LG LT923P-B User Manual

OWNER’S MANUAL

Dome Camera

Please read this manual carefully before operating your set and retain it for future reference.

MODELS LT923 Series LT723 Series

P/NO : MFL66281611

Safety Information

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modications to this equipment may cause harmful interference unless the modications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modication is made.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a conned space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Safety Information

Warning: To reduce a risk of re or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qu alied service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualied personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects lled with liquids, such as vases, should be placed on the apparatus.

Caution:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specied herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

To disconnect power from mains, pull out the mains cord plug. When instal ling the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/ EC, 2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere. The Netherlands (Tel : +31-(0)36-547-8888)

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Safety Information

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat re gisters, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Safety Precautions

• Do not attempt to disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualied service personnel for servicing.

• Avoid the camera with direct sunlight Do not aim the camera at bright objects.Whether the camera is in use or not, never face it with direct sunlight or other extremely bright objects. Otherwise blooming or smear may be caused.

• Handle the camera with care Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.

• Do not use strong solvents or detergents Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, use a mild detergent and wipe it gently.

• Do not install this camera upside down This camera is designed for mounting on the ceiling or wall.If you install this camera upside down, for example, mounted on the oor, it may cause malfunction.

• Do not use the camera in such places as shown below. The lens may become cloudy due to condensation if the camera is used under the following conditions.

› Rapid temperature uctuation by switching an air

conditioner on and o.

› Rapid temperature uctuation due to frequent

door opening and closing.

› Use in an environment where eyeglasses become

foggy.

› Use in a room lled with cigarette smoke or dust.

If the lens becomes cloudy due to condensation,

Safety Information

remove the dome cover and wipe all moist surfaces with a soft cloth.

• Before operating, please check proper temperature, humidity and power source ratings. Use the camera under conditions where temperature is from -10 °C to 50 °C and humidity is below 80 %. The input power source is AC 24 V.

• Consumables Parts having contacts such as the lens-drive motors, cooling fan built inside the camera are subject to wear with time. About replacement and maintenance of such parts, please ask the nearest service center.

Camera Installation Location

Discuss the installation location for the camera with your retailer, and select a place that is strong enough for the installation.

• Install the camera on a ceiling (concrete, etc.) at a location that is suciently strong to support it.

• Install the camera body on the foundation section of the building or sections having sucient bearing strength.

Never install or use the camera in the following locations

• Do not install it in areas exposed to direct sunlight or rain.

• Do not install the camera near the air outlet of an air conditioner.

• Near a swimming pool or other areas where chemicals are used.

• Food preparation areas and other locations where there are large amounts of steam vapor and oil, in ammable atmospheres, other special environments.

• Areas where radiation, X-rays, strong electric waves, or magnetism is generated.

• At sea, in coastal areas, or in areas where corrosive gas is being generated.

• Areas outside of the allowable ambient operating temperature range.

About Static Electricity Removal

Before installing the camera, touch a metal case or other metallic parts with your hand to remove static electricity from your body. Do not install in areas subjected to high amounts of humidity or dust. Doing so may cause internal components to damage more easily or malfunction. Do not wire cables near power lines.

Tightening the Screws

Screws should be tightened suciently in accordance with the materials and structure of the installation location. After tightening the screws, visually inspect them to make sure there is no unevenness and that each screw is tight.

