LG LVC-SX701OC Owner’s Manual

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 1

Color Video Camera

Instruction Manual

Models : LVC-SX701PC/OC/MC

Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Regulatory Notices For U.S.A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

2

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

•Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

•Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 3

Important Safety Instructions

1.Read these instructions. - All these safety and operating instructions should be read before the product is operated.

2.Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3.Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4.Follow all instructions. - All operating and use instructions should be followed.

5.Do not use this apparatus near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc.

6.Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

3

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 4

Important Safety Instructions

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/ accessories specified by

the manufacturer.

12.Use only the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 5

Contents and Features

Contents
Important Safety Instructions . . . . . . . . . .	. .3-4
Contents and Features . . . . . . . . . . . . . . .	. . .5
Features Chart . . . . . . . . . . . . . . . . . . . .	. . .6
Cautions for Safe Operation . . . . . . . . . . . .	. . .7
Part Names and Functions . . . . . . . . . . . . .	.8-10
Connections . . . . . . . . . . . . . . . . . . . . . .	. .11
Mounting the Lens . . . . . . . . . . . . . . . . . .	. .12
Concerning Auto-Iris Lenses . . . . . . . . . . . .	. .13
External Device Connections . . . . . . . . . . . .	. .14
Flange-back Adjustment . . . . . . . . . . . . . .	. .15
Installation of Camera . . . . . . . . . . . . . . .	. .16
Menu Operation . . . . . . . . . . . . . . . . . . . .	17-18
Language and Camera Identification Settings .	. .19
Exposure Settings . . . . . . . . . . . . . . . . . .	20-24
White Balance Settings . . . . . . . . . . . . . . .	25-27
Day/Night Setting . . . . . . . . . . . . . . . . . .	. .28
Motion Detector Setting (MOTION DET) . . . .29-30

Privacy Masking Setting . . . . . . . . . . . . . . . .31

Special Menu Settings . . . . . . . . . . . . . . .32-37

RS-485 Protocol . . . . . . . . . . . . . . . . . . . . .38

Specifications . . . . . . . . . . . . . . . . . . . . .39-40

Features

This color video camera is designed for use in monitoring system.

•High resolution and high sensitivity with a 1/ 3 inch Super HAD CCD (Charge Coupled Device)

•Line Lock when using AC 24V power.

•C/CS Mount

5

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 6

Features Chart

This page shows the differences between the models.

Models	DAY/NIGHT	WDR	DSS	Power Source
LVC-SX701PC	Yes	Yes	Yes	AC24V (60Hz) / DC12V
LVC-SX701OC	Yes	No	Yes	AC24V (60Hz) / DC12V
LVC-SX701MC	Yes	No	No	AC24V (60Hz) / DC12V

Models LVC-SX701PC are used for the description, operation, and details provided in this operating guide.

6

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 7

Cautions for Safe Operation

Power Supply

This camera must always be operated a AC 24V or DC 12V Certified/Listed, class 2 power supply only. Note: Be careful of AC frequency when the camera

is operated with Line lock mode.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

•Extremely hot or cold places (operating temperature -10 °C - 50 °C, however, we recommend that the unit be used within a temperature range of 0 °C - 45 °C)

•Damp or dust place

•Places exposed to rain

•Places subject to strong vibration

•Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

Handling of the unit

•Remove dust or dirt on the surface of the lens with a blower.

•Use a dry soft cloth to clean the body.If it is very dirty,use a cloth dampened with a small quantity of neutral detergent,then wipe dry.

•Avoid the use of volatile solvents such as thinners,alcohol,benzene,and insecticides.

They may damage the surface finish and/or impair the operation of the camera.

7

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 8

Part Names and Functions

	1	2	3	4	1. Lens mount cap
					The cap is installed to protect the lens mount
					section. Remove the lens mount cap before
					installing a lens (sold separately) .

2. Flange-back adjustment dial

3. Flange-back lock screw

4. Camera installation bracket

The bracket can be fixed at the top or bottom of the camera. (page 16)

8

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 9

Part Names and Functions

5	6	7	5.	Power input terminal
			8	AC 24 V or DC 12 V input terminal
			6.	Video output connector (BNC type)
				Connect this connector to a device such as a
				VCR or monitor with a VIDEO IN connector.
			7.	Power indicator
				Comes on when the power to the camera is on.
			8.	External Device Connectors
				RS-485 Connector
				Connect to an external controller of RS-485 format.

Alarm Output Terminal (ALARM OUT/GND)

Connect to the alarm input of an external device.

Multi Input Terminal

Connect to an external wired remote control.

9

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 10

Part Names and Functions

	9	10	11	9. Buttons for menu
				To set items on the MEMU, use the these but-
				tons on the side panel. (page 17)

10. ALC Lens Setting Switch

DC: When you attach an Auto Iris lens requiring the DC control signal, please put this switch in the DC position.

ELC: When you attach a manual or fixed lens, please put this switch in the ELC position. VIDEO: When you attach an Auto Iris lens requiring the video control signal, please put this switch in the VIDEO position.

11. Lens iris output connector (LENS)

This 4- pin connector is used to send the Iris control signal and power supply to an autoiris type lens.

10

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 11

Connections

3		Basic connection
2		The peripheral devices (VCR, monitor, lens, etc.),
		AC adaptor and cables are not supplied.
		1. Connecting the monitor
		Make the video signal connection between the
		camera and the monitor or time lapse VCR.
		2. Use a commercially available AC 24 V
		adaptor.
	1	Connect an AC 24 V power source to the AC 24V
		input terminal on the back of the camera.
		3. Insert the plug of this power cord into a wall
		outlet.
		The POWER indicator will light. Adjust the pic-
		ture on the monitor using the Brightness and
		Contrast controls etc.

To monitor’s Video Input or Camera Input

11

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 12

Mounting the Lens

1

2-2

3

2-1

1.Remove the lens mount cap from the camera.

2.Install the auto-iris lens.

2-1. CS mount type lens

Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.

2-2. C mount type lens

To allow for flangeback adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with the camera opening and turn the lens slowly to install it.

3.Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.

When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.

In such a case, remove the original plug and using a soldering iron, connect a lens iris plug according to the diagram. (Refer to next page.)

12

LVC-SX701PC_AABBSL_ENG 5/20/06 9:47 AM Page 13

Concerning Auto-Iris Lenses

DC type auto-iris lens

A lens without driver circuit

a DC power source. In general, referred to as DC type coil

Setting Switch to the DC position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the ALC Lens Setting Switch to the VIDEO position.)

CAUTION: Be cautions not to use Auto Iris Lens with over 50mA.

auto-iris lens

or fixed iris lens (Set the ALC Lens

to the ELC position.)

VIDEO type auto-iris lens

and LEVEL controls on the lens to iris. Normally the ALC volume should all the way to Av (Average).

on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL volume on the lens casing to correct.

Pin layout for the lens iris output connector

No.	DC type lenses	VIDEO type lenses
1	Damp -
		Vcc (+12V)
2	Damp +
		Not used
3	Drive +	Video
4	Drive -	Ground

13