LG LVC-C553, LVC-C513, LVC-C510, LVC-C503, LVC-C530 User Manual

Operating Instructions

LVC-C500
LVC-C503
LVC-C510
LVC-C513
LVC-C530
LVC-C533
LVC-C553

Before installing and using the camera,
please read these instructions thorough­ly and retain them for later reference.

2

CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER(OR BACK) NO USER SERVICE-

ABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SER-

VICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the prod­uct’s enclosure that may be of suffi­cient magnitude to constitute a risk of
electric shock to persons.

This symbol is intended to alert the
user to the presence of important
operating and maintenance (servic­ing) instructions in the literature
accompanying the appliance.

Warning

To prevent fire or shock hazard,do not expose the unit to rain or moisture.
To avoid electrical shock,do not open the cabinet. Refer servicing to quali­fied personnel only.
Wiring methods shall be in accordance with the National Electric
Code, ANSI/NFPA 70.

Regulatory Notices For U.S.A

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interfer­ence when the equipment

is operated in a commercial environment.

This equipment

generates, uses, and can radiate radio frequency ener­gy and, if not installed and used in accordance with the instruction manu­al, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the

cable entries of this product in the end user.

• Caution:Danger of explosion if battery is incorrectly replaced. Replaced

only with the same or equivalent type recommended by the manufactur­er. Dispose of used batteries according to the manufacturer’s instruc­tions.

• Holes in metal, through which insulated wires pass, shall have smooth

well rounded surfaces or shall be provided with brushings

.

Warning

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Contents and Features

3

Contents

Contents and Features . . . . . . . . . . . . . . . . . . . . . . . . .3

Cautions for Safe Operation

. . . . . . . . . . . . . . . . . . . . . .4

Operating Controls and Their Functions . . . . . . . . . . .5

Power IN / CONTROL / External Key(A/D IN) . . . . .6-14

MENU DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . .15

CAMERA ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

FOCUS MODE SET . . . . . . . . . . . . . . . . . . . . . . .17-19

AWB SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

AE SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24

AE LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

SPECIAL SET . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27

MOTION DET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

F OSD SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

P MASKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-32

On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . .33-34

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-36

Features

The power zoom color video camera is designed for use in
monitoring system.

• High resolution and high sensitivity with a 1/4 inch
Exview/HAD/CCD (Charge Coupled Device)

• High magnitude of zoom lens with optical X 27,
Digital X 54 (LVC-C503/C513/C533/C553),
Digital X 324 (LVC-C500/C510/C530)

• Auto Focus / Auto White balance

• Auto exposure with DC Iris control

• Day & Night function

• DSS (Digital Slow Shutter) is available: Optional

• WDR (Wide Dynamic Range) is available: Optional

• Privacy Zones: Optional

Cautions for Safe Operation

4

Power Supply

This camera must always be operated a 12V DC
power supply.

Handling of the unit

Be careful not to spill water or other liquids on the
unit, or to get combustible or metallic material
inside the body. If used with foreign matter inside,
the camera is liable to fail, or to be a cause of fire
or electric shock.

Operating and storage location

Avoid viewing a very bright object (such as light
fittings) for an extended period. Avoid operating or
storing the unit in the following locations.

• Extremely hot or cold places
(operating temperature 0°C-45°C)

• Damp or dust place

• Where it is exposed to rain

• Where it is subject to strong vibration

• Close to generators of powerful electromagnetic

radiation such as radio or TV transmitters.

Care of the unit

• Remove dust or dirt on the surface of the lens
with a blower.

• Use a dry soft cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity
of neutral detergent, then wipe dry.

• Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and insecticides.
They may damage the surface finish and/or
impair the operation of the camera.

Operating Controls and Their Functions

5

1. Tripod adapter

This adapter can also be attached on the bottom of the camera.

2. Lens mount cap

3. TELE Key

When push the TELE KEY, picture is telephoto

4. WIDE Key

When push the WIDE KEY, picture is wide angle

5. Focus Near Key

In a manual situation, focus get near.

6. Focus Far Key

In a manual situation, focus get far.

7. Menu Key

If you want to set up a diverse function, you can push this button.

8. Video output (S-Video type)

Connect to the S-Video in connector of a monitor.

9.

Interface of camera control JACK (6 Pin Din Jack Type)

• Connect to an external voltage controller

• You can supply a camera with power from this. (DC12V)

10. Video output (BNC type)

Connect to the video in connector of a monitor.

1

Model: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

2

6

Power In / Control

You can adjust focus and zoom by a pin terminal on the back side
of the camera.

1

4

3

5

6

2

*

is the color of the cable. (If it is offered)

Adjust voltage from 1 pin and 2 pin

Model: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

7

Model: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

External Key (A/D IN)

Schematic diagram of wired
remote-control

8

Operating Controls and Their Functions

1. Tripod adapter

This adapter can also be attached on the bottom of the camera.

2. Lens mount cap

3. TELE Key

When push the TELE KEY, picture is telephoto

4. WIDE Key

When push the WIDE KEY, picture is wide angle

5. Focus Near Key

In a manual situation, focus get near.

6. Focus Far Key

In a manual situation, focus get far.

7. Menu Key

If you want to set up a diverse function, you can push this button.

8. Video output (S-Video type)

Connect to the S-Video in connector of a monitor.

9.

Interface of camera control JACK (12 Pin Din Jack Type)

• Connect to an external voltage controller

• You can supply a camera with power from this. (DC12V)

10. Video output(BNC type)

Connect to the video in connector of a monitor.

1

Model: LVC-C530, LVC-C533

2

9

Power In / Control

You can adjust focus and zoom by a pin terminal on the back side
of the camera.

*

is the color of the cable.(If it is offered)

Model: LVC-C530, LVC-C533

10

Power In / Control

Model: LVC-C530, LVC-C533

11

External Key (A/D IN)

Schematic diagram of wired
remote-control

Model: LVC-C530, LVC-C533

12

Model: LVC-C553

Operating Controls and Their Functions

1. Tripod adapter

This adapter can also be attached on the bottom of the camera.

2. Lens mount cap

3. TELE Key

When push the TELE KEY, picture is telephoto

4. WIDE Key

When push the WIDE KEY, picture is wide angle

5. Menu Key

If you want to set up a diverse function, you can push this button.

6.

Control JACK (RJ45)

Connect RS-422 interface

7. Focus Far Key

In a manual situation, focus get far.

8. Focus Near Key

In a manual situation, focus get near.

9. DC 12V screw terminal

Connect to an external power supply of DC 12V.

10. Hot Key

Use to day & night switching get mode.

11. Video output(BNC type)

Connect to the video in connector of a monitor.