Safety Information

Contents

Safety Information

16 Connecting RS-485 device

17 Connecting power source

17 Protocol and baud rate settings

18 Camera ID Setting

21 Removing the Protection Tape

22 Mounting the camera

22 Surface mount (optional)

23 Ceiling mount (optional)

25 Wall mount (optional)

4 IMPORTANT SAFETY INSTRUCTIONS

4 Safety Precautions

Preparation

8 Introduction

8 Features

9 Accessories

10 Part Names and Functions

Installation

12 Connections

12 Precautions

12 Basic Connection Overview

28 Pendant mount (Optional)

Operation

32 Setup Menu Overview

36 Menu navigation

36 Accessing the camera setup menu

36 General operation

37 Camera menu settings

37 Focus setting

37 Exposure settings

38 White Balance setting

39 Day/Night setting

39 3D-DNR setting

40 Color setting

40 Sharpness setting

13 Connecting Display device

13 ALARM input connection

15 ALARM output connections

16 Connecting LKD1000 controller

40 PAN/TILT Settings

40 Preset setting

41 Group tour setting

42 Pattern setting

43 Auto Pan setting

43 Privacy Mask setting

Contents

44 Special setting

45 Auto Tracking setting

48 OSD Settings

48 User title setting

48 ZOOM MAG setting

48 FUNCTION setting

49 DOME ID setting

49 LANGUAGE Setting

49 ALARM Setting

49 Alarm In setting

50 Alarm Out setting

50 RESET Setting

50 Information

50 Initialization

50 Factory reset

Appendix

51 Speciﬁcations

51 LT923N/P se ries

52 LT923NI/PI series

54 LT723N/P series

55 LT723NI/PI series

Preparation

2 Preparation

Introduction

Preparation

The dome cameras are designed for installation in an indoor or outdoor video surveillance system. The camera incorporates the digital signal processor, pan/ tilt mechanism, zoom lens and RS-485 communication interface in a compact outdoor enclosure.

Features

• High Sensitivity Support

The camera provides the high quality picture with

4.5 mm EX-view HAD CCD.

• Preset Position

Preset position is the function to register camera monitoring positions (preset positions). By using LKD1000 controller, you can register presets with position number. Maximum 128 Preset Positions are available. By entering the position numbers, you can move cameras to the preset positions. The moving speed and holding time are adjustable.

• Preset Tour

Preset Tour is the function to go through all the registered camera monitoring positions (preset positions). During the working PRESET TOUR, The FOCUS could not be operated properly under -10 °C (for LT723 series only)

• Group Tour

Maximum 9 group tours are able to compose the group of preset, pattern, auto pan that the operator can program to be linked together in a sequence.

• Pattern recording function

A routine of manual operations can be stored and reproduced repeatedly. The Pan, Tilt and Zoom controls are available for pattern recording.

NOTE

The available total time of pattern diers depending on camera’s operation. When the pattern recording is full, the pattern recording will automatically stop.

• Privacy Mask

Privacy zone feature enables users to veil unwanted zones. This setting is used for masking unwanted zones, hiding them from display on the monitor screen. Up to 8 zones can be registered.

• Auto Pan

The camera has an Auto Pan function that enables to keep surveillance on every detail occurring around the specic area, which is preset to watch in advance. The camera can pan among the maximum 8 points you will set. The moving speed and holding time are adjustable.

• Auto Flip

When the camera is operated to tilt through the 90°, it can be watched the opposite side of the locations by Auto Flip of a 180° horizontally.

• Optical Zoom

- LT923 series: The optical zoom range is 1x to 37x.

- LT723 series: The optical zoom range is 1x to 27x.

• Digital Zoom

Digital zoom enhances the systems zoom range to 12 times beyond the optical zoom limit. Total system zoom range is below.

- LT923 series: 37x (1x digital zoom) to 444x (12x digital zoom)

- LT723 series: 27x (1x digital zoom) to 324x (12x digital zoom)

• Alarm In function (4 channels)

Alarm input signals are supplied from external devices through the ALARM IN connector to activate ‘go to preset’ function.

• Alarm Out function (2 channels)

Preparation

When alarm inputs are supplied via the alarm input connector on the camera, the camera sends output signals via the alarm output connector on the camera.

• Controls by General Controller

This camera can be controlled by RS-485. Especially the camera has an excellent cost-saving eect because it can be controlled by the general RX point of contact signal.

• Connects with the maximum 256 cameras

This camera can be utilized after being connected with maximum 256 cameras. Therefore, it is capable of performing an excellent job in the large buildings or department stores.

• Day & Night Function

This camera can be selected Color or Black & White. You can set Color in the daytime and Black & White at night due to the low illumination. (Filter Conversion type)

• DSS (Digital Slow Shutter) function

It is possible to highly sensitive surveillance because of DSS(Digital Slow Shutter) function.

• WDR (Wide Dynamic Range) function

The camera can be best condition to watch easily inside or outside in the strong back light.

• Power Supply

This camera must always be operated a AC 24 V. Certied/Listed, class 2 power supply only.

Accessories

For LT923NI/PI series

RJ-45 Adapter cable

For LT923N/P series

Camera main cable

RJ-45 adapter cable

Preparation

Wrench

PIPE Installation Bracket

Preparation

Part Names and Functions

LT923/723NI/PI series for Indoor

Preparation

c d

e f

BNC connector cover cap

Video output BNC connector

Supplies analog video signal (composite) to the connected device.

