER options except AUTO on the
[SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not
available and [---] mark is displayed.

White Balance settings

Select the method by which the camera shifts its output colors to
compensate for the color of a light source.

1. Select the [WHITE BALANCE] option.

2. Use or button to select a mode then click button.

• ATW (Auto-Tracing White Balance): In this mode, white
balance has better coverage than auto. Proper white balance
may not be obtained under the following conditions:

> When the scene contains mostly high color temperature

objects, such as a blue sky or sunset.

> When the scene is dim.

• AUTO: You can set the white balance options automatically.

• AWC / PUSH: If you select the AWC / PUSH mode, you will

be able to set up the White Balance automatically using
button.

• MANUAL: You can set the white balance options manually.

> COLOR TEMP: Use or button to select a function.

48 Operation and settings

- INDOOR: The color temperature range for the proper
white balance is approximately 3 200 K.

- OUTDOOR: The color temperature range for the
proper white balance is approximately 5 100 K.

> RED: Set the desired red value.

> BLUE: Set the desired blue value.

Day/Night settings

1. Select [DAY/NIGHT] option.

2. Use or button to select a mode for DAY/NIGHT function.

• AUTO: DAY/NIGHT mode changes automatically.

Note:

If you set the AGC to [OFF] on the [EXPOSURE] menu, the
AUTO mode of the DAY/NIGHT function is not available and
[---] mark is displayed.

> LEVEL: Use or button to select a level.

> DWELL TIME: Use or button to select a dwell time.

• DAY: Color mode enabled.

• NIGHT: Black-and-white mode enabled.

Operation and settings 49

3D-DNR setting

1. Select [3D-DNR] option.

If pictures are not clear due to noise, this option would reduce
the noise of picture.

2. Use or button to select an option.

Notes:

• If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark is displayed.

• When you use this function, the afterimage may occur.

Privacy setting

This function is aiming at the protection of personal privacy. The
selected part is not displayed on the screen.

1. Select the [PRIVACY] option.

2. Use or button to select [ON] and press . The PRIVACY
SETUP menu appears.

• COLOR : You can make any color by adjusting R.G.B LEVEL.

• TRANSPARENCY : You can adjust the transparency of MASK.

• RECTANGLE :

> Use or button to select a mask on the [MASK

NUMBER].

> Use or button to set up the [ON] or [OFF] on the

RECT. DISPLAY option.

> Use or to select an option then use or button

to adjust the option.

- HEIGHT: Increase or decrease the vertical size of the
mask.

- WIDTH: Increase or decrease the horizontal size of
the mask.

- MOVE Y: Moves vertical position of the mask.

50 Operation and settings

- MOVE X: Moves horizontal position of the mask.

• CIRCLE :

> Use or button to select a mask on the [MASK

NUMBER].

> Use or button to set up the [ON] or [OFF] on the

CIR. DISPLAY option.

> Use or to select an option then use or button

to adjust the option.

- HEIGHT: Increase or decrease the vertical size of the
mask.

- WIDTH: Increase or decrease the horizontal size of
the mask.

- MOVE Y: Moves vertical position of the mask.

- MOVE X: Moves horizontal position of the mask.

- RADIUS SIZE : You can adjust the RADIUS SIZE.

• POLYGON :

> Use or button to select a mask on the [MASK

NUMBER].

> Use or button to set up the [ON] or [OFF] on the

POLY. DISPLAY option.

> Use the , , , and buttons to draw the polygon

by moving each vertex on the [POLYGON DRAW]. Each
movable vertex will be displayed as a black square spot
each time you click the button.

> Use the , , , and buttons to move the

polygon on the [POLYGON MOVE].

Back Focus Setting

The back focus function is activated automatically according to your
setting. And also, when the Day&Night function is activated, the
Back Focus function is activated automatically.

MANUAL ADJUST

You can adjust the back focus manually.

1. Select the [MANUAL ADJUST] option on the [BACK FOCUS]
menu and then click button.

2. Use or button to adjust the focus point then click
button to exit the menu.

ABF ADJUST

You can adjust the back focus automatically.

1. Select the [ABF ADJUST ] option on the [BACK FOCUS] menu and
then click button. This function will be activated automatically
to adjust the back focus.

2. When the focus setting is finished, click button to return to
the previous menu.

Operation and settings 51

FOCUS RESET

Reset the focus point to factory default position.

Select the [FOCUS RESET] option on the [BACK FOCUS] menu and
then click button. The screen will be dim.
Use the [Manual Adjust] or [ABF push] option to adjust the focus.

Note:

You can reset the focus using the ABF button. When you keep
pressing ABF button about 4 seconds, the camera will reset the
focus.