1

2

13

Model: LVC-C553

Connections

Power Connection

1. Remove the insulation on the power cable as illustrated.

2. Attach the terminal tips.

3. Connect to the 12V DC UL Listed, Class 2 Power
Supply only on the camera.

Connection the monitor

1. To VIDEO OUT

2. To Video input on the monitor

123

1 2

14

Control

Remote Control Lines are connected to RJ-45 socket as
shown below.

In case of Zoom/Focus DC control Interface(option)

Voltage Range

7T-

8T+

T+

T-

R-

R+

CONTROL OUT Controller

PIN 8 PIN 1

CONTROL

In case of RS-485 INTERFACE (Basic)

4 ZOOM

5 COMMON

6 FOCUS

ZOOM(+Tele, -Wide)

COM

FOCUS(+Near, -Far)

Receiver/Controller

+ Vcom + (+5~15V)

- Vcom - (+5~15V)

Model: LVC-C553

15

MENU DESCRIPTIONS

Using TELE, WIDE, F. NEAR, F. FAR button

• TELE and WIDE are used for UP and DOWN.

• FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.

16

CAMERA ID

1. CAMERA ID

To connect a large number of camera , It can be
assigned to identification number to each camera for
camera control easily.
(OFF, 0 - 255: total numbers of ID are 256)

• It only can be set this function using ID commend.
To transfer ID Code of camera , In first byte at PC control.
Set the ID number of camera , and then the ID number
display continuously.

17

2. Focus Set:

2-1. Focus Mode Set
This function is for focus mode setting

A) Set up “FOCUS SET” in main menu using Tele/Wide key.

Select the “FOCUS MODE” in submenu using Tele/Wide
key. And then set the mode (Auto, Push auto, or Manual)
using Focus key.

2-2. Focus Distance Set
This function is for selection of minimum shooting
distance.

A) Select the “FOCUS DIST” in submenu using Tele/Wide key.
B) Set the focus distance mode from 1cm to 5M. (1cm, 10cm,

50cm, 1M, 3M, 5M) using Focus key.

2-3. ZOOM START Set
This function is for selection of zoom start position.

A) Select the “ZOOM START” in submenu using Tele/Wide
key.
B) Set the Zoom start mode from x1 to x26 using Focus key.

FOCUS MODE SET

FOCUS MODE SET

18

2-4. ZOOM END Set
This function is for selection of zoom end position.

A) Select the “ZOOM END” in submenu using Tele/Wide key.
B) Set the Zoom end mode using Focus key.

LVC-C503/C513/C533/C553: from (Zoom Start + 1) to X54
LVC-C500/C510: from (Zoom Start + 1) to X324

2-5. ZOOM SPEED Set
This function is for selection of zoom speed.

A) Select the “ZOOM SPEED” in submenu using Tele/Wide key.
B) Set the Zoom speed, Slow, Middle , Quick using Focus key.

2-6. ZOOM TRACKING MODE Set
This function is for selection of zoom tracking mode.

A) Select the “ZTRK” in submenu using Tele/Wide Command,
B) Set the Zoom tracking mode to Auto or Manual.

* Zoom tracking means focused zooming state.

19

FOCUS MODE SET

2-7. INITIAL SET
If initial mode set to ON, All FOCUS SET function is
changed to the factory setting.

A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF using Focus key.

2-8. RETURN TO MAIN MENU
This function is exit to main menu.

A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode using Focus key.

3. AWB SET
3-1. WB Mode Set
This function is for changing the WB mode.

A) Set up “AWB SET” in main menu using Tele/Wide key.
B) Select the “WB MODE” in submenu using Tele/Wide key.
C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor using
Focus key.

*WBC MODE: Use for changing White Balance Mode .

1) AUTO: WB Range 2500°K ~ 9500°K .

2) PUSH AUTO: Set the AWB mode to Push Auto, then WB Mode

is auto.

3-2. RED ADJUST Set
This function is available for Manual WB mode.
This mode is the adjustment of user option for special color.

A)

Select the “RED ADJUST” in submenu using Tele/Wide key.

B) Adjust the level from (0-255 MANUAL) using Focus key.

AWB SET (Auto White Balance)

20

AWB

WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN

AUTO
NOT USE
NOT USE
ON

AWB SET (Auto White Balance)

21

3-3. BLUE ADJUST Set
This function is available for Manual WB mode.
This mode is the adjustment of user option for special
color.

A) Select the “BLUE ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from (0-255 MANUAL) using Focus key.

3-4. PUSH AUTO
In case of PUSH AUTO WB mode.
Adjust the push auto mode ON, WB act automatically.
3-5. INITIAL SET
If initial mode set to ON, All AWB function is changed
to the factory setting

A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF using Focus key.

3-6. RETURN TO MAIN MENU
This function is exit to main menu.

A) Select the “RETURN “ in submenu. Using Tele/Wide key.
B) Set the return mode using Focus key.

AWB

WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN

AUTO
NOT USE
NOT USE
ON

4. AE SET
4-1. AE Mode Set
This function is for changing to AE mode.

A) Set up “AE SET” in main menu using Tele/Wide key.
B) Select the “AE MODE” in submenu using Tele/Wide key.
C) Set the mode auto, IRIS MAN, SLOW MAN, SHUTTER MAN,
Auto using Focus key
Note: SLOW MAN option is not available for LVC-C500,
LVC-C510, and LVC-C530.

4-2. IRIS ADJUST Set
This function is available for IRIS MAN mode.

A)

Select the “IRIS ADJUST” in submenu using Tele/Wide key.

B) Adjust the level from 0 to 255 using Focus key.

4-3. AGC ADJUST Set
This function is available for SLOW MAN mode /
SHUTTER MAN mode .

A) Select the “IRIS ADJUST” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 7 using Focus key.

AE SET (Auto Exposure)

22

AE SET (Auto Exposure)

23

4-4. BRIGHTNESS ADJUSTMENT Set
This function is available for AUTO mode.

A) Select the “BRIGHTNESS” in submenu using Tele/Wide key.
B) Adjust the level from

0 to 255

using Focus key.

4-5. BACKLIGHT Set

A) Select the “BACKLIGHT” in submenu using Tele/Wide key.
B) Set the mode OFF, ON, or AUTO, WDR using Focus key.
* WDR (Wide Dynamic Range): It makes possible to capture both

high luminance and low luminance subject.

* Auto BLC (Auto back light compensation)

When a back light condition occurs in area1,area2, area3, or area4.
the back light compensation is enable. When the back light
condition disappears in that area, BLC is disable automatically.
If do not want this mode, set to OFF

4-6. E SENSITIVE
This function is available for SLOW mode / AUTO mode.