Data Port A (RJ-45)

RS-485 data communication and input data port for alarm (relay) signal.

Data Port B (RJ-45)

Output data port for alarm (relay) signal.

This port is not used.

Power input jack

Connects to a AC 24 V power supply using proper cables.

This port is not used.

h i

Locking screw

Tighten this screw to xing the Ceiling Mount Assembly with camera body.

Dome Cover open button.

Dome Cover

Preparation

LT923/723N/P series for Outdoor

b c d

e f

a BNC connector cover cap b Video output BNC connector

Supplies analog video signal (composite) to the connected device.

c Data Port A (RJ-45)

RS-485 data communication and input data port for alarm (relay) signal.

d Data Port B (RJ-45)

Output data port for alarm (relay) signal.

This port is not used.

Power input jack

Connects to a AC 24 V power supply using proper cables.

h This port is not used. i

Dome Cover

Preparation

Installation

3 Installation

Connections

Precautions

• The following steps of installation and connection work should be done by qualied service personnel or system

Installation

installers and should conform to all local codes.

• Before you install and connect the camera, check and prepare the required peripheral devices and cables.

• Before you connect the camera, turn o all devices to be connected, such as this camera and DVR.

• Do not touch the dome cover’s window.

Basic Connection Overview

LT923/723NI/PI series (for Indoor) LT923/723N/P series (for outdoor)

Connecting Display device

The video signal connection between the camera and the monitor.

Display device connection

Installation

CAUTION

Do not connect one alarm sensor to the several camera’s alarm input connector.

Alarm input connection

ALARM input connection

You can connect up to 4 alarm sensors to the camera. Each alarm sensor should be connected with Alarm IN COM. You can adjust the signal state to NO (normally open) or NC (normally closed) through the setup menu.

1. Connect the RJ-45 Adapter cable to the PORT A (RJ-45) cable of the camera.

2. Connect the alarm device to the RJ-45 Adapter cable. When connecting lines, check and connect the color lines of the each device correctly. Refer to the below tables for color line information.

A B

C D

Alarm device

RJ-45 Adapter cable

PORT ARJ-45 Adapter cable

Port A

RJ-45 Adapter cable

No Description Color

RS-485 + White

RS-485 - Orange

NC Black

ALARM IN COM Red

ALARM IN 1 Green

ALARM IN 2 Yellow

ALARM IN 3 Blue

Installation

Alarm device

ALARM IN 4 Brown

Installation

PORT A of the LT923/723NI/PI series

Description Color

RS-485 + Red/White

RS-485 - Black/White

ALARM IN COM Red

ALARM IN 1 White

ALARM IN 2 Light Green

ALARM IN 3 Yellow

ALARM IN 4

PORT A of the LT923/723N/P series

Description Color

RS-485 + Green

RS-485 - Blue

ALARM IN COM

ALARM IN 1 Pink

ALARM IN 2 Gray

ALARM IN 3

ALARM IN 4 Violet

Pink

Yellow

White

Alarm Input function

This speed dome camera has a terminal that can sense the alarm signals. If the alarm sensor that has installed in a door, window, safe etc. sense a touch or shock, the alarm sensor send the alarm signal to the camera and the camera will observe the sensed position.

Change the observe position to a sensor that senses a touch or shock then return to the position that previously observed. (Set the Duration Time of Alarm Input function to “3 to 255”.)

Function status Mode

While observe a specic position.

While operating Preset Tour function.

While operating Auto Pan function.

While operating Pattern function.

in case of HOME POSITION is ON.

Change the observe position to the alarmed position then return to the position that previously observed.

Stop preset touring and change the observe position to the alarmed position then restart the preset touring again.

Stop auto panning and change the observe position to the alarmed position then restart the auto panning again.

Stop operating pattern function and change the observe position to the alarmed position during the dwell time then restart the pattern function again.

After Alarm has been cleared and nished the dwell time, it moves to the HOME POSITION and spend the dwell time at that position.

NOTE

During the dwell time for alarm, you can not control the controller.

Installation

ALARM output connections

Connect the alarm device to the alarm output data port. Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode.