D/N ABF

You can set the Day&Night function with ABF function.

Use or button to select a option.

• ON: If you set to On, the ABF function will be activated
automatically when the D/N function is activated.

• OFF: Not used.

Special menu settings

D-ZOOM

You can select the digital zoom level.

1. Select [D-ZOOM] option on the [SPECIAL] menu.

2. Use or button to select [ON] then click button. When
you set to ON, the displayed image can be shaking.

3. Use or button to select an option then use or
button to select a level.

• ZOOM: Use or button to enlarge the screen.

• PAN: Use or button to move the screen. (left or

right)

• TILT: Use or button to move the screen. (up or

down)

D-EFFECT (Digital effect)

You can select the digital effect.

1. Select the [D-EFFECT] option on the [SPECIAL] menu.

2. Use or button to select a digital effect.

• V-FLIP: Flip the picture vertically.

• MIRROR: Turn on the mirror effect.

• ROTATE: Rotate the picture. (180°)

52 Operation and settings

• OFF: Turn off the digital effect.

SHARPNESS

The degree to which the boundary of the two portions is clearly
distinguished.

1. Select the [SHARPNESS] option on the [SPECIAL] menu.

2. Use or button to adjust the option. If you set the
sharpness value to higher, the image outline becomes sharp.
If you set to lower value, the image outline becomes dim.

COLOR

You can switch the displayed picture to gray scale or color.

1. Select the [COLOR] option on the [SPECIAL] menu.

2. Use or button to change a color effect.

• ON: To display the picture with color.

• OFF: To display the picture with grayscale.

PIP

You can view an image in PIP(picture in picture) mode.

1. Select the [PIP] option on the [SPECIAL] menu.

2. Use or button to select [ON] then click button. The PIP
window is displayed on the live window.

• WINDOW MOVE : The PIP window can be moved through the

live image window using , , and buttons.

• IMAGE MOVE : You can view the special area image on the

PIP window. Use , , or button to view the live
image of the special area.

• IMG SIZE: Use or button to enlarge or reduce the size

of image on the PIP window. This function is activated with
digital zoom function.

STABILIZER

The image stabilizer function minimizes the appearance of shaky
images caused by low-frequency vibration.

This function is useful for outdoor surveillance.

Select the [STABILIZER] option and set to ON or OFF.

Note:

If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1]
automatically.

USER TITLE

You can use the camera identification to assign a number and
character to the camera (0 to 9, A to Z, a to z).
To disappear the user title, select [OFF].

1. Select the [USER TITLE] option on the [SPECIAL] screen.

2. Use or button to select [ON] then click button. The
USER TITLE menu appears.

A

3. Use , , or button to select a character or number
then click button.

• CLR: Clear all entered characters and numbers.

• POS: Move the USER TITLE position on the screen using

the arrow buttons.

• END: Confirm your selection or exit the setting.

Operation and settings 53

• A(Blank): Insert a space at the cursor position.

• / : Moves cursor to left or right.

LANGUAGE

Select the viewer language for the camera setup menu and OSD
information display.

1. Select the [LANGUAGE] option on the [SPECIAL] screen.

2. Use or button to select the language.

SCENE mode setting

You can set value installed camera environment properly using this
function. Several configuration value is set automatically to select
option.

• STD: Settings general environment .

• BKLT: WDR set automatically to see the subject clearly under the

backlight condition.

• LOWLIT: Increase the Gain and set SENS-UP function to see the
subject cleary under the low light condition.

• OUTDOOR: Change to the ELC mode not to decrease definition
under too light condition. And decrease Brightness valuse
slightly prevent to video of supersaturation.

• INDOOR: Condition of light set automatically to match indoor
environment.

• TRAFFIC: Set shutter speed fast to apprehend traffic information
and status.

• USER: If user change each value of function, save the changes.

Notes:

Set each value of option as selected option on the [SCENE MODE]
like as below table.

OPTION STD BKLT LOWLIT OUTDOOR

Shutter

speed

AGC MIDDLE MIDDLE HIGH MIDDLE

White

Balance

WDR/BLC OFF WDR OFF OFF

3D-DNR MIDDLE MIDDLE MIDDLE MIDDLE

DAY/NIGHT AUTO AUTO AUTO AUTO

ACE - OFF - -

SHARPNESS 34 34 34 34

BRIGHTNESS 50 50 50 45

SENS-UP OFF OFF AUTO x10 OFF

EXPOSURE ALC ALC ALC ELC

AUTO AUTO AUTO AUTO

ATW ATW ATW ATW

54 Operation and settings

OPTION INDOOR TRAFFIC USER

Shutter speed AUTO Manual(1/120) -

AGC MIDDLE HIGH -

White Balance

WDR/BLC OFF OFF -

3D-DNR MIDDLE MIDDLE -

DAY/NIGHT AUTO AUTO -

ACE - - -

SHARPNESS 34 34 -

BRIGHTNESS 50 50 -

SENS-UP OFF OFF -

EXPOSURE ALC ALC -

• Value of [SCENE MODE] is not initialized even the reboot system.
If you set to [STD], the defaut value of [SCENE MODE], run
factory reset.