A) Select the "E SENSITIVE" in submenu using Tele/Wide key.
B) •Adjust the level from X1 FIX to X20 FIX using Focus key.

(SLOW mode)

•

Adjust the level from X1 AUTO to X20 AUTO using Focus key.
(AUTO mode)

Auto BLC

Note: WDR option is not available
for LVC-C500, LVC-C510, and
LVC-C530.

Area1

Area0

Area4

Area3

Area2

4-7. FLICKERLESS Set
This function is available for AUTO mode.

A) Select the “FLICKERLESS” in submenu using Tele/Wide key.
B) Set the mode OFF, ON using Focus key.

* FLICKERLESS: Use for removing the flicker of picture

ON: Remove the flicker
(In case of PAL System: Shutter Speed 1/120 sec).

4-8. SHUTTER SPEED Set
This function is available for AUTO mode / SHUTTER
mode.

A) Select the “SHUTTER” in submenu using Tele/Wide key.
B) • Set the mode NORMAL, 1/120 - 1/50000 using Focus key.

(NTSC)

• Set the mode NORMAL, 1/125 - 1/50000 using Focus key.
(PAL)

4-9. INITIAL SET

A) Select the “INITIAL SET” in submenu using Tele/Wide Command.
B) Set the initial set mode to ON or OFF using Focus key.

4-10. RETURN TO MAIN MENU
This function is exit to main menu.

A) Select the “RETURN “ in submenu using Tele/Wide key.
B) Set the return mode using Focus key.

AE SET (Auto Exposure)

24

AE LEVEL (Auto Exposure)

25

5-1. BLC LEVEL Set
This function is for change to BLC LEVEL.

A) Select the “BLC LEVEL” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.

5-2. WDR LEVEL SET
This function is for change to WDR LEVEL.

A) Select the “WDR LEVEL” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 15 using Focus key.

5-3. INITIAL SET

A) Select the “INITIAL SET” in submenu using Tele/Wide

Command,

B) Set the initial set mode to ON or OFF using Focus key.

5-4. RETURN TO MAIN MENU
This function is exit to main menu.

A) Select the “RETURN” in submenu using Tele/Wide key.

B) Set the return mode using Focus key.

SPECIAL SET

26

6. SPECIAL SET
6-1. User Title Set

This function is for custom title on screen display.

A) Set “SPECIAL SET” in main menu using Tele/Wide key.
B) Select the “USER TITLE” in submenu using Tele/Wide key.
C) Set the position of title and set data using Tele/Wide, Focus

key.

6-2. SHARPNESS ADJUST Set

A) Select the “SHARPNESS” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 255 using Focus key.

6-3. COLOR Set
This mode is for B/W mode.

A) Select the “COLOR” in submenu using Tele/Wide key.
B) Select the mode ON, OFF using Focus key.

6-4. NEGATIVE Set
This mode is to change color and luminance to
negative.

A) Select the “NEGATIVE” in submenu using Tele/Wide key.
B) Select the mode ON, OFF using Focus key.

SPECIAL SET

27

6-5. D EFFECT Set

This function is to scroll to mirror relevanced
function.

A) Select the “D EFFECT” in submenu using Tele/Wide key.
B) Set the mode, none, mirror, v-flip, rotation using Focus key.

6-6. INITIAL SET

If initial mode set to ON, All SPECIAL functions are
changed to the factory setting

A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF Using Focus key.

6-7. RETURN TO MAIN MENU

This function is exit to main menu.

A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode Using Focus key.

MOTION DET

28

7. MOTION DETECTION SET
7-1. DETECTION Mode Set

A) Set “MOTION” in main menu using Tele/Wide key.
B) Select the “DETECTION” in submenu using Tele/Wide key.
C) Set the mode ON, OFF using Focus key.

7-2. LEVEL ADJUST Set
This function is available for DETECTION mode.

A) Select the “LEVEL SET” in submenu using Tele/Wide key.
B) Adjust the level from 0 to 21 using Focus key.

7-3. DAY/NIGHT Set
This function is available for DETECTION mode.

A) Select the “DAY/NIGHT” in submenu using Tele/Wide key.
B) Select a mode using Focus key (AUTO, DAY, NIGHT).
Note: This function is fixed to "DAY" for model LVC-C500/C503.

7-4. INITIAL SET
If initial mode set to ON, All MOTION functions are
changed to the factory setting

A) Select the “INITIAL SET” in submenu using Tele/Wide key.
B) Set the initial set mode to ON or OFF Using Focus key.

7-5. RETURN TO MAIN MENU
This function is exit to main menu.

A) Select the “RETURN” in submenu using Tele/Wide key.
B) Set the return mode Using Focus key.

F OSD DISP (Function On Screen Display)

29

8. F OSD DISP
8-1. FUNCTION Set

A) Set “F OSD” in main menu using Tele/Wide key.
B) Select the mode what you want in submenu using Tele/Wide

key.

C) Set the display mode of OSD ON, OFF using Tele/Wide,

FOCUS key.

*INITIAL SET and RETURN are the same as before procedure.

P MASKING (Privacy Masking)

30

9. P MASKING
9-1.AREA SEL

This function is to selecting to privacy masking area.

A) Set “P MASKING” in main menu using Tele/Wide key.
B) Select the “AREA SEL” in submenu using Tele/Wide key.
C) Select the area from area 1 to area 8 using Focus key.

9-2. Masking

This function is available for MASKING mode.

A) Select the “MASKING” in submenu using Tele/Wide key.
B)

Select

the mode ON/OFF using Focus key.

9-3. P MODE SET

This function is available to go to the PRIVACY
MASKING SETTING mode.

A) Select the “P MODE SET” in submenu using Tele/Wide key.
B) If PM SET END mode goes to ON, this menu automatically

goes OFF.

9-4. MOVE PT SET

Select to point which wants to move.

A) Select the “MOVE PT SET” in submenu using Tele/Wide key.
B) Select the mode ALL X, ALL Y, LEFT X, LEFT Y, RIGHT X,

RIGHT Y using focus key.

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

P MASKING (Privacy Masking)

31

9-5. MOVE PT CNT

This function is available to move selected point in the
MOVE PT SEL.

A) When MOVE PT SEL is selected ALL* : Available to move

area.

B)

When MOVE PT SEL is selected LEFT* or RIGHT* : Change
the size of the area

9-6. PM SET END

Privacy Masking setting function is available to set OFF.

A) Select the “PM SET END” in submenu using Tele/Wide key.
B) If P MODE SET mode goes to ON, P MODE SET

automatically goes OFF.

9-7. INI COLOR

This function is to selecting to color of initial masking.

A) Select the “INI COLOR” in submenu using Tele/Wide key.
B) Select the mode from color 1 to color 8 using focus key.