1. Connect the RJ-45 Adapter cable to the PORT B (RJ-45) cable of the camera.

2. Connect the alarm device to the RJ-45 Adapter cable. When connecting lines, check and connect the color lines of the each device correctly. Refer to the below tables for color line information.

Alarm Out connection

A B

C D

E F

G H

Alarm device

ALARM OUT [NC2] Blue

NC Brown

PORT B of the LT923/723NI/PI series

Description Color

ALARM OUT [NC1] Blue

ALARM OUT [COM1] Violet

ALARM OUT [NO1] Brown

ALARM OUT [NC2] Gray

ALARM OUT [COM2] Orange

ALARM OUT [NO2] Black

PORT B of the LT923/723/N/P series

Description Color

ALARM OUT [NO1] White Blue

ALARM OUT [COM1]

Installation

Beige

RJ-45 Adapter cable

PORT BRJ-45 Adapter cable

Port B

RJ-45 Adapter cable

No Description Color

ALARM OUT [NO1] White

ALARM OUT [COM1] Orange

ALARM OUT [NC1] Black

NC Red

ALARM OUT [NO2]

ALARM OUT [COM2] Yellow

ALARM OUT [NC1] Black

ALARM OUT [NO2] Brown

ALARM OUT [COM2] Red

ALARM OUT [NC2] Orange

Green

PORT A

RJ-45 Adapter cable

PORT A

TX-

TX+

RJ-45 Adapter cable

PORT A

RJ-45 Adapter cable

Installation

Connecting LKD1000 controller

1. Connect the RJ-45 Adapter cable to the PORT A (RJ-45)

2. Connect the LKD1000 controller to the RJ-45 Adapter

LKD1000 connection

Installation

RJ-45 Adapter cable

Connecting RS-485 device

Use the cable that is described below for RS-485 site communication.

• Shielded, twisted pair cable

• Low impedance

• Wire gauge size is thicker than AWG #22 (0.33 mm2).

cable of the camera.

cable. (Refer to the manuals of the LKD1000 controller for more details.)

TX+

C D E F G

TX-

RJ-45 Adapter cable

Port A

No Description Color

RS-485 + White

RS-485 - Orange

RS-485 connection

C D E F G

RJ-45 Adapter cable

RS-485 device

Port A

1. Connect the RJ-45 adapter cable to the PORT A (RJ-45) cable of the camera.

2. Connect the RS-485 device to the RJ-45 Adapter cable. When connecting lines, connect the “Orange color line” of the RJ-45 Adapter cable to “RX -” of the RS-485 unit and “White color line” of the RJ-45 Adapter cable to “RX +” of the RS-485 unit correctly.

RJ-45 Adapter cable

No Description Color

RS-485 + White

RS-485 -

Orange

PORT A of the LT923/723NI/PI series

Description Color

RS-485 + Red/White

RS-485 - Black/White

PORT A of the LT923/723N/P series

Description Color

RS-485 + Green

RS-485 - Blue

Installation

Connecting power source

Connect a AC 24 V power source to the power input jack.

Protocol and baud rate settings

The camera has one 8-bit DIP switch blocks that determine the protocol and baud rate of the data communication. Settings are loaded when the camera boots up. Be sure to turn the camera o, change the DIP switch settings, and then power the camera back up to load the changes.

1. Turn o the camera.

2. Remove the dome cover.

3. Remove the camera assembly cover.

4. Set the DIP switches.

DIP switch locations

Baud Rate setting

DIP switch position

SW1 SW2 SW3 SW4

OFF OFF OFF OFF 9 600

OFF OFF OFF ON 2 400

OFF OFF ON OFF 4 800

OFF ON OFF OFF 19 200

ON OFF OFF OFF 38 400

ON ON ON ON OSD Set

BAUD RATE

(BPS)

Protocol setting

DIP switch position

SW5 SW6 SW7 SW8

OFF OFF OFF OFF LG Multix

OFF OFF OFF ON Pelco D

OFF OFF ON OFF Pelco P

ON ON ON ON OSD Set

OFF

Installation

OFF

Protocol

5. Assemble the dome cover and the camera assembly cover in the reverse order.

6. Power up the camera to load the changes.

NOTE

If you are not using the controller with LG Multix protocol, there may be some limitation of function control.

+ 39 hidden pages