• If you use not DC Iris lens but Manual Iris lens, must set ELC
mode on the [EXPOSURE] option. In this case, value of [SCENE
MODE] set to [USER] automatically.

Manual

(Indoor)

ATW -

Reset setting

1. Select the [RESET] option.

2. Click button and the RESET menu appears.

3. Use or button to select option.

• CAMERA REBOOT: Reboot the camera system.

• FACTORY RESET: Clear certain settings and information and

return to factory default settings.

4. Click button to confirm your selection.

Operation and settings 55

Reference

Troubleshooting

This section provides useful information to help you to resolve any difficulty you might have with your LG IP device. Fault symptoms,
possible causes and remedial actions are provided here.

IP Setting problems

• ARP/Ping: Disconnect and reconnect the power to the network camera. The device should get the IP within 2 minutes.

• Ping your camera: Open the command prompt on your computer, type ping with the IP address of the network device. The reply

obtained by this command provides explanation for the cause of the problem.

1. bytes = 32 time = 2 ms indicates that the IP address is already used and cannot reuse the same. A new IP address needs to be
obtained.

2. Destination host unreachable: indicates that the network device and your computer do not fall in the same subnet hence needs to
get a new IP address. Contact the system administrator for the required help.

3. Request timed out: Indicates that the IP is free as it is not used by anyone and the network device can obtain this.

• IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the
network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.

Cannot access the camera from browser:

• Reconnect the network camera with power and check the ping operation to know if the IP is used by others.

• Disable the proxy setting in the Browser if you are using a proxy server.

• Check for proper cabling and network connections, try to ping after verifying the connectivity.

• Sometimes when HTTPS is enabled, we would be checking the URL with http, in this case manually change the URL to the http/https

accordingly.

• Verify the DNS and Gateway settings if the IP address is assigned statically to the network device.

56 Reference

Accessing camera external to the local network

• Firewall Protection: Check for the internet firewall with the system administrator, either he has to do port forwarding or modify the DMZ
function on the router.

• Default router needed: Check if you need configure the router settings.

Sporadic network performance

• Network Switches or hubs used may be of the lower configuration and the load on this may not meet the required conditions of our
network camera.

• Check for the RJ-45 cables that are used for the network connectivity.

• If POE is used check if the power is got by the network camera when connected to it.

Login Password lost

• Reset the camera by pressing the Reset button for more than 3 seconds to restore default settings.

• After the factory settings login using the default user name and password.

Video Streaming problems

• If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the
instructions on the Web browser.

• When Windows IE browsers are used always take care to allow pop ups, check this option before we run the web client.

• Check the quality of image by referring the video settings as described in the manual.

• Sometimes there would be intermittent or very slow video streaming, this may be because of the higher resolution and frame rate that

are set for the video.

• The video streaming may appear poor at times, this may be because of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and because of other programs running on your computer.

• If the images appear to be blurred adjust the focus of the network camera to get a clear image.

• Video images if appear white and black adjust the settings in the OSD to get back the colorful image.

• Select the Night mode if the network camera is connected at a place where surrounding light is less or dark.

Reference 57

• If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.

• If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.

• If the images appear to have white of gray stripes on it, upgrade the Video graphics driver on the client PC to the latest version.

• Video images may be noisy if you are using the camera in a very low light environment or the bit rate/quality is set to very low values.

Provide higher values for quality and support the surrounding environment with enough light.

Audio condition

The client computer that is interacting with the camera needs to have a sound card that is functional to support speaker and microphone.

The sound card needs to be checked for its support for full duplex communication.

Ensure that the mute button of the client computer is not set and all the audio settings are correct.

Speaker button on the web viewer should be enabled to listen the audio from the network camera.

Ensure that the bidirectional audio button is enabled on the Web viewer and the microphone is set.

Change the input and the output gain for microphone and the speaker respectively to set correct audio level.

For all further support please contact the supplier or forums or websites.