9-8. COLOR

After setting, select the masking color.

A) Select the “COLOR” in submenu using Tele/Wide key.
B) Select the mode from color 1 to color 8 using focus key.

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

P MASKING (Privacy Masking)

32

9-9. INITIAL SET :

A) Select the “INITIAL SET” in submenu using Tele/Wide

Command,

B) Set the initial set mode to ON or OFF using Focus key.

9-10. RETURN TO MAIN MENU :
This function is exit to main menu.

A) Select the “RETURN “ in submenu using Tele/Wide key.

B) Set the return mode using Focus key.

* You can not set “P MASKING” mode in the digital zoom

position.

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

On Screen Display

33

Some of these functions will
be displayed every time the
camera is operated and then
disappeared after 5 seconds.

FUNCTION OSD Format Description

1. Focus Mode Non display Auto Mode

Manual / push Auto Mode

2. Back Light Non display Back Light OFF

“BL”display BLC ON / Auto BLC Mode

3. Shutter Speed Non display Normal Shutter (PAL: 1/50)

“Ff”display Flickerless Mode

1/120 * 10 variable steps.

1/50,000

4. STAND-BY Indicate the camera stand-by during the
camera’s power turning ON.

5. CAMERA ID According to write the identification number to
each camera, Multi-point control is available
(PC Control 000~255).

12 3 6

475

* Shutter Speed

1/120 - 1/50000: NTSC

* Shutter Speed

1/125 - 1/50000: PAL

On Screen Display

34

FUNCTION OSD Format Description

6. WBC Mode

White Balance AUTO

WB Preset for INDOOR (3200°K)

Wb Preset for OUTDOOR (5100°K)

Manual WB Adjustment: In manual mode the HUE control is
available (0 ~ 255).

Push Auto White Balance: Turn this mode ON, the white trace
automatically. Turn this mode OFF, preserve the white of final
auto tracing action (Manual).

7.

ZOOM Display

DX 54 Digital Zoom mode (LVC-C503/C513/C533/553)

DX 324 Digital Zoom mode (LVC-C500/C510/C530)

X 27 Optical Zoom mode

M

W

P

W

Specifications

35

Image device 1/4"EXVIEW HAD CCD

NTSC, High resolution : 811(H) X 508(V) 410K

PAL, High resolution : 795 (H) X 596 (V) 470K

Horizontal resolution

Approx. 520 TV Line.

Lens X 27 Zoom (F 1.5 (W), F 3.8 (T) f= 3.25 ~ 88.0 mm), Video AF

Digital Zoom Ratio X 2: Basic (OFF at WDR mode)

X 12: Basic (LVC-C500, LVC-C510, LVC-C530)

Minimum illumination Normal Mode : 1 Lux (F 1.5, Normal Shutter)

(1/3 output) Electronic Shutter Speed Mode :

0.01 Lux (X20 Field Accumulate)

Night Mode : 0 Lux (Infrared ON)

S/N More than 48dB
Scanning System 2:1 Interlace

Scanning Frequency(H) 15.734 kHz (NTSC), 15.625 kHz (PAL)

Scanning Frequency(V) 60Hz (NTSC), 50Hz (PAL)

Privacy Zones 8 area active programmable zones

Specifications are subject to change without notice.

36

Specifications

Focal Length 3.24mm (WIDE), 86mm (TELE)

OSD(On Screen Display) English

Power requirement DC 12V

Video output

Composite Output 75Ω Terminated / Y,C Separated

Power consumption 5.4W: LVC-C503, LVC-C513, LVC-C533, LVC-C553

5.1W: LVC-C500, LVC-C510, LVC-C530

operating temperature 0°C - 45°C

Operating Humidity 0% RH - 60% RH

Storage temperature -20°C - 60°C, 0% RH - 85% RH

Dimensions 57mm(W) X 62.4mm(H) X 98.5mm(D)

Weight

500

g

Specifications are subject to change without notice.

P/NO: 3834RS0075A

ݷᔫᒎฉ

LVC-C500
LVC-C503
LVC-C510
LVC-C513
LVC-C530
LVC-C533
LVC-C553

在您使用此摄像机之前，请完整阅读此操
作指南以供参考。

2

ቃቦ : 为了减少电击的危险 请勿拆下前

盖 或后盖 内部没有任何用户可以维修

的零部件

如需维修 请联系专业维修人员

电击危险请勿打开

ቃቦ

此符号用于警示用户，产品外壳存在
未绝缘的危险电压，会产生对人身造
成电击的危险。

此符号用于提醒用户，随设备一起提
供的印刷品中包含重要的操作和维护

（维修）指南。

வস

为了防止电击事故，请不要将该产品暴露在雨中或潮湿的环境中。
为了避免电击的危险，请不要打开机壳，如需维修，请联系专业维
修人员。
接线方法应该符合美国国家电气规程 ANSI/NFPA 70 之规定

ࢾဉී U.S.A

本产品经测试符合 FCC 第 15 部分有关 A 类数字设备的限制条件
这些限制条件是为提供合理的保护措施 防止在商业环境中安装设
备时产生有害干扰而制定的

本产品会产生 使用和辐射无线电频

率能量

如未正确安装和使用 可能对无线电通讯造成有害干扰
在住宅环境中使用此产品会产生有害干扰 在此情况下用户需要自
行采取措施消除此干扰

•

终端用户使用的此产品的电缆入口中提供了合适的导管引入装置
剔除装置或密封套

•

小心 : 如果电池更换不当 则会有爆炸的危险 请使用同一型号或
制造商建议的电池型号

请按照制造商的说明处置废旧电池

•

绝缘线穿过的金属孔应当具有光滑 圆形的表面 或者应当是刷
光的

வস

۾ޘອᆐ A ಢޘອăᏴᓕᐤણஹሆဧ፿۾ޘອဟLj჈భถ્ޘည
࢟ࠟছཷLjᏴࠥ༽ౚሆ፿ઓኊገݧནሤ።ࡼࡅဗă

ดྏᄂ࢛

3

෹ഺ

ดྏᄂ࢛ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ڔཝݷᔫᓖፀူሲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ݷᔫ఼ᒜૺ໚৖ถ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

࢟Ꮞၒྜྷ / ఼ᒜ / ᅪݝ୆ (A/D IN) . . . . . . . . . . . . . . . .6-14

ݩ࡝ႁී . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

摄像机 ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

对焦模式设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-19

AWB 设置

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

AE 设置

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-24

AE 级别

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

特殊设置 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27

运动检测 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

F OSD 显示 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

P MASKING (保密掩盖) . . . . . . . . . . . . . . . . . . . .30-32

ື෵ݩ࡝መာ (OSD) . . . . . . . . . . . . . . . . . . . . . . . . .33-34

ৃ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-36

ᄂ࢛

此电动变焦彩色摄像机是为监视系统专门设计的。

• 高分辨率

高灵敏度的 1/4 英寸 Exview/HAD/CCD

电荷耦合装置

• 高倍数变焦镜头 光学变焦 X 27
数码变焦 X 54 (LVC-C503/C513/C533/C553),
数码变焦 X 324 (LVC-C500/C510/C530)

• 自动对焦 / 自动白平衡

• DC 光圈控制自动曝光

• 白天 & 黑夜功能

•DSS

数字慢速快门 : 可选

• WDR 宽动态范围 : 可选

• 保密区域 : 可选

ڔཝݷᔫᓖፀူሲ

4

࢟Ꮞ

此摄像机必须始终使用 12V DC 电源

ۃᏥ࿳ስ૦

请注意不要将水或其它液体溅到摄像机内部

也不
要让可燃性物品或金属物品掉入摄像机内 如果摄
像机内部有杂质

则可能会导致摄像机故障或引发

火灾或电击

ဧ፿ࡀ࢐࢛

不要长时间观看过于明亮的物体

如灯具 避免在

以下环境中使用或存放此设备

• 过热或过冷的地方 工作温度 0°C-45°C)

• 潮湿或有灰尘的地方

• 有雨的地方

• 有强烈振动的地方

• 靠近有强电磁辐射的地方 如收音机或电视发射

机附近

࿳ስ૦ۣዸ

• 使用吹风机将表面的灰尘或脏物吹掉

• 请使用软布清洁机身 如果太脏 请使用带有少

量中性清洁剂的软布清洁 然后擦干

• 请不要使用挥发性溶剂 如稀释剂 酒精 苯和
杀虫剂 们会损坏表面或机身

ݷᔫ఼ᒜૺ໚৖ถ

5

1. ྯ୭ଦᓞ୻໭

此转接器还可以安装到摄像机的底部

2. ஻ᄿڔᓤঙ

3. TELE ୆

当按 TELE KEY 时 图像为远距拍摄

4. WIDE ୆

当按 WIDE KEY 时 图像为广角拍摄

5. ౯தୡ௦୆

在手动操作时 将焦距拉近

6. ౯Ꮠୡ௦

在手动操作时 将焦距拉远

7. ݩ࡝୆

如果您要设置不同的功能 可按此键

8. ၁ຫၒ߲ S-Video ቯ

连接到监视器的 S-Video 输入接口

9. ࿳ስ૦఼ᒜ JACK ୻ా 6 ᑣ DIN JACK ቯ

• 连接到外部电压控制器

• 您可以通过此接口为摄像机供电 (DC12V)

10. ၁ຫၒ߲ BNC ቯ

连接到监视器的视频输入接口

1

2

ቯ: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

6

࢟Ꮞၒྜྷ0఼ᒜ

您可以通过摄像机背面的针形端子调节焦距和变焦。

1

4

3

5

6

2

*

为电缆颜色。（如果提供）
调节管脚 1 和管脚 2 的电压

ቯ: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

变焦 & 焦距 DC 控制

A/D KEY 1 输入

共地变焦 & 对焦
通用地

电源输入 12V

7

ቯ: LVC-C500, LVC-C503,

LVC-C510, LVC-C513

ᅪݝ୆ (A/D IN)

线控示意图

8

ݷᔫ఼ᒜૺ໚৖ถ

1. ྯ୭ଦᓞ୻໭

此转接器还可以安装到摄像机的底部

2. ஻ᄿڔᓤঙ

3. TELE୆

当按 TELE KEY 时 图像为远距拍摄

4. WIDE୆

当按 WIDE KEY 时 图像为广角拍摄

5. ౯தୡ௦୆

在手动操作时 将焦距拉近

6. ౯Ꮠୡ௦

在手动操作时 将焦距拉远

7. ݩ࡝୆

如果您要设置不同的功能 可按此键

8. ၁ຫၒ߲ S-Video ቯ

连接到监视器的 S-Video 输入接口

9. ࿳ስ૦఼ᒜ JACK ୻ా 12 ᑣ DIN JACK ቯ

• 连接到外部电压控制器

• 您可以通过此接口为摄像机供电 (DC12V)

10. ၁ຫၒ߲ BNC ቯ

连接到监视器的视频输入接口

1

2

ቯ: LVC-C530, LVC-C533

9

࢟Ꮞၒྜྷ0఼ᒜ

您可以通过摄像机背面的针形端子调节焦距和变焦。

*

为电缆颜色。（如果提供）

ቯ: LVC-C530, LVC-C533

用于 RS-232C 发送端口
用于 RS-232C 接收端口

变焦 & 焦距 DC 控制

通用地
遥控输入
用于运动检测脉冲输出

电源输入 12V

A/D KEY 1 输入
A/D KEY 2 输入
A/D KEY 3 输入

10

࢟Ꮞၒྜྷ0఼ᒜ

ቯ: LVC-C530, LVC-C533

• RS232S ೌ୻

• ܤୡ & ୡ௦ DC ఼ᒜೌ୻

୻၃໭࡝Ꮔ / ఼ᒜ໭

• ۨவၒ߲ Ꮵࣅଶހၒ߲ ൴ߡᄟୈ

Ꮵࣅଶހ

11

ᅪݝ୆ (A/D IN)

线控示意图

ቯ: LVC-C530, LVC-C533

镜像

12

ቯ: LVC-C553

ݷᔫ఼ᒜૺ໚৖ถ

1. ྯ୭ଦᓞ୻໭

此转接器还可以安装到摄像机的底部

2. ஻ᄿڔᓤঙ

3. TELE୆

当按 TELE KEY 时 图像为远距拍摄

4. WIDE୆

当按 WIDE KEY 时 图像为广角拍摄

5. ݩ࡝୆

如果您要设置不同的功能 可按此键

6. ఼ᒜރ఻ (RJ45)

连接 RS-422 接口

7. ౯Ꮠୡ௦

在手动操作时 将焦距拉远

8. ౯தୡ௦୆

在手动操作时 将焦距拉近

9. DC 12V ൛ႋ࣡ᔇ

连接到 DC 12V 外部电源

10. ེ୆

使用此键切换白天 & 黑夜模式

11. ၁ຫၒ߲ BNC ቯ

连接到监视器的视频输入接口

1

2

13

ቯ: LVC-C553

ೌ୻

࢟Ꮞೌ୻

1. 如图所示去掉电源线外面的绝缘层

2. 装上端子头

3. 连接 12V DC UL Listed Class 2 电源到摄像机

ೌ୻ପ၁໭

1. 到 VIDEO OUT

2. 到监视器上的视频输入

123

1 2

14

఼ᒜ

遥控线连接到下面的 RJ-45 插孔

对于变焦/对焦 DC 控制接口 可选

电压范围

7T-

8T+

T+

T-

R-

R+

PIN 8 PIN 1

CONTROL

对于 RS-485 接口 基本

4

5

6

+ Vcom + (+5~15V)