58 Reference

Open source software notice

The following GPL executables and LGPL libraries used in this product are subject to the GPL2.0/LGPL2.1 License Agreements:

GPL EXECUTABLES:

Linux kernel 2.6, bash, busybox, gdbm, libreadline, module-init-tools, mount, mtd-utils, net-tools, quftp, tar, util-linux

LGPL LIBRARIES:

Glibc, libelf, libesmtp, live.media

LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing such distribution, such as the
cost of media, shipping and handling upon e-mail request to LG Electronics at:

[e-mail]

This offer is valid for a period of three (3) years from the date of the distribution of this product by LG Electronics.

You can obtain a copy of the GPL, LGPL licenses from http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and http://www.gnu.org/
licenses/old-licenses/lgpl-2.1.html.

This product includes mDNSResponder component which is licensed under the terms of the Apache License, Version 2.0.

You can obtain a copy of the Apache license from http://www.apache.org/licenses/LICENSE-2.0.html.

Reference 59

This product includes

• dhcp client :

Copyright © 2004-2008 by Internet Systems Consortium, Inc. (“ISC”)

Copyright © 1995-2003 by Internet Software Consortium

• expat library : copyright © 2006 expat maintainers.

• libcap

• libjpeg : Independent JPEG Group Copyright © 1991 1998, Thomas G. Lane.

• libmd5 : Copyright © 2002 Aladdin Enterprises.

• libncurses : Copyright © 1998,2002 Free Software Foundation, Inc.

• libpcre : Copyright © 1997-2009 University of Cambridge

• libxml2 : Copyright © 1998-2003 Daniel Veillard.

• lighttpd : Copyright © 2004, Jan Kneschke, incremental

• ntpdate : Copyright © David L. Mills 1992-2006

• OpenSSL :

> cryptographic software written by Eric Young ([e-mail]).

> software written by Tim Hudson ([e-mail]).

> software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)

• PHP software, freely available from http://www.php.net/software/ : Copyright © 1999 - 2009 The PHP Group.

• Speex :

> Copyright 2002-2008 Xiph.org Foundation

> Copyright 2002-2008 Jean-Marc Valin

> Copyright 2005-2007 Analog Devices Inc.

> Copyright 2005-2008 Commonwealth Scientific and Industrial Research Organisation (CSIRO)

> Copyright 1993, 2002, 2006 David Rowe

> Copyright 2003 EpicGames

> Copyright 1992-1994 Jutta Degener, Carsten Bormann

• Zlib : Copyright © 1995-2002 Jean-loup Gailly and Mark Adler.

60 Reference

All rights reserved.

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the
“Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the
following conditions:

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Reference 61

Specications

ITEM LW6324 Series LW6354 Series

Camera Image Sensor 6.08 mm Progressive Scan CMOS (1.3 Mega Pixels)

Lens F1.2 Varifocal Lens (2.8 mm to 10 mm)

Illumination

Resolution Up to 1 280 x 1 024

Day/Night ICR

WDR Support

Image Enhancement Backlight Compensation, 3D-DNR, Exposure Control, Sens Up Control, AGC, White Balance,

Video Video Out 1 RCA Output

Compression H.264, MJPEG

Frame Rate 30 fps @ 1 280 x 1 024 (mode 4:3), 1 280 x 720 (mode 16:9)

Multi-Streaming Dual Streaming

Audio Audio In/Out 1/1

Compression G.711, G.726

2-way Audio Support

Event Alarm In/Out 1/1

Motion Detection Support

Event Notification Relay Out, Email, FTP

Pre Event Buffering Support

Color 0.3 lx (F1.2, Gain : High)

B/W 0.005 lx (F1.2, Gain : High)

Privacy Masking, EIS, Sharpness, Digital Zoom

62 Reference

Video Analytics Intruder Detection Not support Support

Crossing Line Not support Support

Object Removal Not support Support

Object Counting Not support Support

Tampering Not support Support

Network Ethernet 10/100 Ethernet

Security Password Protection, HTTPS(SSL, TLS)

Protocol TCP/IP(IPv4), HTTP, HTTPS, RTP, RTSP, UDP, DHCP, FTP, SMTP, NTP, ARP, ICMP, DDNS(LG)

Management Integrated Client LG Smart Station (64ch recording and monitoring feature)

Simple Web Client Live monitoring and system management for a device

System Update LG Smart Station or Web Client

Connections Up to 10

Misc. Power Source PoE (IEEE 802.3af ), DC 12 V (±20%)

Power consumption 6.2 W 7 W

Input current DC 12 V : Maximum 480 mA

PoE : Maximum 170 mA

Operating Temperature

Operating Humidity

Weight

Dimension (ø x H)

-10 °C to 50 °C

0 % RH to 80 % RH

1.4 kg

200 mm x 141 mm

DC 12 V : Maximum 550 mA
PoE : Maximum 200 mA

Reference 63