- Vcom - (+5~15V)

ቯ: LVC-C553

控制输出

控制器

接收器/控制器

15

ݩ࡝ႁී

ဧ፿ TELE WIDE F. NEAR F. FAR ږ฽

• TELE 远摄 和 WIDE 广角 用于 UP 拉近 和 DOWN 拉远

• FOCUS+ 拉长焦距 和 FOCUS- 拉近减少 用于 INCREASE 增加 和

DECREASE

减少 数据

16

࿳ስ૦ ID

1. ࿳ስ૦ ID

当连接多台摄像机时

可以为每台摄像机指定一个识别

码 这样就可以更容易的对每台摄像机进行控制

(OFF, 0 - 255 ID 总数为 256)

• 只能使用推荐的 ID 来设置此功能

要发送摄像机的 ID 代码 使用 PC 控制的第一个字节
设置摄像机的 ID 编号 然后 ID 编号将连续显示

17

2. ࣪ୡ࿸ᒙǖ
2-1. ࣪ୡෝါ࿸ᒙ

ࠥ৖ถ፿᎖࿸ᒙ࣪ୡෝါ

A)使用 Tele/Wide 键在主菜单中设置 FOCUS SET

使用 Tele/Wide 键选择子菜单中的 FOCUS MODE 然后
使用对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual (手动))

2-2. ࣪ୡ௦ಭ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋᔢቃ๜࿳௦ಭ

A) 使用 Tele/Wide 键选择子菜单中的 FOCUS DIST
B) 使用对焦键在 1cm 到 5M 之间设置对焦距离模式 (1cm,

10cm, 50cm, 1M, 3M, 5M)

2-3. ܤୡఎဪ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋܤୡఎဪᆡᒙ

A) 使用 Tele/Wide 键选择子菜单中的 ZOOM START
B) 使用对焦键在 x1 到 x26 之间设置变焦开始模式

࣪ୡෝါ࿸ᒙ

࣪ୡෝါ࿸ᒙ

18

2-4. ܤୡஉၦ࿸ᒙ

ࠥ৖ถ፿᎖ኡᐋܤୡஉၦᆡᒙă

A) 使用 Tele/Wide 键选择子菜单中的 ZOOM END
B) 使用对焦键设置变焦结束模式

LVC-C503/C513/C533/C553:从 变焦开始 + 1 到 X54
LVC-C500/C510:从 变焦开始 + 1 到 X324

2-5. ܤୡႥࣞ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋܤୡႥࣞă

A) 使用 Tele/Wide 键选择子菜单中的 ZOOM SPEED
B) 使用对焦键设置变焦速度 Slow 低 Middle 中 Quick 快

2-6. ܤୡৌᔍෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋܤୡৌᔍෝါ

A) 使用 Tele/Wide 命令选择子菜单中的 ZTRK
B) 将变焦跟踪模式设置为 Auto 自动 或 Manual 手动
* ܤୡৌᔍᒎ௡ୡܤୡᓨზ

19

࣪ୡෝါ࿸ᒙ

2-7. ߱ဪ࿸ᒙ
ྙ߱ဪෝါ࿸ᆐ ON

ఎ Ⴥᎌ FOCUS SET ࣪ୡ࿸ᒙ

৖ถ୓ۻখܤࡵ߲ޣ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

2-8. ૄᓍݩ࡝
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

AWB

WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN

AUTO
NOT USE
NOT USE
ON

3. ᔈࣅڹຳ࿸ᒙ
3-1. ڹຳෝါ࿸ᒙ

ࠥ৖ถ፿᎖ኀখڹຳෝါ

A) 使用 Tele/Wide 键在主菜单中设置 AWB SET
B)

使用 Tele/Wide 键选择子菜单中的 WB MODE
C) 使用对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual(手动) Outdoor(室外) Indoor(室内)

*WBC MODE: ፿᎖ኀখڹຳෝါ

1) AUTO 白平衡范围 2500 °K ~ 9500 °K

2) PUSH AUTO 将 AWB 模式设为 Push Auto 强制自动 则白

平衡模式会自动调整

3-2. ྻࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ Manual WB

၄ࣅڹຳ ෝါ

ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ

A)

使用 Tele/Wide 键选择子菜单中的 RED ADJUST
B) 使用对焦键调节值大小 0-255 MANUAL

AWB ࿸ᒙ ᔈࣅڹຳ

20

AWB ࿸ᒙ ᔈࣅڹຳ

21

3-3. ౸ྻࢯᑳ࿸ᒙ

ࠥ৖ถ፿᎖ Manual WB

၄ࣅڹຳ ෝါ

ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ

A) 使用 Tele/Wide 键选择子菜单中的 BLUE ADJUST
B) 使用对焦键调节值大小 0-255 MANUAL

3-4. PUSH AUTO ༓ᒜᔈࣅ
Ᏼ PUSH AUTO WB ෝါሆ
୓༓ᒜᔈࣅෝါ࿸ᆐ ON WB ્ᔈࣅᒊቲ
3-5. ߱ဪ࿸ᒙ
ྙ߱ဪෝါ࿸ᆐ ON ఎ Ⴥᎌ AWB ᔈࣅڹຳ
৖ถ୓ۻখܤࡵ߲ޣ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

3-6. ૄᓍݩ࡝
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A)

使用 Tele/Wide 键选择子菜单中的 RETURN

B) 使用对焦键设置返回模式

AWB

WBC MODE
RED ADJUST
BLUE ADJUST
INITIAL SET
RETURN

AUTO
NOT USE
NOT USE
ON

4. ᔈࣅ௿࿸ᒙ
4-1. ᔈࣅ௿ෝါ࿸ᒙ

ࠥ৖ถ፿᎖ኀখᔈࣅ௿ෝါă

A) 使用 Tele/Wide 键在主菜单中设置 AE SET
B) 使用 Tele/Wide 键选择子菜单中的 AE MODE
C) 使用对焦键设置模式为 IRIS MAN SLOW MAN SHUTTER MAN

注意 SLOW MAN 选项不适用于 LVC-C500 LVC-C510 和
LVC-C530

4-2. མࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ IRIS MAN ෝါ

A)

使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST

B)

使用对焦键在 0 到 255 中调整设置

4-3. ᔈࣅᐐፄ఼ᒜࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ SLOW MAN/SHUTTER MAN ෝါ

A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST
B)

使用对焦键在 0 到 7 中调整设置

AE ࿸ᒙ ᔈࣅ໎

22

AE ࿸ᒙ ᔈࣅ໎

23

4-4. ೡࣞࢯᑳ࿸ᒙ

ࠥ৖ถ፿᎖ AUTO (ᔈࣅ) ෝါ

A) 使用 Tele/Wide 键选择子菜单中的 BRIGHTNESS
B) 使用对焦键在 0 到 255 中调整设置

4-5. ۳࿸ᒙ

A)

使用 Tele/Wide 键选择子菜单中的 BACKLIGHT
B) 使用对焦键设置模式为 OFF ON 或 ATUO, WDR
* WDR 宽动态范围 用来捕捉高亮度或低亮度物体

* ᔈࣅ BLC ᔈࣅ۳ݗޡ

W

当区域 1 区域 2 区域 3 或区域 4 中的背光满足条件时
可使用背光补偿 当此区域中的背光条件消失时 BLC 自动
停用 如果不需要此模式 将其设为 OFF

4-6. ᇄ࿑ႄ࿸ᒙ
ࠥ৖ถ፿᎖ SLOW ෝါ / AUTO ෝါ

A)

使用 Tele/Wide 键选择子菜单中的 E SENSITIVE

B)

• 使用对焦键在 X1 FIX 到 X20 FIX 之间设置 SLOW 模式

• 使用对焦键在 X1 AUTO 到 X20 AUTO 之间设置 AUTO 模式

Area1

Area2

Area3

Area0

Area4

ᔈࣅ BLC

注意 WDR 选项不适用于 LVC­C500 LVC-C510 和 LVC-C530

4-7. ᇄ࿑ႄ࿸ᒙ
ࠥ৖ถ፿᎖ AUTO (ᔈࣅ) ෝါ

A)

使用 Tele/Wide 键选择子菜单中的 FLICKERLESS

B) 使用对焦键设置模式为 OFF ON

* FLICKERLESS ᇄ࿑ႄ ፿᎖ሿ߹ᅄስ࿑ႄ

ON 开 去除闪烁

对于 PAL 制式 快门速度 1/120 秒

4-8. ౐ඡႥࣞ࿸ᒙ
ࠥ৖ถ፿᎖ AUTO ෝါ / SHUTTER ෝါ

A) 使用 Tele/Wide 键选择子菜单中的 SHUTTER
B) • 使用对焦键设置模式为 NORMAL, 1/120 - 1/50000 (NTSC)

• 使用对焦键设置模式为 NORMAL, 1/125 - 1/50000 (PAL)

4-9. ߱ဪ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

4-10. ૄᓍݩ࡝
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

AE ࿸ᒙ ᔈࣅ໎

24

AE ଀ܰ ᔈࣅ໎

25

5-1. ۳ݗޡ଀ܰ࿸ᒙ
ࠥ৖ถ፿᎖ኀখ BLC LEVEL

A)

使用 Tele/Wide 键选择子菜单中的 BLC LEVEL

B) 使用对焦键在 0 到 255 之间设置

5-2. ౑ࣅზᆍ଀ܰ࿸ᒙ
ࠥ৖ถ፿᎖ኀখ WDR LEVEL

A) 使用 Tele/Wide 键选择子菜单中的 WDR LEVEL
B) 使用对焦键在 0 到 15 之间设置

5-3. ߱ဪ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

5-4. ૄᓍݩ࡝
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

ᄂၐ࿸ᒙ

26

6. ᄂၐ࿸ᒙ
6-1. ፿ઓܪᄌ࿸ᒙ

ࠥ৖ถ፿᎖Ᏼື෵ᒦመာᔈࢾፃܪᄌ

A) 使用 Tele/Wide 键在主菜单中设置 SPECIAL SET
B) 使用 Tele/Wide 键选择子菜单中的 USER TITLE
C) 使用 Tele / Wide 和对焦键设置标题位置和数据

6-2. ༹ᇠࣞࢯᑳ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 SHARPNESS
B) 使用对焦键在 0 到 225 之间设置

6-3. ዕྻ࿸ᒙ
ࠥෝါ፿᎖ڹෝါ

A) 使用 Tele/Wide 键选择子菜单中的 COLOR
B) 使用对焦键设置模式为 ON OFF

6-4. ঌᒋ࿸ᒙ
ࠥෝါ፿᎖୓ዕྻೡࣞখܤࡵঌᒋ

A) 使用 Tele/Wide 键选择子菜单中的 NEGATIVE
B) 使用对焦键设置模式为 ON OFF

ᄂၐ࿸ᒙ

27

6-5. D ቉࿸ᒙ

ᄰࠥ৖ถࣅጲመာሤ৖ถ

A)

使用 Tele/Wide 键选择子菜单中的 D EFFECT

B) 使用对焦键设置 mode none mirror v-flip rotation

6-6. ߱ဪ࿸ᒙ

ྙ߱ဪෝါ࿸ᆐ ON

ఎ Ⴥᎌ SPECIAL ᄂၐ

৖ถ୓ۻখܤࡵ߲ޣ࿸ᒙ

A) 使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

6-7. ૄᓍݩ࡝

ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

Ꮵࣅଶހ

28

7. Ꮵࣅଶހ࿸ᒙ
7-1. ଶހෝါ࿸ᒙ

A) 使用 Tele/Wide 键在主菜单中设置 MOTION
B) 使用 Tele/Wide 键选择子菜单中的 DETECTION
C) 使用对焦键设置模式为 ON OFF

7-2. ଀ܰࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ DETECTION ON ෝါ

A)

使用 Tele/Wide 键选择子菜单中的 LEVEL SET

B) 使用对焦键在 0 到 21 之间设置

7-3.ڹᄖ/጗ᅵ࿸ᒙ
ࠥ৖ถ፿᎖ DETECTION ෝါ

A)

使用 Tele/Wide 键选择子菜单中的 DAY/NIGHT
B) 使用对焦键选择一种模式 (AUTO, DAY, NIGHT)
注意 在 LVC-C500/C503 型号中 此功能固定为 DAY

7-4. ߱ဪ࿸ᒙ
ྙ߱ဪෝါ࿸ᆐ ON

ఎ Ⴥᎌ MOTION Ꮵࣅ ৖ถ୓

ۻখܤࡵ߲ޣ࿸ᒙ

A)

使用 Tele/Wide 键选择子菜单中的 ININTIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

7-5. ૄᓍݩ࡝
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝ă

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

F OSD መာ ື෵መာ৖ถ

29

8. F OSD መာ
8-1. ৖ถ࿸ᒙ

A) 使用 Tele/Wide 键在主菜单中设置 F OSD
B) 使用 Tele/Wide 键在子菜单中选择您所需的模式
C) 使用 Tele / Wide 键和 FOCUS 键设置 OSD ON OFF 的显示

模式

*INITIAL SET  RETURN ࡼݛᒾᎧ༄ෂࡼݛᒾሤᄴ

P MASKING ۣමዚঙ

30

9. ۣමዚঙ
9-1.ཌᎮኡᐋ

此功能用于选择保密掩盖区域

A) 使用 Tele/Wide 键在主菜单中设置 P MASKING
B) 使用 Tele/Wide 键选择子菜单中的 AREA SEL
C) 使用对焦键在区域 1 到区域 8 中选择区域

9-2. ዚঙ

此功能用于 MASKING 模式

A)

使用 Tele/Wide 键选择子菜单中的 MASKING

B) 使用对焦键设置模式为 ON OFF

9-3. ۣමෝါ࿸ᒙ

此功能可转到 PRIVACY MASKING SETTING

保密掩

盖设置

模式

A)

使用 Tele/Wide 键选择子菜单中的 P MODE SET

B) 如果 PM SET END 模式转为 ON 此菜单自动转为 OFF

9-4. ጤࣅ࢛࿸ᒙ

选择要移动的点

A)

使用 Tele/Wide 键选择子菜单中的 P MODE SET

B) 使用对焦键选择 ALL X ALL Y LEFT X LEFT Y

RIGHT X RIGHT Y

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

P MASKING ۣමዚঙ

31

9-5. MOVE PT CNT

此功能可移动 MOVE PT SEL 中的选定点

A)

当 MOVE PT SEL 选择为 ALL* 时 可移动区域

B) 当 MOVE PT SEL 选择为 LEFT* 或 RIGHT* 时 改变区域

大小

9-6. ۣමዚঙ࿸ᒙஉၦ

保密掩盖设置功能可设为 OFF

A)

使用 Tele/Wide 键选择子菜单中的 PM SET END

B) 如果 PM SET END 模式转为 ON 则 P MODE SET 自动

转为 OFF

9-7. ߱ဪዕྻ

此功能用于选择初始掩盖的颜色

A)

使用 Tele/Wide 键选择子菜单中的 INI COLOR

B) 使用对焦键从颜色 1 到颜色 8 中选择模式

9-8. ዕྻ

设置完成后

选择掩盖颜色

A)

使用 Tele/Wide 键选择子菜单中的 COLOR

B) 使用对焦键从颜色 1 到颜色 8 中选择模式

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

P MASKING ۣමዚঙ

32

9-9. ߱ဪ࿸ᒙ :

A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF

9-10. ૄᓍݩ࡝ :
ࠥ৖ถ፿᎖ᅓ߲ᓍݩ࡝

A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
* 在数码变焦位置您不能设置 P MASKING 模式

P MASKING

AREA SEL
MASKING
P MODE SET
MOVE PT SEL
MOVE PT CNT
PM SET END
INI COLOR
COLOR
INITIAL SET
RETURN

NONE
OFF
OFF
NONE
0
OFF
I COLOR 1
COLOR 1
ON

ື෵ݩ࡝መာ (OSD)

33

以下某些功能在操作摄像机时
会在屏幕上显示 5 秒钟后消
失

৖ถ OSD ৃါ ႁී

1. 对焦模式 无显示 自动模式

☞

手动 / 强制自动模式

2. 背光 无显示 背光关闭
“BL”显示

背光补偿开 / 自动背光补偿模式

3. 快门速度 无显示 普通快门 (PAL: 1/50)
“Ff”显示 无闪烁模式
1/120 * 10 步

1/50,000

4. 待机 在电源打开过程中摄像机处于待机状态

5. 摄像机 ID 对每台摄像机设定识别码 可进行多点控
制 PC 控制 000~255

* 快门速度 1/120 - 1/50000 NTSC
* 快门速度 1/125 - 1/50000 PAL

12 3 6

475

ື෵ݩ࡝መာ (OSD)

34

৖ถ OSD ৃါ ႁී

6.

白平衡控 自动白平衡
制模式 室内白平衡预设 (3200°K)

室外白平衡预设 (5100°K)
手动白平衡调整 在手动模式下可使用 HUE 控制 (0 ~ 255)
强制自动白平衡 此模式打开时 白平衡自动调整 此模式关闭时

保留最后自动追踪的白平衡 手动

7. 变焦显示 DX 54 数码变焦模式 (LVC-C503/C513/C533/553)

DX 324 数码变焦模式 (LVC-C500/C510/C530)

X 27 光学变焦模式

M

W

P

W

ৃ

35

߅ስ࿸۸ 1/4"EXVIEW HAD CCD

NTSC, 高分辨率 : 811(H) X 508(V) 410K
PAL, 高分辨率 : 795 (H) X 596 (V) 470K

ၺຳܦൈ 大约 .520 TV Line

஻ᄿ X 27 变焦 (F 1.5 (W), F 3.8 (T) f= 3.25 ~ 88.0 mm), Video AF

ၫ൩ܤୡ X 2: 基本 (WDR 模式下 OFF)

X 12: 基本 (LVC-C500, LVC-C510, LVC-C530)

ᔢቃᑍී 普通模式 : 1 Lux (F 1.5, 普通快门)

(1/3 ၒ߲) 电子快门速度模式 :

0.01 Lux (X20

场积累

)

白天模式 : 0 Lux (红外开)

ቧᐅ܈ 大于 48dB

ྸහᇹᄻ

2:1

隔行

ྸහຫൈ (H) 15.734 kHz (NTSC), 15.625 kHz (PAL)
ྸහຫൈ (V) 60Hz (NTSC), 50Hz (PAL)
ۣමཌᎮ 8 个区域激活可编程区域

ৃྦᎌৎখၭݙ഍ቲᄰᒀ

36

ৃ

ୡ௦ 3.24mm (广角), 86mm (远景)
ື෵ݩ࡝መာ (OSD) 英语
࢟Ꮞገཇ DC 12V
၁ຫၒ߲ 复合输出75Ω 电阻 / Y,C 独立
৖ 5.4W: LVC-C503, LVC-C513, LVC-C533, LVC-C553

5.1W: LVC-C500, LVC-C510, LVC-C530

৔ᔫᆨࣞ 0°C - 45°C
৔ᔫဘࣞ 0% RH - 60% RH
߼ࡀᆨࣞ -20°C - 60°C, 0% RH - 85% RH
ߛࡁ 57mm(W) X 62.4mm(H) X 98.5mm(D)
ᒮ೟ 500

g

ৃྦᎌৎখၭݙ഍ቲᄰᒀ

P/NO: 3834RS0075A